G'day...
I'm new to this whole thing so forgive this question...
I tried appling Hard-SPL-MFG to get started applying a new ROM to my 6800...
Now my phone is stuck on the bootloader screen... I've tried doing a couple hard resets, soft resets... everything.. all I get is the tri-colour bootloader screen...
The text on the screen is the following
(top right corner: RUUNBH)
Then,
TITA100
SPL-1.07.0000
CPLD-9
I've tried running the Hard-SPL package again, tried the radio setup, the DCD setup...
I've also tried reflashing to stock, but none of the updaters seem to be able to communicate with the device for some reason now...
Any suggestions on how to unbrick my apparantly now bricked phone would be much appriciated...
How are you flashing I would suggest using SD card Method. You will PROBLY have to flash to a stock rom since you have old bootloader and them from Windows Start the bootloader rom update. Then flash the ROM you want. This is what I would attemt.
Now my phone is stuck on the bootloader screen... I've tried doing a couple hard resets, soft resets... everything.. all I get is the tri-colour bootloader screen...
Click to expand...
Click to collapse
Have you tried using titan_exitbl to exit the bootloader?
Agree, the microSD card method works very well. However, keep in mind that some microSD cards will NOT work - so if it doesn't work, try to find a different microSD card.
"Have you tried using titan_exitbl to exit the bootloader?"
or try what the senior members suggest..thier usually more experienced
You have a bootloader for the pre-GPS ROMs. The install of the Olipro hard-SPL bootloader must not have completed successfully. If you flashed a new (3.xx) radio or ROM, you have an incompatibility between the bootloader, radio and ROM, and will probably not be able to boot the phone. Since you have that bootloader, you need to flash a pre-GPS ROM (2.xx stock ROM and 1.xx radio) so that you will be able to boot into Windows; then install Olipro 2.40 hard-SPL, and then after you confirm that the bootloader installed successfully, you can reflash the newer 3.xx ROM.
You should be able to flash a stock ROM package (which will include a compatible ROM and radio) from the bootloader screen, just ignore the wording about Activesync.
well i sorta have the same problem as u do mines stuck at Olipro 2.40 hard-SPL and i dont noe how to fix it either
oh yea mines was caused because my stupid USB cable disconnected itself during the bootloader update... its sorta broken
Note to self... update the Wiki page 'Titan Upgrade Problems and Solutions'
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
for being stuck at each tri-colour bootloader 1.07 (stock & locked), olipro 1.20 (unlocked & ready for 1.xx, 2.xx ROMs), and olipro 2.40 (unlocked and ready for 3.xx ROMs)....plus add a link a tip concerning titan_exitbl
duongtran, A BIG WARNING TO YOU, one way to actually brick a phone is to interrupt the unlocking or programming of a bootloader... DO NOT play around with modifying your bootloader with the state of your USB connection. As long as the bootloader is in good shape, a bad USB connection you can recover from an interupted radio or OS ROM flash.
As you hopefully have the olipro 2.40 bootloader functioning, your device is fine to boot into the OS of flashed 3.xx ROMs and their appropriate radio. You're welcome to get frustrated with your sorry USB or avoid it with the SD card ROM flashing method...
(sorry...on the ferry now and entering this via my phone..will either update the Wiki later unless another beats me to it)
roblab said:
G'day...
I'm new to this whole thing so forgive this question...
I tried appling Hard-SPL-MFG to get started applying a new ROM to my 6800...
Now my phone is stuck on the bootloader screen... I've tried doing a couple hard resets, soft resets... everything.. all I get is the tri-colour bootloader screen...
The text on the screen is the following
(top right corner: RUUNBH)
Then,
TITA100
SPL-1.07.0000
CPLD-9
I've tried running the Hard-SPL package again, tried the radio setup, the DCD setup...
I've also tried reflashing to stock, but none of the updaters seem to be able to communicate with the device for some reason now...
