Anyone encountered this error before? It gets to 8% and then phone reboots and I get this on my PC screen. It says Error [328] (see attached image)
I am using Radio 3.37.75 (verizon), and my bootloader shows 2.40 Olipro
Any ideas?
Try this RUU it is version 3.16.4.3.
Yes, thats the version that I am using. I think... when I run it, it says 3.16.4.3 in the window title bar. (see screen shot)
EDIT: I tried it anyways, and I got the same thing. Do I have the right bootloader? Would a different one help?
what are you trying to flash
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
wildcard said:
trying to flash my verizon xv6800 (which has an old dcd rom on it, radio 3.27 i think) to the new radio: 3.37.75.
Then i will flash with a newer dcd or ryan mogul rom.
Click to expand...
Click to collapse
Just follow my post here and only use the files and Radios that I provide. Make sure you read a few times so you understand, and dont skip anything. Most important based on what I have read in this thread. Use only the radios I provide on my share site and take your time paying close attention.
http://forum.xda-developers.com/showpost.php?p=3687027&postcount=144
Thanks, I'll do it exactly like that. I will keep you posted. I have to get a new micro SD card, I only have an SDHC 8 GB
The radio can be updated via usb. I do it all the time. But it does hard reset the phone in the process.
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
I followed the directions exactly like in Ryan's post mentioned above, (used USB instead of SD card), and it works!
Fully functional. I used Radio 3.42.02 (somewhere I saw that it was recommended over the others, went with it to be safe). Then Flashed Ryan Mogul Rom 2.2 Heavy.
Thanks everyone!
drewcam888 said:
I would try a newer radio like 3.42.40. http://wiki.xda-developers.com/index.php?pagename=TitanRadioROMs
I got my radio from there and have no problems updating the radio with ruu.
Click to expand...
Click to collapse
i have spl olipro-2.40, rom dcd 3.2.6 and want to upgrade radio to 3.42.50 using usb. should i downgrade spl to 1.20 before upgrade the radio? or i stick with current config and update the radio using RUU?
Still cant load radio
Obtained 6800 originally Alltel, not sure which radio, Had Olipro 2.40 installed, would hang on Alltel splash screen.
Could not get any RUU loads to complete (from USB or SD card), usually would fail around 50%.
Eventually was able to get RyanMogul 3.1 Cricket (lite) to load, but shows no radio and eventually screen goes blank. Never goes into active Sync mode.
We force boot loader mode and try and load several radios including Titan_Radio_ROM_3.42.50.Alltel.rar, Titan_Radio_ROM_3.35.04,
but keep Getting error 328 from RUU when I try to load a radio..
tried RyanMoguls "Here is a fix for GPS for all you VX6800 users that gps will not function!!", but cant run relocker because no active sync connection.
Stock Verizon ROM RUU also gets error 328.
Any ideas.
Related
I have done the upgrade and everything went fine. After the upgrade it ran to extended rom configs and they went fine. My phone is no longer showing that it is connecting to 3G. All I have is the E logo on top. I am in my office and it is a 3g area, I was connecting 3G before the upgrade.
I have reinstalled the PTT .cab, and Hard Reset after it etc... Still the same.
I was going to upgrade my radio from 1.33 to 1.34 this morning, but when I ran that installer it told me that it was the wrong country??? Should I keep my radio 1.33? anyone know whats going on with this?
Thanks.
Gromet said:
I have done the upgrade and everything went fine. After the upgrade it ran to extended rom configs and they went fine. My phone is no longer showing that it is connecting to 3G. All I have is the E logo on top. I am in my office and it is a 3g area, I was connecting 3G before the upgrade.
I have reinstalled the PTT .cab, and Hard Reset after it etc... Still the same.
I was going to upgrade my radio from 1.33 to 1.34 this morning, but when I ran that installer it told me that it was the wrong country??? Should I keep my radio 1.33? anyone know whats going on with this?
Thanks.
Click to expand...
Click to collapse
Maybe try putting SPL 1.09 on it then running the RUU Shipped Radio ROM 1.27 from Germany.
OK< I tried what you said. My phone is SPL 1.09. So I ran the 1.27 RUU. I got the same kind of error.
ERROR 120: COUNTRY ID ERROR
The ROM image that you are trying to use is not designed to work with your device. Please check the vendor website and download the correct ROM update.
??????????????????????????????????????????????????????????????????????
