phone is stuck at htc screen and it says no radio - Mogul, XV6800 ROM Development

i installed the wrong rom on the wrong hard spl. i had the hard spl a 1.30 installed and dcd 3.2.0. now the screen is stuck at the loading screen that says htc smart mobility. and no radio at the bottom. please help and the phone wont sync.

Good luck on that.. You installed a bootloader for a different model -- likely the TyTn or Trinity. What phone do you have? What instructions did you follow?
If you do have a Titan, then possibly via the SD Card you can change the bootloader to the new 2.47 (I haven't played with it yet but another may provide a solution). You are likely out of luck in flashing to any of the other Titan bootloaders as you must be able to boot into the OS, but with you error of installing an inappropriate bootloader you are out of luck there.

no it was a bootloader 1.30 for the titan

Your information is incoherent.
What rom/bootloader did you have prior to updating?
What rom/bootloader did you try to upgrade to?

You need a minimum SPL of 2.40 to install DCD 3.2.0
I use 2.47 from no2chem and it works great. http://forum.ppcgeeks.com/showthread.php?t=30561
Are you able to boot up the device? If so copy the SPL 2.47 to the card then to the PDA and run it from there.
If not, put the PDA into Bootloader mode and try to install Olipro 2.40
http://www.lifesnotsogood.com/dcd1182/titan/spl/titan_SPL_2.40-olipro.exe
Failing that you can try to flash back to an official ROM if you have one.

You need to soft reset your phone while holding the Camera and power buttons. This will force your phone in to the bootloader. You should then be able to reflash to lower ROM. Then you need to search for Olipro or whatever the 2.40 bootloader is. Your best bet after that is to flash the official Sprint 3.35 Radio and Rom then flash to DCD's.
**Edited**
Sorry Hamilton didn't realize you gave a link to the 2.40 bootloader.

If he is sure that it is "bootloader 1.30 for the titan" then I know of NO such bootloader. He has likely installed the wrong bootloader (for another device) and therefore no amount of flashing to an OS ROM will help him boot into the OS. Unless via an SD card for 2.47, beastmode216 is stuck with a borked device.
So, beastmode216, I'll ask again, where did you get such instructions and where did you source your bootloader 1.30?

What is one of the earlier bootloaders? I was thinking my Mogul orginally had something like 1.30 or 1.40.

thanks guys but the problem is solved. just make the phone go in to the bootloader

Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader

calash said:
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
Click to expand...
Click to collapse
My mistake, as pointed out by gc14 the stock bootloader is 1.04.

Ahh, ok, my fault as I thought that he had also installed a bootloader under the name of 1.30.. That could've been an unlocker for a TyTn or another device.

Correct, OEM bootloader should be 1.30.60.
Click to expand...
Click to collapse
This is incorrect. The stock bootloader is 1.04. The stock radio is 1.30.60.
SPL 1.30 does NOT exist for the Titan.
Stickies exist for a reason...to read them as they contain valid, useful information. http://forum.xda-developers.com/showthread.php?t=392133

Related

How to reflash original SPL over SPL2.10.Olipro?

Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
rakdoll said:
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
Click to expand...
Click to collapse
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
This guide assumes you already have flashed ROMs and Other components and you are familiar with the process.
NOTE: By downgrading your SPL version your device is more vulnerable to being permenantly bricked if a flash goes wrong, by following this guide through YOU accept responsibility for any problems faced due to this operation. As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
Click to expand...
Click to collapse
And *that* is the reason we helped you, so that now you help others. One day, rakdoll will help someone else. That is why we are all here. Nicely done!
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
revert back
this is what i used to flash mine back to enable original rom to be installed ,so i could take phone back for warrany reasons
Korpse said:
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
Click to expand...
Click to collapse
Shouldn't need to access OS. You should be able to do it by putting it in BL mode... THEN plug it into the usb. Then start the updater.
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Korpse said:
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Click to expand...
Click to collapse
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Korpse said:
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Click to expand...
Click to collapse
Oh interesting. A nuance I hadn't picked up on. So, when using the Force using SSPL" option in the flashing utility, you must be able to access the Phone OS? That surprises me, I thought that the RUU utility would put it on the phone even in BL mode and execute it? Hmm... strange. I guess if it is an exe, it needs the OS to run, though. Sort of makes sense. Sorry about the misdirection.
todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Hi,
I'm trying to downgrade to the original SPL (I'm trying to get hold of 2.03 but can't seem to find it), so am using 1.06. I've been able to downgrade to Oli1.10 from Oli2.10, but it won't go back to 1.06 from there, after the RUU says successfully completed the SPL is still the same.
Any ideas?
Cheers
downgrade phone for rogers warranty
Hi Guys,
I need to downgrade my phone as well for warranty purposes. Unfortunately Mrvanx's guide is offline at present. Can any one of you give little further detail about what I need to get back to orginal rom/radio/spl and bootloader. Or in shor to be able to send it back for warranty. I do have a new Rogers phone if that can be of any help.
It is from Rogers and currently my boot loader screen says following:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro
Under Device Information:
ROM version: FARIA.R-32
ROM date: 11/06/07
Radio version 1.54.07.00
Protocol Version 32.86u.7020.23H
ExtROM version: BIGSTORAGE
My replacement Rogers Phone has following:
HERM200
IPL-1.01
HERM200
SPL-1.11
Under Device Information:
ROM version: 1.34.631.14
ROM date: 04/17/07
Radio version 1.42.00.00
Protocol Version 32.75.7020.18H
Can anyone please tell me if it is even possible to do this downgrade.
Thanks
B.
why dont you just brick the phone if you are worried about them complaining over the boot loader version. If you cant access the phone i doubt they will be able (or even be bothered) to
Could you please let me know what you did? Did you downgrade To the original Rogers Radio and SPL ? Do you by any chance have all the original Rogers files (WM5, SPL, Radio,...)?
I am with Rogers too and just unlocked SIM (not CID) and installed WM6 (official HTC)
I am wondering how I could lock SIM again if I need to return the phone for Rogers warranty? or unlocking SIM does NOT void the Rogers warranty?
Thanks
Downgrade to SPL 1.11
Hi is anyone able to figure out how to downgrade from SPL 2.10 Olipro to SPL 1.11? I have tried Mr Vanx guide but at the end of the process, I get Error 260. Not sure if I am doing anything wrong.
Do I have to downgrade to SPL1.10 Olipro, before I downgrade to SPL 1.11?
Thanks
I am having some issues downgrading back to an original SPL. I've searched throughout the site and have found a lot of conflicting advice, although this thread seems to be the most relevant.
I started out the process with SPL: 2.10.Olipro
I downgraded to 1.10.oli.
This process was successful in that the bootloader screen now says that the SPL version is 1.10.oli.
Now, when I try to flash the OEM version of SPL, the phone asks the following question:
You would like to run jumpspl.exe
If I say yes, the screen goes gray and says load... but I end up with a 260 error.
I have tried turning off the usb connection in the active sync and starting from the bootloader as mentioned here, but that just ends up giving me a 264 error.
Any suggestions would be appreciated.
Cheers,
~Hat
* edit *
Post #5 from here fixed the issue.
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
<snip>
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Click to expand...
Click to collapse
Okay, Im back to 1.10oli, but how do I know if I need to go back to SPL 1.04 (includes IPL 1.00) or SPL 1.06 (includes IPL 1.01)?
OK people, please tell me you have looked at the updated guide right??
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=19&Itemid=27
Yes, but the choices are,
1.04
1.06
1.09
1.11
2.03
and I don't know how to tell which one is stock for my phone. I assume I need 1.04 since my bootloader says IPL-1.00 but I'm not sure because I know that used to say IPL-1.04, and since it appears that that can change for some reason, I want to make sure I get this right so I can get this waranteed. Im going to sell it on ebay and get the new HTC Fuze as soon as AT&T releases it.

