when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
johnjohn1977 said:
when i power on my atom,
it only flash the orange led and never work anymore,
even if i reset or push the power button,
it happens nothing.
the only way make me think it's not a brick is to replace the battery,,
keep holding reset and center button then put the battery on and off many times,
then i put the battery on and release all buttons,
it goes into the bootloader,
then i connect atom with usb cable,
my computer shows unknown device.
Click to expand...
Click to collapse
read the wiki...
Did you Flash a new ROM?
Regards,
Carty..
Carty said:
Did you Flash a new ROM?
Regards,
Carty..
Click to expand...
Click to collapse
yes
i flash a wm6 rom without reading the attention carefully
use spritebackup
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
2234jones said:
Hi there,
If you plug the carger in and the red light shows, then it's charging. If this is the case you may be able to put it into bootloader and try again, but with proper rom.
hope this helps
Click to expand...
Click to collapse
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
johnjohn1977 said:
i can't flash my device with any rom
the bootloader seems have some problem
i can't use camera+reset to change into bootloader mode
Click to expand...
Click to collapse
remove your battery about 1-2 minutes and plug in back, after that try to press camera + reset.
Related
PLEASE SOMEBODY HELP ME
TWO WEEK AGO MY ATOM WAS DEAD
IAM HAVE BEEN TRY TO HARD RESET ALSO MN1 BOOT LOADER ( POWER BUTTON+CAMERA BUTTON). BUT DOESN'T WORK.
SO TODAY IAM TRY TO FLASH BOOT LOADER FROM JTAG PORT, AFTER FINISH FLASH PROGRAMED MY ATOM STILL DEAD.
SOMEBODY PLEASE HELP...
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Aegishua said:
Okay, firstly dont put everything in caps.. its EXTREMELY annoying. Secondly, the device turns on correct? if it does then just try flashing from either your PC through Activesync OR via a memory card with a ROM on it. Consider using a stable ROM from either a ROM Chef or the O2/MWG website.
Click to expand...
Click to collapse
Haii.. thank you for your respon soon.
for your information my PDA totaly malfuction. that no respon when iam press power buton+camera buttonto go to MN1 boot loader .
only red lamp on when the PDA connect with charger battery.
Hmm okay.. so that means it still charges. You should try charging it for an extended period of time and then turning the device on. If the device comes up with the Manufacturer logo then you should just soft reset it and hold down your bootloader combination and go from there. However, if it doesnt even come up with the Manufacturer logo then you should consider getting it repaired.
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Atom Brick Solution...
suga_ngr said:
Hii...i was do to charge my PDA also iam test with volt meter that battery is full power 4,2 volt dc.
So i try to push power button than my PDA doesn't start till now....
Click to expand...
Click to collapse
Have you search on wiki?
I've been through that condition, last night actually when I pressed the wrong button (Power Button) when the MN1 bootloader looked for diskimg.nb0.
My device was near to death. I couldn't find the MN1 bootloader on my device's screen when I pressed the CAMERA+RESET(stylus). It remains dead until :
-I search the solution on http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK, I could see my device running its MN1 Bootloader
and looked for the ROM (diskimg.nb0) again and continued the ROM installation process
How to get the diskimg.nb0 please read this page :
http://wiki.xda-developers.com/index.php?pagename=ATOM_SDCARD
Maybe atom pure had the same step with atom exec when we try to solve the Brick Problem.
Cheers...
TOM PURE Dead
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
try th!s tr!ck (cb ini mas)
yesterday 09 jan 10 it's happened same to me.
my case is downgrade from h3llow0rd1 6.1 to PD4v!et 19971 by m3dk!d.
then atom hang up.. dead! no screen, cann't boot or ON.. but still can charging
This tr!ck may be this could help u..
1. charging, look red lamp is on
2. then try replace battery, then put back on. it will blink (button call and end call will blinK)
3. with stylus try reset with pressing record button
4. if your lucky then it will show you boot loader screen
Now my atom is back again using Hell0w0rd R0M ... (^_^)
suga_ngr said:
With my experience my atom was hardware broken.
somebody please tell me where i can buy atom hardware cause iam very love my atom...
Click to expand...
Click to collapse
Entering BootLoader Mode:
1.Remove Battery
2.Press Camera button and hold it while insert the battery.
3.Press Reset with stylus (keep holding camera button)
If you're lucky, you'll be directed to bootloader mode.
try to push the power & camera button together while inserting the battery and then enter the bootloader mode camera+reset button.