Before loading another radio on it. just make sure it's the icon that is just not showing the correct connection, as some radios do... Check mspeed from your phone's browser for your actual connection speed... http://www.dslreports.com/mspeed
Gromet said:
OK< I tried what you said. My phone is SPL 1.09. So I ran the 1.27 RUU. I got the same kind of error.
ERROR 120: COUNTRY ID ERROR
The ROM image that you are trying to use is not designed to work with your device. Please check the vendor website and download the correct ROM update.
??????????????????????????????????????????????????????????????????????
Click to expand...
Click to collapse
Sounds like you are not SUPERCID. Run Pof v3 Unlocker, verify supercid, then try again.
Bimboy said:
Before loading another radio on it. just make sure it's the icon that is just not showing the correct connection, as some radios do... Check mspeed from your phone's browser for your actual connection speed... http://www.dslreports.com/mspeed
Click to expand...
Click to collapse
Good point. MT_PC_Hermes_PTT_REG_070129.CAB fixes the icon settings in the new Cing ROM.
Just ran a speed test... 207kbit/sec...
You might also just go to the \extended_rom via totalcommander or other filemanager and execute autorun.exe or at least the cab that corrects the 3g/u/e icons MT_PC_Hermes_PTT_REG_070129.CAB
A lot of people have found that for some reason after upgrading via mfg package to the 2.06 cingular rom, that the entire entended_rom did not run; even if they did not stop it after the upgrade. It looked like it loaded to most people, but they did not have the useless icons like telenav, mobiTV, etc..
OK, so something strange happened... I went to run POF's unlocker again. I ran it, but all of a sudden a ROM image begins to load? It looked like it was reloading the cingular image I loaded yesterday. Just than I get called into a meeting, when I get back, my phone is sitting there, looking the same as I left it before doing anything EXCEPT I have a G Icon now. Great, so I just checked the settings...
ROM Version 2.06.502.3
RADIO Version 1.16.00.00 ?????????????????????
Should I keep this radio or uupgrade it to a newer one, and if you think a newoer one than which should I try?
Gromet
Gromet said:
OK, so something strange happened... I went to run POF's unlocker again. I ran it, but all of a sudden a ROM image begins to load? It looked like it was reloading the cingular image I loaded yesterday. Just than I get called into a meeting, when I get back, my phone is sitting there, looking the same as I left it before doing anything EXCEPT I have a G Icon now. Great, so I just checked the settings...
ROM Version 2.06.502.3
RADIO Version 1.16.00.00 ?????????????????????
Should I keep this radio or uupgrade it to a newer one, and if you think a newoer one than which should I try?
Gromet
Click to expand...
Click to collapse
I think the consensus is that 1.27 is best until/if GPS ever works.
WAIT!, Lat time I checked your sig, did you not have Radio 1.34? Now I see you are on 1.27. Did you downgrade for a reason? I started the 1.34 upgrade just before you posted. What are the differences between 1.27 and 1.34?
Gromet
More strangeness...
So I started the 1.34 radio upgrade, click update, phone reloads into blotloader, goes to upgrading radio stack please wait... PC shows Stage 1: Upgrading Radio, BUT it just sits there at 0% than errors out.
SO
I ran the 1.27 Upgrade, SAME THING>???????????????????
Whats goin on?
BTW, I'm on SPL 1.09 and I ran Pof's Unlocker again successfully....
Gromet said:
More strangeness...
So I started the 1.34 radio upgrade, click update, phone reloads into blotloader, goes to upgrading radio stack please wait... PC shows Stage 1: Upgrading Radio, BUT it just sits there at 0% than errors out.
SO
I ran the 1.27 Upgrade, SAME THING>???????????????????
Whats goin on?
BTW, I'm on SPL 1.09 and I ran Pof's Unlocker again successfully....
Click to expand...
Click to collapse
What is you Radio BL 107 or 108?
I had access to two separate 8525's. One had 1.34 and the other had 1.27 (BL0107). The 8525 I keep and use daily is on 1.27 with BL 0107. I am waiting for further NBH flashing directions before changing both devices to BL 0108.
When it goes into Botloader mode, it sais SPL 1.09, Where else do I find the bootloader version?
Gromet said:
When it goes into Botloader mode, it sais SPL 1.09, Where else do I find the bootloader version?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=289173&highlight=hermes+rversion
mtty
To access the radio bootloader for that, but the command to do this (rtask a) has been removed in SPL-1.09.
