Related
!!CRUX!! MUST READ!! LazyTool & HardSPL & 3 color screen solution before BRICK~~~~~~~
20100130: post 2 updated
[size=+2]!!!!!!!!if you messed up with G3 & G4 model before flashing, your Prophet will be PERMANENTLY dead (unless a replace of mainboard +_+) DON'T TRY IT @ HOME !!!!!!!! [/size]
[size=+3]( DON'T forget TO HARDSPL YOUR DEVICE before flashing !!! )[/size]
20091204 update:
[size=+2]1. Lazy_Tool is for flashing all 6.1 and 6.5 prophet roms but NOT FOR VISTA or se7en operated computers.......2. VISTA FLASHING click HERE -- thanks to dear CLOUDYFA[/size] P.S. You can just replace the "*.nbf" FROM the UNZIPPED folder
WANNA FLASH FOR WM6 ROMS? please read @ end of post #1 ^_^ )
[size=+3] Additional RECOVERY steps for 3 colors screen boot-up after flashing...[/size][/color]
a. Force Bootloader Mode MANUALLY (see below Point 4 for How To ),
b. Then flash NVID - a AKU 2.* WM5 rom for recovering your Prophet.... ( P.S. the boot up screen will be changed to Qtek...)....^_^
Click to expand...
Click to collapse
**************************************
1: 3 coloured screen??????????? "DON'T PANIC",
2: 99.9999% CAN BE RECOVERED BY
DOWNGRADE TO WM5 WITH MANUALLY entering BOOT_LOADER MODE + flashing the NVID
3: IF USB CONNECTION ERRORS, TRY REMOVE BATTERY FOR 1 MINUTE and try again.
4: FORCE TO BOOTLOADER MODE MANUALLY HOW TO....
4.
4a. keep pressing the Commgr button and
4b. in the same time keep picking/sticking the bottom softreset button with stylus for one second,
4c. [size=+2][highlight] THEN ONLY ONLY RELEASE THE STYLUS[/highlight][/size] and wait for the screen
TO CHANGE to the three color screen (bootloader mode),
4d. then release all and go to step 10 below..... !!!
Click to expand...
Click to collapse
Steps to HARDspl your prophet
5. connect your prophet to computer (activesync done and Hardreset before so will be highly recommended !! )
5.1. In the Upgrade_HardSPL folder that you had downloaded AND UNZIPPED,
then look for the xxx.bat file and double click it (updated 20091114), all activities will only take 2-3 minutes and nothing will be seen in the Prophet screen.
(P.S. if connection Error, NO PANIC, soft reset OR remove battery for half a minute and try again.)
6. after the flash completed, it will restart automatically.
7. done!! in your prophet, nothing will be changed VISIBLY EXCEPT the digits IN the reboot screen !!!!!
and while booting now YOU MUST BE ABLE TO SEE information like:
Prophet Hard SPL isn't yet completed until the SPL shows
2.G3.4PDA (FOR G3 PROPHET) or 2.G4.4PDA (FOR G4 PROPHET)
Click to expand...
Click to collapse
(P.S. REPORTED !!! some device are not able to complete the CHANGE VIA Hardspl,
(like mine, NEVER TO 2.Gx.4PDA) if so, just flash the NVID then flash any 6.1 rom with LazyTool)
[size=+3]Tradition UPGRADE (OLD) method (for ROM with OS.nb )[/size].... ,
1. Connect to PC, activesync now OK, Flash with PVtemp or NVID for prophet for step 1
WHEN FINISH,
2. TOUCH NOTHING, HANDS-UP !!! leave it alone, just don't touch your prophet...... ( WM5 wwe flashing now finished)
3. [size=+2]ACTIVE SYNC WILL POPS UP soon, JUST DON'T TOUCH IT (disregard it) [/size],
4. THEN RUN UPGRADE.BAT from PC to flash to WM6 (should be included in your old ROM package with OS.nb )
5. follow the on screen steps and YOU WILL GET WHAT YOU HAD EXPECTED THEN~~~~~
[size=+2]PLEASE REPLY IF YOU THINK HELPFUL ABOUT THIS MESSAGE !! ^_^ [/size]
Click to expand...
Click to collapse
P.S.
dioxda2 said:
@VISTA FLASHING click HERE -- thanks to dear CLOUDYFA
@ Lazy_Tool + Cloudyfa's 19213 clean rom , simple, fast, error free, a 2 in 1 upgrade package
if error persists while upgrading with this tool,
Please ask yourself...