Wiki states instrux for 1.06 but not 1.04 bootloader

My bro has a Titan and is thinking about having me upgrade but I saw that his bootloader version states 1.04 not the 1.06 that mine was when I flashed (and also the one that the wiki says too). Is the process the same? Should I just use unlocker then upgrade to 2.40 then install radio then DCD? A little wary as it is not my phone. Please be specific when answering. I am planning to do the most recent radio and rom.
serfboreds said:
My bro has a Titan and is thinking about having me upgrade but I saw that his bootloader version states 1.04 not the 1.06 that mine was when I flashed (and also the one that the wiki says too). Is the process the same? Should I just use unlocker then upgrade to 2.40 then install radio then DCD? A little wary as it is not my phone. Please be specific when answering. I am planning to do the most recent radio and rom.
Click to expand...
Click to collapse
In order to flash a dcd rom you need 2.40...Go through the same process you would in order to flash a 3.1.x rom.
prepsssuck said:
In order to flash a dcd rom you need 2.40...Go through the same process you would in order to flash a 3.1.x rom.
Click to expand...
Click to collapse
So it still needs unlocker then 2.40 right? or is unlocker unnecessary now?
Who is his carrier? As forthe bootloader question, I'd be asking Ollipro... I've not seen a bootloader 1.04....
azclown said:
Who is his carrier? As forthe bootloader question, I'd be asking Ollipro... I've not seen a bootloader 1.04....
Click to expand...
Click to collapse
bootloader 1.04 is the "stock" verizon bootloader you should still update to the 2.40 if you plan on having any 3.xx.xx radio's
Just to clarify...
When the phone ships it comes with SPL-1.04 which is the stock bootloader, which is why it doesn't say Olipro.
1.06 is also a "stock" bootloader provided by Olipro which allows you to flash stock roms/radios.
Edit: WINGS 1 - PENS 0!!!!!!
gcincotta said:
Just to clarify...
When the phone ships it comes with SPL-1.04 which is the stock bootloader, which is why it doesn't say Olipro.
1.06 is also a "stock" bootloader provided by Olipro which allows you to flash stock roms/radios.
Edit: WINGS 1 - PENS 0!!!!!!
Click to expand...
Click to collapse
Thanks, I have been flashing since the time you needed the old Olipro to flash the radio and when my brother once before flashed going straight to 2.40 it caused problems. I haven't had a new phone since then and wondered if the unlocker was still necessary. I am gathering that it is not and that you can go straight to 2.40, am I correct?
mogul with slight crack along the frame of screen
i've been reading for a while, and someone wrote that it doesn't matter about the bootloader when returning the phone to the store as long as you have the stock rom. i'm using the newer stock rom (3.35), though i did use the unlocker to put olipro 2.40 on it a while ago to mess with other roms.
the work order for the replacement mogul is already in and it (the new or refurbed mogul) should arrive tomorrow or the next day. should i go through the trouble of putting the stock bootloader on there if i already have the newer stock rom from htc/sprint on my phone?
also, i read that sprint has no warranty (or it's only 30 days). i use total equipment protection for $7 per month (which is how i'm getting a new or refurb mogul because of a case fracture). i'm using the newer stock sprint rom (with gps) and my bootloader says olipro 2.40.
does anyone think that i should be worried if i don't do anything before the new one arrives and just give them the cracked one?
i clearly didn't read the terms and conditions closely enough to find anything that tells me not to modify the bootloader or really ANYTHING about the bootloader...is total equipment protection a warranty that i could possibly void by putting olipro 2.40 on it even with the sprint official 3.35 installed?
I wouldn't worry about it. 1.06 is not the official stock bootloader either, 1.04 is, and I've swapped out my xv6800 a couple times with 1.06 on it and the Verizon stock rom. They don't usually check the bootloader. Just make sure the new Sprint stock rom is on there with radio 3.35.04 and you should be fine.
thanks much for your quick reply. i'll rest easier tonight.

