Ok so I just got my new device and I tried to update the bootloader from 1.04 to 2.47 with the new SPL with the .exe file form here. It restarted to flash and it froze. What do I do? I can't boot it to the OS and I can't update the bootloader. Please Hlep ASAP. I am stuck with SPL-104 and windows 6
Thanks.
if you can't get out of bootloader you may have to flash a stock non gps rom.
I am jsut flashing the bootloader. It had the original stock ROM on it.
lafester said:
if you can't get out of bootloader you may have to flash a stock non gps rom.
Click to expand...
Click to collapse
lafe is right.....flash a stock non-gps rom.......when you tried flashing the Nuespl 2.47 you did do it via SD card correct?
yes I did. I flashed it on a Non GPS stock VZW ROM
JukEboXAuDiO said:
yes I did. I flashed it on a Non GPS stock VZW ROM
Click to expand...
Click to collapse
try flashing another stock non gps rom and then try to upgrade the BL again....this time try Olipro 2.4.....somehow the BL didnt flash correctly the only way out is to flash the stock non-gps rom and the proceed...
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
JukEboXAuDiO said:
I am using OliPro 2.4 from the DCD ROM thread. Is that the wrong one? Its stuck ont he loading screen
Click to expand...
Click to collapse
No....but above you posted 2.47.....you could try Nuespl 2.47 it is the latest and greatest...go over to PPCgeeks and grab it off my sig over there....it runs fom the SDcard....also what have you tried to get it back?.....if you have not already try a hard reset first.....
Here I will save you some time
http://forum.ppcgeeks.com/showthread.php?t=30561&highlight=hardspl+2.47
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
JukEboXAuDiO said:
yes I have tried hard reset. It keeps going to hte bootloader. Ok i used Olipro 2.40 using hte cmd prompt and did what it told me to. When it restarted it got stuck on the updating page. Now its just stuck onthe loading page.
Click to expand...
Click to collapse
Can you enter BL?
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
JukEboXAuDiO said:
Yes. It loads to bootloader 1.04 and then goes to update from the SD Card and its stuck on the loading screen
Click to expand...
Click to collapse
ok let me make sure I understand.....you are in BL? which are trying to Un-lock with Olipro 2.4 or nuespl 2.47?
I am truing to unlock Olipro 2.4
I am a little confused also. Its been awhile since I flashed olipro 2.4... Aren't you supposed to pull usb at some point during the install?
you have to follow ALL of the instructions for the flash to work.
Nuespl 2.47 is much easier to use. I would still recommend reflashing the stock rom so you can put nuespl on your sd (providing it is 2gb or less).
if you are in bootloader you can just run the ruu and it will flash.
JukEboXAuDiO said:
I am truing to unlock Olipro 2.4
Click to expand...
Click to collapse
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
flyers2114 said:
and you are trying to un-lock with Olipro 2.4 via sd.....if that is so then that is the problem....
Click to expand...
Click to collapse
Its stuck on the loading screen.
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
JukEboXAuDiO said:
Can someone tell me where I can get the dman nbh file so I can re flash it back to what it should be so I can start over? All I have is a damn phone with no OS and bootloader 1.04.
Click to expand...
Click to collapse
1.04 is verizon's stock bootloader. Do these steps with an SD card. You can try using Verizon's stock OS/Radio... but it never works for me the first time.
1) Download the Sprint latest Rom Update. Right click the EXE file and extract the files.
2) Copy and rename Ruu_signed.nbh to TITAIMG.nbh on the storage card.
3) Put the card into the phone...Power+Camera+Reset. This will get into bootloader, and load the image.
When complete.... soft-reset.
DO NOT LET CUSTOMIZATIONS RUN!!!
When you get to the WM 6.1 screen and it asks for you to touch screen... DO NOTHING!!!
Remove SD card.
Connect your USB cable... get activesync to see it... Just tell it to cancel the syncronization.... Then run Olipro's Titan Unlocker 2.4.
When it's done getting 2.4 on it.... Copy the radio rom you want IE 3.42.50 to the SD card and flash away. Then the same for the new OS.
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
JukEboXAuDiO said:
Thank you so much dude. I am gonna get this thing moving today. Thanks again!
Click to expand...
Click to collapse
No problem. It does get tricky, but once you get the hang of the concepts.... flashing back and forth is easy.
Related
I cannot get any radio above 3.35.04 to take.
I have tried both RUU and the memory card way. Neither gets results. Why???
