It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
I have not seen this... but my suggestion would be to do the Power + Camera + reset... and let it go into bootloader... then just reflash the rom.
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
Like the other guy said, force bootloader but take note of the version. Make sure you are running version 2.40 or greater. If you are running stock bootloader 1.06 or anything else it will have the reboot loop. Read the wiki in my signature fully before doing anything else. Did you read this before flashing?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5?????
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
paulash said:
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
This wiki tells you the steps.... I did it as follows... but... after doing the radio... you have to force it into the bootloader. It will not load into the phone rom.
xv6800 Rom Upgrade Instructions Wiki
gc14 said:
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
Click to expand...
Click to collapse
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
paulash said:
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
I put radio 3.42.30 on there but had to get HardSPL-2.40 on it first. The wiki explains it very well.
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
nitro66215 said:
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
Click to expand...
Click to collapse
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
scrawnyb said:
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
Click to expand...
Click to collapse
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
paulash said:
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
Click to expand...
Click to collapse
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
nitro66215 said:
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
Click to expand...
Click to collapse
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
paulash said:
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
Click to expand...
Click to collapse
It shouldn't be reverting back to 1.2. If you have 2.4 installed correctly... and you check with the "Reset"... then you can do the RUU update right from that bootloader screen. If it is 1.2... then attempt the 2.40 hard spl from that screen instead of redoing the stock rom.
nitro66215 said:
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
Click to expand...
Click to collapse
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
serfboreds said:
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
Click to expand...
Click to collapse
I don't agree that the USB / Activesync is 6 or 7 steps. I did 4 or 5 at the most.. and I'm counting the power+camera+reset as a step.
flash
When the bootloader screen comes up with 1.2, are you just assuming its done...or do you actually then keep clicking through the options until it actually flashes the phone with the ROM?
Related
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
I went from stock to 3.2.0 / Radio 3.42.02.. no problems.
I have not loaded 2.42.30 (I prefer to use the radio version released by HTC for this device.. 3.42.30 was released for another device and ported.. although it seems to work for everyone.)
I HAVE read that for radio 3.42.30 you need SPL 1.20 for USB Flashing.
gc14 said:
Yeah 1.20 is needed to flash these radios via USB. Just need to put 2.40 back when you're done.
Click to expand...
Click to collapse
Based on that.. I assume SD flashing is ok with 2.40.
scotcha12345 said:
... (maybe thinking the Radio needed to be installed for it to get through)....
Click to expand...
Click to collapse
Yes! This is well documented.. a common issue.
If you flash the Rom without a compatible radio.. you will get stuck on the verizon screen... I suggest flashing the ROM AFTER the radio.. since you flashed the Rom already... when you get the radio working, Reflash the ROM.
Did you flash the radio via SD Card or USB?
Did it show a progress bar while flashing?
Let us know how your attempting to flash the Radio (USB or SD) With specific steps (held buttons X, Y, and Z.. saw this message, pressed this key.. saw this on the screen) .. and someone will let you know what you might be doing wrong.
Also.. dont forget to run the carrier cab when your done.. This is worth mentioning since it's the most common issue once the device boots and you cant program the phone, or make data / voice connections.
scotcha12345 said:
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
Click to expand...
Click to collapse
Can you get to the bootloader by holding down camera power and pushing the reset button? If so, you can flash the radio with the SD method found in the wiki. just put the radio on the sd card in the proper format and enter bootloader and it should correct your problem.
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Responses
Hey guys,
Thanks for the responses and suggestions.
1) At the moment he doesn't have an SD card aside from the SDHC, so he couldn't do that until he purchases one. Good idea though if nothing else works
2) When pressing the camera/power/reset he's in the SPL 2.4 bootloader screen, he's going to try your suggestion of downloading Sprints and upgrading.
3) I'll ask him procedurally what else he has tried, what error he gets for recording. No doubt you were correct about uploading the Radio before the ROM
I've actually flashed my phone exactly the same way he has so that I can try to experience the same problems, and try to figure it out myself.
Bingo
Hey,
The Sprint ROM .exe was the answer. Very smart, thanks again for helping us both out. Was getting a little nervous for about 2 minutes.
useful=helper++
I did the same thing. Thank you very much...saved my butt!
BC
its alive
spreeway said:
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Click to expand...
Click to collapse
you saved my titan...thanks guy!
I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
Click to expand...
Click to collapse
I'm not sure what you mean about fear of relocking and relocking breaking the usb port.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
http://forum.ppcgeeks.com/showthread.php?t=21953
Read first post
This is only a small example but I'm sure I could find more than 10 instances of this throughout threads. Including NO2Chem saying not to do it aswell.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
Click to expand...
Click to collapse
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Read the first post in the link I gave you. Then you can do a search on downgrading issues to find more reports.
I know it can be done because I've done it on 2 different Titans now. I made the thread to help prove that it can be done so other arent so scared by the rumors as you call it.
gc14 said:
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
Exactly... I'm attempting to put the rumor to rest. Atleast as far as Verizon customers are concerned.
