Related
Here is a breakdown of what i did and whats happening.
1.2 ollipro installed already
loaded new radio
loaded new rom
Now the windows mobile 6.1 screen would come up and ask to tap screen but would reboot at this screen continously. I assumed this was happening because 1.2 ollipro was installed and not 2.4.
I then decided to reinstall my old radio and old rom and now the phone gets to the htc bootscreen and reboots immediately over and over again without getting far at all. What do I do?
For TELUS P4000
BOOTLOAD MODE
1. Try getting to the BOOTLOAD MODE by pressing POWER, CAMERA and RESET all a the same time
2. You should see at screen with red green blue white
New RADIO and CE ROM
1. Hard-SPL-240-MFG.exe/titan_SPL_2.40-olipro.exe (follow the instructions)
2. Run titan_radio_3.35.04.exe (very simple GUI instructions)
3. The titan will reboot by it's self, put it back in BOOTLOAD MODE
4. Extract dcd_titan_kitchen_3.0.0.rar to a directory and run BuildNB.bat (it takes a couple of min)
5. Select the stuff you want and don't forget you carrier (TELUS....)
6. Press the PLAY button (when finished, which is hard to see, when play is green) close the BuildOS
7. In a DOS windows it will build the CE ROM (follow the instructions)
8. Titan will reboot
i cant get 2.4 on there because i can get activesync up and when i get it to run through the boot load it gets to 100% in a split sec but leaves 1.2 on and not 2.4 even though it didnt record any errors
I'm having the exact same problem. Got the new Rom and radio installed. I had to go back to 1.2 to do it. But now i cant get 2.4 to install. I run the program it seems to install but still says 1.2 and is stuck on bootloader screen. even though it said itupdated to 2.4 anyone got any ideas on how to get 2.4 on there?
Try entering the Bootloader mode of Oliprio 1.20 and connect the USB to your computer.
Although it wont start an Active Sync session it will still allow you to load thing on such as a ROM or flashing program.
Well once you are in Bootloader and have a USB connection then try installing Oliprio 2.40
This might work.
Hi, ive done that and gone through the 2.4 install. after the RUU runs the progress bar goes across in like 1 second. it reports it successful but it still says 1.2 and is now stuck in the 1.2 bootloader. as if 2.4 never installed. any suggestions?
Furman69 said:
Hi, ive done that and gone through the 2.4 install. after the RUU runs the progress bar goes across in like 1 second. it reports it successful but it still says 1.2 and is now stuck in the 1.2 bootloader. as if 2.4 never installed. any suggestions?
Click to expand...
Click to collapse
So you installed 2.40. Well once you installed 2.40 go into bootloader again and make sure it is 2.40 and then try flashing the Radio first and then the ROM.
This is how i did it:
Installed olipro 1.2
installed radio 3.35
installed dcd sprint 3.0
Now like everyone else it continually reboots cause of olipro 1.2. So i put it in bootloader and it says 1.20 spl. So now i go to install 2.4 Olipro. RUU runs and the progress bar goes to 100% in about 3 secs. AFter it goes to 100% the mogul screen flashes and it says olipro 1.2 as if 2.4 didnt install even though on my comp it says that ruu update was sucessful. So im confused. I have tried it on my computer(vista64) and my old one xp 32bit. When the batch file is running it says "no device connected. would you like to try again?" w/ a yes/no/cancel. If i hit yes it just loops. if i hitno it will ask me this about 4 times then RUU will load
Ok, for anyone stuck with an older version of olipro and the new radio:
While in the bootloader, load an earlier version of your carriers rom. This should let you boot again and will let you install the newest 2.4 olipro bootloader so you can flash the newer roms.
If you can't find an earlier version of your carriers rom you will need to find an older radio rom and an older custom rom and flash both seperately to get it to boot.
Furman69 said:
This is how i did it:
Installed olipro 1.2
installed radio 3.35
installed dcd sprint 3.0
Now like everyone else it continually reboots cause of olipro 1.2. So i put it in bootloader and it says 1.20 spl. So now i go to install 2.4 Olipro. RUU runs and the progress bar goes to 100% in about 3 secs. AFter it goes to 100% the mogul screen flashes and it says olipro 1.2 as if 2.4 didnt install even though on my comp it says that ruu update was sucessful. So im confused. I have tried it on my computer(vista64) and my old one xp 32bit. When the batch file is running it says "no device connected. would you like to try again?" w/ a yes/no/cancel. If i hit yes it just loops. if i hitno it will ask me this about 4 times then RUU will load
Click to expand...
Click to collapse
Instead of running the RUU right after installing 2.4 over 1.2 try canceling the RUU and then manually enter bootloader mode in 2.4 and then install the RADIO following the ROM.