Any suggestions on how to unbrick my apparantly now bricked phone would be much appriciated...
Click to expand...
Click to collapse
guys is this thread still active?
Related
Here is a breakdown of what i did and whats happening.
1.2 ollipro installed already
loaded new radio
loaded new rom
Now the windows mobile 6.1 screen would come up and ask to tap screen but would reboot at this screen continously. I assumed this was happening because 1.2 ollipro was installed and not 2.4.
I then decided to reinstall my old radio and old rom and now the phone gets to the htc bootscreen and reboots immediately over and over again without getting far at all. What do I do?
For TELUS P4000
BOOTLOAD MODE
1. Try getting to the BOOTLOAD MODE by pressing POWER, CAMERA and RESET all a the same time
2. You should see at screen with red green blue white
New RADIO and CE ROM
1. Hard-SPL-240-MFG.exe/titan_SPL_2.40-olipro.exe (follow the instructions)
2. Run titan_radio_3.35.04.exe (very simple GUI instructions)
3. The titan will reboot by it's self, put it back in BOOTLOAD MODE
4. Extract dcd_titan_kitchen_3.0.0.rar to a directory and run BuildNB.bat (it takes a couple of min)
5. Select the stuff you want and don't forget you carrier (TELUS....)
6. Press the PLAY button (when finished, which is hard to see, when play is green) close the BuildOS
7. In a DOS windows it will build the CE ROM (follow the instructions)
8. Titan will reboot
i cant get 2.4 on there because i can get activesync up and when i get it to run through the boot load it gets to 100% in a split sec but leaves 1.2 on and not 2.4 even though it didnt record any errors
I'm having the exact same problem. Got the new Rom and radio installed. I had to go back to 1.2 to do it. But now i cant get 2.4 to install. I run the program it seems to install but still says 1.2 and is stuck on bootloader screen. even though it said itupdated to 2.4 anyone got any ideas on how to get 2.4 on there?
Try entering the Bootloader mode of Oliprio 1.20 and connect the USB to your computer.
Although it wont start an Active Sync session it will still allow you to load thing on such as a ROM or flashing program.
Well once you are in Bootloader and have a USB connection then try installing Oliprio 2.40
This might work.
Hi, ive done that and gone through the 2.4 install. after the RUU runs the progress bar goes across in like 1 second. it reports it successful but it still says 1.2 and is now stuck in the 1.2 bootloader. as if 2.4 never installed. any suggestions?
Furman69 said:
Hi, ive done that and gone through the 2.4 install. after the RUU runs the progress bar goes across in like 1 second. it reports it successful but it still says 1.2 and is now stuck in the 1.2 bootloader. as if 2.4 never installed. any suggestions?
Click to expand...
Click to collapse
So you installed 2.40. Well once you installed 2.40 go into bootloader again and make sure it is 2.40 and then try flashing the Radio first and then the ROM.
This is how i did it:
Installed olipro 1.2
installed radio 3.35
installed dcd sprint 3.0
Now like everyone else it continually reboots cause of olipro 1.2. So i put it in bootloader and it says 1.20 spl. So now i go to install 2.4 Olipro. RUU runs and the progress bar goes to 100% in about 3 secs. AFter it goes to 100% the mogul screen flashes and it says olipro 1.2 as if 2.4 didnt install even though on my comp it says that ruu update was sucessful. So im confused. I have tried it on my computer(vista64) and my old one xp 32bit. When the batch file is running it says "no device connected. would you like to try again?" w/ a yes/no/cancel. If i hit yes it just loops. if i hitno it will ask me this about 4 times then RUU will load
Ok, for anyone stuck with an older version of olipro and the new radio:
While in the bootloader, load an earlier version of your carriers rom. This should let you boot again and will let you install the newest 2.4 olipro bootloader so you can flash the newer roms.
If you can't find an earlier version of your carriers rom you will need to find an older radio rom and an older custom rom and flash both seperately to get it to boot.
