Hi
i flashed AP40 as per all the rite moves
Worked fine for 1st day
Then when turning it on it froze
Then unfroze but everything works fine as long as you use the joystick on side and windows key and ok
ie the touchscreen does not respond any more
i reflashed ap40 same problem
Now it cannot align the screen as touchscreen is not seeing anything ???
Help she cried
mw22 said:
Hi
i flashed AP40 as per all the rite moves
Worked fine for 1st day
Then when turning it on it froze
Then unfroze but everything works fine as long as you use the joystick on side and windows key and ok
ie the touchscreen does not respond any more
i reflashed ap40 same problem
Now it cannot align the screen as touchscreen is not seeing anything ???
Help she cried
Click to expand...
Click to collapse
Have you tried a hard reset? If not, then try it. It should prompt you back through the start-up and screen calibration as a new flash. For info on a hard reset, read the Wiki. You can also try to flash back to the modified AP3 and see if your device is working there. You may actually have a hardware issue.
hi
foun problem Screen protector had becom desensitised and no feedback on screen ??
I left device in car and it became hot screen protector got slight brown mark on edge
new one on me
Now working fine
Whew close call
mw22 said:
hi
foun problem Screen protector had becom desensitised and no feedback on screen ??
I left device in car and it became hot screen protector got slight brown mark on edge
new one on me
Now working fine
Whew close call
Click to expand...
Click to collapse
Glad you fixed your problem. Someone else in the forum had screen problems, I will advise him to try a new screen protector before he sent his unit off for repair.
please do
as i said first for me
normally screen protector packs up gradually but this time just went in one hit ?
I just picked up a new screen protecter for my 7501 from Clear Protector,
it's supposed to be bullet proof,time will tell.
It went on easily and you can't tell it from the original
screen,this stuff is supposedly used on helicopter rotor
blades lead edges to prevent damage from airborne debris.
At $9.95 an application it's not cheap.
bigtsr said:
I just picked up a new screen protecter for my 7501 from Clear Protector,
it's supposed to be bullet proof,time will tell.
It went on easily and you can't tell it from the original
screen,this stuff is supposedly used on helicopter rotor
blades lead edges to prevent damage from airborne debris.
At $9.95 an application it's not cheap.
Click to expand...
Click to collapse
Could you post a link? I always have many problems putting screen protectors on, and the end result is not good - bubbles round the edges etc. even with quality ones, like the Martin protector I have now. I wouldn't mind paying a bit extra for a decent one that went on easily and looked good.
JonSlater said:
Could you post a link? I always have many problems putting screen protectors on, and the end result is not good - bubbles round the edges etc. even with quality ones, like the Martin protector I have now. I wouldn't mind paying a bit extra for a decent one that went on easily and looked good.
Click to expand...
Click to collapse
Yes no problem for the link,make sure you follow theur instructs exactly
re install.
http://cgi.ebay.ca/CP-SCREEN-PROTEC...ryZ20336QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
www.ClearProtector.com
Related
Hello,
yesterday I installed some new games on my p4350 and let a friend play with it,
unfortunally he pushed to hard with the stylus and the screen got damaged . the screen is still working but it got a dent.
now I wanna replace the screen myself, anybody can give me instructions how to do this?
Also i wanna know if the soft layer on the top(not the screen protector) and the lcd, is one thing.
http://mikechannon.net/PDF Manuals/HTC Herald Sevice Manual.pdf
download and read that ,it will show you how to disassemble the herald and take the screen out
Replacing digitiser on Herald as opposed to Hermes
Scuse me for butting in but I have both just bought a Herald with a broken screen AND have done a few screen replacements on Wizards, Blue Angels and Hermeses.
On this Herald I had just assumed that you could basically follow the video on YouTube which shows how to replace a screen on a Hermes? I see that the PDF file is quite complicated and is designed to show you how to take off every tiny part if it has failed. The screen replacement is far easier that this, right?
