Hey everyone,
Can anyone help me fix this big problem.
I downloaded a update ROM from (http://www.xda-developers.com/incoming/rom160wwe/) with the name RUU16006WWE_T-mobile_NL.exe.
After trying to upgrading my device, the proces stopped and told me that there was a connection problem. After this, a tryed to re-connect my device to my computer and to finish the upgrade bud nothing happend and stil nothing happens. My T-mobile MDA is not responding to anything. And i can't connect to ActiveSync. The only thing that my mda shows is this (click on the picture too enlarge).
So ones again. HELP me PLEASSSS..... Send any comments to [email protected]
I hoop my Mda can be fix cause it cost me alot.
Don't panic Your device is in bootloader mode.
Just reset the device, place it back in the cradle and re-run the upgrade. It doesn't require ActiveSync as the upgrade process looks after its own connection.
Make sure the cradle is connected directly into a USB port on your PC and not to a hub. Also make sure the power supply is connected to the cradle.
Thanks for the fast replay bud....
Can you give me a specific step by step to do it the right way? I m not verry good in this kind of things... Thx anywhy
For the moment, hopefully, all you need to do is what I said above. Re-running the upgrade should work OK (although it may depend on what version ROM you had installed already). Give it a try and see what happens.
Wel it keeping telling me that RAPI.dll is missing. Even when i have downloaded RAPI.dll.
I had version 1.60 i think.
Do you no where i can download the version that i had?
Try re-installing Activesync. The latest version is 3.7.1 Build 4034.
You can get it from here: http://www.microsoft.com/downloads/...7c-ca96-48b4-b5d4-f3e047ca5108&DisplayLang=en
OK thx i wil try that...
I have stil a problem.
Where can i download the ROM version 1.60.00WWE? Cause i'm upgrading with 1.66 bud it showed an error
The same error? And at what point does it happen?
Also, please confirm which ROM you are trying to upgrade with, as you have stated two different versions so far.
dcs i'm sorry you're right.
Well, i'm now upgrading from nothing (it showed what ROM i currently have, nothing) to 1.60.06WWE. I download it from http://www.xda-developers.com/incoming/rom160wwe/ as i sad before. It has the name RUU16006WWE_T-mobile_NL.exe
reply for more info.
OK. So what is the current situation? Are you still having a problem? If so, what are the details and exactly when does it occur?
Yes, i still got some problems. One of the many is dat after a few min. or so later, the proces stops and i get an error. I have to do a soft reset and start the proces again. So i did.
Bud now i can't connect anymore. What you see below is what i constantly get to see. And it wil do nothing.
How long have you waited with that message displayed? It can sometimes take a while to get started properly. At that time can you see what is displayed on the device?
The picture that i just showed you, i get that immediatly after pushing next in the beginning field.
When the display (see picture) is shown, the display of my device is blank. There is nothing, no words.
OK. Just be to be sure. Put the device in boot loader mode by pressing and holding the jog button (bottom centre of device) and the power button at the same time and press reset button. This should show the bootloader screen with (in your case) Serial V1.03 displayed. Put the device in the cradle and it should say USB V1.03. Then restart the upgrade. When the initial screen displays on the PC click next and the screen you posted above will display while the PC handshakes with the device. Give this some time to complete. If all is well it will progress to the screen showing the versions, etc. and allow upgrade. Click upgrade and again it will show the screen you posted above for a while then (hopefully) continue.
I'm now bizzy with what you sad. 10min. so far.
10 Minutes with the display you posted above? If so then that is too long
Yes exacly... TOO long... i don't no what to do now.. anyways. I'm going to sleep now. I wanna thank you for everything.. I'll hope to speek too you tomorrow. Bye bye
OK. Sorry we couldn't get it sorted tonight . If I think of anything else I'll let you know.
Another thought came to me. Some people who have had this sort of problem found that using a different USB port or even another PC solved the problem.
Related
I've done all search BUT still can not solve out my problem.
I tried to upgrade my current ROM (1.03) to 1.60 BUT when upgrade in process; suddenly it said cannot find the device(XDAII).
