Hi everyone.
I'm not in panic, but i'm close to it.
After hardspl done, i flash to Shadow 2.0 and everything goes ok.
Then, it stuck at bootloader! Softreset, hardreset, nothing helps, and worst, i can't connect to pc with usb!! simply can't connect!!!
I've done everything i can. search a lot, read a lot, and nothings help!!
so, please help me!!
(sorry my bad english)
is your battery more fully charged? (or at least 50%)
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
mc_falco said:
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
Click to expand...
Click to collapse
Try connecting the usb and running aku 2.2 WM5. That worked for me before other times.
I Am Not Pretty Sure But It Might Help U Out!
mc_falco said:
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
Click to expand...
Click to collapse
why not try to do old way of flashing and it might help coz'
it help me when i had bootloder stuck.
i try with Prophet_PV_Temp. rom
and it went everything good .
thanks
Take off battery and place it back, switch on. What happens?
Regards,
Carty..
First thing to try: search and read WIKI:
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
Perhaps the links to the AKU/NVID are dead, I didn't check, but you can use any official ROM to get your phone back.
You MUST disable the 'connect through usb' option in AS before it will work.
Please Help I Have Done Everything But Cannot Get My Prophet To Connect Via Usb.
I TRIED EVERYTHING. I have bootloader screen but when i connect through USB it just says that device not recognized and nothing would happen. I even took the battery out for 2 hours... put in another phone charged to maximum and still same problem. Please if anyone could help.. i love this phone cant let it die like that.
I have ni ideas other than that you are doing something wrong...
l3v5y said:
I have ni ideas other than that you are doing something wrong...
Click to expand...
Click to collapse
Well I used the upgrade guide and i have done upgrades before and everything went fine. Except today when i tried the new way and tried to load the New Shadow Rom. all was done ok but when the phone restarted it just stucks at the bootloader. and since then it wont connect through USB . the PDA wont get recognized at all.. any ideas?
Use the 'old' upgrade method, and recover using an official wm5 rom from the ftp server. you must disable connect through usb in active sync... see the wiki for more details (prophet recovery)
please go to the link in my
signature...
Should Help!
I've bricked my S200 after an error in uploading 4.0.0.6 and after going thru the wiki steps... it's working again
Related
Hey everyone,
Can anyone help me fix this big problem.
I downloaded a update ROM from (http://www.xda-developers.com/incoming/rom160wwe/) with the name RUU16006WWE_T-mobile_NL.exe.
After trying to upgrading my device, the proces stopped and told me that there was a connection problem. After this, a tryed to re-connect my device to my computer and to finish the upgrade bud nothing happend and stil nothing happens. My T-mobile MDA is not responding to anything. And i can't connect to ActiveSync. The only thing that my mda shows is this (click on the picture too enlarge).
So ones again. HELP me PLEASSSS..... Send any comments to [email protected]
I hoop my Mda can be fix cause it cost me alot.
Don't panic Your device is in bootloader mode.
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require ActiveSync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks for the fast replay bud....
Can you give me a specific step by step to do it the right way? I m not verry good in this kind of things... Thx anywhy
For the moment, hopefully, all you need to do is what I said above. Re-running the upgrade should work OK (although it may depend on what version ROM you had installed already). Give it a try and see what happens.
Wel it keeping telling me that RAPI.dll is missing. Even when i have downloaded RAPI.dll.
I had version 1.60 i think.
Do you no where i can download the version that i had?
Try re-installing Activesync. The latest version is 3.7.1 Build 4034.
You can get it from here: http://www.microsoft.com/downloads/...7c-ca96-48b4-b5d4-f3e047ca5108&DisplayLang=en
OK thx i wil try that...
I have stil a problem.
Where can i download the ROM version 1.60.00WWE? Cause i'm upgrading with 1.66 bud it showed an error
The same error? And at what point does it happen?
Also, please confirm which ROM you are trying to upgrade with, as you have stated two different versions so far.
dcs i'm sorry you're right.