Successful Relock and Flash of an XV6800

I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
I had to turn my Titan in for a replacement. Knowing about relocking breaking the usb port, I figured I'd do it anyway and just flash via the SD card. Well to my amazement I was able to relock and flash the OEM Radio and Software without and problems. Once it booted up Activesync connected and charge light came on.
Just figured I'd share since there is so much fear about relocking.
Went from 3.56 based ROM and 3.42.30 Radio back to OEM.
Click to expand...
Click to collapse
I'm not sure what you mean about fear of relocking and relocking breaking the usb port.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
http://forum.ppcgeeks.com/showthread.php?t=21953
Read first post
This is only a small example but I'm sure I could find more than 10 instances of this throughout threads. Including NO2Chem saying not to do it aswell.
The story on the street has always been.... DONT go from a GPS to a non-GPS radio. Something about how it will screw up the USB port.
Click to expand...
Click to collapse
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Read the first post in the link I gave you. Then you can do a search on downgrading issues to find more reports.
I know it can be done because I've done it on 2 different Titans now. I made the thread to help prove that it can be done so other arent so scared by the rumors as you call it.
gc14 said:
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
Exactly... I'm attempting to put the rumor to rest. Atleast as far as Verizon customers are concerned.
What SPL are you using before relocking to 1.06?
yep
Rom 2.09
Radio 1.30
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
lllboredlll said:
yep
Rom 2.09
Radio 1.30
Click to expand...
Click to collapse
I am not sure if you answered his question. Which bootloader are you running, nueSPL or other?
I have heard some concern with reverting to non-GPS stock using the no2chem tools, but obviously there is no worry with the relocker and such.
gc14 said:
I think you misunderstood me....SPL = bootloader.
What bootloader are you using before relocking?
Click to expand...
Click to collapse
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
It gets hard to think straight with people flying in and out of my office every 5 seconds. I'll try to read a little more throughly next time.
Sorry I misunderstood you. I was running 2.40 before taking it back to 1.06.
Click to expand...
Click to collapse
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Now all there is left to do is link this to ppcgeeks and be done with the rumor. Thank you for your input....
gc14 said:
In my encounters with going back and forth, this is what I've come up with (for Verizon users):
If using SPL 2.47, steps to relock are as follows:
- Install Olipro 2.40 via USB
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
(DO NOT EVER USE nueSPL Relocker!!!)
To get back to SPL 2.47 from stock, all you need to do is run nueSPL Unlocker and use the microsd card to go from SPL 1.06 right to SPL 2.47, then flash a 3.x.x rom/radio. Going FROM SPL 1.06 TO SPL 2.47, SPL 2.40 is not needed.
If using SPL 2.40, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 2.40 from stock, all you need to do is run Olipro 2.40 via USB, then flash a 3.x.x rom/radio.
If using SPL 1.20, steps to relock are as follows:
- Install SPL 1.06 using Titan Relocker via USB
- Flash stock rom/radio
To get back to SPL 1.20 from stock, all you need to do is run TitanUnlocker via USB, then flash a 1.x.x rom/radio.
Click to expand...
Click to collapse
I vote to have this added to the return to stock wiki. GC will you post?