I figured it out. feel kinda stupid. was trying to install 2.4 from the boot loader of 1.2 forgetting that it needs to install files over to the phone before it flashes. :/ thanks foryour help though
Furman69...
I'm having the same problem. Could you post a step by step?
Thanks
I think I bricked it.
Actually I think I made a bigger mistake. I'm a VZW user, and I flashed the sprint/htc update hoping I could just flash dcd on top of that = stupid. The radio settings were all f-ed up. So I believe I read in the dcd 3.0.0 thread to run the titan relocker and then flash the stock vzw rom. Big mistake. Once I relocked it, It wouldnt let me flash vzw 2.09 and now my phone's in bootloader saying
TITA100
SPL-1.06.0000
CPLD-9
I think I'm screwed because It doesnt have a rom on there, so I can even unlock it. Any help would be greatly appreciated.
Flashing the sprint update, then flashing dcd on top of it would have been completely fine if you didn't let the sprint customizations run...i've done it to 3 phones already.
I don't really get what you're saying though. Are you stuck in the bootloader? Can you boot into any kind of rom? What happens if you try and soft reset, does the phone do anything?
gcincotta said:
Flashing the sprint update, then flashing dcd on top of it would have been completely fine if you didn't let the sprint customizations run...i've done it to 3 phones already.
I don't really get what you're saying though. Are you stuck in the bootloader? Can you boot into any kind of rom? What happens if you try and soft reset, does the phone do anything?
Click to expand...
Click to collapse
Yeah I wasn't that smart though . But yeah I'm stuck in bootloader. And I don't even know how to go about putting a ROM on there because it's locked. I've already tried to redo the Sprint/HTC 3.35 update, but to no avail. It says wrong vendor. I don't know... It's brand new too, that what sucks about it.
I finally got it to work after going back and forth installing old roms and radios and then installing 2.4 and then the radio and rom as ususal.
To be honest with you guys i beat myself up because i should of done it like this from the get go 2.4,radio, rom, and thats it but i read about people having trouble and dcds post, and I just went through more trouble that way. Thanks for the help.
If you're stuck in the bootloader, download the exitbl program to forcefully exit the bootloader. This will reset the phone. Tell me what happens after that. Does it boot any sort of rom? Does it just hang at a blank screen? Let me know.
Jaquers said:
Actually I think I made a bigger mistake. I'm a VZW user, and I flashed the sprint/htc update hoping I could just flash dcd on top of that = stupid. The radio settings were all f-ed up. So I believe I read in the dcd 3.0.0 thread to run the titan relocker and then flash the stock vzw rom. Big mistake. Once I relocked it, It wouldnt let me flash vzw 2.09 and now my phone's in bootloader saying
TITA100
SPL-1.06.0000
CPLD-9
I think I'm screwed because It doesnt have a rom on there, so I can even unlock it. Any help would be greatly appreciated.
Click to expand...
Click to collapse
I had a similar experience. Here is what I did.
I had the following installed before I started.
2.40 bootloader
3.27 radio
DCD 2.3.2 rom
I wanted to upgrade to the latest and greatest so I did the following. (This was before anyone knew about the 2.40 radio flashing issues.)
Flashed to DCD 3.00.
Failed Trying to flash 3.35 radio.
Read some more and like you tried to relock my phone using titanrelocker
Locked bootloader
Failed trying to flash Verizon Radio (downloaded from ppcgeeks.com)
Failed trying to flash Verizon Rom 2.09 (downloaded from ppcgeeks.com)
So at this point I was stuck in the original 1.06 Verizon locked bootloader, but I had 3.27 radio and DCD 3.00 rom.
Execed titan_exitbl.exe (included in 2.40 bootloader) in vista which returned a nice error. (Error accessing USB blah blah blah)
Execed titan_exitbl.exe in XP with ActiveSync and phone rebooted
Phone booted into Windows Mobile 6.1 and rebooted itself.
So I plugged the mini USB cable back in hopeing it might prevent it from rebooting. Luckily it did.
Reunlocked Bootloader using 1.20 olipro
Flashed 3.35 Radio
Flashed 3.00 DCD Rom again. (Just in case)
Phone booted into Windows Mobile 6.1 with mini usb cable still plugged in.
Upgraded bootloader to 2.40.
Re-Insert my NAM settings into EPST and rebooted.
*228 to get latest PRL.
Has been rock solid since.
So I was in the middle of upgrading to the "Official Sprint Rom" using 1.2Olipro in order to jump on the DCD 3.0.1 bandwagon. I guess this was a bad idea because the phone rebooted at 11% and now I'm back to the bootloader. The problem is, I don't know what to do. I don't want to make things worse so for now I just left it in the bootloader.
Prior to attempting the flash I was running
DCD 2.0.0 /w Radio 3.27 (2.4Olipro).
Just before I flashed the Sprint rom I flashed the 1.2 bootloader.