Well, i'm now upgrading from nothing (it showed what ROM i currently have, nothing) to 1.60.06WWE. I download it from http://www.xda-developers.com/incoming/rom160wwe/ as i sad before. It has the name RUU16006WWE_T-mobile_NL.exe
reply for more info.
OK. So what is the current situation? Are you still having a problem? If so, what are the details and exactly when does it occur?
Yes, i still got some problems. One of the many is dat after a few min. or so later, the proces stops and i get an error. I have to do a soft reset and start the proces again. So i did.
Bud now i can't connect anymore. What you see below is what i constantly get to see. And it wil do nothing.
How long have you waited with that message displayed? It can sometimes take a while to get started properly. At that time can you see what is displayed on the device?
The picture that i just showed you, i get that immediatly after pushing next in the beginning field.
When the display (see picture) is shown, the display of my device is blank. There is nothing, no words.
OK. Just be to be sure. Put the device in boot loader mode by pressing and holding the jog button (bottom centre of device) and the power button at the same time and press reset button. This should show the bootloader screen with (in your case) Serial V1.03 displayed. Put the device in the cradle and it should say USB V1.03. Then restart the upgrade. When the initial screen displays on the PC click next and the screen you posted above will display while the PC handshakes with the device. Give this some time to complete. If all is well it will progress to the screen showing the versions, etc. and allow upgrade. Click upgrade and again it will show the screen you posted above for a while then (hopefully) continue.
I'm now bizzy with what you sad. 10min. so far.
10 Minutes with the display you posted above? If so then that is too long
Yes exacly... TOO long... i don't no what to do now.. anyways. I'm going to sleep now. I wanna thank you for everything.. I'll hope to speek too you tomorrow. Bye bye
OK. Sorry we couldn't get it sorted tonight . If I think of anything else I'll let you know.
Another thought came to me. Some people who have had this sort of problem found that using a different USB port or even another PC solved the problem.
Ok, so I tried to flash my G4 wizard to wm6, went all the way through the flash, got to 99% and stopped, giving me a comm error. I did the recovery and im in an endless flash to 99% loop. When I turn it on, I get the bootloader (3 stripe) screen, with the following:
RUU upper right corner
IPL 2.25.0001
SPL 2.25.0001
USB lower left corner.
I have spent the last 4 hours reading posts and cannot fix this thing. Any help would be greatly appreciated.
did u flash it back to carrier rom?
Flash it back to the original carrier ROM (should be available on the website) and then use ShellTool to flash the ROM. make sure that you follow the instructions exactly, otherwise, you will end up with a bricked rom.
-Nstefanelli-
The only rom I can find on Cingular's web site, once downloaded says its corupted, and I cant find one on XDA at all. Anybody know where else I might find one?
Wizard Love rom is another one you could try.
Wizard Love got me goin again, I love me some wizard.
Thanks for the help guys!!!
Same Problem I Have Faced.... And Also Solved.
u have Radio Rom problem....
search the latest radio rom and upload to your rom... and restart your pda...
reply me..... sooon because same problem i had faced and solved also.
Same problem
I was having the same problem yesterday. Eventually i got it to work again. It was a little confusing though because i used the rom from the HTC website to get it up and running again with wm5 and then used ShellTool from the sticky in this forum to flash it with a wm6 rom. From what i gather it's because my phone was CID locked, something that none of the roms include in their instructions to watch out for. Maybe a sticky in the forum for newbs like me containing things to watch out for while flashing roms?
A side note:
I had to download the rom from the HTC site twice in order for it to flash back to the original OS. The first time i downloaded the rom i kept getting an error. I guess it was a bad download or something but the second one worked in the first shot.
think i bricked my wizard
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
gripper said:
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
There is no help for you if you did flash a non-official G3 rom onto your phone.