Running:
Xv6800-Verizon
Radio: 3.35.04
dcd_titan_3.2.0
dcd_titan_kitchen_3.2.0
RUU does work, but you have to downgrade your bootloader to 1.2.... SD flash should work fine, when you put the radio on the SD card, you do rename it to titaimg.nbh right? and when you goto bootloader what happens??
azclown said:
RUU does work, but you have to downgrade your bootloader to 1.2.... SD flash should work fine, when you put the radio on the SD card, you do rename it to titaimg.nbh right? and when you goto bootloader what happens??
Click to expand...
Click to collapse
I have the 2.40 bootloader, when do the bootloader, does to the raindow screen, flashes to a another sreen thats says loading..that only stays up for a half a second and thats it...doesnt ask me ? or anything
Install this bootloader:
http://forum.xda-developers.com/showthread.php?t=332381
flash radio (3.42.30?)
flash back bootloader 2.40
What size is your memory card? Make sure it partioned FAT32 with high allocation size.
NotLutzik said:
Install this bootloader:
http://forum.xda-developers.com/showthread.php?t=332381
flash radio (3.42.30?)
flash back bootloader 2.40
What size is your memory card? Make sure it partioned FAT32 with high allocation size.
Click to expand...
Click to collapse
I do this and the bootloader is still 2.40
highflyin128 said:
I do this and the bootloader is still 2.40
Click to expand...
Click to collapse
Did u used SPL 1.2 unlocker?
NotLutzik said:
Did u used SPL 1.2 unlocker?
Click to expand...
Click to collapse
I used the one in the link you posted
highflyin128 said:
I used the one in the link you posted
Click to expand...
Click to collapse
ok....guess it didnt get installed then.
Try again.
Connect your phone to Comp via activeSync
when it connected run unlocker
It will ask you to take usb out and out back in
and it should install 1.20 SPL
NotLutzik said:
ok....guess it didnt get installed then.
Try again.
Connect your phone to Comp via activeSync
when it connected run unlocker
It will ask you to take usb out and out back in
and it should install 1.20 SPL
Click to expand...
Click to collapse
Its wants to flash to the Titan-Hard SPL right?
highflyin128 said:
Its wants to flash to the Titan-Hard SPL right?
Click to expand...
Click to collapse
yea...it should say hard spl 1.20 something like that
I got it....When i was done going to 1.2 downgrade. i thought u had to booted into WM6,before continuing, so I was updated my rom which kept putting the 2.4 boot loader back in
THANKS GUYS
Good. After u done flshing radio dont forget to put boot loader 2.4 back
Hi there, I have very minimal experience with this stuff so I will provide as much detail as possible...
I had previously successfully programmed my HTC6800 back in March by unlocking with Olipro 2.4, then I flashed the radio with 3.27 and used dcd 2.3.2 for Bell on it. Now my memory is a little foggy as that was several months ago however I made it through the process fine. This encouraged my to try to update again today. I tried following the steps in the wiki as I could not find the guide I had used previously. I already had Olipro 2.4 so I was good at that step. I then tried running the newest radio update and it would not take. It gave me an error. I reset the phone and tried several times but to no avail. I then tried putting on dcd3.2.0 which went fine. THe phone rebooted and I made a test call and everything was fine. I however wanted the new radio update still so I thought I'd take another crack at it... it still would not update. In the wiki it said about relocking the phone and putting it back to the factory ROM and starting again. So I did this, I downloaded the relocking util and followed the instructions to relock the phone. That went fine... Olipro is gone and is shows the 1.06 like it's supposed too... next it said to put the factory ROM back on... well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
So currently my 6800 sits as the 3 colour screen with 1.06 relock on it and does nothing else. It has radio 3.27 on it and dcd 3.2.0.
Is there any way to fix this?????
Run this first to exit the bootloader and get into windows mobile. Then check out which rom you are on (I think you were on dcds rom). Then load radio via sd card method listed in the wiki. Then reload dcd if you are not already on the version that you want.
P.S. I have heard things about that ROM that it caused problems. You may want to read up on that here.
Nope
Well, I downloaded the file and tried running it but to no avail. It just comes up saying that the application failed to start because RAPI.DLL is missing.
Also
I tried running that app on a Vista machine as well and it just says that it can't open the USB port. However, windows found the device and installed a driver for it when plugged in AND it shows USB on the bootloader screen when plugged in.
ok..,. let me see...
try installing olipro 2.40 again, it seemes that your phone is locked (olipro 1.06) so it can't run the dcd custom rom... reset and see if you can enter windows...
then if you enter windows normally, downgrade to olipro 1.20 and install the new radio, then, once again upgrade to olipro 2.40 so it can enter windows...
let me know if it worked for you...
