I have QPST 2.7 build 247 and an HTC PPC 6800
I cant get it to connect to QPST
I put it in DIAG mode (##3424) a screen saying DMR v 1.65 pops up
Ok then Windows recognizes a new hardware tries to install a driver for "Generic Serial" and cant find one. Does anybody have the driver for it so I can get it connected?????
here ya go. i know the drivers u need r in there somewhere
http://rs319gc.rapidshare.com/files/97878673/TITAN_USB_drvs.rar
anyways
I got it working with these Drivers
included the HTC Diagnostic Interface Drivers, and USB Modem drivers for the Titan
just thought i post this in case somebody else having the same problems
http://www.vzam.net/uploadedfiles/WModemDriverInstaller.exe
QPST 2.7 Build 247 For Nike Works For Titan?
Quick question as stated above "Does the QPST for Nike Work For Titan as well?" Thank you
Please, help
I can't get Mogul to connect to PC in DIAG mode (##3424#)
I put it in DIAG mode (##3424#) a screen saying DMR v 1.87 pops up. Then I connect it to PC, but PC don't see Mogul as hardware. In ActiveSYNC mode I connect Mogul with no problem. A few weeks ago everything was Ok. I was able to connect it in DIAG mode and work with QPST
I got my ppc6800 to go into programming mode with the ##3424 once. I was able to use QPST and look at the settings and such. I disconnected, rebooted the phone, and wanted to do it again and now the phone dials ##3424 instead of opening the DMR program.
Anyone else have this issue or experience this?
edit: got it working. found my problem.
mrslysly said:
I got my ppc6800 to go into programming mode with the ##3424 once. I was able to use QPST and look at the settings and such. I disconnected, rebooted the phone, and wanted to do it again and now the phone dials ##3424 instead of opening the DMR program.
Anyone else have this issue or experience this?
edit: got it working. found my problem.
Click to expand...
Click to collapse
What was your problem? My phone just dials ##3424 every time. I have the correct carrier cab installed.
sharper4 said:
What was your problem? My phone just dials ##3424 every time. I have the correct carrier cab installed.
Click to expand...
Click to collapse
If you are sprint.... try ##3424#
sharper4 said:
What was your problem? My phone just dials ##3424 every time. I have the correct carrier cab installed.
Click to expand...
Click to collapse
FIXED:
I had a 3rd party dialer installed. Once I removed it, the codes all worked correctly.
sharper4 said:
FIXED:
I had a 3rd party dialer installed. Once I removed it, the codes all worked correctly.
Click to expand...
Click to collapse
If you use a 3rd party dialer. Install it. Then re-run the carrier cab. As I posted in the other thread, there are registry keys that hold the values for these codes. I'm curious as to if the new dialer either doesn't read this key, or if it overwrites them. Worth the try.
Related
So I'm a total n00b at unlocking phones but I was trying to unlock my alltel 6800 and after running the program and following the steps I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc. I tried a hard boot/soft etc. and can't find a solution. Also activesync is not recoginizing it. Thanks much for any help.
i believe you have to flash it with a new rom/radio.
download the the newest radio. connect your phone via usb. your screen should be in the tricolor (2.40spl) at this point. run the radio flash.
Download a new rom. do the same as above.
to get to tricolor screen (hold power + camera + press soft reset)
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
=I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc.
Click to expand...
Click to collapse
it IS recognizing the phone being plugged in if it says USB at the bottom, so just flash a new rom/radio and you should be good.
HOLD, Give a little more info please
wilmheath said:
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
Click to expand...
Click to collapse
OK, before it is bricked, tell us the numbers on the rainbow screen, then if it is 1.6 then run the 2.40 olipro, then new ROM, then radio. It is not broken yet, activesync does not like it when the unit is in bootloader mode so it will not show it, but the RUU will work if you just go forward with it and when done it will get you out of bootloader. If you get confused and lost then being an alltel unit you can put the 1.6 bootloader back on, run the stock RUU from utstar.com, bring it back stock and start again.
