i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?
thanks
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
belmont said:
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
Click to expand...
Click to collapse
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
scrosler said:
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
Click to expand...
Click to collapse
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
belmont said:
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
Click to expand...
Click to collapse
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
scrosler said:
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
Click to expand...
Click to collapse
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
belmont said:
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
Click to expand...
Click to collapse
Hmmm, maybe try a different USB port at this time. Also, try this...
Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.
In XP I beleive it will show up under USB at the very bottom of Device Manager.
Does the phone show up at all?
Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....
You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....
..................................
Related
So I was in the middle of upgrading to the "Official Sprint Rom" using 1.2Olipro in order to jump on the DCD 3.0.1 bandwagon. I guess this was a bad idea because the phone rebooted at 11% and now I'm back to the bootloader. The problem is, I don't know what to do. I don't want to make things worse so for now I just left it in the bootloader.
Prior to attempting the flash I was running
DCD 2.0.0 /w Radio 3.27 (2.4Olipro).
Just before I flashed the Sprint rom I flashed the 1.2 bootloader.
I'm stuck, what do I do now?
Tom
check this link out:
http://forum.ppcgeeks.com/showthread.php?t=17667
You didnt need to install olipro 1.20. Install olipro 2.40 again and you will get your device bootable again.
You may find that you have fried your radio. when the device reboots after the olipro 2.40 is back on you can check the message on the first screen to see if the radio is there or not. If there is no radio just reflash sprint 3.35. If the radio is there the device will reboot into your old configuration.
Then just flash the sprint offical 3.35 and this will give you then new radio. Then flash dcd 3.x.x
The instructions are right in the first few posts of the 3.0.1 thread.
I can't install 2.4 because it requires an activesync connection. The phone is currently in bootloader so no activesync. Should I reboot the phone? I don't want to make a bad situation worse.
Tom
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
You might have to flash a radio and rom via sd card method. The radio and roms will have to be compatible with olipro 1.20 otherwise it will continually reboot once it is all flashed.
I am sure there is a method to get you back to olipro 2.40 without activesync so you might search a bit first. But if you cant find out how, then the sd method above will at least get you back working.
Unfortunately dropping back to a non gps radio (compatible with olipro 1.20) will probably hose your MSID etc so I hope you wrote them down.
Anyone more knowledgeable than me might comment further but do a bit of searching in the meantime.
friguy33 said:
you dont need active sync, put in bootloader and plug it into the computer and run the bootloader upgrade...should work
Click to expand...
Click to collapse
I have 2 .exe's:
Hard-SPL-MFG.exe and titan_SPL_2.40-olipro.exe
when I run either:
*
* P4000/PPC6800/xv6800/Titan/Mogul UnLocker utility
*
* Total process may take about 5-10 minutes depends on CPU speed.
*
Connect your device via activesync before continuing.
Press any key to continue . . .
Initializing
When you reboot, do you get a screen telling you the bootloader, radio and rom versions?
To exit bootloader to check, you can use ImCoKeMaNs exit bootloader program.
SOLVED!
I was able to flash Sprint v2.09 ROM. After the phone rebooted and the Calibration screen came up I was able to upgrade to Olipro 2.4. Right after that I ran the 3.35 Sprint update which went through. As soon as Windows was back at the calibration screen, I went back into 2.4 bootloader and ran the DCD upgrade. Up 100% and incoming calls work so it looks like the MSID was preserved.
Cheers,
Tom
Hello everyone i Just got a xv6800 and am trying to flash to a newer rom...However i cant seem to boot into the bootloader it just hangs at Loading.... There is nothing installed its factory rom and settings
Thx in advance
How are you attempting to load into bootloader?
The way I saw on the forums....holding power and camera button and hittig the reset..i get the tri color screen then it goes to Loading... and just sits there dosnt do anything else
Do you have a microsd card in while trying this? If so, does it contain any .nbh files on it in the root directory? If so, do you have a TITAIMG.nbh file in the root directory?
The only way the bootloader would try loading something the way you're describing is if this is the case.
I agree with gcincotta.
If you are in fact trying to flash from the SD card though, most people have reported that it won't work using an SDHC card. It needs to be a standard (non high-capacity) card.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Well i got it to go to usb but now the .exe file for the 2.40 unlocker wont run on x64 systems so i guess im out of luck huh
Did you already run the unlocker? If so, you should be ready to flash a custom ROM. It is normal to be stuck in the bootloader after an unlock. Just flash away.