I. did I softreset yet? did I make the Prophet recovery? (remove battery and sim card),
II. will the USB port of my PC currently too heavy loaded?
III. did I restart my PC yet?
IV. any connection related software other than activesync is running?
V. did I try the rear panel USB ports?
VI. is my PC currently too busy?
VI. did I try other USB cable yet?
VII. did I try the force bootloader manually before upgrade?
VIII. Did I hardreset my prophet after new flash(if everything had done but no help~~~~ ) ^_^
IX. Is the battery problems?
if anyone found this useful, please submit a simple reply..........
Click to expand...
Click to collapse
all about dioxda2
~~~ What had happened to my first Prophet? pLEASE CLICK HERE
~~~All my cooked Prophet roms :
1d - Xtra Phrophet - 19214,
1b - U.C. Version - 19214,
1d - SPEED KING / Storm version - 19214 - Recommended!!,
2a - eXtreme PROPHET - 20270,
2d - ULTIMATE EDITION - 20270,
3d - Advanced version - 20273,
4d - with B/T Bug - 20275,
5d - buggy??? - 20721,
7d - THUNDER - 20748,
8d - eEXECUTIVE version - 20749 ,
9d - clean version - 20749,
1d - M2D-Lite - 20755,
1d- M2D 8Tabs version - 20755 - Recommended!!,
1d - m2d+mOtOsURF dual - 20755,
1d - SuperMarket version 1 - 20755 - Recommended!! for advance users,
1d CHINESE INPUT + M2D 7 tabs + 6 configurable iPHONE - 20755 - Recommended!!,
1d - cLEAN_tURtLE 1 & 2 - 20759 - for advance users only,
20755 - fINAL with iPhone?Today built - Recommended!!
WM6.5 - 1d - 21159 CLEAN n Fixed, for FUN,
WM6.5 CHS roms - 21806 / WM6.1 - 21127 for fun ,
WM6.5 CHS roms - 21222/21231/21502 for fun,
LAZYTOOL THREAD~~~
HardSPL could sometimes not 100% perfect, as my experience. My Prophet stuck at Tri-color screen once after flashing a WM6 Rom, and I had to flash the official WWE AKU 2.2 Rom with IPL/SPL to set it to work.
SoftSPL method is more reliable, IMO.
100% success in HardSPL upgrade......
ufriendxda said:
HardSPL could sometimes not 100% perfect, as my experience. My Prophet stuck at Tri-color screen once after flashing a WM6 Rom, and I had to flash the official WWE AKU 2.2 Rom with IPL/SPL to set it to work.
SoftSPL method is more reliable, IMO.
Click to expand...
Click to collapse
Please look here for reference..
1. if your device had been HardSPL successfully, the you can......
a. copy the 3 files ( in jumpspl.zip) to the root directory of the prophet
( JUST NEXT TO THE " \WINDOWS" FOLDER),
b. soft reset prophet,
c. run the SPL.lnk in the prophet,
d. then continue step 2 ( only 5 minutes..... finish.... so cool~~~~ )
100% success ~~~~
dioxda2 said:
Please look here for reference..
1. if your device had been HardSPL successfully, the you can......
a. copy the 3 files ( in jumpspl.zip) to the root directory of the prophet
( JUST NEXT TO THE " \WINDOWS" FOLDER),
b. soft reset prophet,
c. run the SPL.lnk in the prophet,
d. then continue step 2 ( only 5 minutes..... finish.... so cool~~~~ )
100% success ~~~~
Click to expand...
Click to collapse
I always do it like that...So quickly...
Why Why Why???
oko2600 said:
I always do it like that...So quickly...
Click to expand...
Click to collapse
yes, you are right....
By the way~~~~~
Why no one read this thread before one is posting or shouting for help????????
In fact, HardSPL isn't necessary to flash New WM6 Rom.
Just use SoftSPL, 100% OK.
haha ^_^
ufriendxda said:
In fact, HardSPL isn't necessary to flash New WM6 Rom.
Just use SoftSPL, 100% OK.
Click to expand...
Click to collapse
Not about the necessity but.....
Hard SPL takes 3.5 minutes to flash completely,
but the old method......... PVtemp + Upgrade = ~30minutes....
just about the efficiency and the convenience... ^_^
dioxda2 said:
Not about the necessity but.....
