Related
Hi to all,
please help me,
When i wana install the last atom exec rom,two days ago,everythings is ok,but after hard reset,my device stayed at O2 logo and I couldn't hard reset my device and install rom too,because didn't sync with my laptop,have you any idea for this problem?
take off the battery and try again
I take off the battry many time,but this problem exist yet.
can you enter in bootloader mode (camera + reset) ?
yes,but i see a black screen that written on it:sd detected and
"starting download ...
sdDownload:couldn't find file;diskimg.nb0;.
sdDownload:couldn't find file;eboot.nb0,.
sdDownload:couldn't find file;dm.nb0,.
..."
at the end of screen:
"SD trensfer completed."
what your idea?what things i must to do?
Once entered in bootloader mode (ignore these SDCard messages), plug de USB cable and wait the device to be detected by windows
you'll be able to upgrade a new rom
i have the same problems, i upgrade the phone still stay on o2 logo
any other solution??
thanks
have you follow the upgrade procedure correctly?
just an opinion...
remove sd card...
then enter bootloader
then run upgrade DSUU.... follow on screen instruction
should be ok to upgrade your rom...
1. remove SD Card
2. remove battery
3. hold camera button and reset (stylus) button
4. replace battery while still holding the buttons
This will bring you back to bootloader mode. Just flash the above DSUU.
DUN USE MEMORY CARD TO FLASH AGAIN!!!
joncy said:
just an opinion...
remove sd card...
then enter bootloader
then run upgrade DSUU.... follow on screen instruction
should be ok to upgrade your rom...
Click to expand...
Click to collapse
There is no SD card in the phone. the upgrades is went well 100% flashed in.
But the phone still stuck on startup O2 LOgo.
any idea??
BR
mphoneclinic said:
There is no SD card in the phone. the upgrades is went well 100% flashed in.
But the phone still stuck on startup O2 LOgo.
any idea??
BR
Click to expand...
Click to collapse
what ROM version that you used?
think better for you to downgrade to ORIGINAL WM5 ROM. since ATOM EXEC used the MN2 bootloader you will not able to update you rom via bootloader mode. BUT I will share my experience on my ATOM EXEC when my device in unable to boot condition.
1. you need to downgrade your bootloader to MN1 type (ATOM Standard bootloader), copy the EBOOT.nb to your SD card
2. prees camera+reset --> you will see the bootloader found and update, and device turn off
3. TAKE OUT SD CARD !!
4. take out your battery, press CAMERA+RESET and plug in back your battery, you should come back to bootloader mode again (now you should have MN1 bootloader on your ATOM EXEC)
5. Run Xda-Atom-Exec-ENG-20060721-MOT0822.exe, the ROM will be intalled on bootloader mode BUT will be stack 6% on EXTENDED ROM
6. when 6% (progress bar not move anymore) just take out your USB cable from your ATOM --> on this stage you already upgrade ROM + bootloader(MN2) just the EXT ROM failed to update
7. turn on your device, you will able to enter to WM5 but the job not finish yet.
8. run one more time Xda-Atom-Exec-ENG-20060721-MOT0822.exe on DSUU mode, viola after completed the progress your device will be back on ORIGINAL WM5.
note: please read step by step, if you don't understand than better DON'T DO IT, send to service center will be good choice otherwise your ATOM EXEC can really become paper weight!
chartreux said:
1. you need to downgrade your bootloader to MN1 type (ATOM Standard bootloader), copy the EBOOT.nb to your SD card
2. prees camera+reset --> you will see the bootloader found and update, and device turn off
Click to expand...
Click to collapse
What can we do if the bootloader don't start ?
it is possible to modify eboot without bootloader ?
Thanks a lot.
bedav said:
What can we do if the bootloader don't start ?
it is possible to modify eboot without bootloader ?
Thanks a lot.
Click to expand...
Click to collapse
I don't think so, if your device can not be turn on via bootloader mode, then the bootloader corrupted on your device. the key is to secure the bootloader partition. without that one will be useless
for those who cant get pass the "Hard-Soft SPL - created by sp3dev",
1- You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone.
2- Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3- Download http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar and upgrade your phone using the Flasher included in the file you downloaded in step 2.
I did mine, and now I have wm6.1 installed in my phone. and I loved it.
Thank you all for your input
charlietruong said:
for those who cant get pass the "Hard-Soft SPL - created by sp3dev",
1- You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone.
2- Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3- Download http://rapidshare.com/files/114457795/wm61OxygenUpdate1.rar and upgrade your phone using the Flasher included in the file you downloaded in step 2.
I did mine, and now I have wm6.1 installed in my phone. and I loved it.
Thank you all for your input
Click to expand...
Click to collapse
how the software unlock?
Copy all 3 files you downloaded in step #1 to your Oxygen. Then execute all 3 files in numerical order.
Good luck!
charlietruong said:
Copy all 3 files you downloaded in step #1 to your Oxygen. Then execute all 3 files in numerical order.
Good luck!
Click to expand...
Click to collapse
sotty after the white screen when i connect my smartphone to my pc nothing happens and activesync says no connection
it's ok. when you see the white screen and after you plug it in the computer, wait about 10 seconds then start upgrading.
charlietruong said:
it's ok. when you see the white screen and after you plug it in the computer, wait about 10 seconds then start upgrading.
Click to expand...
Click to collapse
oh yes I am successful
colataroc said:
oh yes I am successful
Click to expand...
Click to collapse
Hi,
would you please show me how you did it. My phone can only go in bootloader mode, like yours was. Please help. Thanks
traiviet said:
Hi,
would you please show me how you did it. My phone can only go in bootloader mode, like yours was. Please help. Thanks
Click to expand...
Click to collapse
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Thank you, but I can only get to the bootloader mode. I can't get pass the Windows Mobile screen.
traiviet said:
Thank you, but I can only get to the bootloader mode. I can't get pass the Windows Mobile screen.
Click to expand...
Click to collapse
oh i'm sotty but for this i don't know. i think you have already read this : http://forum.xda-developers.com/showthread.php?p=2186022
To fix your phone if its in the bootloader download this rom:
http://www.leaf.co.za/downloads/ROMS/Oxygen/Oxygen%20-%20P%20N%2099HCD064%20-%2024%20January%202007.exe
And flash it to your phone. It will then boot up in WM5.
This ROM has English and Russian.
Mavix_2008 said:
To fix your phone if its in the bootloader download this rom:
http://www.leaf.co.za/downloads/ROMS/Oxygen/Oxygen%20-%20P%20N%2099HCD064%20-%2024%20January%202007.exe
And flash it to your phone. It will then boot up in WM5.
This ROM has English and Russian.
Click to expand...
Click to collapse
thank you. i will try now. you'd be my life saver if it works. I'll let you know as soon as i try to reflash my phone.
hi Mavix_2008
i tried flashing this rom but it didnt work. it just reset at 4% and says Invalid vender ID. I dont know whats wrong with my phone.
Thx for all, i success =)=)=)
SIM unlock
I tried you procedure but I was blocked by an error message saying "no application associated to spl".
I could not launch spl.lnk
Could some one help me to resolve this.
Thanks
Anzad
SIM unlock
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Hello,
I Tried your procedure in order to update my WM and then unlock my mobile but I was blocked by an error message saying "No application associated de spl". I could not run spl.lnk
Could you help me please
Thanks
Anzad
Hi,
I installed the HTC.Device.Software.Unlock.
I copied the 3 files spl.nb, spl.lnk and jumpspl.exe...I hold the camera button at the spl.lnk...I wait...1 minute...2minutes...but nothing happens.
I just have to hold the camera button or I have to open the spl.lnk too?
Could you please help me?
Thank you
Hi,
I'm interested for this ROM
But is it in French too?
Thanks for respons
Bye
A debutant...
Great succes!!
colataroc said:
but you can only enter in bootloader then the system doesn't starts, does it?
however if you can access to the system you will have to do like this
1) You'd have to download this file HTC.Device.Software.Unlock.zip and Appl Unlock your phone (copy the three files from the folder where you have extracted the archive to the root of your phone; then run the files in numerical order)
2) Download hspl.7z and Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen.
3) Connect the USB cableto the PC. (when you plug the phone, the pc will install other drivers)
4) In the hspl folder you have another folder named flasher. From the flasher folder run ROMUpdateUtility.exe and follow the instructions to flash Hard-SPL on your phone. After this step your phone will restart itself and you'll be able to install any ROM ( the instructions to flash Hard-SPL on your phone say that you have to estabilish an activesync connection with your pc but if doesn't happen go forward; the important thing is that your pc have installed other drivers)
5)Now take the file RUU_signed.nbh[40.1Mb] which you previously downloaded and copy it to the folder flasher over the one that is already there.(http://rapidshare.com/files/115494795/RUU_signed.7z)
6)With your phone connected to the PC through the USB cable run from the folder flasher ROMUpdateUtility.exe and follow the on-screen instructions to install WM6.1. NOW YOU HAVE WINDOWS MOBILE 6
Click to expand...