If the unlock did not go successfully, you will have to try again, making sure to follow directions precisely (on a 32bit system preferably, less headaches). To unlock you must be booted up into Windows Mobile. You can try the exit bootloader program from the PPCGeeks Titan Upgrade forum, or try flashing a stock ROM to get back into WM.
Edit: You can tell if the unlock was successful by looking at the SPL in the bootloader (right under TITA100 MFG). It should now say SPL-2.40.Olipro. If it does not, try the steps above to get back into Windows Mobile.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Click to expand...
Click to collapse
You need to be more specific. Everyone's titan says TITA100. What SPL is installed? Post the entire contents of your screen and then we can get somewhere.
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
I was able to udate to 2.52 rom...the 3.04 wasnt working correctly and it would not up date using *228..and there was no sound...i was not using the radio 3.35 because i heard people saying that it was a bad one to use...is there much difference in performace between 2.52 and the 3.04?
So I need to install Sprints 3.35.651.2 rom and not let the sprint customazations run.
Then use the unlocker 2.4
Then use DCD or No2Chem custom rom.
craig540 said:
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
Click to expand...
Click to collapse
You are starting from scratch with an unlocked phone. Before rushing forwards you have some reading to do:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
All of your answers are there.
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
craig540 said:
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
Click to expand...
Click to collapse
1st- update to 2.4 olipro
2nd- update sprint 3.35 rom (stop at the "tap the screen" customization screen) this gives you the radio
3rd- from customization screen start the 3.0.4 rom and flash that rom
Your phone will restart after loading and will boot into wm6.1
4th- Read untill you understand before flashing roms
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
craig540 said:
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
Click to expand...
Click to collapse
Does not matter, if you do it in rom it will force into bootloader anyway.
Ok up and running dcd 3.04
date 2-22-08
radio 3.35.04
I did not let sprint cutomazation run.
Tried to make a call and get message saying verizon can not authenticate and to dial #8899
Should I do that now?
Had to call VZW to get new A-Key
No GPS detected in google maps is there anything I need to do to set it up ?
Try installing VisualGPSce -- it's a good little & free diagnostics program too see GPS satellite reception.
....after seeing that running on COM4 at 4800 baud, then you should see a list of visible satellites. Now, whether or not you get a sufficient lock within the first half hour depend's upon your luck in the draw for a GPS functioning Titan -- GPS hardware-wise, not all are equal.
Hi there, I have very minimal experience with this stuff so I will provide as much detail as possible...
I had previously successfully programmed my HTC6800 back in March by unlocking with Olipro 2.4, then I flashed the radio with 3.27 and used dcd 2.3.2 for Bell on it. Now my memory is a little foggy as that was several months ago however I made it through the process fine. This encouraged my to try to update again today. I tried following the steps in the wiki as I could not find the guide I had used previously. I already had Olipro 2.4 so I was good at that step. I then tried running the newest radio update and it would not take. It gave me an error. I reset the phone and tried several times but to no avail. I then tried putting on dcd3.2.0 which went fine. THe phone rebooted and I made a test call and everything was fine. I however wanted the new radio update still so I thought I'd take another crack at it... it still would not update. In the wiki it said about relocking the phone and putting it back to the factory ROM and starting again. So I did this, I downloaded the relocking util and followed the instructions to relock the phone. That went fine... Olipro is gone and is shows the 1.06 like it's supposed too... next it said to put the factory ROM back on... well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
So currently my 6800 sits as the 3 colour screen with 1.06 relock on it and does nothing else. It has radio 3.27 on it and dcd 3.2.0.
Is there any way to fix this?????
Run this first to exit the bootloader and get into windows mobile. Then check out which rom you are on (I think you were on dcds rom). Then load radio via sd card method listed in the wiki. Then reload dcd if you are not already on the version that you want.
P.S. I have heard things about that ROM that it caused problems. You may want to read up on that here.
Nope
Well, I downloaded the file and tried running it but to no avail. It just comes up saying that the application failed to start because RAPI.DLL is missing.
Also
I tried running that app on a Vista machine as well and it just says that it can't open the USB port. However, windows found the device and installed a driver for it when plugged in AND it shows USB on the bootloader screen when plugged in.
ok..,. let me see...
try installing olipro 2.40 again, it seemes that your phone is locked (olipro 1.06) so it can't run the dcd custom rom... reset and see if you can enter windows...
then if you enter windows normally, downgrade to olipro 1.20 and install the new radio, then, once again upgrade to olipro 2.40 so it can enter windows...
let me know if it worked for you...