Secondly, I see that you can buy the screen separately from the 'protector' which is I assume the bit with the hole in on your unit? I have to say, I had never seen these replaced separately before: Is this something special to the Herald or can you replace this digitizer separately from the screen on other units as well? If so, how on earth do you get it off the screen please? And is there a reliable way of getting one back on? (There is no reference to this in the pdf manual but the digitizers are suddenly being sold on ebay for about five bucks)
So the question is whether this is still as difficult on the Herald as threads on the Hermes suggest?
I've opened my Herald, and to reach the screen you have to disassemble the whole thing.
It's not that difficult (albeit while following the service manual, since there are a lot of tricky areas like removing the Keyboard), you just need to have patience and not rush it.
Any way to set up device after flash with no touch screen.
The digitizer or screen is not functioning, before i take it all apart as shown anybody no of a way to bypass the touchscreen setup.
before trying to change the digitizer...
(and i know this is crazy but worked for me after replacing the cable going from the screen to the board)
install a screen protector and try again!
I had the same problem after opening my Herald, and right now the screen only works if i have a screen protector on. If not then nothing happens
digitizer replacement is actually very easy.
Jeffreyr1 said:
Hello,
yesterday I installed some new games on my p4350 and let a friend play with it,
unfortunally he pushed to hard with the stylus and the screen got damaged . the screen is still working but it got a dent.
now I wanna replace the screen myself, anybody can give me instructions how to do this?
Also i wanna know if the soft layer on the top(not the screen protector) and the lcd, is one thing.
Click to expand...
Click to collapse
As I have now posted on a different thread, the digitizer replacement is actually very easy. You just slip a razor blade under the tabs and lever it off after removing that yellow tape on the back.
moullas said:
I've opened my Herald, and to reach the screen you have to disassemble the whole thing.
It's not that difficult (albeit while following the service manual, since there are a lot of tricky areas like removing the Keyboard), you just need to have patience and not rush it.
Click to expand...
Click to collapse
I agree. It was not difficult at all. I took apart and put together the phone a few times after just to develop a feel for it.
We have a tendency to get nervous about it but if you relax it becomes easier.
I have a a extra digitizer that I never used. If anyone wants it, pm me.
Hi all,
Has anyone experience with a problem when the touch screen intermittently works, especially when you press/hold hard on the sides of the face of the phone. Without pressing down on the side, the top menu (start... x) most of the time are either unresponsive or respond as if you press elsewhere on the screen.
I'm thinking of open up the phone later tonight to troubleshoot, guessing the screen digitizer is loose or, HOPEFULLY NOT, cold solder somewhere. But if you'd heard or faced this problem before or even have an idea on what has caused the problem, I'd like to hear from you. Please help!
Thanks!
Adding info
Oh yeah, did I forget to say that not just the top of the screen, the middle part as worst. The only part of the screen is still responsive is the bottom. If I press down or punctual around the face of the phone tightly enought(?), I'd be able to have the good touch screen for a little while (5... 10 minutes) before it gone weird again.
Fixed... for now
Well, I jammed a couple of thin plastic to the bottom of the screen within the housing facelet behind the t-mobile logo... and it works... for now.
I still intend to disassemble the dawn thing as soon as I realize such quick fix has become unpractical or no longer work.
I will check back to this post again, so if you are interested, don't hesitate to reply, I'll try anything when desperate.
How long have you had the phone?
How do you carry it around?
If you got the phone recently and started carrying it around by putting it in your pants pocket, then you find the screen sometimes doesn't work well, those facts are related. A couple of years ago people used to always complain about this, and some recommended rubbing your finger firmly around all edges of the screen for a temporary fix. Others recommended forcing a business card under the metal at the edges of the screen. I got a leather belt case for mine, and the problem went away.
If you've had the phone for years and it just now started acting up, the problem might be related to a cable, connection, or something. There is a wizard service manual online. I've used its instructions to replace a screen, with no bad issues.
Good luck with your phone. The wizard is a bit old, but still pretty nice.
I'm a simple amateur. Please, don't criticize my rustical methods. I did the best I could.
I could'nt separate the screen from the housing: too tight!! (I bought the two pieces and I replaced both)
Hope it helps someone
Nice Thanks mate!
dejx said:
Nice Thanks mate!
Click to expand...
