I have unlocked with Olipro's hardspl, and flashed the 1.50 radio, how do i go about installing the rom. I've already downloaded it. Do i have to run it from my x7501?
Anybody there??
Someone knows how to install this ROM. Neither my desktop, nor my x7501 recognizes the file type "There is no apllication associated with........" So how do i install this thing??
When i run the RUU, its trying to flash the radio again, i've already got the radio. Ineed the ROM.
Nevermind i got it. Thanks for all the help though.
Related
Hey u guys, I have 2.60 SPL Olipro (it gave an error when installing it on the 100%, but in bootloader mode its what appears so i guess it is installed ). Either way Im trying to update my Radio ROM and i cant seem do it. Ive got the radio rom file and the custom RUU, although everytime i try to update it gives an error at 7% an the PDA gets stuck in the bootloader and the only solution is to install the orginal HTC ROM. in addition, the phone is not Super CID or something, it is unlocked by factory...
Geez nobody here can tell me how to flash a radio rom? i have superCID, hard spl 2.10... I already have the radio rom i want and a custom ruu, but it always gives me a "flash write" error.
OK I received a brand new xv6800 from Verizon today. Haven't even activated it yet. Wanted to update it first. So i downloaded Hard-SPL-MFG.exe and ran it. I get to the boot loader screen and it reads 2.40. Then the directions state disconnect cable and reconnect. I do that and the boot loader shows that it is connected via USB, however I cannot get a new activesync connection unless i restart. But when i restart lose the 2.40 bootloader. and the update errors out. I have tried the titan exitbl file but it cannot find the usb connection.
What am I missing?? Do I need to go the SD card route (dont have one yet)
My bootloader is 1.04
Any help would be appreciated
Don't worry about activesync after you replug it in. Just keep following the instructions. As long as when you plug it back in, it says USB at the bottom, just keep going.
Ok that sort of worked. Now im stuck at the 2.4 bootloader screen Fun stuff
You can run the fix from here.
The same fix is probably posted here too I just don't know where.
Thanks ran that again and it worked so I am back in business. Since you happen to be here any suggestion on which kitchen and radio to install
See this post. It worked for me.
Im working on radio and got it from your link but there is no link in the post to a kitchen i was going to downlod the latest one fromt eh lifesnotgood link which is called "dcd_titan_kitchen_3.2.2.rar" that should work right?
I have never used DCD. I use ppckitchen.org. You may want to consider just loading a custom ROM first unless you know how to install and use a Kitchen already. Sometimes it is easier to flash a prebuilt custom and get your phone working, then start cooking and flashing your own.
With the ppckitchen you don't have to do carrier cabs, you just select your carrier in the kitchen.
OK i really appreciate all the help and I know i sound like a total noob but went to ppckitchen and everything i see is a kitchen i dont see a full rom, what am i missing
They only have the kitchen to make a ROM. belive DCD has some custom ROMS.
Thanks for all your help all installed and running, now just need to activiate with verizon
'Have a li'l question about updating to Olipro myself...
I could've swore that b4 I'd upgraded to Sprint OEM ROM v3.56.651.0, I could update to Olipro v2.40 via SD. Now, however, I'd had to do so via USB. Am I mistaken? Can you not use the .nbh file in the .exe pkg? I like bein' free of HAVING to use a desktop to accomplish PPC tasks.
Thanks, Everyone.
Just download DCD's 3.2.2 ROM on the 1st page of his post. He has a kitchen AND a ROM.... http://forum.xda-developers.com/showthread.php?t=407376
As for using NueSPL 2.47, DO NOT use it until No2chem has finished his research on downgrading XV6800's.... While it has distinct advantages over olli 2.4, he's not sure about downgrading the bootloader to 1.X versions..... That is if you ever have to take your phone into verizon for service....
Hi,
i have been attempting to sim unlock my dual for some time now using the instruction on the SuperCID sticky.
I can install custom rom's fine normally but when i attempt to use the special patched radio rom needed for unlocking it always stops at 95% and then i get a communication error.
I was trying this in vista with the drivers patch from Modaco but i have also tried this with XP sp3 and get the same problem.
is there anyway to trouble shoot this to find out what is going wrong? i have ever tried installing the radio rom from the SD card but that doesnt work
thanks in advance
Colin
i get the same proplem also. I can flash any rom, and other radios....just not the patched radio for superCID.
