Really need help here. I have bricked my phone in the past, but was always able to restore it. Not this time...
I have IPL-1.04 and Olipro 2.10 SPL.
Tried to flash a new wm6.1 room and got a failure on 0%. The device reboots, goes throught the installers recovery procedure, then loops into this process again and again, always failing on 0%!
ANY HSPL ROM that I try to flash ends the same way now so I cam stuck in tricolor mode.
I wanted to try to flash a new ROM from the bootloader screen (this is all I have now), but no lnb command. Since I have Olipro 2.10 I can't flash 1.01mfg IPL...
I've scoured the forums / googls, but after hours of trial, no solution.
Help!!!?
update
ok... the old "set 14 0" didn't work, but "set 16 0" did!
I can now get back to the OS!
Only problem now is that any ROM I flash still results in crash on 0% and back to square 1...
Any ideas why this would happen? I am trying to flash in HSPL mode BTW.
try flashing using the sd card
Fixed
can believe it yet - but it seems like a bad USB cable did this.
I still can't believe it, since mtty communication worked fine, but tried new cable and I'm back in business... go figure...
Related
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up.
Now, the phone is dead completely. I can''t even enter bootloader mode.
Is there a possible way that I can still save it??
Help!!!!
Have I bricked my device? Help plz
I managed to upgrade my phone to aku 3.3 using pof's method(bootloader 1.01 MFG) . Then, out of no where, I tried to use MTTY to upgrade my radio rom
It started as usual with the status bar moving. Suddenly some error messages came up. Can't remember exactly, but like some address can't find error.
Now, the phone is dead completely. I can''t even enter bootloader mode. Only when I take out the battery and plug in the charger cable the red light comes on. I looked the upgrade problem page, my symptom doesn't match any.
Is there a possible way that I can still save it??
Help!!!!
I had something similiar happen a little while back. What I did was pull the battery out and leave it out for a while, maybe a few minutes. I then put the battery back in and held the two side buttons and hit the reset button to put me into bootloader mode. I then cabled it to my computer and flashed a new OS via mutty. That got my phone back and operational.
@float. Nuh, it didn't work on my brick. Prob i will have to take it back to Tmobile if they kind enough to repair the no warranty phone i bought on ebay.
Sorry to have opened a new thread, I was so desperate.
Plz delelte it.
how exactly did you try to update the radio using mtty?
I download the 1.27 shipped radio rom. P.S. It seemed to be a german version, not sure whether that caused the disaster.
Using NBHextract to get the single GSM.NB file, then in MTTY, typed
USB> task 32
USB> lnb GSM.NB
Before flashing, just had it upgraded to the HTC AKU3.3 OS rom only. The old version radio rom version before flashing was 1.18.
Maybe the order i flash is wrong. I flashed OS first then the radio rom.
just guessing
ok, you loaded the radio rom code where os.nb should go. That may have caused mega bad blocks in flash. Can you even get bootloader mode if you reset using Wiki directions to obtain Tri-color bootloader?
Yes. I have tried many ways wiki suggests. Such as removing the battery leaving it more than half an hour and plugging it to the usb cable without battery. still can't get to the tri-color bootloader mode. Basically, I just can't turn on the phone.
If you connect it to the computer, can it communicate w/the PC? If you hear the windows tones try opening up mtty and see if you can communicate.
i'm stuck in the same place
for me it happened during extrom flash
Try removing the battery for a bit (a few minutes, maybe half an hour). Then, put the battery back in but don't plug the usb cable in. After that, hold the two side buttons as if you're trying to get it to go into the bootloader. Hit the reset button a few times with your stylus and see if that gets you to the bootloader. That's what worked for me.
tried that
tried removing battery and connecting usb
nothing helps
is there a place that fixes tytn in belgium ?
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
diffda said:
is there a way to flash a new rom via mutty ?
cause i still have the boot loader, but the phone still in the splash screen
when i type info 2 in the mutty command prompt i get this answer
Cmd>info 2
HTCSQTEK_203”µ·êHTCE
i think it's not realy normal
Click to expand...