Recent Official carrier releases are the only roms that contain bootloaders that are safe to flash into a G4. (Note older carrier releases could possibly fry your phone as well as they may not contain G4 bootloaders)
If you flashed a custom rom with IPL/SPL your device is done for good.
Though you said it went to the bootloader prior to going dark so you may just have a dead battery and a bad flash. Get a battery from a friend or buy one and then see if the device will power on. If you can't get it to power on with a known good battery then it is most likely fried. If it does boot at least to bootloader then you should be able to recover your device. Most chargers will not charge the battery of your phone unless the phone is fully booted into windows. So it is very important to have a contingency plan in case of a bad flash with these phones as playing/troubleshooting while trying to recover from a bad flash will drain your battery possibly leaving you with not enough juice to complete a flash.
hi zzan
thanks for the reply, i think your right about the battery it actually turns on for about 10 seconds now into bootloader but then the battery dies again so i gonna source a battery.
gripper said:
oops !!!!
think i flashed a g3 rom onto my g4 wizard and for a while it stayed in bootloader screen (tricolour) now the wizard is dead with no charging light when plugged in and performing hard reset does nothing
please help !!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Remove the battery for about 5 minutes, then put it back in.. then try booting in bootloader mode <tri color screen> .. then flash with an OFFICIAL Carrier ROM ..
I flashed my hermes yesterday <changing the spl and stuff> and it was dead for a little bit, until I took the battery out and put it back in.. <for some reason it was like a de-fibrilator..>
Try that.
hi madcap,
not looking good i toook it to a phone engineer and he says it is corrupt ? he has tried flashing it, apparently there is a guy who will put in a new chip ? i am such a fool i bricked my phone just to get rid of o2 stuff !!!!!
gripper said:
hi madcap,
not looking good i toook it to a phone engineer and he says it is corrupt ? he has tried flashing it, apparently there is a guy who will put in a new chip ? i am such a fool i bricked my phone just to get rid of o2 stuff !!!!!
Click to expand...
Click to collapse
A new chip?!?!??
The problem is the in the IPL area which can now be flashed only via JTAG (cable system that doesn't require booting files since it operates directly on the chip)
Take it to an official repair.
Hi,
I have almost the same problem. I tried to flash to WM6.1 for wizzard, it got to 99% and failed (connection lost). I then tried the recovery process but that didnt work.
Now I can boot to the booloader, and see the IPL/SPL versions (2.25.0001) and can see USB on the lower left. But , it is not making a connection to my PC. None of the RUU, ROMS, HardSPL, or SoftSPL apps can connect to it.
They all report some connection error, "Device not found", or "Connection Error 264"...
I have read a bunch on this forum, and tried alot of stuff but nothing worked.
I started up my own thread on my issue, but hope someone could help me, help someone else in the process here..
How can I get this thing flashable again?
Thanks
Madcap180 said:
Remove the battery for about 5 minutes, then put it back in.. then try booting in bootloader mode <tri color screen> .. then flash with an OFFICIAL Carrier ROM ..
I flashed my hermes yesterday <changing the spl and stuff> and it was dead for a little bit, until I took the battery out and put it back in.. <for some reason it was like a de-fibrilator..>
Try that.
Click to expand...
Click to collapse
This worked for me and now I can connect the apps to the phone again. But after I try to install the default rom, everytime at 80% it looses the connection again.. .
Anyone know a good WM6.1 rom that works with 8125 G4
end123 said:
This worked for me and now I can connect the apps to the phone again. But after I try to install the default rom, everytime at 80% it looses the connection again.. .
Anyone know a good WM6.1 rom that works with 8125 G4
Click to expand...
Click to collapse
Fully recharge your battery, then try to flash again. Low/dead/misreporting battery will kill a flash as surely as disconnecting the cable in mid-flash. Oh, and try WizFlo...really cool! (I had to fiddle with the Opera Browser install to get the Internet connection to work correctly, but who cares, it was worth it!)
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Please try the search button in this forum!!! And don't worry it's not bricked;-)
sayjeng said:
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Click to expand...