My Atom Life (was) dead, too
..but only for awhile
this happened when I tried to flash this Bajok ROM.
I'm not new to flashing, but that kinda make me 'a little' careless this time.
I transferred the .dio file using active sync explorer while doing other stuff with my laptop.. soon after, I see that the file transfer is done, cause the window is closed. As usual, I do the rec button + reset ritual and flashed away..
I again continued my other works and got mesmerized in it for a moment or two.
Half an hour later I realized that my atom has been showing bootscreen for quite some time..
My first failed flash! Well, I thought, this is it...
Just to make sure, I pulled out the battery, put it back again and reboot.. still the same stuckness... Then, I figured that since this was caused by ROm flashing failure, why dont check the .dio file? So I did. I pulled out the memory card, put it in a card reader and explore it.. I notice that the .dio file is only 18 megs.. whatta..? The original .dio is like 70 megs, so it must had been transferred it incomplete.
So with high hope, I retrasferred the file, this time completely.
I inserted again the battery and repeated the rec button + reset ritual..
Boot loader appeared and flashed away like a charm!
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/showpost.php?p=6707785&postcount=1 )...but[/url] with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india...
gdsbalaji said:
Hi guys, i am facing exact same thing which dannytgt faced (http://forum.xda-developers.com/show...count=1)...but with no luck what so ever.....was running a stock rom in my hd2 3.14....wanted to try wp7 and did a task29....after that...hd2 doesnt go into bootloader screen....tried all possible combinations with/without sd,sim, holding vol down, vol up, both with power tapped...power holded etc etc...hd2 always goes into stick together screen and doesnt progress as there is os to load....opened up the mobile and tried with a pin to push the vol down switch directly also....all hardware keys were working gr8 (including vol down and up and power keys) whn win 6.5/android was running.
i know for the fact that this is reversable....if only my hd2 can get to bootloader...i will hv os running in a jiffy....
any ideas ppl? my hd2 is 3 months old ...no warrenty cos i bought it in US and using it in india...
Click to expand...
Click to collapse
Wow, did you search? There is a thread right below yours with 13 comments for the same problem.
i did search for 2 days and tried the suggesting provided by the users...but nothing seem to work....i just need to get to the bootloader so that i can load a rom and move on to wp7....after task29...somehow hd2 never goes into bootloader screen...tried many times hoping for luck...still trying...
bootloader dont load
some more details...tried to task29 (doloop) with 100% success and then my tmo hd2 wont go into bootscreen what ever i do...its stuck for ever in "stick together"...i know there is no os to load...but i dont understand y cant my hd2 go intobootloader
so far i tried
with holding volume down and power key with a single tap
with holding volume down and holding power key
with holding volume down, volume up and power key with a single tap
with holding volume down and reset button
with/without sim
with/without SD
with/without plug in wall charger
with/without plug to pc via usb cable
observations...when i pull out the battery and put it back in and then connect to computer when the phone is still off....the charging indicator LED glows in orange.
when in this mode if i switch the phone on with power/end key....it doent start...i have to pull the usb out, the orange LED still glows...and if i tap the power/end key nothing happenes...i have to pullout the battery to get it to start and eventually get stuck in "stick together"..
would really appriciate if any1 can help me get my hd2 into bootloader screen...
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
gdsbalaji said:
resolved the problem myself.....hd2 is working like a charm....thanks for all your support.
Click to expand...
Click to collapse
hey. how did you fix it?
mine is totally dead after flashing a non compatible rom, but i can revive it if I can go to bootloader
hanniabdin said:
hey. how did you fix it?
mine is totally dead after flashing a non compatible rom, but i can revive it if I can go to bootloader
Click to expand...
Click to collapse
With some more information, it was easily'r to help you.
Witch HD2 device do you have?
Witch stock ROM did you install?
Can you get access to bootloader?
SOLVED {bootloader dont load}
posted my the solution to my problem here.
http://forum.xda-developers.com/showpost.php?p=10644926&postcount=4
check it out...
________________________
thank me if this is useful.
kurt-willems said:
With some more information, it was easily'r to help you.
Witch HD2 device do you have?
Witch stock ROM did you install?
Can you get access to bootloader?
Click to expand...
Click to collapse
mine is t mobile hd2
I installed rom 2.01
I cann't got to bootloader and I can't eveing sync it with the windows. the windows just give sound but no sync. even the charging light will not turn on.