Click to collapse
Thanks to you dejx
165 views and only 1 agreement... sniff, sniff
Nice Video.
Hopefully I will never need to take mine apart.
And here you are the reassembly.
Look in first post
you're welcome
Nice stuff
I'm gonna follow your video as a guide next time I change the housing.
Thanks!
How about Dust isn't there a risk of having dust stuck between the digitizer and lcd? isn't it the same risk as in aplying screen protection. I tried several time aplying screen protector but never succeed without having dust particle stuck in between even though it's allmost unnoticable.
What's your experiance in this ?
jpfa said:
How about Dust isn't there a risk of having dust stuck between the digitizer and lcd? isn't it the same risk as in aplying screen protection. I tried several time aplying screen protector but never succeed without having dust particle stuck in between even though it's allmost unnoticable.
What's your experiance in this ?
Click to expand...
Click to collapse
That's what I feared and that's why I put on the gloves and I was careful to clean the internal part of the screen before the assembly.
It may be a very small particle of dust, but I can't really see it.
Very nice tutorial. I guess i have to change my digitizer too sometime in the future because it has a defect (these newton rings) and i dont know how long it will work with this defect. I'm sure your videos will help me.
Eyghon said:
Very nice tutorial. I guess i have to change my digitizer too sometime in the future because it has a defect (these newton rings) and i dont know how long it will work with this defect. I'm sure your videos will help me.
Click to expand...
Click to collapse
I hope it helps you too. Ask me if you have any doubt. I will try to help you if I can
Great HowTo, thanks!
Thanks!
Nice tutorial, hope I will never need it.
Was the reassembled phone fully working at the first time or did you need some further tries.
Thanks, nhedgehog
nhedgehog said:
Nice tutorial, hope I will never need it.
Was the reassembled phone fully working at the first time or did you need some further tries.
Thanks, nhedgehog
Click to expand...
Click to collapse
The device works ok. At the beginning I had to realign the screen. Few days ago I realized that the screen had the oil stain (the device was working perfectly), and I made it disappear with a tape.
what if the part I purchased doesn't come with the metal surrounding. Only the glass do you use glue to stick it on the chassi ? any tips on this issue before taking my phone apart ? or you recomend to send back the glass and get the whole front? Thank for the video it must have taken you some time to edit.
jpfa said:
what if the part I purchased doesn't come with the metal surrounding. Only the glass do you use glue to stick it on the chassi ? any tips on this issue before taking my phone apart ? or you recomend to send back the glass and get the whole front? Thank for the video it must have taken you some time to edit.
Click to expand...
Click to collapse
I heard that many people has broken the original digitizer trying to separate it from the housing.
That's why I bought both pieces.
But I also heard that is possible to separate them, being very careful. But it's a risk. And I heard too that you can use any kind of glue, including the one we used at school.
I hope that I have understood your question.
Thanks for you greatefulness!
very usefull tutorial
I have bought me a touch diamond 2, with a pretty damaged housing
now I dare to try to replace it, thanks to you're tutorial
First, thank you for your useful guide, but i missed something.
What about the light sensor cover (it's at the opposite side of the power LED). Is it included in the new housing? Because i didn't find it on the new housing that I bought (may be because it is not an OEM?)
Thanx in advance!
blackice666 said:
First, thank you for your useful guide, but i missed something.
What about the light sensor cover (it's at the opposite side of the power LED). Is it included in the new housing? Because i didn't find it on the new housing that I bought (may be because it is not an OEM?)
Thanx in advance!
Click to expand...
Click to collapse
Yes, my new housing has the other led.
I have tried to disassemble this led from my old housing but... I failed.
Sorry,but I can't help you with this.
Something72 said:
The device works ok. At the beginning I had to realign the screen. Few days ago I realized that the screen had the oil stain (the device was working perfectly), and I made it disappear with a tape.
Click to expand...
Click to collapse
How did you realign the screen? I tried to use the calibration utility but I it goes into an endless loop. tried to re-assemble but got the same result
Any ideas what might be wrong?
voxter said:
How did you realign the screen? I tried to use the calibration utility but I it goes into an endless loop. tried to re-assemble but got the same result
Any ideas what might be wrong?