Click to collapse
check your .NET Framework and see if you have the 2.0 version installed. Reboot your pc and start again. We always experience these hiccoughs.
i've tried the search..
seriously saying, its quite hard to find what i want..
i seem to be able to flash the PV_TEMP ROM, it says on my computer its successful but my PDA just goes back to bootloader.
anyway, i'm installing .Net framework 2.0... will see how that goes..
still doesn't work..
RUU says its congratulations...
PDA goes back to bootloader
i cna flash jester's rom, i can flash PV_temps rom..
but all i get is the bootloader screen after that..
can't flash the NVID thats from the upgrade guide... it just says wrong NBF file..
wonder how much will it cost for me to send it to service center to replace the whole flash chip
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
sayjeng said:
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
Click to expand...
Click to collapse
so you know now what is the problem!
recharge it by connecting to a PC with USB and wait wait wait and hope for the best. Try recharging it by what ever means you can do. If you said, you are successful in getting PVtemp, then, try installing battery_status.cab (find it search it by google or whatever) and watch the battery_status line on the front page and wait for a + sign before the 100mA at the right bottom line to appear.
Wait till it is full, then redo step 2 again. I'm sure you can get over without getting the machine to the manufacturer for repair.
no no
the first problem still stands
i'm still stuck at bootloader..
but now i can't flash anything cause my batt is dead..
so i've got 2 problems now
hello all,
sayjeng, I got the same problem last week.
I couldn't use any RUU rom because of the corrupted nbf file.
The PV_TEMP rom worked but I was stuck on boot loader screen too...
I tried many times and with some random hard resets... Eventually, the fourth time , WM5 started...
My advice are :
- charge your battery by any means like SeaPea said
- reboot your desktop computer
- remove your (fully charged) battery from your phone for some seconds and put it back...
Really, I may have been lucky that time...
I just wanted to post here to say that I sympathize...
Good luck!
will give it a try tomorrow..
its past 1am now and i need to be up early tomorrow..
if it doesn't, really have to make a trip to service center..
wonder what should i tell them then..
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
sayjeng said:
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
Click to expand...
Click to collapse
me too....any progress?
Jow ... flash your rom from dopod!
If your Radio Rom is crashed ... it stuck at Bootscreen too! After that it must run! it fix partition errors too.
ROm from dopod is 2.15..
my prophet is now on 2.20...
i can't flash it... i haven't been able to find a vendor rom wiht 2.20..
does anyone have any ? Qtek maybe ?
something to get my prophet running...
cause i did try in my attempt to get my prophet back by flashing the Radio ROM.. and it fails.. maybe thats why i can't boot my prophet
tried almost every rom..
used almost every RUU
anyone got any RUU that might help ?
or any suggestions ? thinking of throwing the towel and just pass it to dopod for them to handle....
worst case, change ROM chip
finally
I got this to work using the guide - BUT:
Windows XP SP2 English was the key for me.
I used VMWare to do step 1 of flashing (NVID)
then step 2 of flashing I did on a separate PC.
Worked after so many different attempts
i am running on XP sp2 english.. not using vista..
problem is, i can't even hard reset my phone.. it just says Format is Failed.
but my phone seems fine and still responds to my plugging the USB in and reseting....
Hi sayjeng
The same problem with my imate jamin too..
Whatever you said in you posts is an exact recall of my case.
Now it makes two of us
Waiting to see if someone can come up with a solution.
IPL/SPL at 2.20
Frequent automatic disconnection from activesync.
No means to charge the battery which i think is almost dead.
Tried the Dopod rom,for no avail.
The list goes on and on just like yours.
help..Anyone..?