How can I remove the battery and do a "force boot"? The phone is stuck on the recovery screen. I'm unable to restart/boot.
I think the only way it's to remove the battery.
Can someone helpme? the battery appears to be glued to the phone.
Thanks
Update:
I was able to execute the recovery and restore my backup. But after that the phone turned off, now It does not turn on at all.
I'm trying the power + volume up. The phone respond with the first vibration, then the next three, then, nothing happens.
The phone does not connect on the PC. There's no connection. It's not recognized by flashtool. I'm unable to update, change roms, I need to at least connect it.
if I plug the usb cable the red light appears and keep blinking slowly...
Press and hold power button and + volume button until it restarts.
neectron said:
Press and hold power button and + volume button until it restarts.
Click to expand...
Click to collapse
Worked. Thanks
But, there's no way to remove the battery? Impressive. I almost broke the phone trying.
saulob said:
Worked. Thanks
But, there's no way to remove the battery? Impressive. I almost broke the phone trying.
Click to expand...
Click to collapse
You may have to disassemble your phone to remove the battery.I don't recommend it.
My God.
Now it broke for good.
Everything was fine. I was able to make it restart pressing power + volume up.
Then I entered the munjeni recovery again, restored the yesterday backup, the phone booted. And then no show, no image, nothing, nada.
I'm trying the power + volume up. The phone respond with the first vibration, then the next three, then, nothing happens.
Help!!!!
Flash stock ftf.
neectron said:
Flash stock ftf.
Click to expand...
Click to collapse
How can I do it? The phone does not connect on the PC. There's no connection. It's not recognized by flashtool.
Btw, if I plug the usb cable the red light appears and keep blinking slowly...
saulob said:
How can I do it? The phone does not connect on the PC. There's no connection. It's not recognized by flashtool.
Btw, if I plug the usb cable the red light appears and keep blinking slowly...
Click to expand...
Click to collapse
Download ftf for ur phone
Start flashtool
Click thunder icon
Select flashmode
Selecy ftf and let flashtool prepare the files for flashing
It will ask u to connect ur phone
Now attach ur phone to usb keeping the volume down button pressed
This should work
drsanket_xperia_u said:
Download ftf for ur phone
Start flashtool
Click thunder icon
Select flashmode
Selecy ftf and let flashtool prepare the files for flashing
It will ask u to connect ur phone
Now attach ur phone to usb keeping the volume down button pressed
This should work
Click to expand...
Click to collapse
Worked, thanks.
I was able to flash it and boot. Thanks
saulob said:
Worked. Thanks
But, there's no way to remove the battery? Impressive. I almost broke the phone trying.
Click to expand...
Click to collapse
Bro, Sola has non removable battery. You cant remove it.
mirost1 said:
Bro, Sola has non removable battery. You cant remove it.
Click to expand...
Click to collapse
That's new to me. Thanks.
saulob said:
That's new to me. Thanks.
Click to expand...
Click to collapse
No prob buddy, enjoy your phone and be careful what you do. :good:
Hello, guys
I upgraded my z2 from 5.1.1 to MM. It's existenz v1.0.0. It worked good. I wanted to downgrade to Lollipop 5.1.1 . I entered TWRP and restored the ROM that I saved before. I press "reboot system" and then It totally backed out. It can not turn on. I pressed power + volume up, it didn't vibrate. I tried, tried... many times but it didn't work. I use the flashtool to downgrade. When I pluged the cable and pressed volume down. The red light just flashed, flashed and flashed and nothing happened. What is that problem. Can I save my phone anymore. Plz help.
Sudden death.
con_cop said:
Hello, guys
I upgraded my z2 from 5.1.1 to MM. It's existenz v1.0.0. It worked good. I wanted to downgrade to Lollipop 5.1.1 . I entered TWRP and restored the ROM that I saved before. I press "reboot system" and then It totally backed out. It can not turn on. I pressed power + volume up, it didn't vibrate. I tried, tried... many times but it didn't work. I use the flashtool to downgrade. When I pluged the cable and pressed volume down. The red light just flashed, flashed and flashed and nothing happened. What is that problem. Can I save my phone anymore. Plz help.
Click to expand...
Click to collapse
Have you tried pushing the red button for 5 seconds under the microusb cover flap to completely reset the system?
Does the device get recognised in the DeviceManager, if so have you installed the correct developer.sonymobile[com]/downloads/drivers/xperia-z2-driver/ drivers for it? (you could also try it on ubuntu)
Are you sure your connection / cable is good?