Click to collapse
Thanks a lot for the great explanation! My first time on this forum, my first steps in modding my phone, instant succes!
Greets from a newb...
klaasroelofs said:
Thanks a lot for the great explanation! My first time on this forum, my first steps in modding my phone, instant succes!
Greets from a newb...
Click to expand...
Click to collapse
Do you have manualy lauched the spl.lnk or when you hold the camera button it launch automatically?
I have a T-Mobile MDA Vario II and it just seems that flashing is impossible. I am pulling my hair out!
I have searched the forum and cannot see anyone else having had the same problem
I have tried to flash WM6, as provided by T-Mobile and also I have tried to flash Hard-SPL, but get the same problems with both.
First of all, if I try to flash by flashing from the PC, via ActiveSync, it all seems to be fine until it comes to that actual flashing itself. As soon as the flashing process begins, the phone goes to the bootloader and disconnects from ActiveSync, producing an error message in the program on the PC.
I have tried doing it directly on the phone, as described in post 1160 of the Hard-SPL, Or How to Not Brick Your PDA Ever Again And Fix Bad Blocks! thread, but when I reach step 7, where it should go from the tri-color screen to another screen, asking you to press the power button to start, it doesn't happen! The tri-color screen appears, followed, for less than a second, by a screen which says "Loading..." and then it just goes back to the bootloader screen, where it stays until I do a reset.
Anyone got any ideas at all?
CID Unlock the device then try to flash it, make sure battery is fully charged too. Have you tried entering bootloader manually then trying to flash the tmobile rom?
It won't even let me do that!
I have just tried to do this, using pof's free HTC Hermes SIM & CID Unlocker but even that won't work.
Pof's zip file contains 3 methods of doing this. I'll list all 3, with a description of where it goes wrong each time. Perhaps that will make the problem clearer
Easy auto-install Instructions:
-------------------------------
1. Unzip unlocker and run AUTO_Unlock_v3a.bat
2. Follow directions on screen
The .bat file starts a program on the PC. It goes OK, until it sends the phone to the boot loader screen. ActiveSync immediately disconnects and an error message comes up on the PC...
ERROR [260]: CONNECTION
The Update Utility cannot connect to your PDA Phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone
Check the following:
1. The PDA Phone is connected to the USB cradle/cable
The USB cradle/cable is connected to the PC
Click 'Exit' to quit
manual instructions:
---------------------------------------------------------------------
1. Transfer SSPL/SSPL-HERM.exe to your phone and run it
2. Tri color screen will appear
3. Disable activesync (file -> connection settings -> uncheck "allow USB connections")
4. Connect your phone to your computer using the USB lead.
As long as the Tri-color screen is showing, the PC does not recognise the PDA Phone as being connected, even if the USB is connected
5. run RUU/RUU_HERM_Unlock_v3a.exe
6. follow the flashing process (Check the "I understand..." and "I completed..." boxes and update!)
Rather unsurprisingly, the same error as above appears
7. Allow your phone to reboot.
8. Transfer HERM_Unlock_v3.exe program to your phone and run it
9. Click the Unlock Button, select unlock option. Select if you want SIM/CID unlock.
10. Click "Unlock!" and wait until process finishes.
11. When done, turn off your phone for 10 seconds and reboot after that.
I actually still went through steps 7 to 11 and it all seemed to work, but although it said the PDA Phone was now SuperCID, it wasn't
update using the SD-Card Method:
-------------------------------------------------------------------------------------
1. Unrar RUU_HERM_Unlock_v3a.exe
2. Unrar RUU_Inside.exe This file doesn't exist in the zip file
3. Empty (erase the contents) of your microSD card from the Windows Mobile file explorer
or format it from your computer using a card reader (in some cases format doesn't work).
4. Rename HermesUnlocker_v3a.nbh to HERMIMG.nbh and copy it to the FAT32 formatted microSD card.
5. Insert microSD card on your phone
6. Transfer SSPL/SSPL-HERM.exe to your phone and run it
7. Confirm flashing on screen by pressing the power button. Nothing to confirm. The phone simply goes straight to the Tri-color screen and stays there until you do a soft reset
Again, I don't know how much help it is, but if I go to the boot loader screen, via the power, OK and soft resent buttons, I see the following information...