Evo69 said:
well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
Click to expand...
Click to collapse
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Here's the problem
OK. Here's the problem. I obviously misread the instructions on setting the unit back to stock as I just read them again and I realize my mistake. I did not load the stock ROM on first. I used the Re-lock program and re-locked my unit before putting the stock ROM back on. So I sitting at the 3 colour screen with SPL 1.06 and I have radio 3.27 on the unit and dcd's latest ROM on it. I can't get it past the 1.06 bootloader. I have tried a hard reset, I have tried the program above to exit the boot loader and it does not work. Is there any way I can get Olipro 2.4 back on or exit this bootloader???
just connect your phone to the computer (it's ok to be on the tri color screen) and install olipro 2.40 from the computer...
you just need to be sure that when you connect the phone in the tri color screen it says USB...
i'm attaching Olipro 2.40
No Dice
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
i had a similar problem yesterday when i tried to upgrade the radio form 3.42.02 to 3.42.30 and taht solved my problem...
so you basically cannot exit the bootloader mode?? even when you hard reset your device??
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Evo69 said:
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
Click to expand...
Click to collapse
I have the Bell ROM if you're looking for it.
TS
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
jhamilton said:
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
Click to expand...
Click to collapse
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
YES
Timeshell said:
I have the Bell ROM if you're looking for it.
TS
Click to expand...
Click to collapse
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Keystone said:
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Click to expand...
Click to collapse
I tried using a Sprint one... it would not work.
Timeshell said:
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
Click to expand...
Click to collapse
Yeah I've heard some horror stories when it came to downgrading, including a few bricked devices.
http://forum.ppcgeeks.com/showthread.php?t=26082
I would be interested to know if anyone on Bell has managed to successfully downgrade a 6800 to stock.
i thought dcd's new 3.2.0 needed a radio of 3.35 or higher to run and does not flash the radio when u flash his rom. Another problem with the phone not coming out of the bootloader is that you have to disable usb connections in active sync or windows mobile device center for the exit bootloader app to work. Try disabling the usb connection in whichever one applies for you and run the app again. If you can get out of the bootloader try to go back to ollipro 2.40 or use one of no2chems bootloaders as they work from the device and an sd card no need for a pc to flash the bootloader. once bootloader is unlocked again run a full radio/rom update like the sprint stock 3.35 easily found on htc's website under the titan (us version of the site). Don't let the carrier custimizations run ... the file that runs after u calibrate screen and set timezone just pull the battery. Then grab whatever rom / radio you want to or were trying to flash 2 before and name it put it on the root of an sd card (thats under 2gb and formatted to fat32) and rename the ruu_sighned.nbh file to TITAIMG.nbh hold power + camera and hit your soft reset button. The tri color screen will come up and should say loading then promt to hit the power button to flash and show u what u r flashing. cdma (radio). os (radio rom) or splash screen, or whatever you r trying to flash hit power button to start once done it will sit with update complete on the screen pull the battery out for about 30 sec and put it back in reboot and enjoy the custom rom or radio.
kdj67f said:
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Click to expand...
Click to collapse
You can use nueSPL 2.47 to load the locker/relocker but you need to be booted into WM6 to do so. You need to reload another rom that uses the bootloader you have currently loaded and then you can move forward or backward.
Evo69 said:
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Click to expand...
Click to collapse
Uploaded to Rapidshare
http://rapidshare.com/files/1271390...3.666.1_RS_1.37.30_BM_1.27_0604_SHIP.zip.html
TS
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
I have not seen this... but my suggestion would be to do the Power + Camera + reset... and let it go into bootloader... then just reflash the rom.
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
Like the other guy said, force bootloader but take note of the version. Make sure you are running version 2.40 or greater. If you are running stock bootloader 1.06 or anything else it will have the reboot loop. Read the wiki in my signature fully before doing anything else. Did you read this before flashing?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5?????
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
paulash said:
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
This wiki tells you the steps.... I did it as follows... but... after doing the radio... you have to force it into the bootloader. It will not load into the phone rom.
xv6800 Rom Upgrade Instructions Wiki
gc14 said:
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
Click to expand...
Click to collapse
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
paulash said:
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
I put radio 3.42.30 on there but had to get HardSPL-2.40 on it first. The wiki explains it very well.
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
nitro66215 said:
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
Click to expand...
Click to collapse
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
scrawnyb said:
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
Click to expand...
Click to collapse
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
paulash said:
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
Click to expand...