Click to expand...
Click to collapse
Sorry, voxter.
I realign the screen using the app included in settings (Settings > System > Screen > Align Screen).
I read in other thread that you tried without success (just endless bucle). I had endless bucle too in another ROM. But after two or three times I made a soft reset and the screen begun to work perfectly.
Now I have a Tess ROM and only asked me to repeat it twice. After that, the screen works perfectly.
It's all that I know about it. Hope it helps
So, about 2 weeks ago, I got my HD2 off of Craigslist with a cracked screen. It worked perfectly fine with the exception of the hardly noticeable cracks. I knew I could get the replacement digitizer/screen for $40-80. I got my screen in the mail yesterday and, following the "YouTube" video tutorial found on this site, I......ugh.... replaced the screen....................I SCREWED UP BIG TIME!
First, I broke the ribbon cable for the Side "Volume Up/Down" buttons. Then, I broke the ribbon cable for the "soft keys." Ah, crap, but oh well. I figured I could use the touch screen for pretty much everything i needed to do. Well, while prying the cracked digitizer screen from the LCD, I went a bit too deep & peeled the tinted film off of the LCD. I thought nothing of it at the time. I'd already done enough damage. So the display would be a bit brighter than normal oh well.......WRONG! I put the phone back together and once I get it to power up, all I get is a white screen. I thought I missed something. So I disassemble & check 3 more times. Still a white screen.
Well, after all of this, the new digitizer/screen doesn't want to stay in place very well. So, being pissed off and curious, I pull it out and away and notice in the backside reflection of the digitizer that I can slightly make out the phone display. So, apparently the "Tinted Film" that I accidentally peeled off of the LCD makes images visible on the phone screen. I kind of damaged this film when peeling it off. Therefore, I am unable to put it back on. Does anyone know of a simple fix without replacing the LCD?
SORRY FOR THE "SHORT STORY LONG."
I was brainstorming and thought that maybe the film was polarized. So, I grabbed my sunglasses, which are polarized, and wearing them, I can faintly see the display. Anyone think maybe polarized window tint might fix my problem?
Hey man I have some electronic devices that need repair, can I send them to you to fix them?
SURE!
You can pay me in HD2 parts.
Sir i can only say 1 thing. search ebay and replace everything you damaged. only that way you will get your hd2 in perfect state.
keesmathot said:
Sir i can only say 1 thing. search ebay and replace everything you damaged. only that way you will get your hd2 in perfect state.
Click to expand...
Click to collapse
I'd go one step further and say bin it and get a new one!
You sound just like me. That is why I never try things like that anymore. Hope it gets sorted but might be better looking for a used one.
I've got it functioning...
I found the film that I ripped off, put it over the screen and........I CAN SEE! However, the top half has lines through it. So, I must've damaged the LCD. The good news is that my phone is useable again. I just have to do everything via the touch screen and can't let the screen hibernate unless I have my charger close by. I'm just gonna keep my eye out for a cheap busted phone and eventually have a 100% phone again...
I sympathize with you. I broke HD2 while I was trying to check for loose WiFi card cable(cuz i was getting weak WiFi signals). The cable turned out to be fine but the external speaker stopped working. I opened it up again and adjusted some parts and it just got worse. the HD2 didn't power on at all. I tried fixing it but to no avail. I ended up sending the HD2 to a repair shop and was charged $170 for the repair. the repair guy said i messed up the power IC and the connector for the external speaker and he had to replace the power IC and resolder the connector.
I think I'm gonna stop trying to open up expensive phones. i was stupid thinking that since I have successfully replaced digitizer for my previous Palm T3, E2 and T5, opening up HD2 wouldn't be a problem. Should have known HD2 components are really fragile...
mmarkk said:
Hey man I have some electronic devices that need repair, can I send them to you to fix them?
Click to expand...
Click to collapse
made me laugh.......
The best topic ever Thanks, dude!
