How to reflash original SPL over SPL2.10.Olipro? - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry

rakdoll said:
Dear All,
Could someone please tell me how to get the SPL back to original. Im planning to sell the phone and it basically needs to be completely as it were.
Thanks a million!
Kind Regards,
Henry
Click to expand...
Click to collapse
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
This guide assumes you already have flashed ROMs and Other components and you are familiar with the process.
NOTE: By downgrading your SPL version your device is more vulnerable to being permenantly bricked if a flash goes wrong, by following this guide through YOU accept responsibility for any problems faced due to this operation. As with other downgrade guides this is NOT intended as a guide for claiming the warranty of the device having flashed components which are not authorised by the manufacturer or carrier.
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )

Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
Click to expand...
Click to collapse
And *that* is the reason we helped you, so that now you help others. One day, rakdoll will help someone else. That is why we are all here. Nicely done!

how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O

revert back
this is what i used to flash mine back to enable original rom to be installed ,so i could take phone back for warrany reasons

Korpse said:
how do I do this without being able to get access to the OS? now that is a challenge, but its what i need to do :O
Click to expand...
Click to collapse
Shouldn't need to access OS. You should be able to do it by putting it in BL mode... THEN plug it into the usb. Then start the updater.

Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way

Korpse said:
Its 2.30.Olipro I need to downgrade from, and you cant overwrite olipro SPL's without using SSPL by des from inside the OS, I'm trying to find another way
Click to expand...
Click to collapse
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.

todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either

Korpse said:
Thanks for the help, but MrVanx's guide uses SSPL by des (launched from inside the OS where I can't get to) to overwrite the 2.10.Olipro to get back to 1.10.Olipro, so that method wont work for me either
Click to expand...
Click to collapse
Oh interesting. A nuance I hadn't picked up on. So, when using the Force using SSPL" option in the flashing utility, you must be able to access the Phone OS? That surprises me, I thought that the RUU utility would put it on the phone even in BL mode and execute it? Hmm... strange. I guess if it is an exe, it needs the OS to run, though. Sort of makes sense. Sorry about the misdirection.

todd_jg said:
2.3 is similar to 2.1.
As MrVanx's guide points out, the key is to get from 2.1 down to Oli 1.1. That will work. His guide works - guarantee it.
Click to expand...
Click to collapse
Hi,
I'm trying to downgrade to the original SPL (I'm trying to get hold of 2.03 but can't seem to find it), so am using 1.06. I've been able to downgrade to Oli1.10 from Oli2.10, but it won't go back to 1.06 from there, after the RUU says successfully completed the SPL is still the same.
Any ideas?
Cheers

downgrade phone for rogers warranty
Hi Guys,
I need to downgrade my phone as well for warranty purposes. Unfortunately Mrvanx's guide is offline at present. Can any one of you give little further detail about what I need to get back to orginal rom/radio/spl and bootloader. Or in shor to be able to send it back for warranty. I do have a new Rogers phone if that can be of any help.
It is from Rogers and currently my boot loader screen says following:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro
Under Device Information:
ROM version: FARIA.R-32
ROM date: 11/06/07
Radio version 1.54.07.00
Protocol Version 32.86u.7020.23H
ExtROM version: BIGSTORAGE
My replacement Rogers Phone has following:
HERM200
IPL-1.01
HERM200
SPL-1.11
Under Device Information:
ROM version: 1.34.631.14
ROM date: 04/17/07
Radio version 1.42.00.00
Protocol Version 32.75.7020.18H
Can anyone please tell me if it is even possible to do this downgrade.
Thanks
B.

why dont you just brick the phone if you are worried about them complaining over the boot loader version. If you cant access the phone i doubt they will be able (or even be bothered) to

Could you please let me know what you did? Did you downgrade To the original Rogers Radio and SPL ? Do you by any chance have all the original Rogers files (WM5, SPL, Radio,...)?
I am with Rogers too and just unlocked SIM (not CID) and installed WM6 (official HTC)
I am wondering how I could lock SIM again if I need to return the phone for Rogers warranty? or unlocking SIM does NOT void the Rogers warranty?
Thanks

Downgrade to SPL 1.11
Hi is anyone able to figure out how to downgrade from SPL 2.10 Olipro to SPL 1.11? I have tried Mr Vanx guide but at the end of the process, I get Error 260. Not sure if I am doing anything wrong.
Do I have to downgrade to SPL1.10 Olipro, before I downgrade to SPL 1.11?
Thanks