Hard SPL takes 3.5 minutes to flash completely,
but the old method......... PVtemp + Upgrade = ~30minutes....
just about the efficiency and the convenience... ^_^
Click to expand...
Click to collapse
Ok, let's put it in another way:
If our Prophet has IPL/SPL 2.××, just do SoftSPL before flash new WM6 Rom.
No need to flash HardSPL.
Is it not simple?
dioxda2 said:
I saw many people here suffering from such cases.....
...
...
...
you've better.... ( FOR NEW METHOD)
1. After flashing hardSPL for g3 ( step 1) all went ok.
then BEFORE flashing/upgrading your Prophet to WM6,
please copy the 3 files from the jumpspl.zip to the root directory of
your G3 Prophet ( JUST NEXT TO THE " \WINDOWS" FOLDER,
(attachached, pease unzip and copy then paste)
2. UNPLUG YOUR DEVICE from PC,
3. Execute the SPL shortcut IN THE DEVICE, then you see a all bright or white screen,
Then plug back the USB port ( connect to computer) the device, THEN use the Rom Upgrade Utility (RUU) to the rom you like ( all activities can only be seen in the PC screen, nothing will be shown on the prophet....
4. Finally, after 100% ( at 85% may take to wait a bit longer, just be
patient, as it may look like hang for about 2 minutes) just wait, all will went
ok AND OF COURSE, after it auto-restart, ALL will be OKOKOK !!!
( better hard-reset for once more )
I am using a G3 too. Same experience before... ^_^
no more prolems!!!!!
Click to expand...
Click to collapse
The attached jumspl file is broken "can you upload the file again.
Thank's in advance
???
trxerz said:
The attached jumspl file is broken "can you upload the file again.
Thank's in advance
Click to expand...
Click to collapse
Hey, the file works fine... just attached to this forum, not web
outside. I had tested it and download normal~~~
Please try again
ufriendxda said:
Ok, let's put it in another way:
If our Prophet has IPL/SPL 2.××, just do SoftSPL before flash new WM6 Rom.
No need to flash HardSPL.
Is it not simple?
Click to expand...
Click to collapse
But if you want to back to the original ROM you need HardSPL
trxerz said:
But if you want to back to the original ROM you need HardSPL
Click to expand...
Click to collapse
No, HardSPL is not needed to flash back to WM5 Rom.
Just put the Prophet into bootloader(Tri-color screen) and take RUU of WM5 Rom, will surely succeed, anytime.
How do you put spljump files to windows folder on the device when only the USB synchro mode (Red Green Blue screen) is displaying ?
Nothing work.
I've patched hardspl
Jumpspl too
but
I can't install Wm6 rom
always stay bootloader mode.
there is no gsm no radio
only shows IPL and SPL ( 2.00 / 2.15 )
I said......
EQUANCY said:
I've patched hardspl
Jumpspl too
but
I can't install Wm6 rom
always stay bootloader mode.
there is no gsm no radio
only shows IPL and SPL ( 2.00 / 2.15 )
Click to expand...
Click to collapse
Be patient!!
you must Hardspl sucessful ( SPL= 2.G3.4PDA .. something like this)
, or you cannot flash new methods,
please read through my content at the 1st page here....
or look to hma4 ......
I had made it easy for you... please folLow steps CAREFULLY
enjoy !!!
NO SHORTCUTS !!!!!
dioxda2 said:
Be patient!!
you must Hardspl sucessful ( SPL= 2.G3.4PDA .. something like this)
, or you cannot flash new methods,
please read through my content at the 1st page here....
or look to hma4 ......
I had made it easy for you... please folLow steps CAREFULLY
enjoy !!!
NO SHORTCUTS !!!!!
Click to expand...
Click to collapse
Yea, I must agree with Eqancy. Tried your method several times, the SPL says just what is should (2.G3.4PDA) but bootloader kicks in every time and nothing seems to work any longer.
Seems like I must be back to the old method.
Nothing works still same!
There is only SPL 2.15 not anymore
I've tried everything but
Results are same.
I've Wm6 before but it was slow and I want to change rom.
and I've read to threads for how to.
I had earlier IPL 1.0 only that but rom was G4 version.
and it was very slowly.
and I've upgraded spl to 2.20
but after this upgrade I can nothing to upgrade
only Qtek's 2.20.7.34_2.20.7114_02.19.21 rom.
I've upgraded/installed Hardspl ( GSM version appears on bootscreen and HTC logo but still waiting )
And after this upgrade.