My 7500 had mobile 6 on it for a while and every thing worked great. I installed MichyPrima's 6.1 ROM spl 1.2 and everything works great EXCEPT no Wifi at all. Comm Manager will turn on wifi but when I go to Wireless Lan in the settings area and click on "Turn on WLAN" it works on it a couple of seconds and then nothing. I can not get the wifi to turn on. Is there a fix for this particular WLAN problem? Thanks.
babyhemi said:
My 7500 had mobile 6 on it for a while and every thing worked great. I installed MichyPrima's 6.1 ROM spl 1.2 and everything works great EXCEPT no Wifi at all. Comm Manager will turn on wifi but when I go to Wireless Lan in the settings area and click on "Turn on WLAN" it works on it a couple of seconds and then nothing. I can not get the wifi to turn on. Is there a fix for this particular WLAN problem? Thanks.
Click to expand...
Click to collapse
Welcome to the forum.
I noticed that pdajoy helped you when you tried to load WM6.5 onto your athena.
This is an SPL 3.5 rom and doing this is probably what broke your WIFI.
It is mentioned a few places in this forum and wiki but can be hard to find the solution
read these
http://forum.xda-developers.com/showthread.php?t=387454
http://forum.xda-developers.com/showthread.php?t=405814
You should read this http://forum.xda-developers.com/showthread.php?t=429013
and also the wiki
lakeman said:
Welcome to the forum.
I noticed that pdajoy helped you when you tried to load WM6.5 onto your athena.
This is an SPL 3.5 rom and doing this is probably what broke your WIFI.
It is mentioned a few places in this forum and wiki but can be hard to find the solution
read these
http://forum.xda-developers.com/showthread.php?t=387454
http://forum.xda-developers.com/showthread.php?t=405814
You should read this http://forum.xda-developers.com/showthread.php?t=429013
and also the wiki
Click to expand...
Click to collapse
Thanks for the info. I probably did something wrong I tried the ap 4.0 update and I bricked my 7500 the most I can get is my multi colored screen my computer does not recognise my device so I can not do anything else.
babyhemi said:
Thanks for the info. I probably did something wrong I tried the ap 4.0 update and I bricked my 7500 the most I can get is my multi colored screen my computer does not recognise my device so I can not do anything else.
added that phone will now not turn on
Click to expand...
Click to collapse
OK.
stop everything
read the links I gave you.
Don,t do the following till you have a bit of understanding of how you got where you are now.
.
.
.
.
Remove the battery for 30 secs(you should have already removed the sim and sd card)
.
turn on the phone (assuming you have the phone fully charged)
.
Press the camera button in fully and press the reset button.
.
You should now be in Bootloader
(if you don't know what this is you haven't read enough)
.
You can load a rom from here but it has to match the SPL that is shown in the bootloader screen.
.
The SPL should be either 1.2 or 3.5
If it is not, then you haven't unlocked your phone.
.
I am also guessing you have corrupted the phone id.
Please don't do anything more till you go through the above process and attempt to search for a solution.
I suggest you clear your attempted solution by asking here first
Is there anything at all I can do?
What can I do? Is there anything at all I can do with my 7500, I think I totaly bricked my device. It will not do anything not even the multi-color boot screen when you push the buttons. The hard reset does nothing at all and my computer does not recognize it at all. Is it just a "brick"?
babyhemi said:
What can I do? Is there anything at all I can do with my 7500, I think I totaly bricked my device. It will not do anything not even the multi-color boot screen when you push the buttons. The hard reset does nothing at all and my computer does not recognise it at all. Is it just a "brick"?
Click to expand...
Click to collapse
sometimes the battery is not seated properly
try plugging into the mains charger and fiddling with the battery till the charging light comes on.
If this happens , let it charge till the light goes green and try what I said again
Hey, to make a long story shorter i tried to root it but did not succeed.. fully.. haha, well it all went smooth until i wanted to go in to recovery first time
after unlocking bootloader, i couldnt get in there, so i erased cache and tried again, and different methods then i started to try to flash another recovery img, didnt want to work and still i could not get in to recovery.... tried to lock and unlock bootloader and other things and nothing....