Click to collapse
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
nitro66215 said:
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
Click to expand...
Click to collapse
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
paulash said:
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
Click to expand...
Click to collapse
It shouldn't be reverting back to 1.2. If you have 2.4 installed correctly... and you check with the "Reset"... then you can do the RUU update right from that bootloader screen. If it is 1.2... then attempt the 2.40 hard spl from that screen instead of redoing the stock rom.
nitro66215 said:
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
Click to expand...
Click to collapse
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
serfboreds said:
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
Click to expand...
Click to collapse
I don't agree that the USB / Activesync is 6 or 7 steps. I did 4 or 5 at the most.. and I'm counting the power+camera+reset as a step.
flash
When the bootloader screen comes up with 1.2, are you just assuming its done...or do you actually then keep clicking through the options until it actually flashes the phone with the ROM?
I currently have a Verizon Wireless fully flashed to cricket XV6800. I decided to know about hacking the Mogul so what I try to do was Look up WMDC 6.1 and apply it to my phone. When i did this the screen stopped at 11%. I took out the battery and tried to turn it on and i get a Red, Green, and Blue color on the start up screen. The words that are on the phone are TITA100 SPL-1.20.Olipro and on the bottom it says USB when connected and Serial when not connected. I looked every where to and figure it out how to get my phone back to the same way. I downloaded so many programs like Titan Unlocker, Titan exitbl, but all these programs do is say my phone is not connected when it is connected. I hear the Sound when the connection for the USB is connected and disconnected. What can i do Will i ever get my phone back to the same state that it once was. I was wondering also that since my phone was flashed that the software will be erased. Is there any way that I can get my Cricket Service. By the way before i did all the hacking what i did was back everything up on the memory card. Is there a way I can restore that through the phone even though i cant access the menu?
I'm going crazy--Thank you for your time to read and for those who can give me some word of advice or some way that my problem can be solved.
Thank you
if u are using xv6800.. i believe u have to install bootloader 2.40 or 2.47.. maybe that might be the problem when installing wm6.1
First, your phone is not bricked.. bricked means broken.. unfixable.. a brick!
You also need to let us know what you software you want to run... DCD 3.2.6?? WMDC 6.1 is Windows Mobile Device Center.. it's not a rom?? So I dont know what you tried to flash.
You need to read the instructions!! Sounds like You upgraded your rom (or tried to) with a non compatible bootloader.. if you dont want to bust your $200 - $500 phone perminently.. you should read the directions twice.. (I read them 4 times, then asked questions before the first time I flashed mine)
When you plug in the device and hear the usb sound.. check device manager.. make sure you see a usb device.. Your OS shoul have installed drivers... Then try the info below.
scrosler said:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
Click to expand...
Click to collapse
After that you can Flash a Radio, then a rom (I recommend the SD method)
And the versions in my signature.
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
You should also read this WIKI
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
If you cant flash SPL 2.40 you will need to flash back to a ROM compatible with SPL 1.20
Read here: http://forum.xda-developers.com/showthread.php?t=392133
I'd try to grab one of thoise older Roms and flash using SD card method.
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
And dont forget to install carrier cab.
I can't seem to connect my xv6800 to the computer so I can run that program.
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
loc37 said:
I plug it in and the sound comes up and I run the program but it says that it can't copy to device.
Click to expand...
Click to collapse
Then you need to get a Rom and radio compatible with SPL 1.20.. You'll need a SD card thats Equal to or less than 2GB (NON SDHC)
Check the compatibility here: http://forum.xda-developers.com/showthread.php?t=392133
Read the instructions for flashing this here:
http://wiki.xda-developers.com/index.php?pagename=TITAN_GettingStarted
Check the Flashing with a SD card section.
Process is the same for the radio and the rom.
I cant seem to find an available rom that you need though.. I'll post back when i do.
Unless someone else has a trick for you...
You can also try a another machine that may recognize your phone.
What did you actually try to flash your phone with, and how did you do it.. this is important to help you.
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
loc37 said:
okay so what I did was cook up a ROM and then added the Radio 3.37 from alltel on it. I restated the phone and waited the windows mobile 6.1 load screen did not change I moved my keyboard and the sound functioned. I did a restart a hard reset everything I believe it is something with the rom. Any suggestions?
Thanks
Click to expand...