So I'm watching youtube on the dual screen using landscape and I want to sleep the main screen so i touch sleep main screen option on the dual screen tab tool, it shows a prompt saying main screen will dim to save battery and swipe to dismiss. I dont touch or swipe anything and the prompt swipes itself away and screen undims or sometimes doesn't even dim. This is also the case with Call of duty mobile, when I'm playing the game in battle royal mode the mini map enlarges randomly even if I don't touch it, and the voice chat options will engage and open without me touching those as well. Anyone else has this problem? Any solutions?
I could have sworn I saw a post earlier about ghost touches, though I can't seem to find the thread it was in at the moment.
I've been using the phone heavily since I got it on April 1st, and I have not experienced this issue at all.
Any chance you had an LG phone prior to this and used LG Switch to transfer over all of your stuff?
I've read reports here that doing so can cause some pretty serious battery drain and/or lag issues, so there could be other bugs as another side-effect.
Have you tried a factory reset?
Mejilan said:
I could have sworn I saw a post earlier about ghost touches, though I can't seem to find the thread it was in at the moment.
I've been using the phone heavily since I got it on April 1st, and I have not experienced this issue at all.
Any chance you had an LG phone prior to this and used LG Switch to transfer over all of your stuff?
I've read reports here that doing so can cause some pretty serious battery drain and/or lag issues, so there could be other bugs as another side-effect.
Have you tried a factory reset?
Click to expand...
Click to collapse
Yeah I think I read that thread. I haven't tried a reset since I already used so much data to download apps and don't want to setup the phone again. I did use the google cloud restore for my contacts and I also had the t mobile April security update. Mejilan can you tell me if you can put your main screen to sleep while watching a youtube video on the dual screen? Please tell me what kind of result you get. Thanks
Lowe941 said:
Yeah I think I read that thread. I haven't tried a reset since I already used so much data to download apps and don't want to setup the phone again. I did use the google cloud restore for my contacts and I also had the t mobile April security update. Mejilan can you tell me if you can put your main screen to sleep while watching a youtube video on the dual screen? Please tell me what kind of result you get. Thanks
Click to expand...
Click to collapse
I set aside the the dual-screen accessory because it's just too uncomfortable to hold for most use-cases.
I'll go dig it up, plug it in, and give it a shot later, when I have some free time, and report back.
https://forum.xda-developers.com/lg-v60-thinq/help/phantom-home-button-presses-t4082573
Above is the link for the other thread.
Lowe941 said:
Yeah I think I read that thread. I haven't tried a reset since I already used so much data to download apps and don't want to setup the phone again. I did use the google cloud restore for my contacts and I also had the t mobile April security update. Mejilan can you tell me if you can put your main screen to sleep while watching a youtube video on the dual screen? Please tell me what kind of result you get. Thanks
Click to expand...
Click to collapse
If you play a YT video on the second screen and lock/sleep your phone, the second screen goes to sleep as well.
I didn't bother with headphones for this test, and noticed that the audio comes out of the phone's speakers.
It appears that the second screen doesn't have speakers of its own.
So yeah, you cannot watch something on the second screen while having the phone asleep.
And it make sense. It's just a screen. No second pair of speakers. No second headphone jack. No separate battery. No second set of modems, etc.
Mejilan said:
I set aside the the dual-screen accessory because it's just too uncomfortable to hold for most use-cases.
I'll go dig it up, plug it in, and give it a shot later, when I have some free time, and report back.
Click to expand...
Click to collapse
It actually was working for me last night as far as the putting main screen to sleep function but call of duty still acts up I'm hoping the update for the game on May 1St will fix, but sure whenever you get a chance...
Lowe941 said:
It actually was working for me last night as far as the putting main screen to sleep function but call of duty still acts up I'm hoping the update for the game on May 1St will fix, but sure whenever you get a chance...
Click to expand...
Click to collapse
I answered your YT question one post above yours that I just quoted.
Mejilan said:
I answered your YT question one post above yours that I just quoted.
Click to expand...
Click to collapse
Actually you CAN watch youtube on the second screen and sleep/dim the main screen by using the floating dual screen button. It has an option asking if you want to sleep dim the main screen to conserve battery life. It does work for me now, I'm not sure why it was going wonky on me when I first posted but hopefully that it doesn't do it anymore. I'm guessing the tmobile April security update did the trick. It's just I have phantom touches on call of duty still.