Evo69 said:
well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
Click to expand...
Click to collapse
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Here's the problem
OK. Here's the problem. I obviously misread the instructions on setting the unit back to stock as I just read them again and I realize my mistake. I did not load the stock ROM on first. I used the Re-lock program and re-locked my unit before putting the stock ROM back on. So I sitting at the 3 colour screen with SPL 1.06 and I have radio 3.27 on the unit and dcd's latest ROM on it. I can't get it past the 1.06 bootloader. I have tried a hard reset, I have tried the program above to exit the boot loader and it does not work. Is there any way I can get Olipro 2.4 back on or exit this bootloader???
just connect your phone to the computer (it's ok to be on the tri color screen) and install olipro 2.40 from the computer...
you just need to be sure that when you connect the phone in the tri color screen it says USB...
i'm attaching Olipro 2.40
No Dice
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
i had a similar problem yesterday when i tried to upgrade the radio form 3.42.02 to 3.42.30 and taht solved my problem...
so you basically cannot exit the bootloader mode?? even when you hard reset your device??
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Evo69 said:
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
Click to expand...
Click to collapse
I have the Bell ROM if you're looking for it.
TS
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
jhamilton said:
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
Click to expand...
Click to collapse
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
YES
Timeshell said:
I have the Bell ROM if you're looking for it.
TS
Click to expand...
Click to collapse
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Keystone said:
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Click to expand...
Click to collapse
I tried using a Sprint one... it would not work.
Timeshell said:
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
Click to expand...
Click to collapse
Yeah I've heard some horror stories when it came to downgrading, including a few bricked devices.
http://forum.ppcgeeks.com/showthread.php?t=26082
I would be interested to know if anyone on Bell has managed to successfully downgrade a 6800 to stock.
i thought dcd's new 3.2.0 needed a radio of 3.35 or higher to run and does not flash the radio when u flash his rom. Another problem with the phone not coming out of the bootloader is that you have to disable usb connections in active sync or windows mobile device center for the exit bootloader app to work. Try disabling the usb connection in whichever one applies for you and run the app again. If you can get out of the bootloader try to go back to ollipro 2.40 or use one of no2chems bootloaders as they work from the device and an sd card no need for a pc to flash the bootloader. once bootloader is unlocked again run a full radio/rom update like the sprint stock 3.35 easily found on htc's website under the titan (us version of the site). Don't let the carrier custimizations run ... the file that runs after u calibrate screen and set timezone just pull the battery. Then grab whatever rom / radio you want to or were trying to flash 2 before and name it put it on the root of an sd card (thats under 2gb and formatted to fat32) and rename the ruu_sighned.nbh file to TITAIMG.nbh hold power + camera and hit your soft reset button. The tri color screen will come up and should say loading then promt to hit the power button to flash and show u what u r flashing. cdma (radio). os (radio rom) or splash screen, or whatever you r trying to flash hit power button to start once done it will sit with update complete on the screen pull the battery out for about 30 sec and put it back in reboot and enjoy the custom rom or radio.
kdj67f said:
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Click to expand...
Click to collapse
You can use nueSPL 2.47 to load the locker/relocker but you need to be booted into WM6 to do so. You need to reload another rom that uses the bootloader you have currently loaded and then you can move forward or backward.
Evo69 said:
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Click to expand...
Click to collapse
Uploaded to Rapidshare
http://rapidshare.com/files/1271390...3.666.1_RS_1.37.30_BM_1.27_0604_SHIP.zip.html
TS
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
I have not seen this... but my suggestion would be to do the Power + Camera + reset... and let it go into bootloader... then just reflash the rom.
paulash said:
It reaches windows mobile, and the "tap screen to begin". It then restarts moments later. Why is it doing this????
Click to expand...
Click to collapse
Like the other guy said, force bootloader but take note of the version. Make sure you are running version 2.40 or greater. If you are running stock bootloader 1.06 or anything else it will have the reboot loop. Read the wiki in my signature fully before doing anything else. Did you read this before flashing?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5?????
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
paulash said:
QUICK question
I've put everything back to stock now.
can I install the radio AFTER I install DCD 3.2.5????? Because the radio 3.42.30 wouldnt boot on the stock rom, and I'd have to upgrade to 2.40 to reinstall wouldnt I?