HERM300
IPL-1.01
HERM300
SPL-1.04
If I run the SSPL-HERM program on the phone, it takes me to the boot loader screen, but with the following info...
HERM300
HERM-SSPL by des
HERM300
SPL-1.09.ds
Any ideas?
Go to bootloader and tell us what your SPL is... If its 2.10 olipro then you have Hard SPL installed. This process is VERY quick so it may have worked and you just didn't notice the change.
As for using the PC & Activesync, if you have Hard SPl, use the sd card method to load new OS's onto your Phone instead as its safer and easier (same as how you loaded Hard SPL except you don't need to run the SSPL program from your device, just put file on card, rename and reset to bootloader.
Cheers...
That info is in the prevoius post. Before you worry that you are going mad, I edited the message to add that info, so I guess you probably asked, before that info was there
Hello.
I tried to update with the ROM from SD card, but it failed.
My phone doesn't boot after that - it hangs up showing just splashscreen and some info -
ONBL 1.07.0000
SPL 1.10.0lip
GSM 02.71.90
OS 1.8.0.0
Hard reset didn't help.
I tried to flash ROM through RUU (device still goes into bootloader by pressing camera+reset/power), but it said
ERROR [200]: Invlid Update Utility
Please get newer Update Utility
Is there any way to flash my device? =\
btw, sorry for my english, i know that it's quite bad )
You need to first patch your HSPL and then flash a custom ROM.kindly read the ROM Upgrading Guide properly in the GENE forum.you can also find the link in my signature.
karan999 said:
You need to first patch your HSPL and then flash a custom ROM.kindly read the ROM Upgrading Guide properly in the GENE forum.you can also find the link in my signature.
Click to expand...
Click to collapse
If you are talking about that method -
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Click to expand...
Click to collapse
then it didn't work.
Mtty connects to the phone, it even says that bootlader patched, enters the "White screen" but RUU that is situated in the "Orefkov" folder says still the same: ERROR [200]: Invalid Update Tool
And btw, Orefkov method is for new gene only, am i right?
And I have an old one. And it's already have 1.10.0lip SPL, that allows custom ROM flashing.
LordOfFrost said:
And btw, Orefkov method is for new gene only, am i right?
And I have an old one. And it's already have 1.10.0lip SPL, that allows custom ROM flashing.
Click to expand...
Click to collapse
ya..Your SPL is patched and u have old gene
Now u can Flash Any custom rom from here(just No stock roms)
Problem was solved by deliting Active Sync, cleaning registry with CCcleaner and installing Active Sync after that...
I think that there was some driver problem or smthng >_<
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
bluffmaster said:
Hi,
Customer Bring Me Bricked Gene(Dead Condition)
Its Only Go To Boot Loader Mode and also detactable
(USB Icon Show When Enter Cable)
Here is the Details.
ONBL 1.07.0000
SPL 1.10.Olip
Serial Number Start with 8XX
When I Would Like To Update Rom With Rom Update Utiliy This Error Appear.
p3400 error 300 invalid update tool
How To Solve This Problem ?
Is My Genie is Old?
Rgds
Bluffmaster
Click to expand...
Click to collapse
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
karan999 said:
Go through the Rom upgrading guide.Read thoroughly and follow every step carefully.there is a difference between Old Gene and New Gene.You will learn as you follow the guide as to which one is yours.Also to avoid invalid update tool errors,make sure your device is properly synced to yur computer.In your cas as the device is fully dead.Perform a Hard Reset.Even if that doesnt work,you have to use JTAG method to get back your Gene.
So follow the Guide and you'll do good.Revert back when your problem is solved.And do not Create New Threads unnecessarily.Post your doubts in the respective threads.
Click to expand...
Click to collapse
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
bluffmaster said:
Hi
I follow the guide and Upgrade my SPL Olipro to Orefkov's.
PHP:
Step 5: Use the Orefkov Unlocker
------------------------------------
1. Remove the battery, SIM card and SD Card of your phone and press the Power key for 20 seconds to draw out any residual power from the phone.
2. Replace the battery but not the SIM and SD card, and don't start the phone yet. Press and hold the Camera button and then press the Power button or Soft Reset button. Phone will come to boot loader mode (tricolor screen) and SPL 1.10.Olip will be displayed.