Furman69 said:
This is how i did it:
Installed olipro 1.2
installed radio 3.35
installed dcd sprint 3.0
Now like everyone else it continually reboots cause of olipro 1.2. So i put it in bootloader and it says 1.20 spl. So now i go to install 2.4 Olipro. RUU runs and the progress bar goes to 100% in about 3 secs. AFter it goes to 100% the mogul screen flashes and it says olipro 1.2 as if 2.4 didnt install even though on my comp it says that ruu update was sucessful. So im confused. I have tried it on my computer(vista64) and my old one xp 32bit. When the batch file is running it says "no device connected. would you like to try again?" w/ a yes/no/cancel. If i hit yes it just loops. if i hitno it will ask me this about 4 times then RUU will load
Click to expand...
Click to collapse
Instead of running the RUU right after installing 2.4 over 1.2 try canceling the RUU and then manually enter bootloader mode in 2.4 and then install the RADIO following the ROM.
I figured it out. feel kinda stupid. was trying to install 2.4 from the boot loader of 1.2 forgetting that it needs to install files over to the phone before it flashes. :/ thanks foryour help though
Furman69...
I'm having the same problem. Could you post a step by step?
Thanks
I think I bricked it.
Actually I think I made a bigger mistake. I'm a VZW user, and I flashed the sprint/htc update hoping I could just flash dcd on top of that = stupid. The radio settings were all f-ed up. So I believe I read in the dcd 3.0.0 thread to run the titan relocker and then flash the stock vzw rom. Big mistake. Once I relocked it, It wouldnt let me flash vzw 2.09 and now my phone's in bootloader saying
TITA100
SPL-1.06.0000
CPLD-9
I think I'm screwed because It doesnt have a rom on there, so I can even unlock it. Any help would be greatly appreciated.
Flashing the sprint update, then flashing dcd on top of it would have been completely fine if you didn't let the sprint customizations run...i've done it to 3 phones already.
I don't really get what you're saying though. Are you stuck in the bootloader? Can you boot into any kind of rom? What happens if you try and soft reset, does the phone do anything?
gcincotta said:
Flashing the sprint update, then flashing dcd on top of it would have been completely fine if you didn't let the sprint customizations run...i've done it to 3 phones already.
I don't really get what you're saying though. Are you stuck in the bootloader? Can you boot into any kind of rom? What happens if you try and soft reset, does the phone do anything?
Click to expand...
Click to collapse
Yeah I wasn't that smart though . But yeah I'm stuck in bootloader. And I don't even know how to go about putting a ROM on there because it's locked. I've already tried to redo the Sprint/HTC 3.35 update, but to no avail. It says wrong vendor. I don't know... It's brand new too, that what sucks about it.
I finally got it to work after going back and forth installing old roms and radios and then installing 2.4 and then the radio and rom as ususal.
To be honest with you guys i beat myself up because i should of done it like this from the get go 2.4,radio, rom, and thats it but i read about people having trouble and dcds post, and I just went through more trouble that way. Thanks for the help.
If you're stuck in the bootloader, download the exitbl program to forcefully exit the bootloader. This will reset the phone. Tell me what happens after that. Does it boot any sort of rom? Does it just hang at a blank screen? Let me know.
Jaquers said:
Actually I think I made a bigger mistake. I'm a VZW user, and I flashed the sprint/htc update hoping I could just flash dcd on top of that = stupid. The radio settings were all f-ed up. So I believe I read in the dcd 3.0.0 thread to run the titan relocker and then flash the stock vzw rom. Big mistake. Once I relocked it, It wouldnt let me flash vzw 2.09 and now my phone's in bootloader saying
TITA100
SPL-1.06.0000
CPLD-9
I think I'm screwed because It doesnt have a rom on there, so I can even unlock it. Any help would be greatly appreciated.
Click to expand...
Click to collapse
I had a similar experience. Here is what I did.