Click to collapse
well your not supercid... your still locked to qtek
Look here and unlock your phone before doing any flashing!
http://forum.xda-developers.com/showthread.php?t=295751
to late i ve done that tow day's ago , now the only way to make my phone back to life, PB + KITL method i think
god bless KITL
I have one Tytn that was bricked while flashing Radio rom. I tried everything that I could find on this forum and nothing (flashing from Win, flashing form SD card, tried with mtty - no luck). When I try to flash any radio rom it stucks either on 0% or 12%. I could boot the OS, but the problem now is that I wanted to try one more thing - to downgrade SPL (it was IPL 1.04 and SPL 2.30 Olipro). I used Hard-SPL v7 first but it didn`t downgrade, and then I tried the procedure for downgrade from mrvanx, frist with Hard-SPL v2. And then I was shocked. After the flashing procedure was 100% complete the device turned off, and now I can`t turn it on. I removed the battery for couple of minutes - nothing. It`s dead. It is like there is no battery (it is not the battery, i tried with another one that works), nothing happens when I press the power button.
Did someone had this problem. Is there any hope it could work. If I can`t bring it alive, could the HTC service do it???
Sorry for opening this topic that fast, but i was in a shock when it happened. I succedded to bring it on, I didn`t know that hold the reset button longer! Maybe this could use to someone. Never give up
Mixa84 said:
I have one Tytn that was bricked while flashing Radio rom. I tried everything that I could find on this forum and nothing (flashing from Win, flashing form SD card, tried with mtty - no luck). When I try to flash any radio rom it stucks either on 0% or 12%. I could boot the OS, but the problem now is that I wanted to try one more thing - to downgrade SPL (it was IPL 1.04 and SPL 2.30 Olipro). I used Hard-SPL v7 first but it didn`t downgrade, and then I tried the procedure for downgrade from mrvanx, frist with Hard-SPL v2. And then I was shocked. After the flashing procedure was 100% complete the device turned off, and now I can`t turn it on. I removed the battery for couple of minutes - nothing. It`s dead. It is like there is no battery (it is not the battery, i tried with another one that works), nothing happens when I press the power button.
Did someone had this problem. Is there any hope it could work. If I can`t bring it alive, could the HTC service do it???
Click to expand...
Click to collapse
I have your same promblem..
Once downgraded to old spl you were able to upgrade the radio rom?
Is it correct?
I thought that I will be able, but it seems that my radio bootloader is corrupt. I am reading now the forum, and I think (if I understood it) that I have to write raw radio rom (.nb file). Am I right? Anyone!
Hi gents,
I finally managed to put my hermes in unusable state and would appreciate any suggestions to get it working again.
Here is the situation: My phone is Hermes 200 with SuperCID and bootloader IPL-1.04, SPL-2.10.Olipro. Currently it sits stuck in tri-color bootloader mode and it doesn't matter what I do. Within last 24 hours I tried to change the boot flags "set 14 0" and "set 16 0" respectively at least 50 times without success. I flashed about 6 different versions of roms including original HTC distributions for WM5. Nothing happens.
As far as history is concerned, I flashed many roms since Black 1.0 onto my TyTN without any problems. two weeks ago, I tried one of Pay's roms trying to get something faster then Schap's 4.22 I was using. Got stuck in BL but could recover using the "set 14 0" and "set 16 0" commands. since then, I had couple of occasions where phone got stuck in BL after rebooting it. Removing and reinserting battery always helped. Last thursday, I donwgraded my radio from 1.54 to 1.43. You all know the reasons. No problems. Since then, phone worked like a charm and even power consumption was good. Yesterday, my battery ran out and in order to preserve it, I turned of the phone. Stuck in BL since then.I believe that the problem is that my SPL got somehow corrupted.
So my first question is, how do I reflash HardSPL from WITHIN BL with no access to OS? I can still talk to my phone BL through mtty and get all info etc.
Again, any help would be appreciated.
Roman
Please remember I'm new at this, but have you tried the sd card method of flashing? Hard Spl ver 7 has an .nbh file like a rom upgrade so this may be your best bet. Cheers.
Can't flash with SD card
ultramag69 said:
Please remember I'm new at this, but have you tried the sd card method of flashing? Hard Spl ver 7 has an .nbh file like a rom upgrade so this may be your best bet. Cheers.
Click to expand...