3. Connect the USB cable. The text USB will appear on the bottom of the screen.
4. On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
Code:
ls boot.bin
Note : that is small L and small s in that command, dont mistake it with I.
Now, hold down the Camera button on phone, and press the enter key on computer. After a while, the screen will become White. Continue pressing the Camera button for 10 more seconds.
7. Now release the camera button, close the MTTY program and run ROMUpdateUtility.exe in the same folder, not the one outside it. That one is for RAM flashing that we will use later. Check the boxes in each step and click Next Next and then at last Update. Let it finish the process. Your phone will restart.
8. Now on the splash screen you'll see the info with updated SPL version. The version of SPL will be 1.07.Oref.
Congrats! you have successfully patched your SPL.
Step 5 of Guide is Goes Well....
But Guide Show in Step 6 phone boot Once
PHP:
Step 6: Flash the ROM
---------------------------
Now let the phone boot once and then shutdown it. Insert your SIM card, but not the SD card. Go to the PC and copy the ROM file (it must be names RUU_Signed.nbh. Rename it if it has some other name.) into the ROM Update Utility folder that is outside the Orefkov and SPL Patcher folder.
Now press and hold the camera button and start your phone to go into the Boot loader mode once again.
Now Run the RomUpdateUtility.exe and follow her instructions. Please make sure that you are not running RomUpdateUtility inside the Orefkov folder in SPL Updater folder. You must use the one outside, in the RomUpdateUtility folder. Your phone will automatically go into bootloader mode and a progress bar will be displayed on both phone and PC. Once it completes, your phone will restart again and you'll get the phone with the brand new ROM.
But Mine is Still Dead When i Press Power Button only redlight blink.
also it can go to bootloader when i press power + camera key.
i have sucessfully update my rom but now phone still dead
rgds
bluffmaster
Click to expand...
Click to collapse
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
mr.harsh said:
Make sure that you have removed SIM card and Storage card and try to connect it again.Then run mtty1_42.exe and select USB in the port then press OK.Hope this will help you.
Click to expand...
Click to collapse
I already remove my sim & storage card but now i can not switch on my phone / When i Press Power Button only redlight blink. also it can go to bootloader when i press power + camera key.
gcpganesh said:
Hi Friend i have the same problem
I successfully go to the (3. Connect the USB cable. The text USB will appear on the bottom of the screen.) after that when touch the usb text on my mobile it not responding & the Mtty1_42.exe programe the window will open but i cannot write any thing. please help me .
Click to expand...
Click to collapse
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
HLCMAD said:
good morming
On PC, go to the folder Orefkov in the folder extracted in step 1 and run the Mtty1_42.exe. Press the button "USB" in the window that opened.
5. In the window that opened, type the following command (don't use copy paste please) and press enter:
Code:
set 32 1
You'll see a response from phone.
6. Type the following command BUT DON'T PRESS ENTER YET:
it don´t apear any window after run mttyy1_42. Open a program bu i don´t see any button USB!!!
Cam you help me??
Thanks
Click to expand...
Click to collapse
Thank u friend
when i chose USB button of mobile it is not responding & I can not write any thing in mttyy1_42 programe.
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Hakim Rahman said:
to be able to do the command in the MTTY programe, for the first you should disable activesync -> connection settings -> uncheck "allow USB connections"
Click to expand...
Click to collapse
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
gcpganesh said:
Thank you friend i already done it, when conect the phone to computer through USB ,In a corner position of the phone USB is written, but when i open the MTTY program it open & shows the Port option to chose , but it is not showing the USB option in that option.
Click to expand...
Click to collapse
If it does not exist, You can add it by typing USB on port column option
Hakim Rahman said:
If it does not exist, You can add it by typing USB on port column option
Click to expand...
Click to collapse
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
gcpganesh said:
Thank U,
I add it but i got this " \\.\WCEUSBSH001 port can not open" Error Message.
(If Any thing i have to do after connecting USB Cable to phone to PC)
Click to expand...
Click to collapse
You've kill processes wcescomm.exe on Task Manager ??
Hakim Rahman said:
You've kill processes wcescomm.exe on Task Manager ??
Click to expand...
Click to collapse
Thank u Friend
Now how can i update 6 professional to 6.5
gcpganesh said:
Thank u Friend
Now how can i update 6 professional to 6.5
Click to expand...
Click to collapse
for upgrade to WM 6.5, you can follow existing Guide by krazy_about_technology at http://forum.xda-developers.com/showthread.php?t=472169