I am having some issues downgrading back to an original SPL. I've searched throughout the site and have found a lot of conflicting advice, although this thread seems to be the most relevant.
I started out the process with SPL: 2.10.Olipro
I downgraded to 1.10.oli.
This process was successful in that the bootloader screen now says that the SPL version is 1.10.oli.
Now, when I try to flash the OEM version of SPL, the phone asks the following question:
You would like to run jumpspl.exe
If I say yes, the screen goes gray and says load... but I end up with a 260 error.
I have tried turning off the usb connection in the active sync and starting from the bootloader as mentioned here, but that just ends up giving me a 264 error.
Any suggestions would be appreciated.
Cheers,
~Hat
* edit *
Post #5 from here fixed the issue.
Oszi said:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
Thanks to Walshieau, Todd_jg and Olipro for helping me out with this.
This guide will take you through downgrading the Bootloader (SPL) on your Hermes device
<snip>
The downgrade will take the following steps, since HardSPL does not allow itself to be downgraded directly, nor does SSPL allow versions lower than 1.09 to be flashed.
The first step is to dowgrade to SPLversion 1.10.oli. Firstly download this archive and extract the files to a temporary folder, connect your device up via the USB port and allow it to connect to activesync. Run "RUUWrapper.exe" which will fire up the RUU program:
Select 'Force SSPL' and continue the flashing process as usual.
Allow the flashing process to take place and your device will reboot.
Now check the SPL has been changed by entering bootloader mode, press and hold the side ok and power buttons then insert the stylus into the hole in the bottom of the device. Your SPL version should now read "1.10.oli".
The next step is to download the SPL you wish to finally downgrade to:
SPL 1.04 (includes IPL 1.00)
SPL 1.06 (includes IPL 1.01)
Again extract the contents to a temporary folder and connect your device to activesync via USB. Run "RUUWrapper" in this new folder.
Select the RED OPTION, and TICK THE BOX.
Then flash as normal.
This will flash the final SPL version onto your device.
Verify your SPL version once this has completed by allowing the device to boot into windows Mobile and entering the bootloader as before.
Last Updated ( Sunday, 17 June 2007 )
Click to expand...
Click to collapse

Okay, Im back to 1.10oli, but how do I know if I need to go back to SPL 1.04 (includes IPL 1.00) or SPL 1.06 (includes IPL 1.01)?

OK people, please tell me you have looked at the updated guide right??
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=19&Itemid=27

Yes, but the choices are,
1.04
1.06
1.09
1.11
2.03
and I don't know how to tell which one is stock for my phone. I assume I need 1.04 since my bootloader says IPL-1.00 but I'm not sure because I know that used to say IPL-1.04, and since it appears that that can change for some reason, I want to make sure I get this right so I can get this waranteed. Im going to sell it on ebay and get the new HTC Fuze as soon as AT&T releases it.

Related

Need help stuck in BL

I need help phone stuck in bootloader and its not registering the usb syn cable being attached I think i just need to set it to boot to os. Have HARD-SPL.
ok got usb working again but ruu says it can't find device. is that because its already because its already in bootloader?.
edit- did an info 8 in mtty and got this
Block 0x3A8(936) is BAD block !!!
Block 0x3A9(937) is BAD block !!!
Block 0x3AA(938) is BAD block !!!
EDIT- finally got home and was able to reflash os with sd card and phone works now.
but what did you do to be able to flash?
everytime I try to flash it enters the BL and hangs. Then it says it cannot update. I've got a 1.09 BL
thanks
Read here:
http://forum.xda-developers.com/showthread.php?t=286755
giving more data:
which bootloader version on your device?
1.09
which rom on your device?
1.35.255.2
which RUU are u using?
HTC WWE version
which rom are u trying to flash?
2.11.255.1
Bootloader 1.09 is not compatible with new RUU version inside HTC's 2.11.255.1 ROM.
If you just run the shipped exe file (without unpacking), it will first upgrade your bootloader to 1.11 using the old RUU, then launch the new RUU and flash your rom.
BTW, i suggest you to read the hardSPL thread before attempting to upgrade
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
ok, now that you have HardSPL-1.11 on your device, do this:
1. Use winrar to extract the contents of RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10_108_Ship.exe
2. You will see a file named RUU_Inside.exe
3. Use winrar again to extract the contents of RUU_Inside.exe
4. Run the RUU you'll find here, with device in bootloader mode.
Keep in mind that this will overwrite HARD-Spl with the shipped 1.11 bootloader, if you don't want that, read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeGuide
Well it worked!!! Thanks a lot!!!! any explanation for this? (i forgot to tell I was using vista)
But... eheheh now I found out http://forum.xda-developers.com/showthread.php?t=297849&page=2
and it happens the same.. when I run it... (after winraring the main file) it hangs on the BL! Damn!!!
Muster said:
(i forgot to tell I was using vista)
Click to expand...
Click to collapse
boh!
I know I know awfull mistake!!!
Why does this happens when I try to update? ANd why it worked the way you said it would?
Muster said:
Ok, now I noticed that incompatibilty and used HArd SPL to upgrade to 1.11.
that's what it says now in threecolor bootloader.
But still when I try to upgrade it hangs on the bootloader saying HERM200 IPL-1.01 and HERM200 SPL-1.11 and USB in the white area. And in the PC it says OS information detecttion for ever!!
If I reboot it no problem, everything is working.
thanks for you help!!
Click to expand...
Click to collapse
uhh... it should say SPL-1.11.Oli
It did not!! It says now 1.11!!
when I tried the upgrade to WM6 it used it's own bootloader 1.09 Ds and it changed again. Is it possible that 1.09 BL is definitevely not working in my TyTN?