I had the following installed before I started.
2.40 bootloader
3.27 radio
DCD 2.3.2 rom
I wanted to upgrade to the latest and greatest so I did the following. (This was before anyone knew about the 2.40 radio flashing issues.)
Flashed to DCD 3.00.
Failed Trying to flash 3.35 radio.
Read some more and like you tried to relock my phone using titanrelocker
Locked bootloader
Failed trying to flash Verizon Radio (downloaded from ppcgeeks.com)
Failed trying to flash Verizon Rom 2.09 (downloaded from ppcgeeks.com)
So at this point I was stuck in the original 1.06 Verizon locked bootloader, but I had 3.27 radio and DCD 3.00 rom.
Execed titan_exitbl.exe (included in 2.40 bootloader) in vista which returned a nice error. (Error accessing USB blah blah blah)
Execed titan_exitbl.exe in XP with ActiveSync and phone rebooted
Phone booted into Windows Mobile 6.1 and rebooted itself.
So I plugged the mini USB cable back in hopeing it might prevent it from rebooting. Luckily it did.
Reunlocked Bootloader using 1.20 olipro
Flashed 3.35 Radio
Flashed 3.00 DCD Rom again. (Just in case)
Phone booted into Windows Mobile 6.1 with mini usb cable still plugged in.
Upgraded bootloader to 2.40.
Re-Insert my NAM settings into EPST and rebooted.
*228 to get latest PRL.
Has been rock solid since.
Hello everyone i Just got a xv6800 and am trying to flash to a newer rom...However i cant seem to boot into the bootloader it just hangs at Loading.... There is nothing installed its factory rom and settings
Thx in advance
How are you attempting to load into bootloader?
The way I saw on the forums....holding power and camera button and hittig the reset..i get the tri color screen then it goes to Loading... and just sits there dosnt do anything else
Do you have a microsd card in while trying this? If so, does it contain any .nbh files on it in the root directory? If so, do you have a TITAIMG.nbh file in the root directory?
The only way the bootloader would try loading something the way you're describing is if this is the case.
I agree with gcincotta.
If you are in fact trying to flash from the SD card though, most people have reported that it won't work using an SDHC card. It needs to be a standard (non high-capacity) card.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Well i got it to go to usb but now the .exe file for the 2.40 unlocker wont run on x64 systems so i guess im out of luck huh
Did you already run the unlocker? If so, you should be ready to flash a custom ROM. It is normal to be stuck in the bootloader after an unlock. Just flash away.
If the unlock did not go successfully, you will have to try again, making sure to follow directions precisely (on a 32bit system preferably, less headaches). To unlock you must be booted up into Windows Mobile. You can try the exit bootloader program from the PPCGeeks Titan Upgrade forum, or try flashing a stock ROM to get back into WM.
Edit: You can tell if the unlock was successful by looking at the SPL in the bootloader (right under TITA100 MFG). It should now say SPL-2.40.Olipro. If it does not, try the steps above to get back into Windows Mobile.
I did have a card in it..now i took the card out and it goes to tri color in the red i get tita100 and i the white i get serial...thats all it does now
Click to expand...
Click to collapse
You need to be more specific. Everyone's titan says TITA100. What SPL is installed? Post the entire contents of your screen and then we can get somewhere.
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
I was able to udate to 2.52 rom...the 3.04 wasnt working correctly and it would not up date using *228..and there was no sound...i was not using the radio 3.35 because i heard people saying that it was a bad one to use...is there much difference in performace between 2.52 and the 3.04?
So I need to install Sprints 3.35.651.2 rom and not let the sprint customazations run.
Then use the unlocker 2.4
Then use DCD or No2Chem custom rom.
craig540 said:
I have a new 6800 from Verizon.
software 2.09.605.8
firmware radio 1.30.60
pri ver 1.35.002
pri check 11ab822d
SPL-1.04.000
Do I need to unlock it first ?