Click to collapse
Didn't try it first as my SD card contains programs/data which I would like to backup first before formatting it. Unfortunately, my laptop with XP refuses to recognize it as a formatted drive for some reason after insertion. I have 2GB KingMax with adapter.
From SPL 2.10 Olipro to dead phone. It's getting worse every minute.
Well, guess what. My phone just decided today, around noon to boot into OS! even though I tried to reboot it several times during morning without success. So I left it alone, without resetting it until I got home. Spent plenty of time reading wiki and upgrading posts etc. While doing that, I backed up my SD card via ActiveSync file access and erased everything on the card. I also copied HardSPL v7 RUU_signed.nbh on it and renamed it to hermimg.nbh.
Going through all the info, I decided to try DOWNGRADE SPL 2.10 to 1.10, following mrvanx's guide and links, as it is still HardSPL. Well, the update process went without a hitch. It loaded SSPL on TyTN and flashed it with 1.10. No errors. It reset the phone and stopped in BL. Again. This time, it says 1.10 Olipro as it should. Going ty mtty after USB connection, and running info commands, reveals some differences as info 2 NO LONGER reports SuperCID as it did before. It just prints the HTCS marker. The phone is still SuperCID I believe as task 32 reports level=0.
Remembering that removing and reinserting battery sometimes helped ( I forgot to try the set 14 0 and set 16 0 ) I removed the battery. About ten minutes later and more wiki reading, I realized I should try the set flag commands. So I reinserted the battery, reboot and NOTHING. And I mean nothing! The phone is as dead as it could be. NO LIGHTS , NO DISPLAY, NO RESPONSE WHATSOEVER. Did I just foo bared my IPL ?
Sorry to hear that, best bet would be to pm Olipro and see what he has to say. He is the Guru when it comes to SPL. He may have an idea but if you cant get into bootloader then phone is probably foo bared, Still, I'd see what he has to say, might pull a miracle out of his hat...
Resolved. My TyTN is alive again
See post http://forum.xda-developers.com/showthread.php?p=1867765#post1867765 for the end of the story.
open mtty and put this command.
Put hermes in bootloader and disable activsync,
open mtty.exe select usb and put this command:
set 32 (enter)
set 14 0 (enter)
set 16 0 (enter)
task 28 (enter)
task 8 (enter) After this command hermes will automicaly boot os if not then your os is demaged just flash full rom.
what you see when write this command in mtty :
checkimage (with this command you can see status of full rom)
gsmhackerns said:
Put hermes in bootloader and disable activsync,
open mtty.exe select usb and put this command:
set 32 (enter)
set 14 0 (enter)
set 16 0 (enter)
task 28 (enter)
task 8 (enter) After this command hermes will automicaly boot os if not then your os is demaged just flash full rom.
what you see when write this command in mtty :
checkimage (with this command you can see status of full rom)
Click to expand...
Click to collapse
I did the resetting of flags multiple times. No joy. I tried to do the NAND formatting as you suggested, nothing. Reflashing with shipped rom, nothing.
I ran checkimage so many times over last week, I lost count.
Stil BL only...
rronge said:
I did the resetting of flags multiple times. No joy. I tried to do the NAND formatting as you suggested, nothing. Reflashing with shipped rom, nothing.
I ran checkimage so many times over last week, I lost count.
Stil BL only...
Click to expand...
Click to collapse
my God !!! that's the worst brick i ever heard, Hybrid brick ???
From the 1st post, I saw all of the effort you use and that's the way should be, but no result.
I think you should re-consider to buy new gadget then. This is for your health too
ermenzegna said:
my God !!! that's the worst brick i ever heard, Hybrid brick ???
From the 1st post, I saw all of the effort you use and that's the way should be, but no result.
I think you should re-consider to buy new gadget then. This is for your health too
Click to expand...
Click to collapse
I still think it's fixable. When I turn the power button on, or plugin the charger, there is significant delay ( about 1.5 - 2 seconds ) before the BL starts. I think that the IPL is trying to boot the OS image but something goes wrong and it aborts and starts SPL. If the NAND is corrupted, it could be re-verified by a proper walkthrough and marking of bad blocks. I have done this at work while writing device driver for another Samsung NAND. I still have the code somewhere. Unfortunately, I don't know how to make it into signed nbs so it can be loaded and executed by SPL as a diagnostic utility.
rronge said:
I did the resetting of flags multiple times. No joy. I tried to do the NAND formatting as you suggested, nothing. Reflashing with shipped rom, nothing.