If you downgrade the SPL to 1.04, you can see it using radio bootloader command "rversion":
Code:
USB>rtask a
Enter Radio Bootloader
rversion
Gromet said:
OK, so something strange happened... I went to run POF's unlocker again. I ran it, but all of a sudden a ROM image begins to load? It looked like it was reloading the cingular image I loaded yesterday. Just than I get called into a meeting, when I get back, my phone is sitting there, looking the same as I left it before doing anything EXCEPT I have a G Icon now. Great, so I just checked the settings...
ROM Version 2.06.502.3
RADIO Version 1.16.00.00 ?????????????????????
Gromet
Click to expand...
Click to collapse
Gromet, this is normal behavour. Pofs unlocker flashes a hacked radio rom (1.16.00.00). Once device restarts, you need to copy the unlocker exe file (included in pof's unlocker zip) to your device, and then execute it on the device. I guess the exe that you run on the device interacts with the hacked radio to unlock the device somehow.
Once thats done, you'll get a 'success' message. Now you can download the shipped rom 1.27.00.00. Since your device is now superCID you can just exec the exe in the shipped rom directly to upgrade the radio from 1.16 to 1.27
Just make sure that you kill activesync before playing about with any rom flashing - it gets in the way.
Nigel
So yeah....
I did everything for PoF's Unlocker, and I GOT the SUCCESS message... but now I cant get any version of a radio upgrade to run. If activesync is on, It starts the upgrade and never gets past 0%, if activesync is off, i error out even before it ever starts the upgrade.
Gromet
Gromet said:
So yeah....
I did everything for PoF's Unlocker, and I GOT the SUCCESS message... but now I cant get any version of a radio upgrade to run. If activesync is on, It starts the upgrade and never gets past 0%, if activesync is off, i error out even before it ever starts the upgrade.
Gromet
Click to expand...
Click to collapse
I don't have much to add other than, 'me too'--but eventually the upgrade worked. I Ran POF's unlocker and chose supercid as well. But couldn't get past that 0% with the 1.27.00.00 radio upgrade.
I'm at:
IPL - 1.00
SPL - 1.04
While typing up this message I decided to try again and type up the error verbosely.
Sure enough the sixth try was the charm.
-g
Gromet said:
WAIT!, Lat time I checked your sig, did you not have Radio 1.34? Now I see you are on 1.27. Did you downgrade for a reason? I started the 1.34 upgrade just before you posted. What are the differences between 1.27 and 1.34?
Gromet
Click to expand...
Click to collapse
I am back to 1.34 and I created the NBH standalone Radio ROM since the new tools are available now.
You can easily go between Radio ROM again YEAH!
Here are Radio ROMs:
1.27 http://uploadingit.com/files/8194/NBH Radio Only 1.27.00.00.zip
1.33 http://uploadingit.com/files/8194/NBH Radio Only 1.33.31.00.zip
1.34 http://uploadingit.com/files/8194/NBH Radio Only 1.34.00.10.zip
wpbear said:
I am back to 1.34 and I created the NBH standalone Radio ROM since the new tools are available now.
You can easily go between Radio ROM again YEAH!
Here are Radio ROMs:
1.27 http://uploadingit.com/files/8194/NBH Radio Only 1.27.00.00.zip
1.33 http://uploadingit.com/files/8194/NBH Radio Only 1.33.31.00.zip
1.34 http://uploadingit.com/files/8194/NBH Radio Only 1.34.00.10.zip
Click to expand...
Click to collapse
So, excuse my ignorance, but are we now saying that we can upgrade the radio roms listed without ending up with the 1.08 bootloader, or alternatively that 1.08 no longer causes a problem?
Rob
edit: as a result of a few people possibly bricking their devices, i have removed the standalone radio update.
at this time the best method of obtaining radio 3.35.04 is to flash the entire sprint 3.35 rom update.
Whoa. What are changes?
will this work on a Verizon one? or is it just Sprint?
DCD,
Getting an error on installation. RUU hangs at 9% then gives me Error[328] INvalid command, The update utility cannot be used for your PDA phone. Please check your update utility. I am running Olipro-2.40. Vz user. No issues in the past with upgrading rom or radio. Have been running leaked radio and both yours and No2Chem's roms.
Thoughts
okay so im seeing all kinds of misc threads around about this radio but everything is specific to Sprint...
no one can verify if this works with Verizon?
Anyone even know what the difference in the radio is from 3.27?
please excuse my ignorance, but I just want to make sure that if I'm already running one of your roms (2.3.1) that all I need to do is flash this radio. Is that right, or do I need to reflash the rom as well?
I am also getting the error at 9%. I have tried flashing about 5 times all with the same result.