Which unlocker do I use ? is it TitanUnlocker.exe
Then the way I read it I need to first flash the Sprint ROM 3.35.651.2
Then what ever rom I want after that.
Click to expand...
Click to collapse
You are starting from scratch with an unlocked phone. Before rushing forwards you have some reading to do:
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
All of your answers are there.
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
craig540 said:
Yes I have read many threads and think that is why I am so confussed. I upgraded from a 6700 which I had flashed to WM6 many times before.
I will follow your linked procedure.
Two questions.
Is my phone being stock and never flashed before locked or unlocked, and do i need to run Olipro 2.40 by executing Hard-SPL-MFG.exe or start with the Sprint Radio (3.35.04)
Also the tutorial says Upon its completion, press the power, camera and reset buttons to force the phone into the bootloader/SPL mode.
What will I see to let me know it is finished loading.
Thanks for your reply.
Click to expand...
Click to collapse
1st- update to 2.4 olipro
2nd- update sprint 3.35 rom (stop at the "tap the screen" customization screen) this gives you the radio
3rd- from customization screen start the 3.0.4 rom and flash that rom
Your phone will restart after loading and will boot into wm6.1
4th- Read untill you understand before flashing roms
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
craig540 said:
After 2.4 olipro do I hit reset to let it boot up again or start the sprint rom while its still in bootloader mode
Click to expand...
Click to collapse
Does not matter, if you do it in rom it will force into bootloader anyway.
Ok up and running dcd 3.04
date 2-22-08
radio 3.35.04
I did not let sprint cutomazation run.
Tried to make a call and get message saying verizon can not authenticate and to dial #8899
Should I do that now?
Had to call VZW to get new A-Key
No GPS detected in google maps is there anything I need to do to set it up ?
Try installing VisualGPSce -- it's a good little & free diagnostics program too see GPS satellite reception.
....after seeing that running on COM4 at 4800 baud, then you should see a list of visible satellites. Now, whether or not you get a sufficient lock within the first half hour depend's upon your luck in the draw for a GPS functioning Titan -- GPS hardware-wise, not all are equal.
Hi there, I have very minimal experience with this stuff so I will provide as much detail as possible...
I had previously successfully programmed my HTC6800 back in March by unlocking with Olipro 2.4, then I flashed the radio with 3.27 and used dcd 2.3.2 for Bell on it. Now my memory is a little foggy as that was several months ago however I made it through the process fine. This encouraged my to try to update again today. I tried following the steps in the wiki as I could not find the guide I had used previously. I already had Olipro 2.4 so I was good at that step. I then tried running the newest radio update and it would not take. It gave me an error. I reset the phone and tried several times but to no avail. I then tried putting on dcd3.2.0 which went fine. THe phone rebooted and I made a test call and everything was fine. I however wanted the new radio update still so I thought I'd take another crack at it... it still would not update. In the wiki it said about relocking the phone and putting it back to the factory ROM and starting again. So I did this, I downloaded the relocking util and followed the instructions to relock the phone. That went fine... Olipro is gone and is shows the 1.06 like it's supposed too... next it said to put the factory ROM back on... well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
So currently my 6800 sits as the 3 colour screen with 1.06 relock on it and does nothing else. It has radio 3.27 on it and dcd 3.2.0.
Is there any way to fix this?????
Run this first to exit the bootloader and get into windows mobile. Then check out which rom you are on (I think you were on dcds rom). Then load radio via sd card method listed in the wiki. Then reload dcd if you are not already on the version that you want.
P.S. I have heard things about that ROM that it caused problems. You may want to read up on that here.
Nope
Well, I downloaded the file and tried running it but to no avail. It just comes up saying that the application failed to start because RAPI.DLL is missing.