Click to expand...
Click to collapse
This wiki tells you the steps.... I did it as follows... but... after doing the radio... you have to force it into the bootloader. It will not load into the phone rom.
xv6800 Rom Upgrade Instructions Wiki
gc14 said:
You need to be upgrading to 2.40 before you do ANYTHING, not just the radio. That was probably your problem before. From stock, bootloader, radio, rom in that order.
Click to expand...
Click to collapse
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
paulash said:
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
I put radio 3.42.30 on there but had to get HardSPL-2.40 on it first. The wiki explains it very well.
But doesn't 3.42.30 need SPL 1.20 to install correctly??? I don't think it'll let me install it on olipro 2.40.
Click to expand...
Click to collapse
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
nitro66215 said:
I didn't go through those steps GC. I did the olipro 2.40... then the 3.42.30... then had to force it into bootloader.... then did the DCD 3.2.3 update. That's it... and all done via USB cable.
Click to expand...
Click to collapse
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
gc14 said:
With the ridiculously cheap prices of 1gb microsd cards these days, you'd think you all would be flashing from the card and not the crappy usb.
Anyway, if you must flash everything with usb, this is what you need to do.
From stock:
- Olipro 2.40
- Official Sprint 3.56 Rom Update for Radio 3.42.02 (DON'T LET CUSTOMIZATIONS RUN!!!)
- 3.2.5
- Olipro 1.20
- Radio 3.42.30
- Olipro 2.40
See the hassle it is when you don't flash from the card?
Click to expand...
Click to collapse
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
scrawnyb said:
Damn GC, that's a lot of extra work compared to what I have people doing in my tutorial...
Click to expand...
Click to collapse
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
paulash said:
There's a REALLY annoying problem going on. I had to reflash to stock twice again. 2.40 installs successfully, and im in the boot loader. I open up the sprint 3.56 (and 3.42.02 radio) with the RUU, and it just reverts to SPL 1.20!!!! Why does this keep happening?
Click to expand...
Click to collapse
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
nitro66215 said:
It's because you aren't into the true HARD spl. You have the soft 2.40 spl. You have to verify that the bootloader is 2.40 by doing the power + camera + reset.
Click to expand...
Click to collapse
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
paulash said:
I have the hard SPL. I'll verify it again once stock rom reinstalls (I have to keep reinstalling to stock everytime it switches back to SPL 1.20... really frustrating).
Click to expand...
Click to collapse
It shouldn't be reverting back to 1.2. If you have 2.4 installed correctly... and you check with the "Reset"... then you can do the RUU update right from that bootloader screen. If it is 1.2... then attempt the 2.40 hard spl from that screen instead of redoing the stock rom.
nitro66215 said:
Why does everybody say you must have an SD card to do the upgrades? I never did anything with an SD card and was able to flash all the way to 3.2.5 without it.
Click to expand...
Click to collapse
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
serfboreds said:
Who said you HAVE to do this by SD? I think we are saying it is easier.
GC detailed that to flash by USB/Activesync is about six or seven steps and about an hour of work, versus flashing by SD which is less than five minutes and a step or two.
Click to expand...
Click to collapse
I don't agree that the USB / Activesync is 6 or 7 steps. I did 4 or 5 at the most.. and I'm counting the power+camera+reset as a step.
flash
When the bootloader screen comes up with 1.2, are you just assuming its done...or do you actually then keep clicking through the options until it actually flashes the phone with the ROM?
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
whiteblazer01 said:
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
Click to expand...
Click to collapse
Can you not put the phone in bootloader mode (power+camera+reset) and connect via USB? Even though activesync doesn't see it, it's still possible for RUU updater to connect. I had a similar problem before. Try doing this and putting Hard_SPL 2.4 on it.
Look at section II on this wiki... it says if you have 1.20 olipro... flash to an older rom and radio... WIKI
Snippit.... " if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
nitro66215 said:
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
Click to expand...
Click to collapse
Hes right, you need to load an old pre-GPS rom on your phone, then upgrade. I've had this happen myself.
Yes, this is what I saw too, however, all the roms I found on this page http://wiki.xda-developers.com/index.php?pagename=TitanOtherHome for the olipro 1.20 take me to an internal server error on fileshex.com. I can't find any rom file that I can actually download. Does anyone have a link to one or can you upload it? I suppose it doesn't matter which one it is, since I'm going to upgrade from there.