Downloading the RADIO now... I've got DCD's 2.3.2 (modified a bit) ROM... will report once I get the Radio installed.... I am very excited.
weird, i had dcd 1.7.1 / radio 1.59.10a / spl-1.20-olipro
flash went fine
if you guys keep getting errors ill investigate further
vossco32 said:
I am also getting the error at 9%. I have tried flashing about 5 times all with the same result.
Click to expand...
Click to collapse
So you're just doing the radio and not the main ROM, correct? And are you just launching the updater or manually putting the phone into bootloader mode first?
I have your 2.3.2 release, 3.16 radio, and SPL-2.40.0lipro and I am getting the error. I will try a few more times. I did notice that the led flashes red right after it fails and reboots.
I am doing just the radio, and I have tried it both ways with the phone in bootloader and without.
Yep. Also getting the error here... I'm using DCD 2.3.2 ROM.
Still no luck either, running No2Chem 5049, 3.16 radio and 2.40. Extracted your radio and it is no different on 3 different RUU's, the same for the radio straight from the Sprint release.
rajuabju said:
Yep. Also getting the error here... I'm using DCD 2.3.2 ROM.
Click to expand...
Click to collapse
Me three, on my VZW 6800 with latest DCD and test Radio ROM.
Is the first post saying that I can use the New rom (released today) with olipro 2.40?
Yes I am getting the error at 9% also. Bummer.
dcd1182 said:
weird, i had dcd 1.7.1 / radio 1.59.10a / spl-1.20-olipro
flash went fine
if you guys keep getting errors ill investigate further
Click to expand...
Click to collapse
I flashed from 1.7.0 / radio 1.40 / spl-1.20
did spl 2.40 -> radio -> dcd 2.3.2 rom
no problems... except data is throwing invalid username again.. which is typical after a radio change.. just need to call verizon again
Same on 9%
I am also getting the error at 9%
VZW user with Olipro 2.40 and DCD 2.3.2 ROM
Edit: I have tried from both bootloader and with phone completely booted up.
l33tlinuxh4x0r said:
Is the first post saying that I can use the New rom (released today) with olipro 2.40?
Click to expand...
Click to collapse
No. That's already discussed in the thread on the new ROM (and in the ppcgeeks.com thread on the same topic). Here, we're talking about success (or lack thereof) in flashing just the extracted radio so that it can be used with custom ROMs and/or with non-Sprint phones.
David
Ditto
Thanks dcd, but getting same error at 9%...running NexVisions Hybrid, 2.40 etc.
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
I went from stock to 3.2.0 / Radio 3.42.02.. no problems.
I have not loaded 2.42.30 (I prefer to use the radio version released by HTC for this device.. 3.42.30 was released for another device and ported.. although it seems to work for everyone.)
I HAVE read that for radio 3.42.30 you need SPL 1.20 for USB Flashing.
gc14 said:
Yeah 1.20 is needed to flash these radios via USB. Just need to put 2.40 back when you're done.
Click to expand...
Click to collapse
Based on that.. I assume SD flashing is ok with 2.40.
scotcha12345 said:
... (maybe thinking the Radio needed to be installed for it to get through)....
Click to expand...
Click to collapse
Yes! This is well documented.. a common issue.
If you flash the Rom without a compatible radio.. you will get stuck on the verizon screen... I suggest flashing the ROM AFTER the radio.. since you flashed the Rom already... when you get the radio working, Reflash the ROM.
Did you flash the radio via SD Card or USB?
Did it show a progress bar while flashing?
Let us know how your attempting to flash the Radio (USB or SD) With specific steps (held buttons X, Y, and Z.. saw this message, pressed this key.. saw this on the screen) .. and someone will let you know what you might be doing wrong.
Also.. dont forget to run the carrier cab when your done.. This is worth mentioning since it's the most common issue once the device boots and you cant program the phone, or make data / voice connections.
scotcha12345 said:
Hey all,
Been trying just about everything to help a buddy out, but I've been failing repeatedly.
He got a brand new phone yesterday and found the XDA Titan Wiki to install the GPS enabled ROMs. He loaded SPL 2.4, then installed DCD 3.2.0. It got stuck at the Verizon screen when it restarted...then he apparently downloaded the Radio 3.42.30 to try and install that to get out of it (maybe thinking the Radio needed to be installed for it to get through). Now he's stuck at the White Verizon screen, and it says "No Radio".
Sounds like from when I read the Wiki he was supposed to install an intermediary Rom before jumping all the way to 3.2.0.