Also
I tried running that app on a Vista machine as well and it just says that it can't open the USB port. However, windows found the device and installed a driver for it when plugged in AND it shows USB on the bootloader screen when plugged in.
ok..,. let me see...
try installing olipro 2.40 again, it seemes that your phone is locked (olipro 1.06) so it can't run the dcd custom rom... reset and see if you can enter windows...
then if you enter windows normally, downgrade to olipro 1.20 and install the new radio, then, once again upgrade to olipro 2.40 so it can enter windows...
let me know if it worked for you...
Evo69 said:
well, I am will Bell and the link for the factory ROM is dead! I can't get it anywhere!!!
Click to expand...
Click to collapse
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Here's the problem
OK. Here's the problem. I obviously misread the instructions on setting the unit back to stock as I just read them again and I realize my mistake. I did not load the stock ROM on first. I used the Re-lock program and re-locked my unit before putting the stock ROM back on. So I sitting at the 3 colour screen with SPL 1.06 and I have radio 3.27 on the unit and dcd's latest ROM on it. I can't get it past the 1.06 bootloader. I have tried a hard reset, I have tried the program above to exit the boot loader and it does not work. Is there any way I can get Olipro 2.4 back on or exit this bootloader???
just connect your phone to the computer (it's ok to be on the tri color screen) and install olipro 2.40 from the computer...
you just need to be sure that when you connect the phone in the tri color screen it says USB...
i'm attaching Olipro 2.40
No Dice
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
i had a similar problem yesterday when i tried to upgrade the radio form 3.42.02 to 3.42.30 and taht solved my problem...
so you basically cannot exit the bootloader mode?? even when you hard reset your device??
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Evo69 said:
Nope. I had tried that already. I just tried again. When I run Olipro 2.40 the command prompt comes up and then come up with a window saying "Cannot Find Device" (or something VERY close to that). It then asks if you'd like to retry, clicking retry just keeps bringing up the same message. If you click "No" on retrying it will eventually move on to the next step and load up the flash program. It will then attempt to flash the unit (Grey screen with the status bar comes up) but it just sits at 0% and eventually comes up with a 242 communication error.
Click to expand...
Click to collapse
I have the Bell ROM if you're looking for it.
TS
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
jhamilton said:
I didn’t think it was possible to flash back to a stock Bell (non-GPS) rom/radio after flashing to a GPS radio.
Does anyone know if it’s possible to flash the SPL (bootloader) from an SD card?
No2chem over at ppc geeks has a new SPL that loads from the device, but it needs be running.
http://forum.ppcgeeks.com/showthread.php?t=30561
Click to expand...
Click to collapse
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
YES
Timeshell said:
I have the Bell ROM if you're looking for it.
TS
Click to expand...
Click to collapse
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Keystone said:
Install another carrier's stock ROM (though to keep things easier avoid the Telus one as it doesn not include a radio ROM) and avoid letting it run any customisations after boot/screen calibration.
You are fine.
Click to expand...
Click to collapse
I tried using a Sprint one... it would not work.
Timeshell said:
I haven't tried to do it yet, but I did develop a theoretical how to before I first flashed my phone as I wanted to make sure I had a way out. You can find it here:
http://forum.xda-developers.com/showthread.php?p=2017265&highlight=bell#post2017265
Click to expand...
Click to collapse
Yeah I've heard some horror stories when it came to downgrading, including a few bricked devices.
http://forum.ppcgeeks.com/showthread.php?t=26082
I would be interested to know if anyone on Bell has managed to successfully downgrade a 6800 to stock.