I'm stuck, what do I do now?
Tom
check this link out:
http://forum.ppcgeeks.com/showthread.php?t=17667
You didnt need to install olipro 1.20. Install olipro 2.40 again and you will get your device bootable again.
You may find that you have fried your radio. when the device reboots after the olipro 2.40 is back on you can check the message on the first screen to see if the radio is there or not. If there is no radio just reflash sprint 3.35. If the radio is there the device will reboot into your old configuration.
Then just flash the sprint offical 3.35 and this will give you then new radio. Then flash dcd 3.x.x
The instructions are right in the first few posts of the 3.0.1 thread.
I can't install 2.4 because it requires an activesync connection. The phone is currently in bootloader so no activesync. Should I reboot the phone? I don't want to make a bad situation worse.
Tom
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
You might have to flash a radio and rom via sd card method. The radio and roms will have to be compatible with olipro 1.20 otherwise it will continually reboot once it is all flashed.
I am sure there is a method to get you back to olipro 2.40 without activesync so you might search a bit first. But if you cant find out how, then the sd method above will at least get you back working.
Unfortunately dropping back to a non gps radio (compatible with olipro 1.20) will probably hose your MSID etc so I hope you wrote them down.
Anyone more knowledgeable than me might comment further but do a bit of searching in the meantime.
friguy33 said:
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
Click to expand...
Click to collapse
I have 2 .exe's:
Hard-SPL-MFG.exe and titan_SPL_2.40-olipro.exe
when I run either:
*
* P4000/PPC6800/xv6800/Titan/Mogul UnLocker utility
*
* Total process may take about 5-10 minutes depends on CPU speed.
*
Connect your device via activesync before continuing.
Press any key to continue . . .
Initializing
When you reboot, do you get a screen telling you the bootloader, radio and rom versions?
To exit bootloader to check, you can use ImCoKeMaNs exit bootloader program.
SOLVED!
I was able to flash Sprint v2.09 ROM. After the phone rebooted and the Calibration screen came up I was able to upgrade to Olipro 2.4. Right after that I ran the 3.35 Sprint update which went through. As soon as Windows was back at the calibration screen, I went back into 2.4 bootloader and ran the DCD upgrade. Up 100% and incoming calls work so it looks like the MSID was preserved.
Cheers,
Tom
Hello everyone i Just got a xv6800 and am trying to flash to a newer rom...However i cant seem to boot into the bootloader it just hangs at Loading.... There is nothing installed its factory rom and settings
Thx in advance
How are you attempting to load into bootloader?
The way I saw on the forums....holding power and camera button and hittig the reset..i get the tri color screen then it goes to Loading... and just sits there dosnt do anything else
Do you have a microsd card in while trying this? If so, does it contain any .nbh files on it in the root directory? If so, do you have a TITAIMG.nbh file in the root directory?
The only way the bootloader would try loading something the way you're describing is if this is the case.
I agree with gcincotta.
If you are in fact trying to flash from the SD card though, most people have reported that it won't work using an SDHC card. It needs to be a standard (non high-capacity) card.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Well i got it to go to usb but now the .exe file for the 2.40 unlocker wont run on x64 systems so i guess im out of luck huh
Did you already run the unlocker? If so, you should be ready to flash a custom ROM. It is normal to be stuck in the bootloader after an unlock. Just flash away.
If the unlock did not go successfully, you will have to try again, making sure to follow directions precisely (on a 32bit system preferably, less headaches). To unlock you must be booted up into Windows Mobile. You can try the exit bootloader program from the PPCGeeks Titan Upgrade forum, or try flashing a stock ROM to get back into WM.
Edit: You can tell if the unlock was successful by looking at the SPL in the bootloader (right under TITA100 MFG). It should now say SPL-2.40.Olipro. If it does not, try the steps above to get back into Windows Mobile.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Click to expand...
Click to collapse
You need to be more specific. Everyone's titan says TITA100. What SPL is installed? Post the entire contents of your screen and then we can get somewhere.
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
I was able to udate to 2.52 rom...the 3.04 wasnt working correctly and it would not up date using *228..and there was no sound...i was not using the radio 3.35 because i heard people saying that it was a bad one to use...is there much difference in performace between 2.52 and the 3.04?
So I need to install Sprints 3.35.651.2 rom and not let the sprint customazations run.
Then use the unlocker 2.4
Then use DCD or No2Chem custom rom.
craig540 said:
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
Click to expand...
Click to collapse
You are starting from scratch with an unlocked phone. Before rushing forwards you have some reading to do:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
All of your answers are there.
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
craig540 said:
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
Click to expand...
Click to collapse
1st- update to 2.4 olipro
2nd- update sprint 3.35 rom (stop at the "tap the screen" customization screen) this gives you the radio
3rd- from customization screen start the 3.0.4 rom and flash that rom
Your phone will restart after loading and will boot into wm6.1
4th- Read untill you understand before flashing roms
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
craig540 said:
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
Click to expand...