At that time I took out the machine from cradle and did soft reset. And put it back to cradle to continue upgrade. And the error message still said it still can not find the device.
When I tried to enter into Bootloader mode and USE ROM on SD to restore my original ROM, BUT I tried the method mentioned in some post;
still cannot go to BOOTLOADER mode. On the screen it always said " Serial on the top.
Could anyone help me please?
I have the same problem..
i even tried with Qtek Rom, MDA rom... still not working.
When I turn on the xda II, it only displaying serial on top and v.1 06 at bottom.
tried to run the xdaII upgrade rom with the error :
ERROR 100 : MODEL ID ERROR 1-N-PH-PH-PH
If I try with QTEK and MDA Rom it just does nothing, or it hangs for a long time..
I have tried many times and still not working..
please anyone..
I have the same problem, people, pls help
rom update from sd card
hello,
i did had this also on my old mda..
i fixed it with a rom update on a sd card
good luck
still waiting for a good working 2003 se for my mda2
XDAII stuck in bootloader
mine too , stuck in bootloader with written :
SERIAL V1.06
nothing else ,
what can we do pals ?
no one try to help ????
please ?????
thanks
steve
if you have something written on the screen; such as SERIAL V1.06 then in my opinion you're still okay. do a couple of hard resets, put the unit back on the cradle and double click the upgrade file again. a lot of chaps ran into this same problem but eventually got it going again.
cheers
Thanks Robson..
I did that last nite , but still facing same probs .....
by the way , how to drain my batt ? just take out from the unit for 1 hour ?
and it will automatically drainned ? pls tell me ... thanks before...
Hope this is help...
I have the same problem b4, its frustating to see my XDA become an "expensive brick". After trying everything finally worked. What i did, after u turn on your computer plug in the cradle and also put the XDA into the cradle. Usually the computer didn't recognize it as Pocket PC, so u need to insert the companion CD to ur CDROM. After the computer install the driver, go to folder where ur upgrade file at. Click on HimaUpgradeUt.exe and follow the instruction until finish. DON'T FORGET not to disconnect the power or even take out the XDA headset from the cradle until finish. Good luck guys
i donwloaded something and putted it on my xda II, now it says serial and at the bottom vl.01 i can't use it it's tottaly black no hard reset works, HELP!
euh i really need uyrgent help i can't connect to theactive sync either, i just downloaded the new windows to my device clicked on something and then it went off and only black letters serial and v1.0. it's not my xda so HELP HELP HELP
don't panic...
you are in bootloader mode.
you've probably executed 'enterbl.exe', which is a part of every upgrade.
just connect your device with your pc and run normal upgrade/flash procedure.
buzz
but i can't use active sync anymyore, i unzipped the thing i downloaded and now it got 7 options to choose from but when i click it it opens a install program and in big red letters ROM IMAGE FILE NOT FOUND
it also says
the pocket pc software update cannot locate the ROM image file to update to your pocket pc. Download the correct rom update for your pocket pc and try again and i am a real noob in these thing
did you try a hard reset?
press the on/off button and the softreset button at the same time.
if that wont work
http://forum.xda-developers.com/viewtopic.php?t=18287
try putting that rom on your phone and dont forget to change the country id as described.
good luck friend!
how can i change my country when i have a blanc screen on my pda? and what of the four should i download, i don't speak english so it's double hard to understand
bram said:
how can i change my country when i have a blanc screen on my pda? and what of the four should i download, i don't speak english so it's double hard to understand
Click to expand...
Click to collapse
if you understand my english thats ok.
i completly understand german but im not so good in speaking it.
normaly we can only speak english here but we can make an exeption so you can speak german to me and i will speak english back. OK? or try the translator (www.freetranslation.com)
did you perform the hardreset?
activesync won't work aslong as serial is replaced by the word usb when in the cradle it's ok carry on with the upgrade
try another pc to upgrade!
thats happen to me too.. but...
i also try to install the downloaded items from this website (which is the new windows version 2003 SE), and soon after i start installing it, my desktop computer says "error has occure during the installation process".