I did jumpspl too but...
every things same.
I will try again again again...
thanks.
OKOKOK
EQUANCY said:
There is only SPL 2.15 not anymore
I've tried everything but
Results are same.
I've Wm6 before but it was slow and I want to change rom.
and I've read to threads for how to.
I had earlier IPL 1.0 only that but rom was G4 version.
and it was very slowly.
and I've upgraded spl to 2.20
but after this upgrade I can nothing to upgrade
only Qtek's 2.20.7.34_2.20.7114_02.19.21 rom.
I've upgraded/installed Hardspl ( GSM version appears on bootscreen and HTC logo but still waiting )
And after this upgrade.
I did jumpspl too but...
every things same.
I will try again again again...
thanks.
Click to expand...
Click to collapse
1. HARDspl OK,
2. then copy jumpSPL to the ROOT DIRECTORY OF PROPHET, NOT WINDOWS FOLDER,
3. UNPLUG PROPHET FROM PC,
4. RUN SPL.LNK IN THE PHROPHET,
5. PROPHET WILL WHITE SCREEN,
6. THEN PLUG usb TO A RESTARTED PC,
7. RUU UGPGRADE NEW ROM,
SHOULD WORK.....
dioxda2 said:
1. HARDspl OK,
2. then copy jumpSPL to the ROOT DIRECTORY OF PROPHET, NOT WINDOWS FOLDER,
3. UNPLUG PROPHET FROM PC,
4. RUN SPL.LNK IN THE PHROPHET,
5. PROPHET WILL WHITE SCREEN,
6. THEN PLUG usb TO A RESTARTED PC,
7. RUU UGPGRADE NEW ROM,
SHOULD WORK.....
Click to expand...
Click to collapse
Successfully done
Thanks
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
What is the IPL/SPL displayed?
Are you sure your device is a G4?
Try a hard reset.
Try this again: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
IPL 2.58.0001
SPL 2.58.0001
I'm sure that my device is g4. Did a hard reset and it went to bootloader again. Is there a hope? I will try http://wiki.xda-developers.com/index...ophet_recovery, but I noticed that when I run RUU and after verificatio informations on my pda it shows image version :_____________(blank),,then I click update,and then it shows
From:
image version :
To:
image version :
there is no numbers.
If you can enter bootloader, the device is recoverable.
HardSPL???
nikolah said:
I was trying to make upgrade from wm5 to wm6,and was looking in tutorial xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide. First,I found a Upgrade_HardSPL_G4.rar, and did what was said in tutorial,copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,Execute the SPL.lnk IN THE DEVICE, then you see Prophet in all bright or white screen,Execute the ROMUpdateUtility_NV_G4 (I have a g4 device) to upgrade hardspl. I got message that my update utility was old and that I need new. Then I restarted device,just run ROMUpdateUtility_NV_G4 from the hardspl folder and instalation went smooth,pda restarted and worked well. Then I went back on xda-developers > Prophet > Prophet mobile 6> New WM6 Upgrade Guide,found this sentence: ''Step 3 and 4 are necessary only if the WM6 rom you have downloaded instead of nk.nbf has os.nb file and the ExtROM folder'', and as I downloaded wm61_korand_3_1.rar that contains only nk.nbf file,I put it in Update_Package\Update Utilities,and run ROMUpdateUtility_NV_G4 fron that folder. The instalation finished and pda booted in bootloader. After that I tried flashing Shadow My Edition 2,no DualSIM,and followed the instructions to recover pda from wiki/ prophet recovery(downloaded PDAMobiz_Prophet_WM6_V1.00_Step1),everything was the same,always bootloader. Is there a help for my prophet? Could someone give me a step by step istruction how to bring it to life? Any help is welcome. Thanks
Click to expand...
Click to collapse
would you mind to read me thread?
dioxda2,I read your thread. and I will now try a other hardspl that you linked there. Was that the remark you wanted me to come to my notice?
Same Issue
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
there are sucessful cases , please read my post or.... are you using Vista?
If so, you need other solution. (not with me ... sorry ~~ )
georgexavier said:
I face the same issue.. have tried hard reset, hardSPL and downgrading to WM5 ROM.. only the downgrade is working.. but every time I try to upgrade to WM6 it enters RGB screen.. have tried with atleast 5 WM6 ROM... any senior member to help pls.
Click to expand...
Click to collapse
What is the SPL of your device?