Have you tried to boot into theandroidsoul[com]/sony-xperia-z2-flash-mode-54084 flashmode? (volume down), does it get recognised then?
desireholic said:
Have you tried pushing the red button for 5 seconds under the microusb cover flap to completely reset the system?
Does the device get recognised in the DeviceManager, if so have you installed the correct developer.sonymobile[com]/downloads/drivers/xperia-z2-driver/ drivers for it? (you could also try it on ubuntu)
Are you sure your connection / cable is good?
Have you tried to boot into theandroidsoul[com]/sony-xperia-z2-flash-mode-54084 flashmode? (volume down), does it get recognised then?
Click to expand...
Click to collapse
I tried the ways you showed me. Sadly, it didn't work. The cable I use is OEM. I connected it in flashmode to flash. It didn't recognize. The red light of the phone kept flashing. Maybe, my phone is completely dead. Thank you for helping me.
con_cop said:
I tried the ways you showed me. Sadly, it didn't work. The cable I use is OEM. I connected it in flashmode to flash. It didn't recognize. The red light of the phone kept flashing. Maybe, my phone is completely dead. Thank you for helping me.
Click to expand...
Click to collapse
Ah, this doesn't sound too good. The good thing is that the flashtool works, but since it doesn't help you may try a method called "test point". But if you decide to do it, be very careful not to touch anything else with the paper clip (if you touch the small component with the metal surface there will be sparks coming out).
Sent from my Redmi Note 3 using XDA-Developers mobile app
have you tried to put your phone on charge?
sounds to me that the battery level is too low.
are you on LB or UB??
michel090428 said:
have you tried to put your phone on charge?
sounds to me that the battery level is too low.
are you on LB or UB??
Click to expand...
Click to collapse
My phone is LB. The battery was about 60% plus at the time of restoring the LP Rom. I pluged it in to charge, but the red light kept flashing.
so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
kuhaku319 said:
so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
Click to expand...
Click to collapse
If there is no other way you can always open the phone and charge the battery manually(if you have the equipment to do that). I had to do that to my phone yesterday(my battery was so low that it wouldn't boot).
BlAckXpeRia said:
If there is no other way you can always open the phone and charge the battery manually(if you have the equipment to do that). I had to do that to my phone yesterday(my battery was so low that it wouldn't boot).
Click to expand...
Click to collapse
how can i remove the case to get the battery out of the phone? its not removable right?
uh. no one?
kuhaku319 said:
how can i remove the case to get the battery out of the phone? its not removable right?
Click to expand...
Click to collapse
You have to use a hairdryer. There are tutorials on YouTube.
kuhaku319 said:
so i was flashing existenz MM and i can't go to recovery mode, before installing it i have xzdual recovery installed, so i thought i can just flash it again (and ofc it was stupid because after that i just know xzdual won't work with MM) so it's bootloop even when i charge it, the problem is the battery died and it won't fill the battery, the phone keep restarting when plugged in with charger so it keeps draining the battery before it filled up, i can't flash it because of that, the question is, how can i fill the battery so that i can flash it using flashtool?
thanks, and sorry if my English is bad.
Click to expand...
Click to collapse
The phone should also be able to charge in recovery. Try that.
Btw. I recently flashed a Z2 via flashtool with an unplugged battery (usb power was enough), so you could also try flashing it now although it's empty.
Sent from Note 3, Xiaomi Redmi Note 3.
mr.loverlover said:
You have to use a hairdryer. There are tutorials on YouTube.
The phone should also be able to charge in recovery. Try that.
Btw. I recently flashed a Z2 via flashtool with an unplugged battery (usb power was enough), so you could also try flashing it now although it's empty.
Sent from Note 3, Xiaomi Redmi Note 3.
Click to expand...
Click to collapse
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
kuhaku319 said:
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
Click to expand...
Click to collapse
I would first try to flash just like it is now, without opening the back cover.
Opening the back panel is the last option I would consider, but only if everything else fails.
The thing with opening back cover is, that you will most likely damage you back panel, and you will have to order some new, fake raplecement + the phone won't be waterproof anymore.
And if you can get your phone into fastboot mode (and you've got unlocked bootloader) then just use "adb fastboot flash boot boot.img" command to flash some kernel with recovery.