Lowe941 said:
This is also the case with Call of duty mobile, when I'm playing the game in battle royal mode the mini map enlarges randomly even if I don't touch it, and the voice chat options will engage and open without me touching those as well. Anyone else has this problem? Any solutions?
Click to expand...
Click to collapse
This is happening to me as well when I'm playing PubG Mobile. The ghost touches are happening not on the map but to the left of that. On another LG V60, the device would get random dead zones as well.
I'm going to do the following test and suggest you do the same and report back your results.
1. wait until the ghost touches start happening and flip the phone around. hopefully the ghost touch continues to happen in the same exact location of the physical screen, and it triggers a different button
2. remove the screen protector and try the tests again
are you using a screen protector?
might process a warranty replacement if the results are reproduceable
Lowe941 said:
Actually you CAN watch youtube on the second screen and sleep/dim the main screen by using the floating dual screen button. It has an option asking if you want to sleep dim the main screen to conserve battery life. It does work for me now, I'm not sure why it was going wonky on me when I first posted but hopefully that it doesn't do it anymore. I'm guessing the tmobile April security update did the trick. It's just I have phantom touches on call of duty still.
Click to expand...
Click to collapse
Oh, that is good to know. I'm not using the dual-screen attachment anymore (typing in portrait mode is IMPOSSIBLE with it), but I only ever used the Dual-Screen notification shade tile to enable the second screen, not the pill button thing. I should have explored our options more thoroughly. Thank you for correcting me.
Edit - I have recently added a tempered glass screen protector to my phone, and while it completely screwed with my fingerprint biometrics (I had to delete the fingerprints and redo them), the protector itself is not causing any ghost touches for me. And once I redid the fingerprints, there have been no further issues there either.
jd254 said:
This is happening to me as well when I'm playing PubG Mobile. The ghost touches are happening not on the map but to the left of that. On another LG V60, the device would get random dead zones as well.
I'm going to do the following test and suggest you do the same and report back your results.
1. wait until the ghost touches start happening and flip the phone around. hopefully the ghost touch continues to happen in the same exact location of the physical screen, and it triggers a different button
2. remove the screen protector and try the tests again
are you using a screen protector?
might process a warranty replacement if the results are reproduceable
Click to expand...
Click to collapse
Yes I am using a screen protector and I was actually thinking that might be the problem, although it seems like a solid install. I just got the update for cod season 6 and I'm downloading now. I'll see if that solves the problem. I'll also try what you suggested and then post results
Update: so the cod update did not fix the issue, but I tried doing as you suggested and flipped the phone around and the problem went away. I then tried flipping it back to original and problem persisted. I think it is the tempered glass. I don't want to remove it since it cost me 40 bucks. Any suggestions?
Mejilan said:
Oh, that is good to know. I'm not using the dual-screen attachment anymore (typing in portrait mode is IMPOSSIBLE with it), but I only ever used the Dual-Screen notification shade tile to enable the second screen, not the pill button thing. I should have explored our options more thoroughly. Thank you for correcting me.
Edit - I have recently added a tempered glass screen protector to my phone, and while it completely screwed with my fingerprint biometrics (I had to delete the fingerprints and redo them), the protector itself is not causing any ghost touches for me. And once I redid the fingerprints, there have been no further issues there either.
Click to expand...
Click to collapse
So I installed the update for cod and it still had the ghost touch problem with the top right side of the screen, iflipped the phone per what jd254 suggested and I didn't get the phantom touches. I'm assuming it is the tempered glass that is causing it. I dont want to remove it cause it cost me 40 bucks.
2nd update: so I tried taking it out of the dual screen case and notice it doesn't have phantom touch ( I played a full game of battle royale) so I'm not sure if its the tempered glass or the case. Need to investigate more
Lowe941 said:
So I installed the update for cod and it still had the ghost touch problem with the top right side of the screen, iflipped the phone per what jd254 suggested and I didn't get the phantom touches. I'm assuming it is the tempered glass that is causing it. I dont want to remove it cause it cost me 40 bucks.