I just cooked an old 1.6.7 rom for you...wow did it bring back old memories.
Download 1.6.7 rom here: http://www.cinconet.org/titan/dcd 1.6.7 Rom.zip
Download 1.30.60 radio here: http://www.cinconet.org/titan/Titan Radio 1.30.60.zip
Put radio .nbh on the root of the card with a card reader. Force phone into bootloader and flash radio first. When it completes, remove the microsd card and replace the radio .nbh with the rom .nbh with the card reader. Insert the card again, force bootloader, and flash the rom. Remove the card and soft reset.
WOOOOOOOOT!!! it worked! Thanks gc14 for the files and awesome instructions!
i was with DCD 3.2.5 and wanted to flash to new telus wm6.1 from telus... now i'm stuck with bl spl-2.07...tried to flash back with stock rom Telus_HTC_P4000_WM6_07252007 but at 1% it says not compatible...tried also uni_exitbootloader but nothing happen...whenever tried to flash with SD card...it's always keep saying "loading...", is anyone have suggestion to bring back my mogul to life?
thanks
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
I would say the same. I would go ahead and unlock OliPro 2.4 (never tried 2.47) then flash Telus rom. After doing so you should be fine.
scrawnyb said:
uhh 2.07 is a relocker SPL
I think you have to downgrade to a stock firmware/SPL, then do the process properly.
Use SPL 2.40 or 2.47 before trying to flash on a GPS rom.
Click to expand...
Click to collapse
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
belmont said:
what do you mean by "I think you have to downgrade to a stock firmware/SPL" ? du you have any recommendation ?
Click to expand...
Click to collapse
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
scrosler said:
Sorry, I read his post wrong. HEre is what I would do:
1. Download OliPro 2.40 and run it. Ignore the part that asks you to verify the Active Synch connection. Its not needed for anything but a connection confirmation.
2. After running OliPro 2.40 you should be stuck at the three color bootloader screen, Like you are now. If not hold Camera and Power and use stylus to put phone in bootloader. Make Sure it says OLIPRO 2.40 for the version on the bootloader. If not then re-run oliupro and make sure to follow the directions. Especially noting that it asks you to disconnect then reconnect the device.
3. Flash your Stock ROM back.
4. Hard Reset.
In my experience you do not have to go back to a stock ROM to flash a new carrier ROM as long as you have OliPro.
Let me ask you this: What exact steps did you take when you flashed Telus ROM image?
I was on the same setup you were, DCD 3.2.5 with Radio .50 and OliPro 2.40. I simply flashed the Telus image and all was well for me. Hell it was better than all well. This is the best ROM I have ever used. PERIOD. No, its not pretty but damn, its fast as anything I have used and the GPS is insane!
BTW: Im a Verizon user. Anyone know how to make the phone not say "Telus" when I go to the connection manager?
Click to expand...
Click to collapse
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
belmont said:
thanks for quick reply. i tried so many times to use olipro 2.40...whenever i ran it...it popup that device is not connected and asked me to try again...tried also with SD but still hung on tri-color bars
Click to expand...
Click to collapse
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
scrosler said:
Thats interesting. I have hosed so many XV6800's and used OliPro and a stock GPS sprint ROM to get them back (Thanks alot for nothing Verizon!).
IM assuming you are still on the tricolor screen? Take out battery and place back in. Then try again. Dont wait long. Someonelse has discoverd the phone can only be connected for so long before it "drops" connection with the windows machine. Someone else's therory but I can certainly second it.
What SPL were you using with DCD 3.x before upgrading?
Click to expand...
Click to collapse
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
belmont said:
before flashing to new telus wm6.1 rom, i had olipro 2.40 with .30 radio and dcd3.2.5 kitchen...i have tried upgrading to radio .50 with no success. but failing to update radio didn't affect anything to my phone. tried your suggestion by romoving battery and still telling me that device not connected.
Click to expand...
Click to collapse
Hmmm, maybe try a different USB port at this time. Also, try this...
Before you connect your device open device manager in Windows. Look for M/S USB sync to appear after you connect. What OS are you using? This is what it will look like in Vista.
In XP I beleive it will show up under USB at the very bottom of Device Manager.
Does the phone show up at all?
Flash a stock pre-gps rom first.....then go ahead and upgrade the hard spl to 2.4 or 2.47.....then flash away with whatever you want....
You cannot flash Hardspl to Hardspl...they have overwrite protection not signed by HTC....
..................................