I ran checkimage so many times over last week, I lost count.
Stil BL only...
Click to expand...
Click to collapse
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
If somebody else create solution before me please sent me message to know??
Do not post any solution from this site i try all and not work(SD card will not work when cid locked,hard spl-not work always 100% then message image corrupted,No kitl.....so please only original solution not from xda-developers..etc.
thanks for all.
Just did the titan unlocker and now the p4000 is stuck in bootloader with these 2 lines:
TITA100
SPL-1.20.Olipro
i think i need some help
thanks in advance
Marc
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
orangeworx said:
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
Click to expand...
Click to collapse
yes..............
since i'm stuck in bootloader mode, how can i use the ruu update utility ?
i'm getting connectiong failed and only option is to exit utility
any ideas ?
if u are in bootloader connect the usb cable and the phone should say usb at the bottom, just open up the ruu update and it should work just fine
Error 264
update utility cannot connect to your pda
and it says USB on the bootloader screen
SPL is 1.20 olipro
take your SD card out if (with phone powered off) if u have an image on the SD card and retry
no SD card being used at the moment
edit: it seems now it is flashing...
let's say this does work, fact that i'm putting a sprint ROM on my telus phone is gonna be alright?
re-edit: crashed at 11% - invalid command error 290... RUU encountered a communication error
recovery
at 11%, titan reset and went back into bootloader mode, RUU crashed but gave option for recovery which was "successful"
retried the same RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.04_PPST_0619_Ship.exe
and crashed again at 11%
i think i killed my phone
i can't seem to do anything, not the telus wm6.0 ruu nor the one stated earlier...
is there a way i can revert to my previous SPL 1.04 ?
really appreciate the help @ 5:35 AM
got my telus wm6 to run and then decided to up to olipro 2.40
now it won't got past second splash...
radio is 1.32, rom is dcd 3.2.5
now from my understanding of what i've been reading is that i need to revert to olipro 1.20 to be able to flash my radio
and i can't do that since i can't get activesync.
any ideas ?
Get a SD card. Go to WIKI and following reverting to Stock. Then start over on flashing. I have done as you did and fixed the phone.
your phone sounds jacked up, how long is it stalling at 11%, r u giving it decent enough time?
redownload the latest sprint rom from htc america here:
http://216.139.227.226/RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship.exe
let it run for at least 20 minutes before deciding it crashed...after 1st boot softreset before letting it run any customizations
Got a problem. I wanted to upgrade to new OzRom today so did normal tasks I did last 40 times.
get new rom and unpack it.
Rename image to LEOIMG.nbh and put it to root of SD card
perform mtty task 29
reboot, phone goes to bootloader then goes to normal grey screen it just says loading and that is it. It gets stuck there.
I had tried flashing via sspl, it sees the phone, screen on phone changes to black htc screen but loading bar sticks at 0%
I have HSPL 2.08 on the phone, I tried to re apply HSPL but it states error with usb connection. Can not upgrade radio from sd card or via sspl as well.
Did try previous rom that worked but it also does not want to load?
Any ideas?
Try flashing back to your original rom. Try that via sd card which should replace hspl back too your stock spl and then start the process from scratch.
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
pnjboyzz said:
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
Click to expand...
Click to collapse
It is odd that it did it now as I have not had any problems for last 8 months
Did not work!!
Update is that I managed to do the HSPL3 again over USB which I could not do before but I can not flash any roms.
Have you tried flash to ActiveSync????
Ok got it going again.
I hade my HSPL as 2.08.0000 and cotula signs all over it. Flashed again and it again went to the same one. However apparently .0000 means it is stock (no idea why stock rom did not want load). Flashed it again to HSPL2 and then upgrade to 3 fixed it.
alesscam said:
Have you tried flash to ActiveSync????
Click to expand...
Click to collapse
It would not help as I have done mtty before so no os on it.
no problem with mtty...
after mtty
you can press red botton for sofreset and press volume down for go to Bootloader
from bootloader you will see USB ,
this if your leo is connect to PC