When recovering to WM5 you better NOT use the Mobis step 1. Any other step 1 or NVID will be fine. The Mobis ROM is too manipulated for flashing their own WM6 ROM. It will give all kinds of problems when it is used for other purposes.
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
see my thread la~~~~
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
In bootloader, try to flash this: ftp://xda:[email protected]/RUU_Prophet_220734_2207114_024721_NVID.exe
nikolah said:
dioxda2,I have read your thread. This is what I know at the moment,and what I think it should be done (correct me if I make any mistake):
-my pda boots in bootloader mode
-it shows on screen IPL:2.58.0001, SPL:2.58.0001
-it's G4 model
-it has no hardspl on it
First one wild shot:
1. Download this jumpspl http://forum.xda-developers.com/showthread.php?t=329147
2.follow the instructions,and instead nk.nbf file from desired rom I put a nk.nbf file found in hardspl rar archive to the SoftSPL folder ,and hopefully flash hrdspl.
3.from bootloader flash any desired wm6 rom with RUU
Second solution:
1.download PVTemp
2.try to flash it from bootloader
3.if it's ok,then on to the next step like on your page one for old method.
Is there something else,diferent way to do this from bootloader?
Thanks for all help
Click to expand...
Click to collapse
Hi there ~~~~ tell you what~~ ^_^
1. there are 2 ways to upgrade
a. " New " Method.
b. " Old" method.
2. for more update rom flashing.... better have you device hardSPL.
then you can go by 3 means to flash....
1. straight upgrade that is: connect to PC via activesync, activate RUU right ahead ( I don't like this method as sometimes will stuck @ bootloader,
2. copy the 3 files from the jumpspl to the prophet's root directory then activate manually...
3. force bootloader ( by manually buttons combination and not reboot in 3 color hang )...
then 2 and 3 is fine, ( 3 is more convenience though), you should see " USB " at the bottom prophet screen if you did things right. ^_^,
then flash...... ^_^
This is my [size=+2]little handmade tool [/size], a combination tool with Taiwan Cook - YouZii and XDA cook - Korand,
just unzip, execute the " UPGRADE.cmd " , the some on screen clicks, wait and done. !!!
Don't forget to hardSPL before so. OK?
Enjoy ~~~
A Batch flashing tool and Korands clean rom 3.1... Check it out ! ^_^
P.S. Connection Error? Please try again ~~ ^_^
nikolah said:
I tried recovery with RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
and it reported error,saying that it's only for upgrade. Where to find NVID
Click to expand...
Click to collapse
You will find it here:
ftp://ftp.xda-developers.com/Uploads/Prophet/Prophet-roms/
Hi guys,
I need your help. You'd make me amazingly happy if you could solve my problem.
I have an Orange SPV C100 (french one) and I keep trying to flash wm6.1 (the one Blackdragon_860 has released).
My problem is : I can't flash that rom. The updating process crash at 4% and I get an error saying that the ROM is corrupted.
Do you have any ideas to help me ?
Here are some additional information taken from the Hard-SPL And Soft-Spl walktrough :
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
Click to expand...
Click to collapse
I've done that alright
, hold camera and launch spl.lnk -
Click to expand...
Click to collapse
I've done that too.
you`ll see the white screen
Click to expand...
Click to collapse
I have no white screen. Instead a file named JumpSPL.txt is generated... Here is what is inside :
-----------------------
Comandline is: 0x10000000 \SPL.nb
SPL File: \SPL.nb
Jump Address: 0x10000000
kmode is 0
SPL file size: 524288 bytes
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
Click to expand...
Click to collapse
I've done that too. I put RUU_Signed.nbh from wm61OxygenUpdate1.rar in the same directory than ROMUpdateUtility.exe
Before the flashing process itself, ROMUpdateUtility.exe tell me I going to flash the image version from 1.7.74.1 to : 1.01
Then I have a rainbow screen which says :
ONBL : 1.07.0000
SPL : 1.07.0000
Oxygen : IU
The flashing process start, then crash and 4%... Saying that image file corrupted.
One last information :
I got the same error with other ROMS. Here the list of what I already tried :
Blackdragon_860's rom, released the 11-05-2008
Standard rom, the one that comes with Soft and Hard SPL (weight about 641Ko)
A Russian rom, taken today from zfree (here)
I didn't tried the chinese one. But as edgeofthestring has eventually the same problem than mine, I not will go for this rom.