Try to flash this radio first. Then try the super CID process again.
Guys ... use a old 1.58 Radio first ...
thanks guys, i'll give it a go!
1.58 radio does the job. anyone else who gets this problem rememeber to 'downgrade' your radio to an earlier version and everything should go well. Also dont bother trying to use vista, it has lots of problems with this procedure.
I recently flashed my Wizard with TNT WM6 and I am getting all kinds of problems so I am wanting to bring it back to Wizard Love so I can attempt TNT's again and avoid a "bad flash".
My question is, do I need to put the phone in the bootloader (i.e. the 3 colored bars?) or can I flash it with the phone loaded and everything. I am using RUU to flash.
Or do I need to use ShellTool?
If its a G3,then simply hook up the phone with pc and run the RUU,it'll reflash,there's no need to get into Bootloaders (RGB Screen).
But if its a G4,then how did you upgrade first,if through HardSPL,then again just hook up and run the RUU,well,if you used Shelltool,then there's no need to go through again with Shelltool.Get the phone HardSPL once,then you can flash any rom as much as you like
I used shelltool for the first flash, but it kind messed up so I had to redo Wizard Love with the RGB boot loader.
If I remember correctly by "messed up" I think it froze during flashing.
Yes I do have a G4
well do as zabardast_1's has said and flash HardSPL to your g4 wizard and then you can just flash another cooked rom
and added....Don't use ShellTool again even you are using a G4! RUU can be used on G4 directly given that you have installed HardSPL and you are going to flash a custom ROM posted here.
So even though ShellTool kinda messed up, my device is still HardSPL'ed?
To be safe you can flash using Softspl , that is the way i flashed few times althouhg my wizard was hardspl and it was ok. If you have hardspl try using Mun's RUU . Both methods worked fine for me.
Ok, I just re-flashed my G4 with Wizard Love using the RUU that it came with and everything seemed to work fine. Does this mean that my HardSPL was successful? See what I think had happened was I flashed TNT's rom with ShellTool and not RUU after I had HardSPL'ed my device. Could that have had something to do with it?
Thanks for all the help so far, you guys have been very knowledgeable.
Read this maybe its helpfull for you http://forum.xda-developers.com/showthread.php?t=435852
Mortifix said:
Ok, I just re-flashed my G4 with Wizard Love using the RUU that it came with and everything seemed to work fine. Does this mean that my HardSPL was successful? See what I think had happened was I flashed TNT's rom with ShellTool and not RUU after I had HardSPL'ed my device. Could that have had something to do with it?
Thanks for all the help so far, you guys have been very knowledgeable.
Click to expand...
Click to collapse
Ah! You are mixing up all three methods Shelltool,RUU,HardSPL together,they all are different methods to flash a rom.Shelltool is a different method then RUU(RomUpdateUtility) and HardSPL(Patched IPL/SPL) is altogether a different process to flash and upgrade a G4 device.
Try to read all about these methods for better understanding.
Here, I wud not like to go into details,you can read about these methods in their respective threads.
Flashing wizard_love rom doesn't mean your phone is HardSPL'd ? No,wizard_love rom is a patched rom,it'll flash to any G4 device with original official IPL/SPL (Bootloaders) running on it,but if the phone is HardSPL'd,it flashes patched IPL/SPL,thus tricking it to think its semi-permanent CID unlocked,after this its possible to flash any wm6.1 custom rom.But flashing a wizard_love,it still has its own official IPL/SPL,but you cannot upgrade to any wm6 rom as its not CID unlocked.As a G4 device cannot be CID unlocked like a G3 phone,so KardSPL is applied to make it trick into semi-permanent CID unlock,whereas,its in fact CID locked,but here its possible to upgrade to any wm6 rom,hope you got my point !!!