How about USCC?
Brings me back to my previous question, GC (Previous Thread); How can I back-up the current ("Stock" for USCC) OS ROM and RADIO on my new Titan? It was discussed that it [dumping current ROM and Radio and then using dump to re-flash] couldn't be done. I wanted to do a ROM dump before flashing to DCD's so that I could revert to it if needed; also, so that I could re-flash to "stock" on my old unit before sending it back to USCC... however, I don't how to accomplish this, if at all possible to do so!
If anyone can guide me through this, I could upload the USCC "Stock" (for lack of a better word, since USCC has no actual "Stock" Roms) ROM and RADIO and make it available to other unfortunate USCC customers. I agree w/Serfboreds, and also vote to have this thread added to the "Return to Stock" Wiki.
Thanks, Guys!!
gc14 said:
I have never heard that story, nor have I ever had any problems going back and forth between GPS and non GPS radio.
While testing the new Sprint PRI way back when 3.49 came out (I'm on Verizon), and now testing the new Verizon update, I've had to go back to stock more times than I can count and have never ran into any issues.
May I ask where you found these rumors?
EDIT: Ahhh ppcgeeks...yeah don't really frequent those forums much. Not sure why n2c would say something like that because like I said, I've probably gone back and forth between GPS/Stock at least 15-20 times with no problems at all.
Click to expand...
Click to collapse
I think the issue lies with Sprint customers..... I personally have reflashed to stock at least 15-20 times.... from a GPS ROM and back.....
That is a very nice summary of steps for re-locking from various spl's and definately needs to be entered into the !iki.... If GC doesn't have time I'll do it when I get done here at the dentist.... booooooo....
I think the real issue was going from bootloader nueSPL 2.47 to a stock GPS rom caused problems. But because verizon customers dont have a stock gps rom to flash back to we go to a non-gps (1.XX) radio which does not cause the problem.
No2chem originally made the advice not to go back to a stock assuming stock included 2.XX or 3.XX radios. Once he was alerted to the fact that going back to stock 1.XX (i.e with verizon) did not cause a problem he modified his warning advice.
Once again, the warning is only valid for bootloader nueSPL 2.47
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
GC, does going from nueSPL 2.47 to olipro SPL 2.40 prior to relocking negate problems for everyone? I ask that question because I have refrained from moveing to 2.47 for fear of problems in the future. As far as I can see the benefits of 2.47 are marginal at best. But if I have a sure fire escape mechanism I might upgrade my bootloader at some stage
Click to expand...
Click to collapse
Yes, it negates the problems.
gc14 said:
Yes, it negates the problems.
Click to expand...
Click to collapse
Thanks dude. And I agree with Serfboreds that you should add this advice to your wiki. Very easy to understand and maps out all (most) of the possible relock escape routes.
Once again gc you are a font of wisdom.
ugh.... i can't keep up with all the misinformation anymore. If it works for you verizon users in your personal experience though good for you. I know for a fact it can cause problems. I'm starting to narrow it down to the original 3.35 leaked rom with GPS radio from sprint, but have no firm proof it's that narrow scope yet . Still have myself a brick from the GPS to pre-gps and I didn't use nueSPL Relocker thats for sure =P
For more info on the problem and others that experienced this "rumor" first hand go to ppcgeeks and search for "download mode"