I tried to be as complete as possible... I truely need some help.
Plz plz plz hrlp.
Thx
Guigoui
Try first flashing this rom:
http://www.megaupload.com/nl/?d=6B0FDY24
After this hard-spl and than flash any rom you like
Always use rom loader from hard-spl and before flashing rename rom to RUU_Signed.nbh
i also tried to flash the file posted by you but after 4 % the phone reboots and the setup gives me the: " invaliv vendor id " message
Default
ok. may it works when you do it like this:
1. restart your phone
2. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device
3. restart phone, don't connect to your PC!
4. open total commander, hold camera button and launch spl.lnk
5. Do you see a white screen? if yes proceed if not it has no
point proceeding, flashing will fail anyway!
6. Now connect your phone to your pc using the usb cable
7. From the flasher folder run ROMUpdateUtility.exe and follow
instructions to flash the Hard-SPL
8. After flashing Hard-Spl, to avoid reflashing, use always use
flasher from hard spl and rename the desired rom to flash to
RUU_signed.nbh
Hope this will finaly work for you!
i have tried it, i have the wm6.1 chinese version rom and the hard spl is not working at all in this rom, i have tried it with total commander and after the white screen appears and i connect the phone to the pc it is nor recognized by the pc...
thx nemphis for helping me... but it just don't work.
Believe me I'm not numb. I can read and use my little brain... I think I tried everything (including throwing my device to the other side of my room). There is something that keep my device from displaying this f*****g white screen.
Just for the record, I repeat, I have a french blocked orange C100...
If someone has got in the same problem and finally sorted it out, plz share how.
Nemphis, thx again but I doubt I will ever have wm6.1... Anyway I give up, so I guess I will never have wm6.1...
By the way, I also tried the rom you advised but as you so rightly said "if not it has no point proceeding, flashing will fail anyway!".
Thx you all...
c u...
by by
Is your phone sim unlocked also?
When reading through these forums there also are people saying you still need this: http://www.imei-check.co.uk/
Or ask your operator for the sim unlock code, they should give it when your phone is more than 1 year old.....
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
guigoui said:
Phone simunlocked today... gonna try again tonight... Hope it will eventually work this time... Last hope anyway...
Click to expand...
Click to collapse
Was your phone "app unlocked" before begining ? I would assume it is necessary, but won't pretend I'm a guru...
Christophe - Lyon - France
@guigoui :
I had this same, white screen didnt appeared .. but after unlocking using this way: http://rapidshare.com/files/105133496/Unlock_HTC.rar.html you'll see it (after runing SPL.lnk with camera button pressed) all is working !!!
I've WM6.1 !!!
Thanks!
This sounds pretty good vovakk... I'll test your file tonight (because I had no white screen after having my device simunlocked)
I can't to stand waiting until tonight...
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
hey GuiGoui can you upload this file here or Rapidshare please. Megaupload is way tooooo slow. RUU_OxygenWM5_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test.exe
thanks
I can't.... 8Mo limited...
guigoui said:
It WORKED !!!! Now I have WM6.1 !!!
Ok so here are some additional information that could be useful.
Be sure you have .net framework 2.0 or newer before starting the unlocking process (the file shared shared by vovakk) otherwise you would be stuck at the second step.
When at step 5, I'm not sure which profile is required but, for me, it worked with "No security".
Once you've done step 5, you'll get THE white screen when laucnhing SPL.Ink (I confirm). You can start flashing.
I've flashed several rom as nemphis told me to, and it worked. Here is the list in the right order, with some notes :
1. http://www.megaupload.com/nl/?d=6B0FDY24 (given by nemhpis) : takes about 2-3 minutes, when done, I believed that my device was dead because it took a while before the PIN screen showed. Don't panic, just wait.
2. http://rapidshare.com/files/65732449/hspl.7z.html (the original Hard-Soft SPL - created by sp3dev) : extract, don't change anything, just launch RomUpdateUtility.exe. Flashing process takes less than 1 second
3. http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar (THE Windows Mobile 6.1) : In the RomUpdateUtility.exe folder, just replace the original NUU_signed.nbh by the one inside wm61OxygenUpdate1.rar. Launch RomUpdateUtility.exe. Eveything else is like 1. except that my device rebooted fast without being stuck a while on the windows mobile logo screen. The device reboot, you enter your PIN and then welcome to WM6.1 !
Hope someone would find interesting to read my so long posts...