I got it fixed and installed the sprint firmware but silly me let it run through the setup and now it's trying to use the spring network. Sometimes I wish i could punch myself in the face..
Ok so i got no2chem up and running great but I still can't actually dial out. When i dial it says i'm not allowed to etc after a few rings. Is there some way to change back to the alltel network?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
First of all, you don't relock your phone...you leave 2.4-olipro on it because it's required to boot your phone with this rom on it.
Second, go into activesync settings and make sure usb is enabled in the connections.
get back to Alltel,,,,
wilmheath said:
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
You will need to load up the PRL and then do IOTA.
madman34 said:
You will need to load up the PRL and then do IOTA.
Click to expand...
Click to collapse
I'm sorry but i'm not familiar with those terms. I do have USB enabled on activesync though but it never detects it.
From reading other threads I assumed I had to relock it, then reload the alltel rom to get the radio working again. Is there another way?
I got the factory alltel rom back in and working but it's not letting me make calls still. Any ideas on how to fix this?
Well i got my phone working finally but now the data line is not working. It says I need a password now which I haven't needed before.
Ok so I am trying to open the GPS on my new phone. I am at the QPST part but I can't add COM4 or COM5 beacuse it says its busy or something? Who can I get it to work?
It also does not show my phone in the service programming section.
Did your phone come with the new update already? Just check and make sure.... Also what rom, spl etc... have you loaded?
My phone came with the original but I had trouble with the Bootloader so I had to flash it with the new ROM but I didn't go through the configuration at the begining of loading the rom. I immediately flashed it to DCD 3.2.6. so Now I have
Radio 3.42.50
ROM DCD 3.2.6
SPL 2.47
ANything else?
This is the error I get from QPST after I go to "Add New Port" ...
"There was an error enabling COM4. The Port may not be working properly or may be busy (-2147467259)"
THe port is not in the port list so I had to put it in manually. It was in QPST before but I removed it and now I can't add it again? What do I do?
JukEboXAuDiO said:
My phone came with the original but I had trouble with the Bootloader so I had to flash it with the new ROM but I didn't go through the configuration at the begining of loading the rom. I immediately flashed it to DCD 3.2.6. so Now I have
Radio 3.42.50
ROM DCD 3.2.6
SPL 2.47
ANything else?
This is the error I get from QPST after I go to "Add New Port" ...
"There was an error enabling COM4. The Port may not be working properly or may be busy (-2147467259)"
THe port is not in the port list so I had to put it in manually. It was in QPST before but I removed it and now I can't add it again? What do I do?
Click to expand...
Click to collapse
Your phone is not connected or you are not running DMR (or whatever). I had this problem when using nueUSB. I had to put it on "dont ask each time I connect" mode and selected to autostart up as ActiveSync. Well thats what was holding me back.
Check deviuce manager in Windows and tell me if the HTC USB Modem shows before you launch QPST but after you put the phone in the Diag Mode.
Oh yeah, you did install the drivers, correct?
Oh and can you get an Active Sync connection before entering the Diag Mode?
Also, I found it handy to reboot after I got those messages, both the phone and the PC. Maybe some sort of hook on the QPST app that wont let it see the new connection until a reboot I was thinking? Possibly locked up the port when trying to connect original. Just theory but thats what worked for me.
mkenny2 said:
Did your phone come with the new update already? Just check and make sure.... Also what rom, spl etc... have you loaded?
Click to expand...
Click to collapse
The new update has nothing to do with QPST. I entered QPST right after flashing to the new Official GPS Rom so i could examine the GPS settings and had no issue at all.
I had the same problem. So, I uninstalled QPST and reinstalled it and it fixed the problem and it worked.. Good luck!