My Downgrade plan. Looking for input from the pros

What I have now:
OS: Black 2.0 Cingular edition
Boot Loader: 1.01
Radio BL: 108
Radio: 1.38.10
what I want:
OS: WM 5 from the 1.34 cingular release
Boot Loader: Loader from the 1.34 cingular release
Radio BL: AFAIK you can't downgrade these so staying at 108
Radio: 1.16.00.00
How I plan to get there:
take the .nbh form the 1.34 cingular package and use RUU to flash the device.
Questions and concersion:
I'm looking for input on possible incompatabilities and hang-ups with varios BL versions and what not.
comments / feedback on my plan would be greatly appreciated and I will build a monument in your name if you help .
This has been covered before...
But, since you're well on your way to brick-ville, I'll buy your phone off you for, say, $100? It'll be worth less after you brick it...
Read up on the W*I*K*I and Oli's 1.40.Olipro bootloader before you do something dumb.
I did read it.
And thats the plan I came up with.
I was looking more for a confirmation.
The wiki has a ton of great info but its laid out reall crappy and not very cohesive. So I figured I'd post what I've came up with after reading it to see if I missed something. And from there maybe get more specific input on where the issues/dependencies are..... or maybe not.
spicer said:
I did read it.
And thats the plan I came up with.
I was looking more for a confirmation.
The wiki has a ton of great info but its laid out reall crappy and not very cohesive. So I figured I'd post what I've came up with after reading it to see if I missed something. And from there maybe get more specific input on where the issues/dependencies are..... or maybe not.
Click to expand...
Click to collapse
From your plan it is obvious that, even IF you read the wiki, you didn't understand it. Re-read the THREADS about 1.40 SPL and also search for MRVANX and read his TUTORIALS...
---New plan
What I have now:
OS: Black 2.0 Cingular edition
Boot Loader: 1.01
Radio BL: 108
Radio: 1.38.10
what I want:
OS: WM 5 from the 1.34 cingular release
Boot Loader: Loader from the 1.34 cingular release
Radio BL: AFAIK you can't downgrade these so staying at 108
Radio: 1.16.00.00
How I plan to get there:
Flash to hardSPL-v6
Fash Radio to 1.16
flash OS i get out of the 1.134 package. (the os.nb file i believe it is named)
last flash the boot loader.
Questions and concersion:
I'm looking for input on possible incompatabilities and hang-ups with varios BL versions and what not.
comments / feedback on my plan would be greatly appreciated and I will build a monument in your name if you help .
LegolasTheElf said:
From your plan it is obvious that, even IF you read the wiki, you didn't understand it. Re-read the THREADS about 1.40 SPL and also search for MRVANX and read his TUTORIALS...
Click to expand...
Click to collapse
I really appreciate the feedback. At least you're letting me know my plan wont work. Which will prevent me from trying it. But it would be kick ass if you could be more specific about what in the wiki i missed like :
-you can't flash the entire .nbh file cause it will try to replace your boot load and break it.
or
- Re-read the THREADS about 1.40 SPL because *something useful here*
Either way I'm still thankful cause I know my plan is a **** sandwich.
Very good.. You're getting there! It's nice to see someone read some directions..
You have it mostly right.. Flash the HardSPLv6 first. Then, grab the .nbh from the cingular rom and combine it with CustomRUU. Choose 'Autodetect' (we're looking for a hard-spl flash)..
Then, once that's done, you'll have the right radio, OS, splash, etc.. The only thing left would be to down-grade the bootloader, which I would advise against.. But, you can do it.. There is a seperate thread on HOW to do that, as it isn't just a one-step process.. Search and ye shall find.
Thank MAn!!! That kicks ass.
I need to send my phone back because the radio dies every 5 mintes.
So I want to get it as close to factory as possible.
So after I downgrade the BL i won't be doing anymore flashing to that phone.
Sometimes when I soft reset the phone is says "No GSM" even when sim is there. Soft reset it again and the radio is detected.
Very irritating.
Check out:
http://www.mrvanx.org/hermes_guide/
Flash HardSPL-1.40
Create NBH containing your provider's 2xSplashScreen + ExtROM + OS & flash it
Flash 1.16 radio
Flash-HardSPL-1.10
Flash your original IPL & SPL versions.
F-ya! That last part about down grading the BL is the part I was having trouble pinning down.