I've suggested using the Olipro SPL 1.2 unlocker, the Titan Relocker, several different ROM's and am at a loss as to how to fix it. He's still stuck at the Verizon screen displaying "No Radio."
Any suggestions?
Thanks
Click to expand...
Click to collapse
Can you get to the bootloader by holding down camera power and pushing the reset button? If so, you can flash the radio with the SD method found in the wiki. just put the radio on the sd card in the proper format and enter bootloader and it should correct your problem.
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Responses
Hey guys,
Thanks for the responses and suggestions.
1) At the moment he doesn't have an SD card aside from the SDHC, so he couldn't do that until he purchases one. Good idea though if nothing else works
2) When pressing the camera/power/reset he's in the SPL 2.4 bootloader screen, he's going to try your suggestion of downloading Sprints and upgrading.
3) I'll ask him procedurally what else he has tried, what error he gets for recording. No doubt you were correct about uploading the Radio before the ROM
I've actually flashed my phone exactly the same way he has so that I can try to experience the same problems, and try to figure it out myself.
Bingo
Hey,
The Sprint ROM .exe was the answer. Very smart, thanks again for helping us both out. Was getting a little nervous for about 2 minutes.
useful=helper++
I did the same thing. Thank you very much...saved my butt!
BC
its alive
spreeway said:
Can I suggest something to try? (assuming you have 6800)
1. Get the sprint release. http://forum.xda-developers.com/showthread.php?t=402887
2. in bootloader, load the sprint release by usb method. when it gets to having you touch the screen, soft reset.
3. In bootloader, load the dcd 3.2.0 rom (or any other rom).
4. Hard reset.
This should give you 3.2.0 rom and 3.42.02 radio.
Click to expand...
Click to collapse
you saved my titan...thanks guy!
Hello guys, I have a little bit of a problem, and I am hoping that you guys can help me out. About 10 months ago I upgraded from my stock ROM to dcd's 2.3.2. rom and 3.27.00 radio. Every thing went fine, loaded up 2.40 olipro and the installation went perfect. Now last month I saw that dcd came out with 3.2.6 and wanted to upgrade my rom and radio, but this is were i'm running into problems. I was able to flash the 3.2.6. rom, but I am unable to flash the radio. I have searched up and down these forums and checked out the wiki's and havn't been able to find a solution. So now all i'm left with is a phone that can't make a phone call but is still able to send sms messages. If anyone has any helpful tips or even a solution to my problem it would be much appricated.
I thought the 3.27 radio works with 3.2.6. What is happening when you try to flash the radio? and what method are you using to flash it (SD card or pc)? Also when you bootup the phone does it say 3.27 radio still? I believe all the newer DCD roms need a carrier cab have you installed the cab? I'm pretty sure the phone won't be able to make calls without the cab installed. 1 more Q what service do you have?
shield001 said:
I thought the 3.27 radio works with 3.2.6. What is happening when you try to flash the radio? and what method are you using to flash it (SD card or pc)? Also when you bootup the phone does it say 3.27 radio still? I believe all the newer DCD roms need a carrier cab have you installed the cab? I'm pretty sure the phone won't be able to make calls without the cab installed. 1 more Q what service do you have?
Click to expand...
Click to collapse
When I flash the radio it goes to 8% flashes a red light and then resets. I have also tried both methods of flashing but none works. When I bootup the phone it does still say 3.27 as the radio. I have also tried to install a carrier cab but have had no luck.
Try updating to Hard SPL 2.47
The 3.27 Radio is NOT compatible with ANY DCD version 3.X and higher..... Have you read the Wiki? Can you flash the radio using the SD card method? All of your questions have answers in the Wiki.....
You should flash back to 2.3.2. Go into the bootloader(tri-color screen) and then flash 2.3.2 to the phone..... reboot it.... it should load up ok.... If this works for you to this point, you have several options to upgrade the radio ..... Read the Wiki....
azclown said:
The 3.27 Radio is NOT compatible with ANY DCD version 3.X and higher..... Have you read the Wiki? Can you flash the radio using the SD card method? All of your questions have answers in the Wiki.....
You should flash back to 2.3.2. Go into the bootloader(tri-color screen) and then flash 2.3.2 to the phone..... reboot it.... it should load up ok.... If this works for you to this point, you have several options to upgrade the radio ..... Read the Wiki....
Click to expand...
Click to collapse
I looked over the wiki again and was able to re-flash to 2.3.2. Thanks for your help guys.