i thought dcd's new 3.2.0 needed a radio of 3.35 or higher to run and does not flash the radio when u flash his rom. Another problem with the phone not coming out of the bootloader is that you have to disable usb connections in active sync or windows mobile device center for the exit bootloader app to work. Try disabling the usb connection in whichever one applies for you and run the app again. If you can get out of the bootloader try to go back to ollipro 2.40 or use one of no2chems bootloaders as they work from the device and an sd card no need for a pc to flash the bootloader. once bootloader is unlocked again run a full radio/rom update like the sprint stock 3.35 easily found on htc's website under the titan (us version of the site). Don't let the carrier custimizations run ... the file that runs after u calibrate screen and set timezone just pull the battery. Then grab whatever rom / radio you want to or were trying to flash 2 before and name it put it on the root of an sd card (thats under 2gb and formatted to fat32) and rename the ruu_sighned.nbh file to TITAIMG.nbh hold power + camera and hit your soft reset button. The tri color screen will come up and should say loading then promt to hit the power button to flash and show u what u r flashing. cdma (radio). os (radio rom) or splash screen, or whatever you r trying to flash hit power button to start once done it will sit with update complete on the screen pull the battery out for about 30 sec and put it back in reboot and enjoy the custom rom or radio.
kdj67f said:
Can the unlocker be flashed from a memory card? Has anybody ever tried?
Click to expand...
Click to collapse
You can use nueSPL 2.47 to load the locker/relocker but you need to be booted into WM6 to do so. You need to reload another rom that uses the bootloader you have currently loaded and then you can move forward or backward.
Evo69 said:
Ya, if you can post attach that file to a posting on here I would appreciate it. If you need an alternative method of send the file to me just PM me and I will figure something out.
Click to expand...
Click to collapse
Uploaded to Rapidshare
http://rapidshare.com/files/1271390...3.666.1_RS_1.37.30_BM_1.27_0604_SHIP.zip.html
TS
i installed the wrong rom on the wrong hard spl. i had the hard spl a 1.30 installed and dcd 3.2.0. now the screen is stuck at the loading screen that says htc smart mobility. and no radio at the bottom. please help and the phone wont sync.
Good luck on that.. You installed a bootloader for a different model -- likely the TyTn or Trinity. What phone do you have? What instructions did you follow?
If you do have a Titan, then possibly via the SD Card you can change the bootloader to the new 2.47 (I haven't played with it yet but another may provide a solution). You are likely out of luck in flashing to any of the other Titan bootloaders as you must be able to boot into the OS, but with you error of installing an inappropriate bootloader you are out of luck there.
no it was a bootloader 1.30 for the titan
Your information is incoherent.
What rom/bootloader did you have prior to updating?
What rom/bootloader did you try to upgrade to?
You need a minimum SPL of 2.40 to install DCD 3.2.0
I use 2.47 from no2chem and it works great. http://forum.ppcgeeks.com/showthread.php?t=30561
Are you able to boot up the device? If so copy the SPL 2.47 to the card then to the PDA and run it from there.
If not, put the PDA into Bootloader mode and try to install Olipro 2.40
http://www.lifesnotsogood.com/dcd1182/titan/spl/titan_SPL_2.40-olipro.exe
Failing that you can try to flash back to an official ROM if you have one.
You need to soft reset your phone while holding the Camera and power buttons. This will force your phone in to the bootloader. You should then be able to reflash to lower ROM. Then you need to search for Olipro or whatever the 2.40 bootloader is. Your best bet after that is to flash the official Sprint 3.35 Radio and Rom then flash to DCD's.
**Edited**
Sorry Hamilton didn't realize you gave a link to the 2.40 bootloader.
If he is sure that it is "bootloader 1.30 for the titan" then I know of NO such bootloader. He has likely installed the wrong bootloader (for another device) and therefore no amount of flashing to an OS ROM will help him boot into the OS. Unless via an SD card for 2.47, beastmode216 is stuck with a borked device.
So, beastmode216, I'll ask again, where did you get such instructions and where did you source your bootloader 1.30?
What is one of the earlier bootloaders? I was thinking my Mogul orginally had something like 1.30 or 1.40.
thanks guys but the problem is solved. just make the phone go in to the bootloader
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
calash said:
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
Click to expand...
Click to collapse
My mistake, as pointed out by gc14 the stock bootloader is 1.04.