JukEboXAuDiO said:
Ok so I am trying to open the GPS on my new phone. I am at the QPST part but I can't add COM4 or COM5 beacuse it says its busy or something? Who can I get it to work?
Click to expand...
Click to collapse
JukEboXAuDiO said:
Ok so I am trying to open the GPS on my new phone. I am at the QPST part but I can't add COM4 or COM5 beacuse it says its busy or something? Who can I get it to work?
Click to expand...
Click to collapse
You must put your phone in DIAG mode... ##3424... and connect the USB cable... It will "Create" new ports. It won't be the same one that Activesync uses. Open Windows device manager and go to ports. If you unplug and re-plug the cable to the phone and computer... you'll see it disappear and reappear
nitro66215 said:
You must put your phone in DIAG mode... ##3424... and connect the USB cable... It will "Create" new ports. It won't be the same one that Activesync uses. Open Windows device manager and go to ports. If you unplug and re-plug the cable to the phone and computer... you'll see it disappear and reappear
Click to expand...
Click to collapse
Ok so i did that last night and it worked with ports COM6 and COM7. Now I have a problem. i did gc14's GPS fix, did the registry fix, used the certs to disable security and enable it, installed quick GPS and I still can not get a fix with my GARMIN XT program. Any ideas?
JukEboXAuDiO said:
Ok so i did that last night and it worked with ports COM6 and COM7. Now I have a problem. i did gc14's GPS fix, did the registry fix, used the certs to disable security and enable it, installed quick GPS and I still can not get a fix with my GARMIN XT program. Any ideas?
Click to expand...
Click to collapse
did you try GPS Viewer? HERE
I will try it. thanks. Lets hope it works.
Also, make sure Location is set to On and not 911 Only in the phone settings.
Where can I download the agps fix files? The thread that comes up everywhere (http://wiki.xda-developers.com/index.php?pagename=VerizonAGPSFixhas bad links to cinconet.org.
i installed 6.1 rom with 3.37 radio from verizon . then i did unlock with 2.31 coke then flashed nsffans 6.5 rom . now i downloaded wmodem installer and qspt . i put the phone into diag mode and connected to activesync . diag screen goes to today screen and activesync disconnects . then nothing ! when i open add new ports in qspt it shows the two usb comms but when i click them it says busy ! what do i need to do to get the dmr to not switch to today screen
You don't have a HTC titan 6800. You should be posting under your vogue phone category. I have told you before to post the in the other section I don't understand why you don't listen.
Ok, I installed WMDrivers and QPST, and when I put the phone in ##diag, it comes up on COM18. I go into QPST, add port (com18/Unknown, not DIAG label), and the port adds fine, but doesn't see the phone. I have searched around and can't find an answer.. any ideas?
Using the right one???
MetalHd said:
Ok, I installed WMDrivers and QPST, and when I put the phone in ##diag, it comes up on COM18. I go into QPST, add port (com18/Unknown, not DIAG label), and the port adds fine, but doesn't see the phone. I have searched around and can't find an answer.. any ideas?
Click to expand...
Click to collapse
I was having the same problems. be sure that you are using the WMdrivers and the QPST for the titan. I tried using the one for the 6700 and it would not read the phone. PM if you cannot locate it. I think I have it saved somewhere???
MetalHd said:
Ok, I installed WMDrivers and QPST, and when I put the phone in ##diag, it comes up on COM18. I go into QPST, add port (com18/Unknown, not DIAG label), and the port adds fine, but doesn't see the phone. I have searched around and can't find an answer.. any ideas?
Click to expand...
Click to collapse
The problem is in ROM version.
With DCD 3.2.5 QPST works, with 3.3.4 it does not.
I don't know if 3.2.6 is OK.
wanted to fix cellsouth banner w/3.2.6.. wouldn't stay that way would it from .5 to .6??
Once you fix the carrier banner, reflashing the rom should not mess it up again, it's caused by when you flash your radio the first time. Once QPST and EPST has been fixed, any future updates to radio or rom tho should not bother it.
