Thanks in advance if anyone can come up with something that helps... I can't imagine what that might be though!
This morning I had a stock Mogul... original ROM, no hacks, even had the Sprint S/W on it. It worked fine.
I downloaded the new Sprint ROM 3.35.651.2 and ran it. While running the Mogul rebooted, went to bootloader, then failed. It was then stuck in bootloader mode. I read up and found that a successful flash should bring it out gracefully so didn't troubleshoot much. I tried a couple of times more to no effect. It was still in bootloader mode.
I then downloaded the old 2.17.651.0 ROM from HTC and that wouldn't work either. Still in boot loader mode.
I read somewhere that a guy got the 3.16.651.0 leaked ROM to update even when the others would not. So, I downloaded and tried it. Everything looked good! It was loading the ROM, the bar went across the screen to 100% and then...
nothing. A black screen. Vista loaded some new drivers and seemed to know there was a USB device attached but I couldn't connect to it in any useful way through Explorer and it didn't show up in the Mobile Device Center.
I thought I'd try flashing it again but since the screen was black I was just guessing. I did a hard reset (both soft keys plus soft reset button) and I got nothing... not even the same connection I'd had after the 3.16 update.
Now, I plug in the device and get no USB connect sound or notification in Windows. I get a orange light on the right LED for maybe 15 seconds then it goes out. Other than that one brief LED the thing is a brick as far as I can tell.
Any ideas? I plan on taking it in to Sprint tomorrow and telling them they bricked my phone with their update if I can't figure anything out tonight.
Thanks!
First POSSIBLY legitimate brick story I've seen.
Have you tried holding down power and camera while pressing reset to see if you can get back to bootloader?
Geckotek said:
First POSSIBLY legitimate brick story I've seen.
Have you tried holding down power and camera while pressing reset to see if you can get back to bootloader?
Click to expand...
Click to collapse
Yes.
FYI... I just left the battery out for about 5 minutes (what the heck, worth a try right?) and put it back in. I get no lights, buttons do nothing, soft & hard reset do nothing, forced bootloader does nothing. The only way I can get the phone to do anything is to plug it in to a USB cable. The orange light comes on for about 15 seconds then goes out. The computer never recognized there is a new USB device attached.
I loaded many custom ROMs on my old 6700 and never had a problem. I leave my new 6800 alone and wait for the upgraded stock ROM and look what happens! Guess I shoulda used a custom ROM instead, eh?
lol sounds like a legitimate "brick" to me. Very strange, and congrats on your new mogul paperweight (i also have one that was a victim of water) haha, good for holding things down on the windy days.
Yup, bricked.
Sprint couldn't figure out how to unbrick it and just gave me a new phone. The new one upgraded nicely and now I have GPS!
Everyone enjoy the upgrade!
same problem
no need to retype what you said. i had the EXACT same problem. phone was completely bricked and continued to crash at 11%. I went to my local store (i work for sprint, and i know a smart tech there) and was told it was kaput. Hard reset, tried to reload other roms, the whole 9 yards. It's a goner, and now i have a new mogul in my hand. I'm afraid to try it again. I'm running vista, and im wondering if that's the problem.
Anyone with vista have the same bricking problem? Is it an issue to directly upgrade from factory rom to the 3.35? My old brick had the current 2.17 or whatever... HALP
Vista
The first time I tried the update I connected the Mogul to my Vista Business 64bit Thinkpad T61p.
The second time I tried it (on the new Mogul) was from my Vista Business 32bit desktop (white box).
I don't know if that helps or not. The second time went smoothly.
On another note... an entertaining one... while I was in the Sprint store today waiting for their tech to confirm that the phone was bricked another guy came in with a Mogul and complained of the same thing. I took the last Mogul they had in stock. Poor guy. I hope they get more soon... there are a lot of people who want GPS and are upgrading their phones. That means there are gonna be some more bricks I'd think.
Hey guys Im a noob and im having a bit of problems
Im stuck in the bootloader screen
TITA100 MFG
SPL-2.40 Olipro
CPLD-9
My comp has windows vista premium so instead of activesync i have windows device center 6.1 I have unclicked allow USB connections
but i think my comp doesnt recognize that they the phone is connected at all although i do here the sound that lets me know that a usb device is connected
exitbl.exe doesn't work keeps telling me
cannot open USB port
Please make sure that USB connection in Activesync is disabled
Also make sure that your USB cable is properly connected
if it helps im on a bell phone
Related
I just tried WM2003SE upgrade, but after erasing message, it just gave connection 101 error!
i tried, hard reset, soft, etc, but no lock it just says:
Serial
v 1.01
if i put it in the cradle, it will show "USB" instead of "Serial",
is this dead? i just bought it and like a hero, tried upgrading
It's not dead.