Ahh, ok, my fault as I thought that he had also installed a bootloader under the name of 1.30.. That could've been an unlocker for a TyTn or another device.
Correct, OEM bootloader should be 1.30.60.
Click to expand...
Click to collapse
This is incorrect. The stock bootloader is 1.04. The stock radio is 1.30.60.
SPL 1.30 does NOT exist for the Titan.
Stickies exist for a reason...to read them as they contain valid, useful information. http://forum.xda-developers.com/showthread.php?t=392133
Check your current bootloader
1. Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
2.
Hit POWER-CAMERA-RESET to check what version of bootloader you have installed.
* At the tri-colour bootscreen you will see the version number installed.
* if it is 1.04 or 1.06 then your Titan is locked and has the correct bootloader to flash to the stock ROM of your choice --> skip to step III
* if it is 1.20, 2.40, or 2.47 then your phone is unlocked with a third party bootloader and must relock your phone.
---------------------------------------------------------------------------
I have a Sprint HTC Mogul and have been shuffling through all the threads and still confused, sort of...
I am at the Tri-color screen and none of those version number matches mine.
on my tri-color screen it displays:
Tita100
SPL-2.06.0000
CPLD-9
i searched the board and found but it didnt give me a clear answer.
http://forum.xda-developers.com/showthread.php?t=284404
So far i have downloaded
Sprint Cab
dcd_titan_3.2.5.exe
Titan_Radio_ROM_3.42.40.exe
[OliPro MFG 2.40] (Hard SPL)
I'm hoping someone can help me figure this out, whether or not i need to downgrade/upgrade.
And Also was wondering what type of neat things i can do with the roms/kitchen im a total noob at this but trying to make sense of all of this.
Other Phone info:
rom Version 3.35.651.2
radio ver. 3.35.04
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
scrawnyb said:
flash back to a stock (non-GPS if I remember right) ROM from there.
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
You are right on the money.......
that should be the stock bootloader for a stock gps rom.
if you want a custom rom you will need to unlock using 2.40 or 2.47.
kitchens just allow you to cook in apps that you want instead of installing them later. the problem is the install is permanent and they cannot be removed.
i prefer to flash a clean rom and install my apps later.
im pretty sure 2.06 is the temporary bootloader used by no2chem's nueSPL to ram with 2.47. if your bootloader shows 2.06 you will need to flash nueSPL again as it did not flash correctly. 2.07 is nueSPL Relocker.
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
lafester said:
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
Click to expand...
Click to collapse
it happened to me, although i didnt get stuck. it was flashed on a card that isnt flashing compatible (telus). i only noticed because it didnt reset itself like it said it should have. returned the card, got a San Disk, and reflashed nueSPL. this time it soft reset itself, and displayed the correct bootloader, 2.47.
I got stuck in 2.06 last night... earlier in the day I dropped my mogul in water and somehow cracked the screen at the same time. After drying everything out for 12 hours the phone came on with barely anything on the screen, I got the phone into bootloader (it was at 2.47) flashed a stock sprint rom, I immediately ran the nueSPL relocker (had to use my mobler to see the screen), after the relocker ran I was stuck in a 2.06 bootloader for some time, eventually I got out of the bootloader (not quite sure how... I flashed the stock sprint rom a few more times and mash some buttons) eventually I was able to run the relocker again and get my phone back to 2.07... a little bit of trouble but it was worth it now that I know I should have absolutely no problems getting a new (probably refurb) phone through TEP
scrawnyb said:
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
My phone is stock, i hadnt done anything to it yet. Im just unsure what to do because 2.06 was not shown at the step-by-step instructions.
so let me see if i understand what i need what to do....
flash the current rom, stock 2.06, with [OliPro MFG 2.40] (Hard SPL)
then run dcd_titan_3.2.5.exe and Titan_Radio_ROM_3.42.40.exe
then Sprint Cab??
Thanks for the replys