I actually could never get QPST to work with any DCD 3.2.x rom, I always flash back to 3.1.2 make the change, and then flash back forward to his latest.
BTC
FIXED.
Ok, I tried the specific TITAN WM drivers, and still did not see the phone in QPST. So I did an SPB Backup, hit a stock 3.1.2, read fine, made changes, put back the same kitchen'ed rom I had to 3.2.6, and restored, and couldn't be happier.. unless of course USCC went 3G in my area so I had some bandwidth!
Thanks for your inputs!
MetalHd
So you are wil Cellular South? What are you running on your 6800? I want to upgrade mine but have been sceptical that it may not work on our network.
If possible I would like to know what steps you took; did you have to upgrade your radio prior to unlocking and upgrading?
Thanks
MetalHd said:
wanted to fix cellsouth banner w/3.2.6.. wouldn't stay that way would it from .5 to .6??
Click to expand...
Click to collapse
Nope, I am US Cellular on the coast of Maine. PPC 6800 with a dcd 3.2.6 kitchened rom. 25 megs free at fresh boot with one oxios. 16 gig microsdhc. Just had to change the CellSouth banner that is generated from the radio upgrade back to US Cellular. Seems odd to see US Cellular though, cuz I looked at CellSouth for 6 months before I fixed it.
MetalHd said:
Ok, I installed WMDrivers and QPST, and when I put the phone in ##diag, it comes up on COM18. I go into QPST, add port (com18/Unknown, not DIAG label), and the port adds fine, but doesn't see the phone. I have searched around and can't find an answer.. any ideas?
Click to expand...
Click to collapse
What is the version of your QPST
hello i have a htc touch pro of us cellular
and i ont know how to enable tha funtion ##3424# please help
thanks
Tried and Tried and Searched and Searched, and finally ive gotten to the point of giving up, figured i would take a week or so break and try this again. I have tried everything to get qpst working, i have the 6800 Titan (Qwest) Fully flashed to cricket, Im having issues with the Cricket Internet working on the phone, it keeps saying its not on my plan but i know it is. shows up on my bill and im paying for it.. Figured i could call and have them refresh the phone ( assuming the same thing that *228 does ), but the SPC isnt back to 000000 or 333333, its still the original one from Qwest (which i do have ), but somehow i need to get back to 6 0's so i can have cricket update the phone. pix mail works though, and i figure that uses the data connection so web should work as well correct?
Thanks in advance
what are you doing to try qpst? Are you putting the phone in dmrouter?
i am trying to get the SPC number, its not 000000 or 333333 so i cant get in and change the settings over to cricket. its driving me nuts, got a step by step tutorial on it? im about to lose my mind with this thing. the 6800 was no problem, but this one for some unknown reason i cant seem to get. this ones a qwest 6700
I'm new on the forum, very informative but I could'nt find an answer to this situation. I have a HTC Advantage 7500 that originally came with mobile 5 on it and last year I successfully upgraded it to mobile 6. Couple of days ago I wanted to try something new so I upped it to 6.5 via a link on this site somewhere. The rom update went smoothly but I would like to go to 6.1 because for one the micro drive is not seen under the 6.5 that I have plus it has a slow response to screen manuvers and such. Now when I try to install mobile 6 or 6.1 it says please wait while the update takes place but my device restarts and the error #260 box comes up that says the update utility cannot connect to your PDA phone. Please check your USB connection. I would appreciate any help or suggestions. I know maybe I was wrong to try the mobile 6.5 on this. confused:
Since you are able to use 6.5, (it was a spl 3.5 version unless you
had found and used a spl 1.2) your phone should be having spl 3.5.
You need to search and download 6.1 spl 3.5 rom to change it.
Oh...Welcome!!
pdajoy said:
Since you are able to use 6.5, (it was a spl 3.5 version unless you
had found and used a spl 1.2) your phone should be having spl 3.5.