So i did it from scratch,. but i couldnt even do factory reset from bootloader, couldnt do anything from there really... and then it didnt want to boot normally for some reason, i might just have been impatient but... so i started flashing in another boot.img.... dont ask me why but in the end when i felt there was no more hope i started flashing in everything i had, more or less.. what i think got f'ked up is the Kernel.
i used this guide http://forum.xda-developers.com/showthread.php?t=2069904 and used that all in 1 tool most of the time, but also tried manual commandands via fastboot..
.
when it locked up totally, it didnt want to boot normally after that i could just get in to bootloader, so i sat all day yesterday putting posts in different threads in several forums so dont say i havent looked ^^
i didnt get any answer anywhere in time and it got uncharched, and was dead since yesterday so i gave up, until today, i couldnt charge it.. but i tried now and from nowhere i could get into bootloader again but this time with too low battery to flash!!
and i dont think its charging properly, dont know why exactly.. so im just sticking the usb cable in and out while its powered off since the red Led just light up for a sec when inserted then nothing, just to maybe get some power in there...
so im kind of at a cricis here, and would need help since i dont have anymore time to try to fix it
dont know exaclty what info you need, dont want to boot in unneccesary right now so just ask if u need any numbers or whatever..
i bought it very recently here in sweden.. dont rly know what more information i can give
Would surely appreciate some solid help!
Sincerely, jeff
VivaSativa said:
Hey, to make a long story shorter i tried to root it but did not succeed.. fully.. haha, well it all went smooth until i wanted to go in to recovery first time
after unlocking bootloader, i couldnt get in there, so i erased cache and tried again, and different methods then i started to try to flash another recovery img, didnt want to work and still i could not get in to recovery.... tried to lock and unlock bootloader and other things and nothing....
So i did it from scratch,. but i couldnt even do factory reset from bootloader, couldnt do anything from there really... and then it didnt want to boot normally for some reason, i might just have been impatient but... so i started flashing in another boot.img.... dont ask me why but in the end when i felt there was no more hope i started flashing in everything i had, more or less.. what i think got f'ked up is the Kernel.
i used this guide http://forum.xda-developers.com/showthread.php?t=2069904 and used that all in 1 tool most of the time, but also tried manual commandands via fastboot..
.
when it locked up totally, it didnt want to boot normally after that i could just get in to bootloader, so i sat all day yesterday putting posts in different threads in several forums so dont say i havent looked ^^
i didnt get any answer anywhere in time and it got uncharched, and was dead since yesterday so i gave up, until today, i couldnt charge it.. but i tried now and from nowhere i could get into bootloader again but this time with too low battery to flash!!
and i dont think its charging properly, dont know why exactly.. so im just sticking the usb cable in and out while its powered off since the red Led just light up for a sec when inserted then nothing, just to maybe get some power in there...
so im kind of at a cricis here, and would need help since i dont have anymore time to try to fix it
dont know exaclty what info you need, dont want to boot in unneccesary right now so just ask if u need any numbers or whatever..
i bought it very recently here in sweden.. dont rly know what more information i can give
Would surely appreciate some solid help!
Sincerely, jeff
Click to expand...
Click to collapse
Dude I just googled ur problem......
found a possible solution from HTC One X forum http://forum.xda-developers.com/showthread.php?t=2148689
refer Post #4 the bat file might solve ur problem
Anyways I would like u to confirm it with some senior developers(PM them)
I'm sure they ll help u out.....
Good luck
Danny Samuel said:
Dude I just googled ur problem......
found a possible solution from HTC One X forum http://forum.xda-developers.com/showthread.php?t=2148689
refer Post #4 the bat file might solve ur problem
Anyways I would like u to confirm it with some senior developers(PM them)
I'm sure they ll help u out.....
Good luck
Click to expand...
Click to collapse
it aint that easy.. ive been to several threads that were it was similiar problems, tried all those similiar solutions aswell.. this one was nowhere close to my solution
i tried it but now again its stone dead cant even get in to bootloader so computor just says waiting for device.
who are these senior developers and where do i find them??...
what recovery are you using
Lloir said:
what recovery are you using
Click to expand...