at a lost, SPL-2.06

Check your current bootloader
1. Hard reset your phone by holding down both softkeys, hitting reset, and pressing R (just for good measure)
2.
Hit POWER-CAMERA-RESET to check what version of bootloader you have installed.
* At the tri-colour bootscreen you will see the version number installed.
* if it is 1.04 or 1.06 then your Titan is locked and has the correct bootloader to flash to the stock ROM of your choice --> skip to step III
* if it is 1.20, 2.40, or 2.47 then your phone is unlocked with a third party bootloader and must relock your phone.
---------------------------------------------------------------------------
I have a Sprint HTC Mogul and have been shuffling through all the threads and still confused, sort of...
I am at the Tri-color screen and none of those version number matches mine.
on my tri-color screen it displays:
Tita100
SPL-2.06.0000
CPLD-9
i searched the board and found but it didnt give me a clear answer.
http://forum.xda-developers.com/showthread.php?t=284404
So far i have downloaded
Sprint Cab
dcd_titan_3.2.5.exe
Titan_Radio_ROM_3.42.40.exe
[OliPro MFG 2.40] (Hard SPL)
I'm hoping someone can help me figure this out, whether or not i need to downgrade/upgrade.
And Also was wondering what type of neat things i can do with the roms/kitchen im a total noob at this but trying to make sense of all of this.
Other Phone info:
rom Version 3.35.651.2
radio ver. 3.35.04
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
scrawnyb said:
flash back to a stock (non-GPS if I remember right) ROM from there.
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
You are right on the money.......
that should be the stock bootloader for a stock gps rom.
if you want a custom rom you will need to unlock using 2.40 or 2.47.
kitchens just allow you to cook in apps that you want instead of installing them later. the problem is the install is permanent and they cannot be removed.
i prefer to flash a clean rom and install my apps later.
im pretty sure 2.06 is the temporary bootloader used by no2chem's nueSPL to ram with 2.47. if your bootloader shows 2.06 you will need to flash nueSPL again as it did not flash correctly. 2.07 is nueSPL Relocker.
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
lafester said:
i had not heard of anyone getting "stuck" in 2.06 and the op didn't mention he had tried flashing 2.47 or relocking.
i think you are correct though as i just checked and i am @ 2.07 (relocked).
Click to expand...
Click to collapse
it happened to me, although i didnt get stuck. it was flashed on a card that isnt flashing compatible (telus). i only noticed because it didnt reset itself like it said it should have. returned the card, got a San Disk, and reflashed nueSPL. this time it soft reset itself, and displayed the correct bootloader, 2.47.
I got stuck in 2.06 last night... earlier in the day I dropped my mogul in water and somehow cracked the screen at the same time. After drying everything out for 12 hours the phone came on with barely anything on the screen, I got the phone into bootloader (it was at 2.47) flashed a stock sprint rom, I immediately ran the nueSPL relocker (had to use my mobler to see the screen), after the relocker ran I was stuck in a 2.06 bootloader for some time, eventually I got out of the bootloader (not quite sure how... I flashed the stock sprint rom a few more times and mash some buttons) eventually I was able to run the relocker again and get my phone back to 2.07... a little bit of trouble but it was worth it now that I know I should have absolutely no problems getting a new (probably refurb) phone through TEP
scrawnyb said:
I'm *PRETTY SURE* that's just an updated version of the relocker SPL.
You should be able to flash back to a stock (non-GPS if I remember right) ROM from there.
I think what *MAY* have happened was the process got interrupted when you were unlocking?
so I *BELIEVE* your best bet is to return to stock, and unlock using SPL 2.40, then flashing on the new ROM/Radio
If I'm wrong, I'm sorry; It's early in the morning and I'm not quite awake enough to comprehend everything yet.
Click to expand...
Click to collapse
My phone is stock, i hadnt done anything to it yet. Im just unsure what to do because 2.06 was not shown at the step-by-step instructions.
so let me see if i understand what i need what to do....
flash the current rom, stock 2.06, with [OliPro MFG 2.40] (Hard SPL)
then run dcd_titan_3.2.5.exe and Titan_Radio_ROM_3.42.40.exe
then Sprint Cab??
Thanks for the replys

[Q] Downgrading from SPL 1.16 Hard

Hi,
I have a touch dual running 6.1 which I unlocked but installed the incorrect radio back onto so now it doesn't ring.
After unlocking I upgraded sspl 1.16.exe and now have spl 1.16 hard which won't let me install the radio version I need 1.58.16.27 (this version is running on another phone with the same set up but is locked.)
I have seen with on these pages instructions like run uspl then spl1.15 but these don't seem to work for me. I flashed the rom but still have spl 1.16 hard although I am informed that the device is "Test only not for sale" on boot up.
Is there a sure fire way of downgrading or is there a way of reinstalling the correct radio in spl 1.16.
Am I doing something completely wrong. Thanks for any and all information.
b1968 said:
Hi,
I have a touch dual running 6.1 which I unlocked but installed the incorrect radio back onto so now it doesn't ring.
After unlocking I upgraded sspl 1.16.exe and now have spl 1.16 hard which won't let me install the radio version I need 1.58.16.27 (this version is running on another phone with the same set up but is locked.)
I have seen with on these pages instructions like run uspl then spl1.15 but these don't seem to work for me. I flashed the rom but still have spl 1.16 hard although I am informed that the device is "Test only not for sale" on boot up.
Is there a sure fire way of downgrading or is there a way of reinstalling the correct radio in spl 1.16.
Am I doing something completely wrong. Thanks for any and all information.
Click to expand...
Click to collapse
Don't worry buddy, just flash a rom with a radio, or flash another radio and your device will ring again, for Niki roms with radio take a look HERE
Goodluck,
Worked a charm
Thanks for taking the time.
Ben

Categories

Resources