You need to search and download 6.1 spl 3.5 rom to change it.
Oh...Welcome!!
Click to expand...
Click to collapse
Thanks for your reply. I do now have the file 6.1 spl 3.5 but my device on 2 separate computers it just starts the update restarts my 7500 then the error message about USB connection. I didnt get this error the last 2 times I updated my device. Thanks in advance.
Taking it your pc (Windows XP) with anti virus and firewall disable.
Try flash back previous rom and have the device working first before going
any further.
Best to use same usb cable and port from same computer for your flashing. It helps to isolate problems in future.
Ensure device battery charge is above 60%, at least.
Remove SIM and memory cards before flashing.
I am sorry to hear that you're having problems with your device......however, the problem you've mentioned sounds quite familiar to me but I don't remember how I actually got mine fixed.
I have no idea what OS you're using but
try this:
re-installing activesync/device center then put your device in bootload mode (by holding down the camera button...fully....then press the reset button, keep holding camea button until the colored screen comes up. connect your phone to your computer and let it install the usb drivers.
after thats done, unplug, wait....replug and start up acticesync/device center make sure they're connected/synced then try changing the rom again.
hope that helps.
Thank you all so much. I did these things and it still restarts and goes right back in mobile 6.5 giving that same error message #260 box comes up that says the update utility cannot connect to your PDA phone. Please check your USB connection. Can it be a bad usb cable I'm using I wonder? Interesting my SPL version right now is 1.10.
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
lennie said:
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
Click to expand...
Click to collapse
Thanks so much! I will do this. I wonder why I have a spl 1.10? This is confusing with Win Mobile 6.5?
lennie said:
that's the problem...your SPL should be 3.5 if you're on wm6.5. it is interesting that you got that instead of "invalid Model id" error. all in all I think the same method should solve your problem.
do a search for "invalid model id" and check out the post by cmonex she did a great job in creating a salutation. hopefully you had Hard SPLed your phone and that you had a home network that you had connected your phone so you can get back your phone's MAC address.
EDIT:
Also change your USB cable....I don't trust it, it's possible that it could be the problem. however, seen as your SPL isn't what it should be it the cable is not the problem (but change it anyway)
Click to expand...
Click to collapse
I am using a new usb cable and the same thing happens. It says its starting to update the rom then it restarts my 7500 and error 260 comes up saying that it cannot connect to my device check your usb connection. I don't understand...
I have been having problems changing my number on my phone. I am using DCD 3.3.4 and radio 3.42.50. I can not access the page where i can change my number on the phone. I have the number changed on the bell network. When ever i put the code in, ##564848#, the phone starts dialing. If i do ##564848 then it tried to load EPST and closes. I talked to bell IT and they gave me a link to get the factory bell settings rom.
http://www.pcdphones.com/phone_downloads.aspx?bid=76&cid=16&mid=298&carrier=Bell Mobility
I am using the new boot loader 2.47no2chem i believe. If i try to load the rom, will i run into problems? Does anyone know of a better way to change my number? Thanks for any help in advance.
Cheers,
Andrew
AMC_CAN said:
I have been having problems changing my number on my phone. I am using DCD 3.3.4 and radio 3.42.50. I can not access the page where i can change my number on the phone. I have the number changed on the bell network. When ever i put the code in, ##564848#, the phone starts dialing. If i do ##564848 then it tried to load EPST and closes. I talked to bell IT and they gave me a link to get the factory bell settings rom.
http://www.pcdphones.com/phone_downloads.aspx?bid=76&cid=16&mid=298&carrier=Bell Mobility
I am using the new boot loader 2.47no2chem i believe. If i try to load the rom, will i run into problems? Does anyone know of a better way to change my number? Thanks for any help in advance.
Cheers,
Andrew
Click to expand...
Click to collapse
I was just talking about something similar over at geeks.