2nd update: so I tried taking it out of the dual screen case and notice it doesn't have phantom touch ( I played a full game of battle royale) so I'm not sure if its the tempered glass or the case. Need to investigate more
Click to expand...
Click to collapse
Is the case touching the tempered glass anywhere around the the edges? If the case is pressing on the screen protector and lifting or peessing it even the smallest amount that could cause phantom touches maybe..just an idea
FWIW, I'm using both a tempered glass screen protector and a case that wraps around to grip the front of the phone a bit, and I'm not getting any phantom touches at all.
The case is NOT rubbing up against the edges of the screen protector, however. Which is fine, because if it were, it could potentially dislodge it.
Or, I suppose, cause phantom touches.
Ryano89 said:
Is the case touching the tempered glass anywhere around the the edges? If the case is pressing on the screen protector and lifting or peessing it even the smallest amount that could cause phantom touches maybe..just an idea
Click to expand...
Click to collapse
Ok more investigating and playing codm I notice that the mini map opens up when i perform a touch combination with my thumbs. So the map gets triggered when I press and hold up on the left side virtual joystick to sprint and press the jump virtual button on the right simultaneously. I can't recreate what button presses open the voice chat box, but now I have to strike the dual case as being the problem along with the tempered glass, at least i assume those aren't causing the ghost touches.
For anyone having touch issues, as a troubleshooting aid: enable developer options, and then toggle on "Show touches" and "Show touch data". Might help figure out what is going on.
bilbo60 said:
For anyone having touch issues, as a troubleshooting aid: enable developer options, and then toggle on "Show touches" and "Show touch data". Might help figure out what is going on.
Click to expand...
Click to collapse
Awesome thanks I forgot how to enable developer options...
Never mind developer option enabled
bilbo60 said:
For anyone having touch issues, as a troubleshooting aid: enable developer options, and then toggle on "Show touches" and "Show touch data". Might help figure out what is going on.
Click to expand...
Click to collapse
I'm getting VERY interesting results.
1. dead spots: I moved my finger up the right side of the screen to look up. my character did not look up, which I would assume there was a dead spot before. This is incorrect. I can see the screen registered using that option mentioned above. the screen registered the action, but didn't pass it to the software?
2. FPS drops: I assume it's an FPS drop because everything was laggy when this happened. (PubG mobile was set to max settings, and runs 100% fine, until now) I was flying the helicopter, so I had several fingers on the screen at the same time, with a lot of rotational movements. the screen doesn't clear all of these movement data until I literally take all my fingers off the screen for half a sec. When I did that, it stop lagging.
3. ghost touches: Each touch on the screen has an x and y axis point to tell the software where it's being touched. With several finger on the screen (sometimes 2, but commonly with three or more), I noticed that the y axis for my left thumb and the x axis for my right thumb was creating those ghost touches! The screen would combine the x and y axis from different fingers to create a touchpoint on the screen.
so I don't care too much about 1 and 2, but... what can I do about 3?
jd254 said:
I'm getting VERY interesting results.
1. dead spots: I moved my finger up the right side of the screen to look up. my character did not look up, which I would assume there was a dead spot before. This is incorrect. I can see the screen registered using that option mentioned above. the screen registered the action, but didn't pass it to the software?
2. FPS drops: I assume it's an FPS drop because everything was laggy when this happened. (PubG mobile was set to max settings, and runs 100% fine, until now) I was flying the helicopter, so I had several fingers on the screen at the same time, with a lot of rotational movements. the screen doesn't clear all of these movement data until I literally take all my fingers off the screen for half a sec. When I did that, it stop lagging.
3. ghost touches: Each touch on the screen has an x and y axis point to tell the software where it's being touched. With several finger on the screen (sometimes 2, but commonly with three or more), I noticed that the y axis for my left thumb and the x axis for my right thumb was creating those ghost touches! The screen would combine the x and y axis from different fingers to create a touchpoint on the screen.
so I don't care too much about 1 and 2, but... what can I do about 3?
Click to expand...
Click to collapse
Yeah I noticed a combination of touches triggers the ghost touch on call of duty, I could also be having the combinations trigger ghost touches in other game but I need to test more