:shock: i was very shocked when i see my device completely blank with a word says "USB (on the top)" and "Ver. 1.03 (on the bottom)".. i really panic beacuse my active sync doesn't worked.. but then i start to hard reset my xda then reconnect my device and try to install it several times (bercause sometimes the error message still appear..) after waiting for 5 step of installation which takes abaout 2 hours
tadaaaaaaa now i have an XDA IIs application on my phone...
So in conclusion:
1. do't be panic :wink:
2. try to hard reset ur device
3. reconnect ur device (even if the activesync won't recognized ur device)
4. Install the downloaded files..
5. wait until ur computer says "deleting extended rom" (or something like that)
6. be patient..
7. Pray to GOD..
8. and here you go you got new look for ur beloved xda.
good luck..
oh it works!!!!
there are no words for it and the landscape and the themes, it's BEAUTIFULL!! thanks alot everyone!!!!!!
Similar but not same
Hi I have a similar problem.
While updating my Himalaya device to the XDA2jojo v3.2z5 (not the first time I have installed this version) it has gone completely blackscreen.
I have tried to soft, hard reboot the device. I have also tried to initiate a reinstall with connection error failure. I have tested the batttery and it is okay. No matter what I do I cannot get the device to come back to life.
If I plug the device into the cradle or attach power I get a red light where there is normally the green flashing or orange power light.
Anyone any ideas what this could be.
I have had a similar issue where I would get a blackscreen this problem has occured a few times but I have always managed to get the device back with hard reset.
Similar but not same
Hi I have a similar problem.
While updating my Himalaya device to the XDA2jojo v3.2z5 (not the first time I have installed this version) it has gone completely blackscreen.
I have tried to soft, hard reboot the device. I have also tried to initiate a reinstall with connection error failure. I have tested the batttery and it is okay. No matter what I do I cannot get the device to come back to life.
If I plug the device into the cradle or attach power I get a red light where there is normally the green flashing or orange power light.
Anyone any ideas what this could be.
I have had a similar issue where I would get a blackscreen this problem has occured a few times but I have always managed to get the device back with hard reset.
pleeeeeaaase read/search the forum i know its fustrating when your phone apears to be dead but there are about 100000 topics about this problem and about 100000 times the solution!
greetings OMEGA_ReD
Guys,
I have been trying to find solution on forum, but it seems it will not be so easy ... My MDA1 shows only Wilkommen bei TMobile and soft version G32S54, R3.23.00, 3.16.45 and that is all It does not response on power or anything - it simply shows me Wilkommen or not (if power is unplugged and battery empty). You may see how it looks here: http://www.jester.it.pl/mda/MDA1.jpg I have only USB cable - so if there is any chance to solve this problem having only this cable - please show me the way.
What is the most important - my Active Sync does not see connection ((
Help ...
TIA
B
I think your ROM is corrupt. Try reflashing.
Instructions can be found here:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
Stefan
Hi there,
Thanks for your help - right now I need to find appriopiate ROM Image and it should work...
BR,
B
It seems that I do not have ROM file ;((( and one I found does not work....
Any suggestions?
I will try to cook sth. and let you know
a problem I had
When I first tried to image my device, the usb flash mode using XDA tools didn't work. I think this was because I was using windows vista. Anyway this forced me to use the direct sd flash method, and thus I didn't get the instructions to cold reset my device after the flash, which does seem to make a difference. Have you tried that?
<edit>What do you mean it does not work? What happened exactly when you tried?</edit>
OK - first time did not work, because Hard reset did not worked My mistake ... after reset it seems fine - I made some cooking and I have nice ROM right now but... After another reset and after second upload Boot appears and Wallaby starts making tests. After last test made Diagnostics screen appears and to be honest I do not know what to do Hard reset just shuts down MDA and I cannot switch it on - I can start from the same begining - tests etc. I know I am really close to solve that ... and we will see.
Guys, thanks for your help
Hi everyone.
I'm not in panic, but i'm close to it.
After hardspl done, i flash to Shadow 2.0 and everything goes ok.