So,if you want to upgrade to wm6 or flash TNT wm6.1 rom,you have to first apply HardSPL,it'll change the IPL/SPL of the phone,only then you can flash TNT wm6.1 rom
Ok yeah thanks for clearing that up for me I was trying to update my phone with the RUU that came with TNT .20273, but it kept giving me an Error 300 which I am assuming that means its not HardSPL'ed. So from the sounds of it, I would probably like to get my phone HardSPL to I can flash any new roms that come out. I was under the assumption that ShellTool was HardSPL'ing my phone, but I guess not. Before I proceed to the next step, is this the instructions I should be following?: http://forum.xda-developers.com/showthread.php?t=332320
EDIT:
Ok, I went ahead and HardSPL'ed my device. I followed the instructions on that thread and everything seems to be working. I get SoftSPL: something something olipro so I am guessing thats good. I am still having problems when I go to flash TNT. I am trying to use the RUU that is included with TNT, but I keep getting Error 300 (Invalid Update Tool).
ok,download 'Mun's RUU' from the HardSPL thread you just posted above and replace the RUU in this zipfile with RUU in the TNT rom and run this replaced RUU,it'll work and flash the rom
I have everything all set and I am rocking TNT .191213. Thanks for all the help guys!!
Hi I'm looking for some help. I tried upgrading my XV6800 to the windows 6.5 rom but I think I might of messed up. I tried to update my radio first but ran in to issues.
I used Oilpro 1.20 to try and tried to update the radio but along the way messed up while trying an older rom and I'm currently at a Verizon screen with the message "NO RADIO" at the bottom. I'm assuming the radio rom was erased. I might have gotten confused with the roms and used a rom without the appopriate Radio. When I try to flash that rom back to a stock Verizon upgrade it just ends 11% in to the flashing process and the rom update utility returns a Error 290 screen.
Currently I can get the oilpro 1.20 bootloader to still load up but I'm not sure what to do at this point. I tried updating the ROM to DCD's older 3.20 roms, which did complete but I still have that screen coming up. Can anyone give me some suggestions on what I should do next? Any help would be greatly appreciated.
Try using NueSPL 2.47 it's more current
Doesn't have have to be run on the phone itself once inside Windows? The only screen I can get up is the Verizon (splash) screen where it normally lists the rom and radio, or the oilpro boot loader screen. I actually can't get back in to windows to run the nueSPL 2.40.exe file.
Is there a way for me to flash the radio back from a bootloader screen and USB or SD card? The thing is I actually tried to take the 3.42.40 radio and use the Flash Rom Utility to see if it would flash the radio rom back on but even though the process completes successfully, I still get the no radio error so I guess it doesn't work. Thanks for the help, I think I may have been a few of the idiots out there who screwed things up and didn't make sure the radio was up before attempting any rom upgrade.
You should've changed the bootloader first. Your radios that you are trying are not compatible with your bootloader.
Flash an old stock rom via SD, then update your bootloader to 2.47 once you can get back into windows, then update your radio, and then your rom.
Yeah that was one of the first things I've tried a USB update back to the stock Verizon 6.1 ROM, but for some reason it prematurely ends at 11% with the PDA Phone Update Utility throwing a ERROR 290 message. This is the first time this has happened as I've flashed with this same rom tons of times. I've been looking online for the past hour on how to flash the ROM from a SD card if I can't get in to Windows. But all I could find was the USB update utility and it ends at 11% Am I doing it wrong? any ideas would be greatly appreciated.
If you can still get in the bootloader then you should be fine....I would put it manually in bootloader holding power and camera simultaneously and poke the hole to get it into bootloader.
Once you do that plug in the data cable and run Olipro 2.40 or Nue 2.47. It should be able to take after that.
Basics steps to flashing a phone:
correct unlocker-->stock ROM-->custom ROM
Most custom ROMs will not include Radios that why you would run the stock ROM first to install the radio and then run the custom ROM. Alot simpler then trying to update the Radio by itself.
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Beyond888 said:
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Click to expand...
Click to collapse
Glad to hear you got your phone back up
As far as I know you should be able to just install 2.47 and it will overwrite your old bootloader without problems. I could be mistaken but there isn't really a way to "uninstall" a bootloader, just overwrite it with a different one.
unL33T is correct...just run Nue 2.47 and let it overwrite the old one. 8p
Yeah that's what I thought too, but when I tried to over right it with 2.47 the 1.20 showed up again so I used the titan_relocker tool. Maybe I did something wrong. I'll go recheck, thanks for the replies guys.