Put it in the cradle and try the upgrade again.
Don't forget to connect the power charger to the cradle for in case the battry is drained during upgrade.
Regards,
Mark
and if that doenst work try to upgrade it on another pc with active sync
Finally, my advice starts to stick!! :lol:
Have you done lots of upgrading on that particular PC? If so, then it's definitely worth trying a diff PC.
Cheers
Ant
It Worked!
Hi, thanks everyone for your replies, i managed to get it working today on a another PC, looks like its time for me to get another laptop, this one is dying.
It worked sometimes, then cuts off in the middle, then stops working, i tried it all night yesterday, though i lost it all, only had about 2 hours sleep because of that but i tried today on another pc, and it worked the first time.
Probably onboard usb is faulty (although it works with my cable modem, external dvd-rw, etc), but it seems to me, the update/upgrade program needs error-free connection and mine might be ill.
anyway, i downloaded the rom from o2 xda website and updated to that(wanted to upgrade to WM2003SE before it went in coma), i cant afford another crisis , i like my xda 2 too much! :wink:
Thanks for your replies, appreciate it 8)
I don't think it's anything wrong with the hardware. My advice would be to ensure you backup any backup files then uninstall ActiveSync, before removing all registry and folder references to it. Then, reinstall and then see how things go from then on. Glad it's working though now!
Cheers
Ant
Backups
Yup, i've done a backup of the ROM and also the Extended Rom, don't know how to backup or where the Radio Stack is, so i'm assuming its in the main Rom.
The reason i think its the hardware fault is because things like cable modem, dvd rewriters, etc work beneath the drivers, and they do all checksums and checking, with Him upgrade program, it uses ActiveSync APIs, so any hic cups in activesync would be passed down to him upgrade, if activesync did proper data checking and resend data (or might be that the bootloader is limited so it might be limited on what it can do) then the errors could be rectified.
These are all my assumptions. thinking out loud.. etc
I tried reinstalling activesync, etc also created new admin user, tried safe mode with networking (without networking gives TCP/IP error message).
All failed.
i wanted to fix it yesterday night with this laptop, and didnt have access to any other computer, so ended up staying up til late and trying all possibilities, but all failed so i gave up and waited for the next day. came back from work and then tried it on another computer and it went smoothly.
Also tried resetting the xda2 many times, taking the battery out, soft hard cold hot yellow green, tried all, but no luck. :roll:
So i assumed it was a hardware fault, or XP sp2 fault (the other one is a desktop with win2k).
anyway i'll be formatting this xp sp2 soon and putting windows 2k, seems more stable, trying to get maximum mileage out of this laptop.
thanks for the tip though.
After i upgraded to this radio i have had interesting problems with my phone. ithought it was bricked and it very well could be. But sometimes it decides it wants to work but after a minute or two it cuts off. when a softreset or hard reset are perfromed i get nothing but a white screen. I can tell it goes thru the whole process bekuzz usually after putting it to sleep a few times i get my regular screen but the radio doesnt seem to be connected. any help would be appreciated. also the buttons on the face of the phone dont seem to work.Thanx
What is "Regular Screen"?
Regular screen means the screen u would normally get after your boot and splash screen. Or better said my today screen. Sometimes i cant get my today screen up. i had BL 1.04 before the upgrade if that matters any
Today screen is very good! your device isn't fully bricked. It may be a bad radio flash or it may be a hardware issue that merely coincided with your radio upgrade. Next time you get a today screen, try to flash one of the other sspl based radio only updates (find in wiki under radio only upgrades). Remember to practice safe flashing techniques!
usb on rear usb port. No usb hubs!
all winapps closed
running winXP Pro
activesync connected
screensaver/sleep mode off (flashing takes 20+ minutes)
i have flashed the 1.27 radio again without having my today screen and that did nothing. It went thru the whole process of flashing and everything but same results, just a white screen when booting up and afterwards. im downloading the 1.34 radio now.
You need to flash the sspl version which requires first being on the Today Screen (not white screen). Tri-color boot screen will show v1.09-Des if you do this.
i guess i will have to wait to see if i get another today screen and hope that it doesnt reset itself
does it matter that i can put my phone to sleep and wake it up over and over, i just keep getting the white screen. bekuzz now i cant seem to get my today screen back anymore
ok i have done what u said and flashed the 1.34 radio and still have the same problem. after the flash i had my today screen for a minute then it reset itself and now is gone and back to the white screen. also when i was on the today screen i didnt have control of the buttons only touch screen.
i think i may have a different problem. it doesnt seem to be resetting itself everytime it goes blank but that the screen is dying on me. hmmmmmm....... this is quite strange. i can also recieve calls. i cant answer them but the handset rings.
This may be silly but if I were in your place I'd just reflash everything with an official rom that replaces everything (i.e. SA 1.35) and see if that fixes the problem (though i might wait until somebody who knows more then me verifies this is a good thing to try). I'm wondering if the bad flash somehow effected something in your OS or something.
When I mess something up like this, I like to get back to a place which has been known to work - then I have a better idea of where I am (ie brick or bad flash)
Hope this helps
yea i actually went back to the original cingular ROM that came with the phone. so we shall see what happens from here. i also will have Cingular send me a new phone, i was tired of the scratches anyway. So far they havent noticed that my phones are supercid yet. Keeping my fingers crossed
Hardware problem IMHO...
Sleuth u are right. No matter what i do to the phone it yields the same result. My screen still turns off and the buttons dont work. iwonder what couldve caused this. i didnt drop it. well not recently anyway. BTW.... is there anyway to get the original 1.16 radio back on there. i tried doing it but it just hangs at 0%.
Thanks Sleuth for all your help, you are definetly one of the reasons this forum is helpful. That and that good ole WIKI.
OK, let me start by saying I am NOT getting the bootloader, I am NOT getting stuck on a startup screen, and I am NOT new to loading HTC ROMS (but I am new to the titan - former owner of Hermes). With that out of the way....
I bricked my Titan - It won't startup at all. Plugging it into the USB port generates a red LED and nothing on the screen. The only USB activitey seen on the computer is the HTC USB modem (no other communciation appears to be possible - no activesycn, no response to ROM updates etc.
This is the order of the bricking
1. Started with Default Verizon install (less than 4 days old)
2 unlocked with olipro 1.20
3 attempted install of Sprint 3.35 update to get radio (failed and rebooted device at 11%)
4. attempted intall of radio 3.27 (sucessful)
5. installed NexVision 3.35 cooked rom
6. ran into some stability with the rom (phone remained "Unactivated") and reverted back to ruu_signed_verizon stock ROM
7. Booted OK (phoen remained "unactivated"
8. reattempted install of sprint 3.35 (thinking rom instability was due to radio version) device rebooted itself at 11% and failed.
9. installed olipro 2.4 thinking it might circumvent the 11% reboot issue on Sprint ROM.(appeared sucessfull) phone never came back after that.
Now I'm dead in the water... Pulled the battery, Tried a hard reset (2 softkeys under screen/press soft reset) - no change in the device.
are there any secrets to unbricking a Titan?
Starting with the default Verizon ROM, updating to olipro 1.20
Hold off for a little bit, at the moment there is no unbrick, but ImCoKeMaN and jocky are working on this. Your phone now is booting into Qualcomm download mode and it is recoverable. It's just a matter of a patched loader to get a new spl on it...
thank (fingers crossed)... even tried the relocker by ImCoKeMan and it's not detecing the device either...
Time to be patient and wait for CoKeMan to come to the rescue.
just to make sure...
when you tried a hard reset... sometimes people dont know to hold the soft keys for a couple seconds (this is my experience anyway)
jsut for kicks try this again... press and hold the 2 soft keys, press reset button, keep soft keys held down, release reset button, wait a couple seconds then release the soft keys.
Hmmm I remember someone else with a similar problem not too long ago. He thought he had bricked the phone too and was getting the same red led when he plugged it in, but nothing else. His problem was that he had a defective battery. If you could get your hands on a spare battery I'd say try that...I'm not 100% sure it's the battery, and if it's not then I hope cokeman comes through for you...but if you can check that out, I definitely would.
gcincotta said:
Hmmm I remember someone else with a similar problem not too long ago. He thought he had bricked the phone too and was getting the same red led when he plugged it in, but nothing else. His problem was that he had a defective battery. If you could get your hands on a spare battery I'd say try that...I'm not 100% sure it's the battery, and if it's not then I hope cokeman comes through for you...but if you can check that out, I definitely would.
Click to expand...
Click to collapse
Was just about to post the same thing, red LED is definately an indicator of a battery issue, could be defective or just totally dead. If you unplug the battery and reinsert it and then plug in the usb charger without turning it on do you get a green LED? If so I would say battery is 100% discharged and wait for it to charge (I have had this happen). Otherwise if it is still red after that I would say replace the battery (I had this happen on my first titan, it was doa due to defective battery).
jjlwork said:
Was just about to post the same thing, red LED is definately an indicator of a battery issue, could be defective or just totally dead. If you unplug the battery and reinsert it and then plug in the usb charger without turning it on do you get a green LED? If so I would say battery is 100% discharged and wait for it to charge (I have had this happen). Otherwise if it is still red after that I would say replace the battery (I had this happen on my first titan, it was doa due to defective battery).
Click to expand...
Click to collapse
Exactly, all the roms downloaded from HTC recommend having at least a 50% charged battery.
Yup, battery was at 99% before the upgrades. with or without the battery in it reacts the same, with or without the USB in it reacts the same.
I left it plugged in all night, no change.
Solved (but not really)
Since the phone was brand new, Verizon techs took it back as a "faulty phone"... thankfully the Red LED to them means "bad battery" too and when they replaced the battery and it didn't fix itself they exchanged the phone.
It's good that your phone was replaced, but to all the naysayers in this thread, you don't know what you're talking about. If the bootloader won't come up when you reset while holding power and camera, then the SPL is gone and the phone is booting into download mode. If you want to check this, connect to windows, it should find a new device, a qualcom debug port in download mode (you might need a driver for this).
The issue is being worked on and a solution will be found.
wow, i didn't (i did-but not reallly) know that it was really really possible to brick your phone, i thought there would more or less always b e a way out. pretty scary!
Shadowmite said:
It's good that your phone was replaced, but to all the naysayers in this thread, you don't know what you're talking about. If the bootloader won't come up when you reset while holding power and camera, then the SPL is gone and the phone is booting into download mode. If you want to check this, connect to windows, it should find a new device, a qualcom debug port in download mode (you might need a driver for this).
The issue is being worked on and a solution will be found.
Click to expand...
Click to collapse
It's good that your phone was replaced, but to all the naysayers in this thread, you don't know what you're talking about. If the bootloader won't come up when you reset while holding power and camera, then the SPL is gone and the phone is booting into download mode. If you want to check this, connect to windows, it should find a new device, a qualcom debug port in download mode (you might need a driver for this).
The issue is being worked on and a solution will be found.
Click to expand...
Click to collapse
Ok well then I guess you could call me a naysayer then. And I assure you I am no dummy myself, in fact, I'm a Computer Engineer and work with embedded systems alllll day long. I don't doubt your knowledge about the bootloader and the SPL, but before you doubt MY knowledge explain this one to me. Stock battery, no bootloader, no nothing...just red LED. Replaced battery and all of a sudden phone boots...both normally and when forced into the bootloader.
I have the exact same problem. I don't remember exactly how it happened, but was similar scenario to previous posts. I believe I was trying to get the 3.35 radio installed for use with dcd's 3.0.1 kitchen, although I can't be positive.
QPST shows that it is seeing a Qualcomm device in download mode. Here is the exact model# it displays:
Q/QCP-XXX (Download)
Hope this info is useful to those that don't have a titan stuck in this mode.
Yep, that is a brick currently, but a method to fix it is being attempted.
Basically the phone has a dual core cpu with 1 core running the spl, and wince; and the other runs the oemsbl, qcsbl, and amss (the radio). Your spl is missing so the operating system core is doing nothing. However the phone side is still up and running. (this is mostly theory)
So we need to have a patched bootstrap to send in download mode (notice qpst software download actually sends over a bootstrap 7500.hex file found in your qpst bin directory) which will load the spl back into the correct areas of memory. I don't believe we can jump to it because we are on the wrong core.
Do you know which address range the SPL sits in memory?
JTAG ?????
Shadowmite said:
Yep, that is a brick currently, but a method to fix it is being attempted.
Basically the phone has a dual core cpu with 1 core running the spl, and wince; and the other runs the oemsbl, qcsbl, and amss (the radio). Your spl is missing so the operating system core is doing nothing. However the phone side is still up and running. (this is mostly theory)
So we need to have a patched bootstrap to send in download mode (notice qpst software download actually sends over a bootstrap 7500.hex file found in your qpst bin directory) which will load the spl back into the correct areas of memory. I don't believe we can jump to it because we are on the wrong core.
Click to expand...
Click to collapse
Hey Shadow, I think you are correct, and also possibly do you think that JTAGing it would work ? Grad the image from a good one and load it into a dead one. I do not yet have one to take apart yet to try, but if i get a bad one to take apart I might just get it.
It would be great to see this issue resolved as this same problem happened to me last nite and the "friendly" folks at Bell Mobility took one look at the phone and told me it was water damage. I've had the 6800 for about 20 days and it has not been close to water. Anyways, that's besides the point. I look forward to seeing some kind of resolution to the matter....thanks!
Do you see same in QPST ?
Escobar600 said:
It would be great to see this issue resolved as this same problem happened to me last nite and the "friendly" folks at Bell Mobility took one look at the phone and told me it was water damage. I've had the 6800 for about 20 days and it has not been close to water. Anyways, that's besides the point. I look forward to seeing some kind of resolution to the matter....thanks!
Click to expand...
Click to collapse
Do you see this same thing they report with the QPST also ??? Man I would not break mine to fix the problem, but would love to have one to poke at too.
Yes I am having the same problem phone basically dead....
Shadow may fix it, but,,,,
Escobar600 said:
Yes I am having the same problem phone basically dead....
Click to expand...
Click to collapse
I am not going to take mine apart to look for it, but i am sure there is a JTAG port inside these as there is every other I have seen.
im having a problem in which my touch pro will not sync or be recognized by ANY type of usb connection (ie, advanced network functionallity unchecked, disk drive mode) it syncs via bluetooth just fine, and when connected to the computer via usb the dialog box asking which type of connection still pops up and it still charges, but no type of connection will go through, i have tried everything except for a hard reset which is what im really avoiding because i have it finally running exactly how i wanted (complete with manila 2.1 on wm6.1 htc 2.01 rom which took me an hour to get working exactly how i wanted), any suggestions, im going crazy here
eric12341 said:
im having a problem in which my touch pro will not sync or be recognized by ANY type of usb connection (ie, advanced network functionallity unchecked, disk drive mode) it syncs via bluetooth just fine, and when connected to the computer via usb the dialog box asking which type of connection still pops up and it still charges, but no type of connection will go through, i have tried everything except for a hard reset which is what im really avoiding because i have it finally running exactly how i wanted (complete with manila 2.1 on wm6.1 htc 2.01 rom which took me an hour to get working exactly how i wanted), any suggestions, im going crazy here
Click to expand...
Click to collapse
from where i sit, it sounds like u've spent more time fussing with the no-usb problem more than the hour it'd take to "setup" your phone lol.
can you provide any more info? when did it start happening? have you tried from a couple different computers? cables? please give as much information as you have on the entire subject so we dont have to "drag it out of you" as you are the one requesting assistance dont make us do all the work
I have been having same issue with my Touch Pro. It was working great a few weeks ago...then it just stopped...my pc can't sync or recognized the device. I have been doing extensive reading on so many posts...but nothing seems to work. I finally gave up and a did a hard reset last week...guess what? It still did not work. I suspect it might be a hardware failure. Here is what i did and it was unsuccessful:
Install and then uninstall WMD...nothing, bought new OEM data cables (2 to a pack)...nothing, unchecked the advance network functionaility...nothing, someone recommend to swipe the connection inside the phone for possible dust...nothing, tried on my laptop, desktop PC, work PC and my UMPC (all worked before)...nothing, i tried different usb ports on ALL pcs...nothing, started up ICS and connect (supposedly it will install drivers needed)...nothing.
I also notice that some of the chargers I had for it-also stopped working. Only OEM chargers work now.
Also, there are MANY people complaining about this problem as well...
so I use this program, WIFI Remote Access v1 beta 4, freeware to add apps or make changes via wifi. Works great.
http://www.julien-manici.com/
Wish I could find a "fix" for this issue...I can't sent it to Sprint or have a warranty since I flashed it over to Metro PCS...like I said it was working for the past 5 months or so...
drdrewdown said:
from where i sit, it sounds like u've spent more time fussing with the no-usb problem more than the hour it'd take to "setup" your phone lol.
can you provide any more info? when did it start happening? have you tried from a couple different computers? cables? please give as much information as you have on the entire subject so we dont have to "drag it out of you" as you are the one requesting assistance dont make us do all the work
Click to expand...
Click to collapse
well probably last weekend it started happening in which WMDC would just drop the connection and wouldnt reconnect until i rebooted the PC and yesterday morning it also wouldnt connect till i rebooted the pc then it synced and added songs just fine, then i went to school and sat down on one of the computers there and worked on a paper i had to do, this was the last time it worked at all, i got back home and when i connected it to the PC no connections accepted at all, ive rebotted and soft resetted about several times to no avail.
**UPDATE**
i just bit the bullet and did a hard reset and guess what?...........still not working so im resyncing everything through bluetooth and soon will reinstall manilla2.1, after this i will be going to sprint tech support, maybe i can have it exchanged for a TP2
well so yesterday i went up to the sprint store, explained my situation to them and said that ive even done hard resets, they guy had me turn in my phone to him and said that the repair would only take 45mins well 70 passed before i saw my phone again and when i got it back they told me that the reason it wouldnt sync is due to all the 3rd party programs i had installed (only 3rd party program was spb pocket plus) all other installed programs were made by microsoft,sprint and htc. so they did a hard reset and told me it synced their computer fine and that it may be a problem with my computer so got home and it STILL DID NOT WORK!! i even plugged in my axim x51v and it synced without problems,i cant believe i wasted 5 hours of my time and pay an extra $7 for such unprofessional service. they didnt even offer me a new USB cable.
Hey eric,
I have been to other sites and there other members experiencing the same thing. This is the first time hearing it was a 3rd party app...you know it isn't an app if you do a hard reset, which I DID...and it still my pc doesn't recognize it. In my case, it was working great one day...and the next day- it just stopped working.
Now my wif also went haywire. And a hard reset didn't fix that either...
I will be getting the Touch Pro2 soon. I never experience any issues when I had the HTC Mogul...my HTC Pro...well I love it...but i can't deal with the hardware issues...I just replaced my keyboard not to long ago.
Sorry to hear Sprint gave you the run around...
edit: I read somewhere in another post...that sometimes the wifi wire can get unplugged after installing a new keyboard...I opened it up and found the wifi wire (on the back side) plugged in the wrong connector. I must have unplugged it accidentally and then plugged in on the wrong connector. Found the error...now wifi works great.
I've began to have the same issues as well. Last week I flashed vet's ROM and thats when it died. I tried hard resets and other ROMS and its still the same thing so I dont believe it was vet's ROM but more of a hardware issue.
I have no activesync functionality, no flash ability over USB, but charging and disk drive work fine.
hemirunner426 said:
I've began to have the same issues as well. Last week I flashed vet's ROM and thats when it died. I tried hard resets and other ROMS and its still the same thing so I dont believe it was vet's ROM but more of a hardware issue.
I have no activesync functionality, no flash ability over USB, but charging and disk drive work fine.
Click to expand...
Click to collapse
I never had this issue. Only internet stops working with the weather updates and skyfire, Im on metro, I just reflash the cab for the internet and that fixes that. But did anyone else try flashing a new rom like hemirunner426 did? Could be worth a shot to get it working. Sounds like urs is F'ed dood sorry.
well I bought a new usb cable from ebay for only $3.xx and since it arrived my usb functionality was restored.
Its usually a problem with the usb cord. I had this same problem before. Just go to the sprint store and they will exchange the cord for free, they also redesigned the cord do it doesnt keep breaking.
ravioli817 said:
Its usually a problem with the usb cord. I had this same problem before. Just go to the sprint store and they will exchange the cord for free, they also redesigned the cord do it doesnt keep breaking.
Click to expand...