Click to collapse
i was trying to use the TWRP 2.4.1.0 at first, then tried clockworks with no success..
now i think i want to download some fresh ones... again
VivaSativa said:
i was trying to use the TWRP 2.4.1.0 at first, then tried clockworks with no success..
now i think i want to download some fresh ones... again
Click to expand...
Click to collapse
just plug the phone into the wall, leave it for a day or so.
Lloir said:
just plug the phone into the wall, leave it for a day or so.
Click to expand...
Click to collapse
alright, that might solve my battery problem... but then what? my problem still consists...
then flash a correct twrp\boot.img\rom
Lloir said:
then flash a correct twrp\boot.img\rom
Click to expand...
Click to collapse
that is what ive been trying all along, tried to clear cache.. but it seems like the first one i got in there wont go away and is priotized or something..
it was this morning i tried for fun to press power and it started i was like wtf because it wasnt plugged in.. then i plugged it in to start this thread its been shut down and plugged in the wall since i put this thread, around 12.. and i cannot start in into bootloader again, completely dead for now..
if i insert it in to my pc the red LED flashes 3 times if i put it in the wall it flashes steady 1 time. but does not seem to get any charge from either
VivaSativa said:
it was this morning i tried for fun to press power and it started i was like wtf because it wasnt plugged in.. then i plugged it in to start this thread its been shut down and plugged in the wall since i put this thread, around 12.. and i cannot start in into bootloader again, completely dead for now..
if i insert it in to my pc the red LED flashes 3 times if i put it in the wall it flashes steady 1 time. but does not seem to get any charge from either
Click to expand...
Click to collapse
Your battery is critically low.
As already advised by lloir... Just plug it in to the charger, and may forget for a good 24 hours so that the phone exists....
Addicted2xda said:
Your battery is critically low.
As already advised by lloir... Just plug it in to the charger, and may forget for a good 24 hours so that the phone exists....
Click to expand...
Click to collapse
i will do that, its still in the wall and shut off, and try some solution tomorrow, but i still dont quite have that solution ^^
Once charged, you could download the correct RUU, flash that, and restart from scratch. You may have to relock the bootloader using Hasoon's toolkit. After that, its not complicated - use Hasoon's kit to unlock again, flash the correct recovery, sideload a ROM and boot up your phone.
surfatwork said:
Once charged, you could download the correct RUU, flash that, and restart from scratch. You may have to relock the bootloader using Hasoon's toolkit. After that, its not complicated - use Hasoon's kit to unlock again, flash the correct recovery, sideload a ROM and boot up your phone.
Click to expand...
Click to collapse
i have the correct RUU on my desktop, i searched for ages before i found it, but this is an .exe and starts a program for me and have failed at the last part.. i cant try it now so i can see what it said and i cant remember exactly at what step it failed.. i came like halfway in to it
or do you mean the ruu.zip version? to flash it manually into the device?
did you relock the bootloader? the error message might help
surfatwork said:
did you relock the bootloader? the error message might help
Click to expand...
Click to collapse
relock it for what step, i tried to lock and and unlock it several times
seriously, you need to read atleast a little bit - a million people before have posted exactly the same questions, have had answers posted umpteen times. you need to relock the bootloader before you run the RUU.
surfatwork said:
seriously, you need to read atleast a little bit - a million people before have posted exactly the same questions, have had answers posted umpteen times. you need to relock the bootloader before you run the RUU.
Click to expand...
Click to collapse
well sorry for acting Stupid but i just want to be completely sure since ive been at it since friday now
if i get it to start tomorrow, i think ill start with the .bat file to get it to charge some more, then relocking the bootloader, then flashing a proper ruu..
is these steps somewhat correct??
no one??? i got it to boot a short time today then stone dead again so there is some hope