Sent from Note 3, Xiaomi Redmi Note 3.
kuhaku319 said:
Thank you for the reply,
but the phone cant boot to recovery.
so i should remove the battery and try to flash it without battery plugged in?
because i tried to charge the phone overnight with no luck, havent tried removing the case yet because im not experienced to remove them, is there any alternative that i should try without touching the hardware stuff?
Click to expand...
Click to collapse
Have you tryied to plug it in and then press power and volume up continiusly until you fell three vibrations? i think this is for reseting the phone if you continue to press until another vibration it will shut down and maybe then it will charge. Also this thread had helped me before http://forum.xda-developers.com/showthread.php?t=1849170
NatNikos said:
Have you tryied to plug it in and then press power and volume up continiusly until you fell three vibrations? i think this is for reseting the phone if you continue to press until another vibration it will shut down and maybe then it will charge. Also this thread had helped me before http://forum.xda-developers.com/showthread.php?t=1849170
Click to expand...
Click to collapse
Thanks you for the reply
i tried the vol up + power only one time until it vibrates 3 times for the first time and its off, but when i plugged the charger its continues on bootloop cycles thus battery not filling up.
i guess im gonna try until another vibration and see what happen.
and thank you for the link, im gonna give it a try too later, im not home right now, cheers.
kuhaku319 said:
Thanks you for the reply
i tried the vol up + power only one time until it vibrates 3 times for the first time and its off, but when i plugged the charger its continues on bootloop cycles thus battery not filling up.
i guess im gonna try until another vibration and see what happen.
and thank you for the link, im gonna give it a try too later, im not home right now, cheers.
Click to expand...
Click to collapse
Maybe you should try it while plugged in also.
mr.loverlover said:
I would first try to flash just like it is now, without opening the back cover.
Opening the back panel is the last option I would consider, but only if everything else fails.
The thing with opening back cover is, that you will most likely damage you back panel, and you will have to order some new, fake raplecement + the phone won't be waterproof anymore.
And if you can get your phone into fastboot mode (and you've got unlocked bootloader) then just use "adb fastboot flash boot boot.img" command to flash some kernel with recovery.
Sent from Note 3, Xiaomi Redmi Note 3.
Click to expand...
Click to collapse
yeah i tried flashing it but the phone is totally dead, pc wont detect the phone because the phone is dead. that's the issue im facing now :silly:
NatNikos said:
Maybe you should try it while plugged in also.
Click to expand...
Click to collapse
tried, still bootlooped, when i hold power + vol up while plugged in, its powered on again and started bootlooping again
im just wondering. did u use flashtool to flash the ftf again?
Dilesh Perera said:
im just wondering. did u use flashtool to flash the ftf again?
Click to expand...
Click to collapse
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
kuhaku319 said:
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
Click to expand...
Click to collapse
ok try like this
1 put phone off ( u can press the little red button inside the left side flap till it vibrate 3 times )
2 disconnect the cable from Pc
3 open flashtool and select FLASHMODE select the ftf u going to flash
4 once the flashtool request to connect the phone connect the phone while keep on pressing the vol button
it should flash the ftf
kuhaku319 said:
yes, im using flashtool, but when i plug the phone in fastboot mode, flashtool doesnt detect the phone because phone died, no battery.
if i plug the phone in fastboot (hold vol down & plug the usb) will it charge?
Click to expand...
Click to collapse
It won't probably charge in fastboot/flashmode.
But it's very strange that the PC won't detect your phone when trying to enter flashmode.
Because, as I said earlier, I was able to get Z2 into flashmode without any power (battery taken out).
There should be some change in device manager when you connect the device.
Are you sure all the drivers are installed on your PC?
Dilesh Perera said:
ok try like this
1 put phone off ( u can press the little red button inside the left side flap till it vibrate 3 times )
2 disconnect the cable from Pc
3 open flashtool and select FLASHMODE select the ftf u going to flash
4 once the flashtool request to connect the phone connect the phone while keep on pressing the vol button
it should flash the ftf
Click to expand...
Click to collapse
mr.loverlover said:
It won't probably charge in fastboot/flashmode.
But it's very strange that the PC won't detect your phone when trying to enter flashmode.
Because, as I said earlier, I was able to get Z2 into flashmode without any power (battery taken out).
There should be some change in device manager when you connect the device.
Are you sure all the drivers are installed on your PC?
Click to expand...
Click to collapse
Solved
Apparently the driver is acting weird, but i uninstalled all z2 driver and reinstall them, all working and can be flashed
Thank you guys for helping me :fingers-crossed::highfive: