I'm a simple amateur. Please, don't criticize my rustical methods. I did the best I could.
I could'nt separate the screen from the housing: too tight!! (I bought the two pieces and I replaced both)
Hope it helps someone
Nice Thanks mate!
dejx said:
Nice Thanks mate!
Click to expand...
Click to collapse
Thanks to you dejx
165 views and only 1 agreement... sniff, sniff
Nice Video.
Hopefully I will never need to take mine apart.
And here you are the reassembly.
Look in first post
you're welcome
Nice stuff
I'm gonna follow your video as a guide next time I change the housing.
Thanks!
How about Dust isn't there a risk of having dust stuck between the digitizer and lcd? isn't it the same risk as in aplying screen protection. I tried several time aplying screen protector but never succeed without having dust particle stuck in between even though it's allmost unnoticable.
What's your experiance in this ?
jpfa said:
How about Dust isn't there a risk of having dust stuck between the digitizer and lcd? isn't it the same risk as in aplying screen protection. I tried several time aplying screen protector but never succeed without having dust particle stuck in between even though it's allmost unnoticable.
What's your experiance in this ?
Click to expand...
Click to collapse
That's what I feared and that's why I put on the gloves and I was careful to clean the internal part of the screen before the assembly.
It may be a very small particle of dust, but I can't really see it.
Very nice tutorial. I guess i have to change my digitizer too sometime in the future because it has a defect (these newton rings) and i dont know how long it will work with this defect. I'm sure your videos will help me.
Eyghon said:
Very nice tutorial. I guess i have to change my digitizer too sometime in the future because it has a defect (these newton rings) and i dont know how long it will work with this defect. I'm sure your videos will help me.
Click to expand...
Click to collapse
I hope it helps you too. Ask me if you have any doubt. I will try to help you if I can
Great HowTo, thanks!
Thanks!
Nice tutorial, hope I will never need it.
Was the reassembled phone fully working at the first time or did you need some further tries.
Thanks, nhedgehog
nhedgehog said:
Nice tutorial, hope I will never need it.
Was the reassembled phone fully working at the first time or did you need some further tries.
Thanks, nhedgehog
Click to expand...
Click to collapse
The device works ok. At the beginning I had to realign the screen. Few days ago I realized that the screen had the oil stain (the device was working perfectly), and I made it disappear with a tape.
what if the part I purchased doesn't come with the metal surrounding. Only the glass do you use glue to stick it on the chassi ? any tips on this issue before taking my phone apart ? or you recomend to send back the glass and get the whole front? Thank for the video it must have taken you some time to edit.
jpfa said:
what if the part I purchased doesn't come with the metal surrounding. Only the glass do you use glue to stick it on the chassi ? any tips on this issue before taking my phone apart ? or you recomend to send back the glass and get the whole front? Thank for the video it must have taken you some time to edit.
Click to expand...
Click to collapse
I heard that many people has broken the original digitizer trying to separate it from the housing.
That's why I bought both pieces.
But I also heard that is possible to separate them, being very careful. But it's a risk. And I heard too that you can use any kind of glue, including the one we used at school.
I hope that I have understood your question.
Thanks for you greatefulness!
very usefull tutorial
I have bought me a touch diamond 2, with a pretty damaged housing
now I dare to try to replace it, thanks to you're tutorial
First, thank you for your useful guide, but i missed something.
What about the light sensor cover (it's at the opposite side of the power LED). Is it included in the new housing? Because i didn't find it on the new housing that I bought (may be because it is not an OEM?)
Thanx in advance!
blackice666 said:
First, thank you for your useful guide, but i missed something.
What about the light sensor cover (it's at the opposite side of the power LED). Is it included in the new housing? Because i didn't find it on the new housing that I bought (may be because it is not an OEM?)
Thanx in advance!
Click to expand...
Click to collapse
Yes, my new housing has the other led.
I have tried to disassemble this led from my old housing but... I failed.
Sorry,but I can't help you with this.
Something72 said:
The device works ok. At the beginning I had to realign the screen. Few days ago I realized that the screen had the oil stain (the device was working perfectly), and I made it disappear with a tape.
Click to expand...
Click to collapse
How did you realign the screen? I tried to use the calibration utility but I it goes into an endless loop. tried to re-assemble but got the same result
Any ideas what might be wrong?
voxter said:
How did you realign the screen? I tried to use the calibration utility but I it goes into an endless loop. tried to re-assemble but got the same result
Any ideas what might be wrong?
Click to expand...
Click to collapse
Sorry, voxter.
I realign the screen using the app included in settings (Settings > System > Screen > Align Screen).
I read in other thread that you tried without success (just endless bucle). I had endless bucle too in another ROM. But after two or three times I made a soft reset and the screen begun to work perfectly.
Now I have a Tess ROM and only asked me to repeat it twice. After that, the screen works perfectly.
It's all that I know about it. Hope it helps
Related
Hi
i flashed AP40 as per all the rite moves
Worked fine for 1st day
Then when turning it on it froze
Then unfroze but everything works fine as long as you use the joystick on side and windows key and ok
ie the touchscreen does not respond any more
i reflashed ap40 same problem
Now it cannot align the screen as touchscreen is not seeing anything ???
Help she cried
mw22 said:
Hi
i flashed AP40 as per all the rite moves
Worked fine for 1st day
Then when turning it on it froze
Then unfroze but everything works fine as long as you use the joystick on side and windows key and ok
ie the touchscreen does not respond any more
i reflashed ap40 same problem
Now it cannot align the screen as touchscreen is not seeing anything ???
Help she cried
Click to expand...
Click to collapse
Have you tried a hard reset? If not, then try it. It should prompt you back through the start-up and screen calibration as a new flash. For info on a hard reset, read the Wiki. You can also try to flash back to the modified AP3 and see if your device is working there. You may actually have a hardware issue.
hi
foun problem Screen protector had becom desensitised and no feedback on screen ??
I left device in car and it became hot screen protector got slight brown mark on edge
new one on me
Now working fine
Whew close call
mw22 said:
hi
foun problem Screen protector had becom desensitised and no feedback on screen ??
I left device in car and it became hot screen protector got slight brown mark on edge
new one on me
Now working fine
Whew close call
Click to expand...
Click to collapse
Glad you fixed your problem. Someone else in the forum had screen problems, I will advise him to try a new screen protector before he sent his unit off for repair.
please do
as i said first for me
normally screen protector packs up gradually but this time just went in one hit ?
I just picked up a new screen protecter for my 7501 from Clear Protector,
it's supposed to be bullet proof,time will tell.
It went on easily and you can't tell it from the original
screen,this stuff is supposedly used on helicopter rotor
blades lead edges to prevent damage from airborne debris.
At $9.95 an application it's not cheap.
bigtsr said:
I just picked up a new screen protecter for my 7501 from Clear Protector,
it's supposed to be bullet proof,time will tell.
It went on easily and you can't tell it from the original
screen,this stuff is supposedly used on helicopter rotor
blades lead edges to prevent damage from airborne debris.
At $9.95 an application it's not cheap.
Click to expand...
Click to collapse
Could you post a link? I always have many problems putting screen protectors on, and the end result is not good - bubbles round the edges etc. even with quality ones, like the Martin protector I have now. I wouldn't mind paying a bit extra for a decent one that went on easily and looked good.
JonSlater said:
Could you post a link? I always have many problems putting screen protectors on, and the end result is not good - bubbles round the edges etc. even with quality ones, like the Martin protector I have now. I wouldn't mind paying a bit extra for a decent one that went on easily and looked good.
Click to expand...
Click to collapse
Yes no problem for the link,make sure you follow theur instructs exactly
re install.
http://cgi.ebay.ca/CP-SCREEN-PROTEC...ryZ20336QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
www.ClearProtector.com
Hi all!
Today I observed a rainbow blur on my TG01 upper display, it's seems like a liquid ,but it's under the surface and I can't clean it. It's like the crystal liquid it's came out somewhere or somehow.
It's could be a fissure or it's something else?
If it is, how it's this possible, because I treathed this phone like a jewel?
What do you think ,what it is.....?
I uploaded two photos about this.
What should I do?
Sorry for my english.
Thank you for answears.
do you have a screen protector on the screen? if so remove it and see if it disapears
jutley said:
do you have a screen protector on the screen? if so remove it and see if it disapears
Click to expand...
Click to collapse
There is no Screen protector uplied by me, it's in same shape like out of the box, only that, this movement was 2 months ago (out of the box)
I had the same with my first TG, that because you put it in your pocket without big protection.
This big screen don't like a "hold pressure"
PHOTO= http://nsa09.casimages.com/img/2009/09/30/090930040951125085.jpg
Nothing to do for repair.
Sorry for you
LeTo08 said:
I had the same with my first TG, that because you put it in your pocket without big protection.
This big screen don't like a "hold pressure"
PHOTO= http://nsa09.casimages.com/img/2009/09/30/090930040951125085.jpg
Nothing to do for repair.
Sorry for you
Click to expand...
Click to collapse
That's mean that it can't be returned or changed in warranty at Orange?
How do you managed that?
pitagorasz said:
That's mean that it can't be returned or changed in warranty at Orange?
How do you managed that?
Click to expand...
Click to collapse
I've seen in a Spanish forum that people with the same issue have obtained a new one from the Spanish dealer (telefonica) under guarantee..
Good luck
Pere said:
I've seen in a Spanish forum that people with the same issue have obtained a new one from the Spanish dealer (telefonica) under guarantee..
Good luck
Click to expand...
Click to collapse
Thank's , I will give it a try, and keep you inform about the situation.
my touch its dead
So I started testing.
the problem its touch screen.
display its ok!
touch screen is on a plastic surface.
Initially there was very little distance between the two
because of adhesive tape on the plastic (touch screen)
after a while they are to close, and then see those refraction,
the rainbow.
darckreign1984 said:
So I started testing.
the problem its touch screen.
display its ok!
touch screen is on a plastic surface.
Initially there was very little distance between the two
because of adhesive tape on the plastic (touch screen)
after a while they are to close, and then see those refraction,
the rainbow.
[/URL]
Click to expand...
Click to collapse
Thank's It's very good information, this way we know that rainbowing effect it's caused by the construction of the phone and can happen with anybody, so in this cause Orange (in my case) must replace the phone in guarantee...
I will keep you guys in touch.
Unless I'm very much mistaken this rainbow effect is harmless, because you can't see it when the backlight is on, and it doesn't affect device operation. It doesn't look as good when the device is turned off, but that's about it.
Or am I mistaken?
paroariax said:
Unless I'm very much mistaken this rainbow effect is harmless, because you can't see it when the backlight is on, and it doesn't affect device operation. It doesn't look as good when the device is turned off, but that's about it.
Or am I mistaken?
Click to expand...
Click to collapse
the rainbow that u see on the screen is called a newton's ring, it happens from pressure applied on the screen, it only happens to resistive touchscreens and not capactive, and if u dont take care of it, it may start to spread, i recommend that you should have used to screen protecter beacuse it usually helps protect this from happening, good luck!
What kind of screen protector would you recommend? Surely any kind of transparent soft case will apply the same kind of pressure to the screen. Or do you mean some kind of hard case that prevents any contact with the screen?
paroariax said:
What kind of screen protector would you recommend? Surely any kind of transparent soft case will apply the same kind of pressure to the screen. Or do you mean some kind of hard case that prevents any contact with the screen?
Click to expand...
Click to collapse
keep ur phone in ur jacket inner pocket , and not ur pants where it gets bent and pressured ... thats wat im doin
souljaboy said:
keep ur phone in ur jacket inner pocket , and not ur pants where it gets bent and pressured ... thats wat im doin
Click to expand...
Click to collapse
Good advice, keep it in mind!
Keeping it in my trousers' pocket costed me a bloody display(no kidding...)!!!
Hi guys
In Poland We have this same problem.
This is a unstick touch layer.
The reason of problem is bad heat dissipation from procesor.
When We use very strong own TG01 the Snapdragon have about 60'C and this type touch display is very susceptible to heat.
This problem is general problem of users TG01.
The cost of new touch display is hmm about 45 Euro.
After about 5 months use the first "oil spots" appear on the display.
When We use with this problem after 1 month have problem with less sensitivity of the screen.
i just saw the same thing with my tg01 today...but it`s a lot bigger...about 3 quarters of the screen but in the center...what should i do?
ps: i keep it in my jacket pocket...and there is no presure on it...i don`t know what could o caused this...
sattodude said:
i just saw the same thing with my tg01 today...but it`s a lot bigger...about 3 quarters of the screen but in the center...what should i do?
ps: i keep it in my jacket pocket...and there is no presure on it...i don`t know what could o caused this...
Click to expand...
Click to collapse
If your still under warranty, contact toshiba
olyloh6696 said:
If your still under warranty, contact toshiba
Click to expand...
Click to collapse
And if not....
http://global.ebay.com/Original_Toshiba_TG01_TG_01_Touchscreen_Touch_Screen_/360304861826/item
Good luck
Pere said:
And if not....
http://global.ebay.com/Original_Toshiba_TG01_TG_01_Touchscreen_Touch_Screen_/360304861826/item
Good luck
Click to expand...
Click to collapse
Does it void warranty to replace it yourself?
olyloh6696 said:
Does it void warranty to replace it yourself?
Click to expand...
Click to collapse
The full phrase was: AND IF you are NOT still under warranty.....
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
SecUpwN said:
This is a topic which I don't really like to talk about, but I now want to take the approach to get it outa my mind: The backlight of my soft-key search button does not fully shut down. That is, if I let the phone sit until the lights of the soft-keys (home, menu, back- and search button) shut down, I still see a dimmed light behind my search button. It annoys me.. I know I'm a picky girl.
Is that a hardware failure or do you guys have that, too? I'm convinced it's NOT caused by my current ROM (running DisarmedToaster). Can you recommend an app which will test my phone for hardware failures?
I bought my EVO 3D with blood money and would not really like unrooting and putting the phone into original warranty state to go beg the company I bought it from for a replacement. Please help a desperate lady!
Click to expand...
Click to collapse
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
richyrocket said:
Mine has done that since the day I bought it, although I bought mine used so I just dealt with it. It looks more like bleed from the backlight on the display but i'm not sure. It must be pretty common if we both have it.
Click to expand...
Click to collapse
Thank you so much for stating this, exactly what I was talking about! Kind of a small release to hear I didn't buy faulty hardware. Do we have other readers here who can confirm that this behavior is normal?
I'll head out to the phone store today to double check. Still, does an app exist to check for hardware failures?
Yes no faulty equipment, it is normal on every single Evo.
( Don't ask for help as I couldn't care if your phone explodes, eh)
flashallthetime said:
Yes no faulty equipment, it is normal on every single Evo.
Click to expand...
Click to collapse
You just saved my whole HTC experience. Thank you soo much! How come this is the case on every EVO? Isn't that something draining the battery?
No it is actually bleeding from the main screen, I guess there's a small gap between the search button and the screen
( Don't ask for help as I couldn't care if your phone explodes, eh)
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Use your phone in the dark. Watch until soft buttons stop glowing. See the light behind the search button?
Mine has it too.
Sent from my HTC EVO 3D X515m using xda app-developers app
Jsparta26 said:
I noticed that too, but only when I boot up my phone, then the problem goes away after it gets past the boot animation.
Click to expand...
Click to collapse
Turn the backlight of touch buttons off using kernel tuner and keep screen on, you will notice light behind search key.
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
dessolator666 said:
Yeh, methinks it's standard in all our phones fixed mine when i was replacing my digitizer (put a bit of plastic behind the search key to stop the overspill)
Click to expand...
Click to collapse
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
SecUpwN said:
Did you void your warranty through opening it? How about the buttons responsiveness afterwards? If you provide a detailed HowTo, you'll get another +1. :thumbup:
Click to expand...
Click to collapse
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
dessolator666 said:
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
That would actually be the coolest contribution I've seen in a ling time! Are you really willing to do that for our EVO community? If you did, you'd be our king.
Don't worry, it's on every EVO 3D. From GSM to CDMA.
The light bleed is from the screen back light. It does give the phone a cheap feel sometimes, but it's a common problem.
It's not as prevalent on cm10 with inverted gapps
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
flashallthetime said:
It's not as prevalent on cm10 with inverted gapps
Click to expand...
Click to collapse
How come?
SecUpwN said:
How come?
Click to expand...
Click to collapse
Inverted gapps has black backgrounds so the screen bleeding is reduced
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
---------- Post added at 10:56 PM ---------- Previous post was at 10:51 PM ----------
I can drastically reduce screen brightness which helps, there's still some bleeding
(Don't ask me for help as I couldn't care if your phone explodes, eh! )
dessolator666 said:
Yeh, warranty gone after opening it.... though now that I think of it... there may be a way around that. Namely I replaced the entire digitizer so I needed to take it apart fully, however since all the connections and cables are at the top of the screen and the buttons are (obviously ) on the bottom you could lift the digitizer up from the bottom and fix it without messing with the screws in the back (the one that voids your warranty).
To actually do this you will need:
Heat gun(or decent hair drier) anything with 500w or above should be plenty
Some good double sided adhesive tape (probably won't be able to reuse the original one)
A case opener tool (to lift the digitizer)
A piece of plastic or anything else opaque and nonconductive
Procedure:
heat up all the edges of the digitizer evenly (don't cook them, just heat them up )
Using a case opener tool get in between the digitizer and the aluminium chassis starting at the bottom and work your way up to the top
When the bottom and sides are free gently lift the digitizer with the top as a hinge point heating it up if necessary.
Ta da! You can see the inner workings of the buttons
Notice that the buttons have pieces of transparent plastic leading light from the LEDs to the actual surface the light overspill happens around the search button so I put a tiny piece of plastic around it (there are probably more elegant ways around this... but I'm not that elegant to begin with so this worked just fine.
Cut out thin strips of tape and put them on the edges of the digitizer where the old adhesive was (or reuse the old adhesive if you can)
Close up the phone and there you have it... your warranty should still be valid... tho if any1 opens the phone up they will probably notice the extra piece of plastic (or whatever you used)
On a similar note my gf's digitizer is busted so I will be replacing it some time this or next week and could probably demonstrate this with photos before I actually replace the darn thing (assuming I can get ahold of a decent camera)
Click to expand...
Click to collapse
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
HermanV0929 said:
I don't believe it can be done without opening the back. If I'm not mistaken, that's where the connector is and it can't be accessed from the front. I could be wrong though
Sent from my PG86100 using Tapatalk
Click to expand...
Click to collapse
I'm sure it can be done... because you have to do pretty much exactly that when replacing the LCD or digitizer
I ordered a screen/digitizer assembly to replace mine because its cracked. I didn't want to disbond the digitizer so I ordered the whole assembly.
When I installed the new. assembly, the screen wont come on and the phone wont boot. Here is where thing started to get interesting:
1. Boot the phone with the old screen assembly and wait until the home screen shows then turn off screen.
2. Disconnect the old screen at this moment and connect the new one while the phone in sleep mode.
3. push power button to wake screen and its working and fully functional.(New one)
If I tried to reboot the phone the new screen wont come back on again. I also tried to reset and RUU and it still wont work.
Please let me know if you have any suggestions. I am in the process of returning the screen and getting another one, but i am still worried if I will be going through the same issue. One thing I didn't like about the phone is the cheap trashy components. So easy to brake and not made to be worked on.
I think I found the problem.
Well. Taking a closer look at the ribbon cable for the LCD and it appears to be the same color, but if you follow the lines, it does not look the same. I am currently waiting on a screen from a different seller and hoping to be the right one. I will keep you updated as I go forward.
Too many views, but no comment. I just hope this post going to help someone in the future. Keep in mind that sellers doesn't specified the kind of the LCD which is creating the troubles.
I am going to attach some photos to make it little clear. Keep in mind that I have HTC One for AT&T USA.
Did you ever replace the screen? I need to take mine apart and put a new battery and USB port in it. I'd like to know how pulling the screen went for you, if it was done.
xartic12 said:
Did you ever replace the screen? I need to take mine apart and put a new battery and USB port in it. I'd like to know how pulling the screen went for you, if it was done.
Click to expand...
Click to collapse
Not that good. I watched a YouTube video that helps a Little. You have to be really careful. Watch it and let me know if you need any additional help. Removing a broken screen not that bad since its broken. Be really careful when you order your new screen because I am having trouble to fine the right one. Mine PN: 60H00741-00P . There are many PN: 60H00742-02M that aren't working for me.
Forgot the video links
To disassemble : http://www.youtube.com/watch?v=qZFAsgjCunc
To reassemble: http://www.youtube.com/watch?v=S5KNmDeJ4Ww
medoo313 said:
Not that good. I watched a YouTube video that helps a Little. You have to be really careful. Watch it and let me know if you need any additional help. Removing a broken screen not that bad since its broken. Be really careful when you order your new screen because I am having trouble to fine the right one. Mine PN: 60H00741-00P . There are many PN: 60H00742-02M that aren't working for me.
Click to expand...
Click to collapse
The problem I have isn't the screen, but rather the battery and the USB port.. I have found both for about $20 each, but just didn't want to trash a basically brand new HTC.
Did you use a suction cup or pry it out?
xartic12 said:
The problem I have isn't the screen, but rather the battery and the USB port.. I have found both for about $20 each, but just didn't want to trash a basically brand new HTC.
Did you use a suction cup or pry it out?
Click to expand...
Click to collapse
I used a plastic sharp tool and you need to find the spots where you have to press on it to get it released. If you look at the first video, you will see where he marked it. those are the lock tabs that hold the assembly. The worst could happen is you may put a few dents in the plastic frame. You can order this part for around $20. A suction cup may works for you as well. Consider giving it little heat to lose the adhesive. Let me know if you still have any further questions.
Good luck
Where to get the right LCD in USA
I finally found a good supplier in USA for the proper kind of LCD. I spoke to him on the phone and I sent some pictures of my LCD. He has LCD part number 60H00741-00P that I been looking for. The website is https://www.gounlock.com/ If you ever call, ask for Jacky.
Hello XDA Community!
I seem to be having a serious issue with my phone and cannot seem to find a solution online, so I am hoping that someone here will be knowledgable enough to assist me!
When I slide my keyboard out on my sk17i, my screen refuses to change orientation or respond to my touches. Having tested this further, it seems that it is the screen itself that will not change, but keys pressed and touches are registered. I have figured out that I can slide the keyboard out about 40% (just over the bottom row of letters) and the screen seems to change orientation to landscape AND responds visually to my touches. Any more than that and it just stops.
I looked online and someone suggested passing a magnet (fridge) over the keyboard. I did that and it worked once for about a minute. After that it returned to this state and there doesn't seem to be anything I can do about it. I have just put in an order for new facias and a new hardware keyboard to repair it as I have had it since the day it was released and some components are getting on a bit.
Does anyone know what the issue is? I only can think of one thing and that is a flex cable issue, but I cannot be sure at all...
I'd appreciate any help that can be given!
At first glance, yes, seems like a flex cable/ribbon issue. You screen will remain frozen when the keyb is completely open because the framebuffer stops receiving signal from the motherboard. It wont take long until your screen shows artifacts or goes completely blank even when the keyb is closed. Your touch digitizer might also be affected by a bad flex cable.
I suggest you replace it as soon as possible, but don't try to do it yourself unless you have experience repairing phones. I tried to do mine and ruined the LCD display, making my repair cost three times as much
PD: magnet over the keyb? never heard of that.
Pixelado said:
At first glance, yes, seems like a flex cable/ribbon issue. You screen will remain frozen when the keyb is completely open because the framebuffer stops receiving signal from the motherboard. It wont take long until your screen shows artifacts or goes completely blank even when the keyb is closed. Your touch digitizer might also be affected by a bad flex cable.
I suggest you replace it as soon as possible, but don't try to do it yourself unless you have experience repairing phones. I tried to do mine and ruined the LCD display, making my repair cost three times as much
PD: magnet over the keyb? never heard of that.
Click to expand...
Click to collapse
Many thanks for that! The flex cable is out of stock right now, so that is quite worrying, I hope it lasts the next month or so! I think I should be okay with repairing it, since I've worked with very small and delicate electronics before in Engineering. Just will have to be super extra careful! Any advice about what to watch out for?
And yup, magnet seemed to work once, I saw it on a very old thread, but that was the only advice given there.
Well, good luck! Be extremely careful with the display though, the original display assembly has unprotected corners and borders on the LCD so it's very easy to break it, especially on the lower side near the softkeys. Replacement parts often come with plastic and/or metallic protectors on them, which help keeping the LCD safe. Guess SE never meant for people to crack the phone open hehe.
again, good luck with that.
Pixelado said:
Well, good luck! Be extremely careful with the display though, the original display assembly has unprotected corners and borders on the LCD so it's very easy to break it, especially on the lower side near the softkeys. Replacement parts often come with plastic and/or metallic protectors on them, which help keeping the LCD safe. Guess SE never meant for people to crack the phone open hehe.
again, good luck with that.
Click to expand...
Click to collapse
Aah okay! I guess I shouldn't bother replacing the facia then, don't want to break the screen! Thank you once again!
Well, all my parts have now arrived, so tonight I'll be attempting this! Hopefully this goes well and fixes the problem!
ECGadget said:
Well, all my parts have now arrived, so tonight I'll be attempting this! Hopefully this goes well and fixes the problem!
Click to expand...
Click to collapse
Best of luck to you, mate.
Replacing a flex ribbon/cable on the mini pro is no easy task, requires patience and steady hands when sticking the big square part onto the metallic slider while making sure all of the other components (home button, camera, led and sensors) keep aligned in place. Do it wrong and you're in for an even more tedious mission haha.
PD: here's a crappy pic from when I did mine
Pixelado said:
Best of luck to you, mate.
Replacing a flex ribbon/cable on the mini pro is no easy task, requires patience and steady hands when sticking the big square part onto the metallic slider while making sure all of the other components (home button, camera, led and sensors) keep aligned in place. Do it wrong and you're in for an even more tedious mission haha.
PD: here's a crappy pic from when I did mine
Click to expand...
Click to collapse
Thanks for that! I was just struggling to take the motherboard off, and looking at the picture helped me see where I could try to pry it open!
Yeah, the mobo can be a b*tch to take off. Glad I could help. Be sure to tell us how it goes.
Pixelado said:
Yeah, the mobo can be a b*tch to take off. Glad I could help. Be sure to tell us how it goes.
Click to expand...
Click to collapse
Well, after a cracked front facia (thanks to the previous repair that I had on it two years ago), and my temperamental lights, my phone works a charm! Replaced the flex cable, motherboard mount and hardware keyboard. Once again, thank you so much for your advice, I have decided to hang around this place much more often!
Repaired two years ago? Wow, your phone is kind of a veteran haha, mine is about to turn 2yo in about two months. Gotta get a birthday cake.
Good to know everything went fine. See you.
Pixelado said:
Repaired two years ago? Wow, your phone is kind of a veteran haha, mine is about to turn 2yo in about two months. Gotta get a birthday cake.
Good to know everything went fine. See you.
Click to expand...
Click to collapse
I've had my phone since two weeks before it was released in 2011 xD
I'm sure your phone will love the cake
Noticed a new glitch with my phone though... the softkey and keyboard lights start to light up when I switch the screen on, but as soon as the screen switches on the lights switch off?
Never heard of such problems. What rom are you on?
I am running a stock gingerbread 2.3.3 rom, just rooted it a year ago. No other changes, apart from shoving CWM onto it for backup/restore
Hey guys, I just saw this post after hours of frustration!, I recently changed my damaged slider mechanism on my sk17i and I had to transfer the ribbon cable from the one mechanism to the other but I glued it with 2mm adhensive that is used for screen, and the problem is when I open the phone it is always on landscape mode, like the phone thinks the keyboard is always out! Before I tried this repair
everything worked perfect
How the phone understands if the keyboard is out or not?
Please tell me what I could have done wrong, I would appreciate your help here!
Sorry for my bad english
Thank you in advance!!!
I've been trying to figure that out myself too, it seems to be some kind of optical sensor. Whatever it is, it just works for me hehe.
Pixelado said:
I've been trying to figure that out myself too, it seems to be some kind of optical sensor. Whatever it is, it just works for me hehe.
Click to expand...
Click to collapse
And you dissasembled it and re-assembled with no problems?
r3izor said:
And you dissasembled it and re-assembled with no problems?
Click to expand...
Click to collapse
Welcome to XDA.
Like Pixelado said, it is probably an optical sensor. My advice would be to disassemble the phone again (without unsticking the flex cable though) and make sure everything is back in its correct place. It make just be something is a little out of place, which is very easy to do! Good luck!
r3izor said:
And you dissasembled it and re-assembled with no problems?
Click to expand...
Click to collapse
Yes sir. I have never re-used a flex ribbon though. I removed the broken factory ribbon and stuck a new one in. No problems.
Pixelado said:
Yes sir. I have never re-used a flex ribbon though. I removed the broken factory ribbon and stuck a new one in. No problems.
Click to expand...
Click to collapse
Then as long as I dont know where the sensor is in order to find out my mistake, I am afraid my phone will be permanently on landscape :crying:
Thank you for your replies guys!