Hi I'm looking for some help. I tried upgrading my XV6800 to the windows 6.5 rom but I think I might of messed up. I tried to update my radio first but ran in to issues.
I used Oilpro 1.20 to try and tried to update the radio but along the way messed up while trying an older rom and I'm currently at a Verizon screen with the message "NO RADIO" at the bottom. I'm assuming the radio rom was erased. I might have gotten confused with the roms and used a rom without the appopriate Radio. When I try to flash that rom back to a stock Verizon upgrade it just ends 11% in to the flashing process and the rom update utility returns a Error 290 screen.
Currently I can get the oilpro 1.20 bootloader to still load up but I'm not sure what to do at this point. I tried updating the ROM to DCD's older 3.20 roms, which did complete but I still have that screen coming up. Can anyone give me some suggestions on what I should do next? Any help would be greatly appreciated.
Try using NueSPL 2.47 it's more current
Doesn't have have to be run on the phone itself once inside Windows? The only screen I can get up is the Verizon (splash) screen where it normally lists the rom and radio, or the oilpro boot loader screen. I actually can't get back in to windows to run the nueSPL 2.40.exe file.
Is there a way for me to flash the radio back from a bootloader screen and USB or SD card? The thing is I actually tried to take the 3.42.40 radio and use the Flash Rom Utility to see if it would flash the radio rom back on but even though the process completes successfully, I still get the no radio error so I guess it doesn't work. Thanks for the help, I think I may have been a few of the idiots out there who screwed things up and didn't make sure the radio was up before attempting any rom upgrade.
You should've changed the bootloader first. Your radios that you are trying are not compatible with your bootloader.
Flash an old stock rom via SD, then update your bootloader to 2.47 once you can get back into windows, then update your radio, and then your rom.
Yeah that was one of the first things I've tried a USB update back to the stock Verizon 6.1 ROM, but for some reason it prematurely ends at 11% with the PDA Phone Update Utility throwing a ERROR 290 message. This is the first time this has happened as I've flashed with this same rom tons of times. I've been looking online for the past hour on how to flash the ROM from a SD card if I can't get in to Windows. But all I could find was the USB update utility and it ends at 11% Am I doing it wrong? any ideas would be greatly appreciated.
If you can still get in the bootloader then you should be fine....I would put it manually in bootloader holding power and camera simultaneously and poke the hole to get it into bootloader.
Once you do that plug in the data cable and run Olipro 2.40 or Nue 2.47. It should be able to take after that.
Basics steps to flashing a phone:
correct unlocker-->stock ROM-->custom ROM
Most custom ROMs will not include Radios that why you would run the stock ROM first to install the radio and then run the custom ROM. Alot simpler then trying to update the Radio by itself.
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Beyond888 said:
AWESOME! I got it back up, thanks guys. For reference purposes I'm going to restate the problem and solution incase other noobs run in to the same issue.
PROBLEM:
I installed oilpro 1.2 during the process of installing a new radio then a rom. Along the way the rom install failed. I tried to reinstall a stock Verizon rom RUU 3.57 & 3.37 radio but it failed at 11%. I was then stuck at the splash screen with a message that said NO RADIO. I could still get in to the boot loader with the power and camera button. But the stock Verizon rom did not install anymore.
SOLUTION:
I used titan_exitbl.exe to exit the bootloader and I went back to an earlier rom found here, rom 2.09 & radio 1.30. That one actually installed. It seems to have worked. I'm back in windows now but I need to uninstall oil pro 1.2 and get nuSPL 2.47 on there before I move further (it looks like while it's still on the stock RUU won't work for me).
Do you guys know how I would go about uninstalling Oilpro 1.2? Will Titan_relocker do it for me? I'm not sure if installing nueSPL over oilpro will do it.
Use this ROm from Verizon to get the Stock 6.1 back up and running. It's the MR2 rom
http://www.pcdphones.com/phone_downloads.aspx?bid=89&cid=1&mid=287&carrier=Verizon Wireless
Click to expand...
Click to collapse
Glad to hear you got your phone back up
As far as I know you should be able to just install 2.47 and it will overwrite your old bootloader without problems. I could be mistaken but there isn't really a way to "uninstall" a bootloader, just overwrite it with a different one.
unL33T is correct...just run Nue 2.47 and let it overwrite the old one. 8p
Yeah that's what I thought too, but when I tried to over right it with 2.47 the 1.20 showed up again so I used the titan_relocker tool. Maybe I did something wrong. I'll go recheck, thanks for the replies guys.