What SPL are you using before relocking to 1.06?
yep
Rom 2.09
Radio 1.30
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
lllboredlll said:
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I am not sure if you answered his question. Which bootloader are you running, nueSPL or other?
I have heard some concern with reverting to non-GPS stock using the no2chem tools, but obviously there is no worry with the relocker and such.
gc14 said:
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
Click to expand...
Click to collapse
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
It gets hard to think straight with people flying in and out of my office every 5 seconds. I'll try to read a little more throughly next time.
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
Click to expand...
Click to collapse
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Now all there is left to do is link this to ppcgeeks and be done with the rumor. Thank you for your input....
gc14 said:
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Click to expand...
Click to collapse
I vote to have this added to the return to stock wiki. GC will you post?
How about USCC?
Brings me back to my previous question, GC (Previous Thread); How can I back-up the current ("Stock" for USCC) OS ROM and RADIO on my new Titan? It was discussed that it [dumping current ROM and Radio and then using dump to re-flash] couldn't be done. I wanted to do a ROM dump before flashing to DCD's so that I could revert to it if needed; also, so that I could re-flash to "stock" on my old unit before sending it back to USCC... however, I don't how to accomplish this, if at all possible to do so!
If anyone can guide me through this, I could upload the USCC "Stock" (for lack of a better word, since USCC has no actual "Stock" Roms) ROM and RADIO and make it available to other unfortunate USCC customers. I agree w/Serfboreds, and also vote to have this thread added to the "Return to Stock" Wiki.
Thanks, Guys!!
gc14 said:
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
I think the issue lies with Sprint customers..... I personally have reflashed to stock at least 15-20 times.... from a GPS ROM and back.....
That is a very nice summary of steps for re-locking from various spl's and definately needs to be entered into the !iki.... If GC doesn't have time I'll do it when I get done here at the dentist.... booooooo....
I think the real issue was going from bootloader nueSPL 2.47 to a stock GPS rom caused problems. But because verizon customers dont have a stock gps rom to flash back to we go to a non-gps (1.XX) radio which does not cause the problem.
No2chem originally made the advice not to go back to a stock assuming stock included 2.XX or 3.XX radios. Once he was alerted to the fact that going back to stock 1.XX (i.e with verizon) did not cause a problem he modified his warning advice.
Once again, the warning is only valid for bootloader nueSPL 2.47
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
Click to expand...
Click to collapse
Yes, it negates the problems.
gc14 said:
Yes, it negates the problems.
Click to expand...
Click to collapse
Thanks dude. And I agree with Serfboreds that you should add this advice to your wiki. Very easy to understand and maps out all (most) of the possible relock escape routes.
Once again gc you are a font of wisdom.
ugh.... i can't keep up with all the misinformation anymore. If it works for you verizon users in your personal experience though good for you. I know for a fact it can cause problems. I'm starting to narrow it down to the original 3.35 leaked rom with GPS radio from sprint, but have no firm proof it's that narrow scope yet . Still have myself a brick from the GPS to pre-gps and I didn't use nueSPL Relocker thats for sure =P
For more info on the problem and others that experienced this "rumor" first hand go to ppcgeeks and search for "download mode"
i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?
thanks
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
belmont said:
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
Click to expand...
Click to collapse
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
scrosler said:
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
Click to expand...
Click to collapse
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
belmont said:
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
Click to expand...
Click to collapse
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
scrosler said:
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
Click to expand...
Click to collapse
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
belmont said:
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
Click to expand...
Click to collapse
Hmmm, maybe try a different USB port at this time. Also, try this...
Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.
In XP I beleive it will show up under USB at the very bottom of Device Manager.
Does the phone show up at all?
Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....
You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....
..................................
Ok so I just got my new device and I tried to update the bootloader from 1.04 to 2.47 with the new SPL with the .exe file form here. It restarted to flash and it froze. What do I do? I can't boot it to the OS and I can't update the bootloader. Please Hlep ASAP. I am stuck with SPL-104 and windows 6
Thanks.
if you can't get out of bootloader you may have to flash a stock non gps rom.
I am jsut flashing the bootloader. It had the original stock ROM on it.
lafester said:
if you can't get out of bootloader you may have to flash a stock non gps rom.
Click to expand...
Click to collapse
lafe is right.....flash a stock non-gps rom.......when you tried flashing the Nuespl 2.47 you did do it via SD card correct?
yes I did. I flashed it on a Non GPS stock VZW ROM
JukEboXAuDiO said:
yes I did. I flashed it on a Non GPS stock VZW ROM
Click to expand...
Click to collapse
try flashing another stock non gps rom and then try to upgrade the BL again....this time try Olipro 2.4.....somehow the BL didnt flash correctly the only way out is to flash the stock non-gps rom and the proceed...
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
JukEboXAuDiO said:
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
Click to expand...