Then, it stuck at bootloader! Softreset, hardreset, nothing helps, and worst, i can't connect to pc with usb!! simply can't connect!!!
I've done everything i can. search a lot, read a lot, and nothings help!!
so, please help me!!
(sorry my bad english)
is your battery more fully charged? (or at least 50%)
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
mc_falco said:
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
Click to expand...
Click to collapse
Try connecting the usb and running aku 2.2 WM5. That worked for me before other times.
I Am Not Pretty Sure But It Might Help U Out!
mc_falco said:
yes, it's almost full (80-90%).
i tried to pull it out a lot of times, waiting 20s, 2 minutes, half an hour, and nothing..
I really don't know what to do
Click to expand...
Click to collapse
why not try to do old way of flashing and it might help coz'
it help me when i had bootloder stuck.
i try with Prophet_PV_Temp. rom
and it went everything good .
thanks
Take off battery and place it back, switch on. What happens?
Regards,
Carty..
First thing to try: search and read WIKI:
http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
Perhaps the links to the AKU/NVID are dead, I didn't check, but you can use any official ROM to get your phone back.
You MUST disable the 'connect through usb' option in AS before it will work.
Please Help I Have Done Everything But Cannot Get My Prophet To Connect Via Usb.
I TRIED EVERYTHING. I have bootloader screen but when i connect through USB it just says that device not recognized and nothing would happen. I even took the battery out for 2 hours... put in another phone charged to maximum and still same problem. Please if anyone could help.. i love this phone cant let it die like that.
I have ni ideas other than that you are doing something wrong...
l3v5y said:
I have ni ideas other than that you are doing something wrong...
Click to expand...
Click to collapse
Well I used the upgrade guide and i have done upgrades before and everything went fine. Except today when i tried the new way and tried to load the New Shadow Rom. all was done ok but when the phone restarted it just stucks at the bootloader. and since then it wont connect through USB . the PDA wont get recognized at all.. any ideas?
Use the 'old' upgrade method, and recover using an official wm5 rom from the ftp server. you must disable connect through usb in active sync... see the wiki for more details (prophet recovery)
please go to the link in my
signature...
Should Help!
I've bricked my S200 after an error in uploading 4.0.0.6 and after going thru the wiki steps... it's working again
After ROM upload my HTC Hero show only some logo like device out of box. Nothing else is going. Button combinations for bootloader access is not working. Any ideas?
I managed to skilfully brick mine too, is a there a way to get it to boot up via key combination or using USB from a computer?
We are three now.
I know (presumably) my error: I flashed an SPL zip package that could be of the wrong type (Dream).
The boot shows the phone logo (mine says G2 T-Mobile).
The home keydown at boot doesn't work.
Is there a possibility to unbrick it?
Hope someone tells you how to unbrick it as I was about to do the update the ROM, not sure I want to do it now.
Right this is very weird as i had the same picture on my phone and thought it was bricked too..
BUT i just did a soft reset call menu end together. Then i did a hard reset as i wasnt sure if the soft one had done anything. Battery out then in and start up phone whilst holding down house and back key and then it started to boot up. So not sure if this helps anyone i doubt it as its very random but i thought id share just in case!!!
I had just flashed my radio when mine did this..
friend of mine had tha problem too, he had to send his device to htc.. 50 bucks ;-)
hmmm ... i am one of u guys now ...
no matter what key-combo i press, it just show a BOX and an arrow and a phone ... 3 sec later, phone turns off, no matter hwat key u press, it is not doing anything until u unplug the batery ... then when u turn it on, it repeat the same thing again
check if you can access fastboot via back+power when the phone is off. if so install recovery image and then install correct rom. if not i guess you're screwed, not sure though.
This guy
http://forum.xda-developers.com/showthread.php?t=556038
seemed to have the same issue and resolved it.
Hope it helps/good luck!
sonatbey said:
i bricked very bad no screen no logo not booting. anyway any helps
Click to expand...
Click to collapse
Please be more explicit as to what exactly you did.
(for someone to help you)