#codes do not work with some of the dialers.
Do not know if it will work, but find a dialer cab to install and retry. Worth a shot anyway.
I know this one has worked for me. http://forum.xda-developers.com/showthread.php?t=429179
Thanks for the link, ill try it out. They say to uninstall the previous cab how do you do that?
I also been reading around that i need to install a cdma dialer cab, and this might be the problem why i cant get into the EPST page. If anyone has any more ideas let me know.
I installed another dialer cab with no luck. I installed the cab from the link mattsm posted above with no luck. It tries to load the page and then closes. I was thinking, I installed a DCD 3.3.4 rom but was that rom intended for GSM phones or cdma? I think the settings page was removed from the rom. If anyone has any ideas please let me know. I want to install the rom from bell to get factory settings but i have a new boot loader, so will this be a problem? Thanks in advance
Cheers
The only other thing I think you could try is qpst.
It lets you edit the epst settings from your pc.
you will need the qpst program, htc drivers
google the qpst and I will post some drivers you need in this post with an edit.
after you get the drivers intalled and qpst on your pc, You will enter ##3424# on you phone and hook up your usb to phone and it will install the drivers. Let me find the link to qpst help and I will post it as well. I am sorry right now I am busy but will post these before I leave.
You can try my Diagnostic Shortcut CAB located in my HTC unlock directory, you dont even have to soft reset the shortcuts show up in programs/diagnostic folder.
There is also HTC windows drivers, Active sync 4.5, QPST 2.7 build 3.01 works perfect with TITAN, and many other tools. Plus instructions.
http://www.4shared.com/dir/13899878/aef6ea49/HTC_to_Windows_Drivers__Unlock_Tools.html
Start from ground up EPST change your number, MIN, anything you have to change to switch phone numbers. Then double check using PST and correct any settings. Let me know if you still have problems accessing PST with codes or shortcut. I will make you a Bell CAB that will fix your programming codes.
Enjoy!
Thanks alot for the help. I have to head to class right now but i will be back later today and try it out. When you say drivers, which drivers are you referring too? the drivers for my phone on vista? If you post some steps, i would greatly appreciate it. Thanks again.
RyanMogul6800 said:
You can try my Diagnostic Shortcut CAB located in my HTC unlock directory, you dont even have to soft reset the shortcuts show up in programs/diagnostic folder.
There is also HTC windows drivers, Active sync 4.5, QPST 2.7 build 3.01 works perfect with TITAN, and many other tools. Plus instructions.
http://www.4shared.com/dir/13899878/aef6ea49/HTC_to_Windows_Drivers__Unlock_Tools.html
Start from ground up EPST change your number, MIN, anything you have to change to switch phone numbers. Then double check using PST and correct any settings. Let me know if you still have problems accessing PST with codes or shortcut. I will make you a Bell CAB that will fix your programming codes.
Enjoy!
Click to expand...
Click to collapse
thanks, He has the link. Got to go will check back later. Good Luck.
Yes the HTC windows drivers get installed on your PC. Then QPST, then put the phone in Diag Mode, then plug it in with active sync usb connections disabled, then access Service Programming using QPST. The instructions (SPCunlockinstructions.txt) are on my share site, they will at least get you into Service Programming the rest is up to you.
Another thing I found is to disable driver signing in Vista press F8 while booting up and disable driver signing. Also if you do a search on XDA for HTC vista drivers you will find a thread with some drivers and information you can try.
Thanks alot RyanMogul6800. I have downloaded most of the files that you have mentioned. I can't try them out until monday, but ill give them a shot for sure. Thanks again. The Bell cab you mentioned, is that the problem? I can't seem to understand why in the dialer it tries to load the page and then closes as if it was missing. Let me know what you think.
Cheers,
Andrew
Thanks alot Ryan. I used the program and I changed my number with the qpst. It works now!!!
Cheers,
Andrew