I thank you all for your patience and help... I wouldn't be able to do it by myself.
C you
Click to expand...
Click to collapse
How did it work............ i ended up lockin my phone it was unlocked before... now no application works... anymore it say this application is not have signed certificates..... PLZ ANY1 HELP I DONT EVEN KNOW HOW TO HARD BOOT THIS HANDSET..... I NEED URGENT HELP PLZZZZZZZZZZZZZ...
Ive got a "bricked" S200 G4 (I think)
Text in rainbow screen is
"ILP 2.20.0001
SLP 2.10.0001"
I dont know if the difference here matters.
Tried to upgrade with different ROMs, but no luck, upgrade stops in the process, different % every time.
But the latest Speedking 2 ROM I managed to install. Hopefully I softbooted and got the same rainbow screen.
Any advice?
Why didn't you hardspl your prophet ??
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
hpn said:
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
Click to expand...
Click to collapse
1. not 100% of our Prophet can be hardspl done ( like mine )
2. if so, just go straight ahean with my lazt_tool, too easy though....
3. hardspl is just a flashing process but only spend a couple of minutes unlike rom flashing, (from 5 - 10 minute.)
all you have to read in the sticky post on the top pf this forum
I recommend youto read post 1 of this thread....
http://forum.xda-developers.com/showthread.php?t=353547 as follow....
20080601added:
[size=+2]Lazy_Tool (thks YOUZII) is for flashing all nk.nbf, in win-xp PCs, ........[/size]
WANNA GO OLDER ROMS? READ THIS POST THOROUGHLY ^_^ )
P.S. You can just change / replace the nk.nbf inside the Lazy_Tool folder if you wish to flash other roms....
20080529 added:
Cloudyfa's 19213 clean rom + Lazy_Tool, simple, fast, error free, a new upgrade tool.
[size=+3] Additional RECOVERY steps for 3 colors screen boot-up after flashing...[/size]
a. Force Bootloader Mode MANUALLY (see below Point 4 for How To ), Then flash PVtemp or NVID for prophet( P.S. the boot up screen will be changed to Qtek...),
b. ( Optional) Use Lazy_Tool to upgrade to WM6.1 (default rom is Cloudyfa's 19213-clean, you may change if you want...)....^_^,
Click to expand...
Click to collapse
20080423 added: Alternative "Lazy_Tool"
some hints ~~
if error persists while upgrading with this tool,
Please ask yourself...
I. did I softreset yet? did I make the Prophet recovery? (remove battery and sim card),
II. will the USB port of my PC currently too heavy loaded?
III. did I restart my PC yet?
IV. any connection related software other than activesync is running?
V. did I try the rear panel USB ports?
V.I is my PC currently too busy?
VI. did I try other USB cable yet?
VII. did I try the force bootloader manually before upgrade?
VIII. Did I hardreset my prophet after new flash(if everything had done but no help~~~~ ) ^_^
**************************************
2008-02-18 added ***
NVID for prophet,
Click to expand...
Click to collapse
HARDspl
(OLD method is at the bottom of this post)
1: "DON'T PANIC",
2: 99.9999% CAN BE RECOVERED BY
DOWNGRADE TO WM5 WITH entering BOOT_LOADER MODE + flashing the PVtemp (old method step 1).
3: IF USB CONNECTION ERRORS, TRY REMOVE BATTERY FOR 1 MINUTE and try again.
4: FORCE BOOTLOADER MODE MANUALLY HOW TO = ....
4a. keep pressing the Commgr button and
4b. in the same time keep picking/sticking the bottom softreset button with stylus for one second,
4c. [size=+2][highlight] THEN ONLY ONLY RELEASE THE STYLUS[/highlight][/size] and wait for the screen
TO CHANGE to the three color screen (bootloader mode),
4d. then release all and go to step 10 below..... !!!
Click to expand...
Click to collapse
(remember to download and prepare all files you needed first, or you may have errors while in the upgrade process)
Click to expand...
Click to collapse
5. Execute the Rom Upgrade Utility (ROMUpdateUtility_NV_G3.exe ( or G4), in the
HardSPL folder that you had downloaded, all activities will only take 2-3 minutes to go and
nothing will be seen in the Prophet screen.
(P.S. if connection Error, NO PANIC, soft reset OR remove battery for half a minute and try again. )
6. after the flash completed, it will restart automatically.