Click to collapse
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
im1badazchick said:
Hello loc...try here>>>>http://www.jrstreet.com/flash/burgertime.htm it's a tutorial made by burgertime from howard forums in the cricket section and it's a vid so you can just got through the steps if you get confused..i'm with cricket as well...try here for mms settings that will get your pic/vid messaging working if you have the software installed>>> http://forum.ppcgeeks.com/showthread.php?t=25859 and here is a rom for cricket if you dont wanna try and cook your own just yet>>> http://forum.ppcgeeks.com/showthread.php?t=18836 i love the new dcd 326 which is what i use but in order for me to get my pic/vid messaging working i had to include an oem version of arcsoft when i cooked my rom and vetvito's rom includes everything that you would neeed so you only need to put in the correct seetings plus you need the correct bootloader(olipro 2.40 or nuespl 2.47) and a radio 3.35 or higher...thanks guys and i hope everyone enjoys the weekend and loc i hope that you get it working...by the way loc there is a cricket forum http://howardforums.com/forumdisplay.php?f=336 and a sub forum for pda's that are flashed to cricket
Click to expand...
Click to collapse
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
loc37 said:
Okay what i have done now is loaded my own personal ROM and then added 3.42.02 Radio to it. The only problem with that is that it keeps restarting and restarting its really weird. Is there any way that i can fix that?
Thank you
Click to expand...
Click to collapse
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
im1badazchick said:
do you have one of the correct bootloaders? because just flashing to a custom rom and adding a new radio doesn't give you the bootloader that you need so you have to have that too...you can check it by holding down the power button, the camera button and inserting your stylus into the soft reset hole at the bottom of the phone and to get back out of it just do a soft reset but it needs to be be either 2.40 or 2.47 not 1.20 or anything else
Click to expand...
Click to collapse
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
flyers2114 said:
......flash a stock pre-gps rom and then upgrade the bootloader to 2.47........then flash whatever you like....
Click to expand...
Click to collapse
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
Usually that means you have the wrong build of MSVC installed use build 19209...
loc37 said:
Okay I solved that problem but now when I click on the settings option on the menu my phone freezes. What can be the cause of that? Did I cook the ROM wrong?
Thanks
Click to expand...
Click to collapse
if you now have the correct bootloader and radio...try flashing with a pre-cooked rom like dcd 326 or the rom from the links that i gave you...the popular one was the black pill and there is one that's specifically for cricket
do I just google that build number or is there a specific program I should download?
Thanks
loc37 said:
do I just google that build number or is there a specific program I should download?
Thanks
Click to expand...
Click to collapse
LOL..no if you lookk about five post up you will see DCD 326 and as for the other from vetvito it was in one of the links that i first posted for you
loc37 said:
When I turn off my phone it says 1.20. What can i do to change it? What software should i Download?
Thank You very Much
Click to expand...
Click to collapse
Did you read any of my posts...
Hrm.. could have sworn I addressed this already.
x51 said:
You can get the SPL 2.40 here:
http://www.lifesnotsogood.com/dcd1182/titan/spl/
Click to expand...
Click to collapse
x51 said:
Then from within Windows Mobile (on your device) Upgrade bootloader to 2.47 (Available from the same link as 2.40 above)
Then flash the radio and rom version I have in my signature.
Click to expand...
Click to collapse
I included links, and all the information you would need.. (Like the Rom/Radio/SPL compatibility list) yet you didn't read it.
I spent time finding those links, downloading a rom.. cooking it for you, and uploading it to my webserver so you can download it.
x51 said:
Download DCD 1.6.10 and flash it to your device with the SD card method (Instructions and links in my previous Post) I couldnt find the rom, but I downloaded the kitchen and cooked a rom that should work for you.
Download it from my webserver here:
http://x51.nx-1.com/TITAN/Roms/
Remember you need a proper SD card for this.. if you don't have one, you'll need to buy one.
After flashing this rom.. Assuming your radio is compatible... You should boot into the OS (forget making calls or getting data connection) Just download SPL 2.47 and execute it on your device.. once the SPL is upgraded, Flash the newest Radio, flash the newest rom, run the carrier cab, install aplications..
Let me know if you run into trouble.
Click to expand...
Click to collapse
I also explained that once you boot into windows with that rom, you need to upgrade your bootloader to 2.47 (with instructions) and then your radio, and then rom.
The path was simple..
Flash dcd 1.6.10 (compatible with SPL 1.20) so the phone will boot
Upgrade SPL (bootloader to 2.47)
Flash new radio (3.47.50)
Flash new Rom (3.2.6)
Run carrier cab.
If you are still asking about where to get the (SPL) bootloader.. I guess I cant help you....