Click to collapse
No....but above you posted 2.47.....you could try Nuespl 2.47 it is the latest and greatest...go over to PPCgeeks and grab it off my sig over there....it runs fom the SDcard....also what have you tried to get it back?.....if you have not already try a hard reset first.....
Here I will save you some time
http://forum.ppcgeeks.com/showthread.php?t=30561&highlight=hardspl+2.47
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
JukEboXAuDiO said:
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
Click to expand...
Click to collapse
Can you enter BL?
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
JukEboXAuDiO said:
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
Click to expand...
Click to collapse
ok let me make sure I understand.....you are in BL? which are trying to Un-lock with Olipro 2.4 or nuespl 2.47?
I am truing to unlock Olipro 2.4
I am a little confused also. Its been awhile since I flashed olipro 2.4... Aren't you supposed to pull usb at some point during the install?
you have to follow ALL of the instructions for the flash to work.
Nuespl 2.47 is much easier to use. I would still recommend reflashing the stock rom so you can put nuespl on your sd (providing it is 2gb or less).
if you are in bootloader you can just run the ruu and it will flash.
JukEboXAuDiO said:
I am truing to unlock Olipro 2.4
Click to expand...
Click to collapse
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
flyers2114 said:
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
Click to expand...
Click to collapse
Its stuck on the loading screen.
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
JukEboXAuDiO said:
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
Click to expand...
Click to collapse
1.04 is verizon's stock bootloader. Do these steps with an SD card. You can try using Verizon's stock OS/Radio... but it never works for me the first time.
1) Download the Sprint latest Rom Update. Right click the EXE file and extract the files.
2) Copy and rename Ruu_signed.nbh to TITAIMG.nbh on the storage card.
3) Put the card into the phone...Power+Camera+Reset. This will get into bootloader, and load the image.
When complete.... soft-reset.
DO NOT LET CUSTOMIZATIONS RUN!!!
When you get to the WM 6.1 screen and it asks for you to touch screen... DO NOTHING!!!
Remove SD card.
Connect your USB cable... get activesync to see it... Just tell it to cancel the syncronization.... Then run Olipro's Titan Unlocker 2.4.
When it's done getting 2.4 on it.... Copy the radio rom you want IE 3.42.50 to the SD card and flash away. Then the same for the new OS.
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
JukEboXAuDiO said:
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
Click to expand...
Click to collapse
No problem. It does get tricky, but once you get the hang of the concepts.... flashing back and forth is easy.
Anyone encountered this error before? It gets to 8% and then phone reboots and I get this on my PC screen. It says Error [328] (see attached image)
I am using Radio 3.37.75 (verizon), and my bootloader shows 2.40 Olipro
Any ideas?
Try this RUU it is version 3.16.4.3.
Yes, thats the version that I am using. I think... when I run it, it says 3.16.4.3 in the window title bar. (see screen shot)
EDIT: I tried it anyways, and I got the same thing. Do I have the right bootloader? Would a different one help?
what are you trying to flash
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
wildcard said:
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
Click to expand...
Click to collapse
Just follow my post here and only use the files and Radios that I provide. Make sure you read a few times so you understand, and dont skip anything. Most important based on what I have read in this thread. Use only the radios I provide on my share site and take your time paying close attention.
http://forum.xda-developers.com/showpost.php?p=3687027&postcount=144
Thanks, I'll do it exactly like that. I will keep you posted. I have to get a new micro SD card, I only have an SDHC 8 GB
The radio can be updated via usb. I do it all the time. But it does hard reset the phone in the process.
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
I followed the directions exactly like in Ryan's post mentioned above, (used USB instead of SD card), and it works!
Fully functional. I used Radio 3.42.02 (somewhere I saw that it was recommended over the others, went with it to be safe). Then Flashed Ryan Mogul Rom 2.2 Heavy.
Thanks everyone!
drewcam888 said:
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
Click to expand...
Click to collapse
i have spl olipro-2.40, rom dcd 3.2.6 and want to upgrade radio to 3.42.50 using usb. should i downgrade spl to 1.20 before upgrade the radio? or i stick with current config and update the radio using RUU?
Still cant load radio
Obtained 6800 originally Alltel, not sure which radio, Had Olipro 2.40 installed, would hang on Alltel splash screen.
Could not get any RUU loads to complete (from USB or SD card), usually would fail around 50%.
Eventually was able to get RyanMogul 3.1 Cricket (lite) to load, but shows no radio and eventually screen goes blank. Never goes into active Sync mode.
We force boot loader mode and try and load several radios including Titan_Radio_ROM_3.42.50.Alltel.rar, Titan_Radio_ROM_3.35.04,
but keep Getting error 328 from RUU when I try to load a radio..
tried RyanMoguls "Here is a fix for GPS for all you VX6800 users that gps will not function!!", but cant run relocker because no active sync connection.
Stock Verizon ROM RUU also gets error 328.
Any ideas.