7. done!! in your prophet, nothing will be changed VISIBLY EXCEPT the digits IN the reboot screen !!!!!
and while booting now YOU MUSTBE ABLE TO SEE information like: 2.G3.4PDA (FOR G3 PROPHET) or 2.G4.4PDA (FOR G4 PROPHET)
Prophet Hard SPL isn't yet completed until the SPL shows
"2.G3.4PDA" or "2.G4.4PDA". ^_^ !!!
Alternate way to Flashing / upgrading your Prophet to WM6,
a. ENTER BOOTLOADER (see how to at the upper part of this post) [size=+2]OR [/size]
b. DO THE JUMPSPL...(step 8-9 BELOW) [size=+2](you can force to bootloader mode instead of step 8 to 9)[/size]
8. copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,
9. Execute the SPL.lnk IN THE DEVICE (using the Total Commander is recommended), then you see Prophet in all bright or white screen,
10. Plug back to the USB port ( connect to rear USB panel of the computer - recommended) to the device,
11. Execute the Rom Upgrade Utility to upgrade to your chosen rom
(or put your NK.NBF to the unzipped WM6_Update_Utility folder), all activities will
only take 3-5 minutes, nothing will be seen in the Prophet screen.
12. Finally, after 100%, be patient, just wait, and Prophet will reboot automatically.
13. OF COURSE, after it auto-restart, [size=+2]better one more time HARD-RESET[/size],
ALL will be OKOKOK !!!
[size=+3]Tradition (OLD) method[/size].... (for ROM with OS.nb ),
1. Connect to PC, activesync now OK, Flash with [size=+2]PVtemp[/size] or NVID for prophet for step 1
WHEN FINISH,
2. TOUCH NOTHING, HANDS-UP !!! leave it alone, just don't touch your prophet...... ( WM5 wwe flashing now finished)
3. [size=+2]ACTIVE SYNC WILL POPS UP soon, JUST DON'T TOUCH IT (disregard it) [/size],
4. THEN RUN UPGRADE.BAT from PC to flash to WM6 (should be included in your old ROM package with OS.nb )
5. follow the on screen steps and YOU WILL GET WHAT YOU HAD EXPECTED THEN~~~~~
[size=+2]PLEASE REPLY IF YOU THINK HELPFUL ABOUT THIS MESSAGE !! ^_^ [/size]
Click to expand...
Click to collapse
I`m running Mac, with XP under Parallels. Upgrading Trinity is no problem on his config. But your reciepe include running command window. I cannot connect to the prophet from command window.
Trying to solve this somehow. Thanks for the link.
Hy to all, first of all thank to everyone that put time and pacience in this hobby. I want to anticipate that I've been hours to search an answer before posting, but my result was not good for me. I hope that someone tells me I'm stupid and I can find my solution in that thread (this means I'm quite close to the end of my problem).
History
X7500 upgraded to HTC 6.0 original rom
unlocked my athena with olipro unlocker (thanks to olipro) to 1.20 (from 1.10).
upgraded my radio from 1.50 to 1.58.
flashed my rom with micky's 6.1 italian rom.
I had problem with language: italian rom appeared me as english and I couldn't change to italian.
I decide to go to michy's italian rom page and download 1.15 rom.
from another computer now I try to change my rom but............
after starting the bootloading (spb 1.20 olipro appears so it's unlocked) the device disconnect from activesync and usb and no upgrade is possible. It appears me the request for new hardware information driver needed (as my pc doesn't recognize athena in bootloader mode). So... no connection and no upgrade. I've tried to launch other upgrades (rom and unlocker) but still the same. Where am I wrong? is it something related to the pc or to the athena? thanks in advance to whom will answer me.
so? 70 readers a noone that write try this ot that?
Woow!!!
I normally use SDcard to flash because the usb port on my unit is not detected properly. Since you already have SPL 1.20-Olipro, you can easily revive yours.
Just follow these steps:
1 - format your SDcard with FAT32 (use windows explorer on your PC)
2 - extract any wm6/6.1 spl 1.xx rom you want to flash and copy all files into your SDcard
3 - rename the RUU_signed.nbh to atheimg.nbh
4 - put the SDcard into your unit and boot the device into bootloader mode (or you can simply click Enterbootloader.exe if you can use file explorer on the device)
5 - after you finish flashing and the screen shows 'Restore OK' .. remove SDcard first before you reset the device. Sometimes need to plug out the battery or reset twice or do hard reset before the unit will boot again into OS.