Click to collapse
Does not matter, if you do it in rom it will force into bootloader anyway.
Ok up and running dcd 3.04
date 2-22-08
radio 3.35.04
I did not let sprint cutomazation run.
Tried to make a call and get message saying verizon can not authenticate and to dial #8899
Should I do that now?
Had to call VZW to get new A-Key
No GPS detected in google maps is there anything I need to do to set it up ?
Try installing VisualGPSce -- it's a good little & free diagnostics program too see GPS satellite reception.
....after seeing that running on COM4 at 4800 baud, then you should see a list of visible satellites. Now, whether or not you get a sufficient lock within the first half hour depend's upon your luck in the draw for a GPS functioning Titan -- GPS hardware-wise, not all are equal.
i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?
thanks
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
belmont said:
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
Click to expand...
Click to collapse
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
scrosler said:
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
Click to expand...
Click to collapse
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
belmont said:
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
Click to expand...
Click to collapse
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
scrosler said:
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
Click to expand...
Click to collapse
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
belmont said:
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
Click to expand...
Click to collapse
Hmmm, maybe try a different USB port at this time. Also, try this...
Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.
In XP I beleive it will show up under USB at the very bottom of Device Manager.
Does the phone show up at all?
Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....
You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....
..................................
Check your current bootloader
1. Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
2.
Hit POWER-CAMERA-RESET to check what version of bootloader you have installed.
* At the tri-colour bootscreen you will see the version number installed.
* if it is 1.04 or 1.06 then your Titan is locked and has the correct bootloader to flash to the stock ROM of your choice --> skip to step III
* if it is 1.20, 2.40, or 2.47 then your phone is unlocked with a third party bootloader and must relock your phone.
---------------------------------------------------------------------------
I have a Sprint HTC Mogul and have been shuffling through all the threads and still confused, sort of...
I am at the Tri-color screen and none of those version number matches mine.
on my tri-color screen it displays:
Tita100
SPL-2.06.0000
CPLD-9
i searched the board and found but it didnt give me a clear answer.
http://forum.xda-developers.com/showthread.php?t=284404
So far i have downloaded
Sprint Cab
dcd_titan_3.2.5.exe
Titan_Radio_ROM_3.42.40.exe
[OliPro MFG 2.40] (Hard SPL)
I'm hoping someone can help me figure this out, whether or not i need to downgrade/upgrade.
And Also was wondering what type of neat things i can do with the roms/kitchen im a total noob at this but trying to make sense of all of this.
Other Phone info:
rom Version 3.35.651.2
radio ver. 3.35.04
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
scrawnyb said:
flash back to a stock (non-GPS if I remember right) ROM from there.
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
You are right on the money.......
that should be the stock bootloader for a stock gps rom.
if you want a custom rom you will need to unlock using 2.40 or 2.47.
kitchens just allow you to cook in apps that you want instead of installing them later. the problem is the install is permanent and they cannot be removed.
i prefer to flash a clean rom and install my apps later.
im pretty sure 2.06 is the temporary bootloader used by no2chem's nueSPL to ram with 2.47. if your bootloader shows 2.06 you will need to flash nueSPL again as it did not flash correctly. 2.07 is nueSPL Relocker.
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
lafester said:
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
Click to expand...
Click to collapse
it happened to me, although i didnt get stuck. it was flashed on a card that isnt flashing compatible (telus). i only noticed because it didnt reset itself like it said it should have. returned the card, got a San Disk, and reflashed nueSPL. this time it soft reset itself, and displayed the correct bootloader, 2.47.
I got stuck in 2.06 last night... earlier in the day I dropped my mogul in water and somehow cracked the screen at the same time. After drying everything out for 12 hours the phone came on with barely anything on the screen, I got the phone into bootloader (it was at 2.47) flashed a stock sprint rom, I immediately ran the nueSPL relocker (had to use my mobler to see the screen), after the relocker ran I was stuck in a 2.06 bootloader for some time, eventually I got out of the bootloader (not quite sure how... I flashed the stock sprint rom a few more times and mash some buttons) eventually I was able to run the relocker again and get my phone back to 2.07... a little bit of trouble but it was worth it now that I know I should have absolutely no problems getting a new (probably refurb) phone through TEP
scrawnyb said:
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
My phone is stock, i hadnt done anything to it yet. Im just unsure what to do because 2.06 was not shown at the step-by-step instructions.
so let me see if i understand what i need what to do....
flash the current rom, stock 2.06, with [OliPro MFG 2.40] (Hard SPL)
then run dcd_titan_3.2.5.exe and Titan_Radio_ROM_3.42.40.exe
then Sprint Cab??
Thanks for the replys