Click to collapse
well they didnt exchange it for me,they wanted me to pay $25 for one ,descarados!!
me too
I have been testing energy and veito roms and started to get the same problem as everyone here having to reboot both tp and pc to get it to connect I get it to sync but if I leave it on it disconnects and I get usb device malfunctioning or unable to reconise device so I called sprint they told me to go to the repair center I pay my tep for 7 buck he told me it I had damaged the usb port the plastic in side was broken it had been like that from when I got it new he said it would cost me 100.00 for the Insurance to get a new one I went to the other repair center said almost the same thing the bull about this is the tep they are suppost just fix the phone no matter how the phone is broke even tho it was not broken so I called sprint they put me thru to tech support they offered me several replacement all junk phones or a refub tp so I took the tp wouldn't give me a tp2 think I am going to call retention and complaine now that I see I am not alone with this problem
I'm suddenly having this problem now.....I have switched to 2 different computers (freshly formatted), flashed to 2 other ROMs via SD card but still no luck with the sync through WMDC.....It charges the phone but will not sync. Any ideas from the gurus??
eric12341 said:
well I bought a new usb cable from ebay for only $3.xx and since it arrived my usb functionality was restored.
Click to expand...
Click to collapse
I also bought the OEM data cable for the TP....no cigar...still doesn't work. Happy to hear you got yours working.
like its said in the title, my titan resetet itself twice! without any obvious reason.
the first time the titan didnt react to anything so i removed the battery, when i startet it again -> get started stuff
the second time i just turn the titan off when i restarted -> get started
its pretty anoying and i wanted to know if anybody has the same problem or knows an answer
thx
Memory full ?
What your device memory nearly full or about 8GB full ? Some devices have a bug when this happens. The last deployed firmware resolved the issue for me.
mhm im not sure how much was full but it could be...
i will do the update and see if it solves the problem
thx for the tipp
edit: great ive wanted to update my phone but during the process it fails. at the point when the phone is restarting my pc doesnt recognice it anymore...
zune is waiting for the phone to restart and the phone shows this "connect phone to pc" screen but nothing happens...
You can try to update your firmware with the lastest version with a recovery tool here:
http://forum.xda-developers.com/showthread.php?t=1334468
It worked for me but you'll loose all your data.
ok thx i will wait a few days and look for driver updates mabay this will fix it and i can update the normal way but thx
My phone keeps shutting off and I barely have anything on it. Pretty annoying, thought it was a defective phone, not sure after reading this.
edit: after doing a factory reset my phone is still shutting off. Going to get a new replacement today.
I read on another thread that cleaning SIM card and reseating it solves that. Hope this is not too late to help others.
Any similarities to this?
http://forum.xda-developers.com/showthread.php?t=1339185
I just had my first reboot for my Titan. Incoming call but no sound. Hung up, and the phone immediately rebooted. First and only time it did that. Hopefully it was an isolated incident.
FYI: I have about 4GB free on my phone. No other issues.
i think some of you getting it wrong. my titan doesnt reboot it reset itself like a hard reset, everything is gone and i have to go trough the whole settup again...
this happened twice altough it havent happened in the last days i want to update my phone but its impossible for me right now because when my phone restarts during the update process zune doesnt recognise it anymore.
ive already deletet and reinstallt the driver and i ran the official microsoft fix without any sucess
Tempest790 said:
I just had my first reboot for my Titan. Incoming call but no sound. Hung up, and the phone immediately rebooted. First and only time it did that. Hopefully it was an isolated incident.
FYI: I have about 4GB free on my phone. No other issues.
Click to expand...
Click to collapse
Mine did this twice this week. I think is something with network connection.
Everytime I took it from pocket or car, turned it on and call in seconds.
Sometimes I got restarts while using the bluetooth connected to my car.
Something it not good with HTC radio.
=\
HTC Titan resetting itself out of nowhere..??
My Titan reset itself for the 1st time yesterday.. it froze first so i couldn't power it down I had to take the battery out, only thing is I have all my stuff (music, pictures, text messages..) u get the point. So after that happened and i pulled the battery out and put it back in and powered it up some of my apps were uninstalled and when i went over a screen to my apps i noticed something that said "applications install" or something like that, i had never seen it before. I uninstalled the mysterious app or watever it was and now when i try to open my people block on the start screen to find contacts it wont work.. wont open at all!!! this is the 2nd titan ive had and im totally confused as to what going on. I did unlock it with an unlock code. I dunno if that has anything to do with it.. Can anyone shed any light or should i just count my losses and trash it! it also deleted my email accounts in settings when i powered it off then on again.. I dunno if its a bug or wat, but im pissed tf off!! hellppppp!