One last question:
Can I use the cingular NBH or will it try to flash the RBL and crash because you can't down grade the RBL
the the new mrvanx page is dope. found the donwgrade guide.
Bricked using this method
pof said:
Flash HardSPL-1.40
Create NBH containing your provider's 2xSplashScreen + ExtROM + OS & flash it
Flash 1.16 radio
Flash-HardSPL-1.10
Flash your original IPL & SPL versions.
Click to expand...
Click to collapse
Pof,
I did it this way but after flashing the radio rom I get no GSM and then I'm stuck in the Windows Mobile Screen.
I have looked in the Wiki but how can I actually unbrick?
My SPL is still 1.40 Oli. But I can't get activesync to work.
Should I flash the new radio via SD card or any other way (mtty?)
I would be very gratefull for any help,
Cheers,
HJ
P.S. Found a solution; http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
I will try to do this trick.
Thanks
@hellejoep: Try flashing your latest working radio again in NBH format.
pof said:
@hellejoep: Try flashing your latest working radio again in NBH format.
Click to expand...
Click to collapse
Pof,
One question, Can I upgrade radio rom via mtty?
Or otherwise?
Cheers,
HJ
P.S. How can I Flash any radio in NBH format? While stuck in bootloader?
hellejoep said:
Can I upgrade radio rom via mtty?
Click to expand...
Click to collapse
no
hellejoep said:
How can I Flash any radio in NBH format? While stuck in bootloader?
Click to expand...
Click to collapse
Disable activesync, and use CustomRUU.
pof said:
Disable activesync, and use CustomRUU.
Click to expand...
Click to collapse
Done that but then I get a Error 260.....
Any suggestions?
Or is there a way to bypass this? I have IPL 1.01 and SPL 1.40 Olipro.
I now got a Connection Error 264 but the bootloader gives usb and I can reach the hermes bij MTTY.exe.....
What is going wrong?
@hellejoep: close all programs including mtty before u run ruuwraper. Make sure you're using the latest version (v4.2) and activesync is not enabled.
pof said:
@hellejoep: close all programs including mtty before u run ruuwraper. Make sure you're using the latest version (v4.2) and activesync is not enabled.
Click to expand...
Click to collapse
It worked, cheers!!!!!
LegolasTheElf said:
Very good.. You're getting there! It's nice to see someone read some directions..
You have it mostly right.. Flash the HardSPLv6 first. Then, grab the .nbh from the cingular rom and combine it with CustomRUU. Choose 'Autodetect' (we're looking for a hard-spl flash)..
Then, once that's done, you'll have the right radio, OS, splash, etc.. The only thing left would be to down-grade the bootloader, which I would advise against.. But, you can do it.. There is a seperate thread on HOW to do that, as it isn't just a one-step process.. Search and ye shall find.
Click to expand...
Click to collapse
@LegolasTheElf,
This was great example on how to get people to read the wiki. I like your approach and I will try to use it in the future.

Downgrade to original SPL 1.04

HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click on the mrvanx guide at the bottom of my signature, it will tell you how to downgrade in the guides.
mysharif said:
HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click to expand...
Click to collapse
I have been there mrvanx guide. but he don't have the solution to this problem. Just to downgrade the rom to wm5 not the SPL.
mysharif i think we have to shout again.
Help us anybody there we are stuck here.
OK guys the SPL downgrade can be done by downgrading to SPL 1.10.oli then flash any ROM with SPL 1.04 in it.
The only reason i can see that you wish to downgrade to 1.04 is because of a warranty issue. What is the problem with your devices??
You are great. I hope it will work for my Imate JasJam. Last night I was flashing my ROM with the original ROM but modified with NBH decomplie too by dutty. Before that I wrecked my device as I used the flashing of ROM using the latest sensation of loading the SSPL to RAM by des. That was my mistake that I used the original ROM. Then I removed the USB cable as it was taking too much time and because of danger to my imate I did that. Anyhow I got the NO GSM error but then I ran the Dutty's WM6v2 cooked ROM and it fixes all the things I am using it now.
The reason for my Imate JasJam degrade is my jog is not working according to its function. You know jumping from field to field. I didn't found any of that problem solution till the page of 30 in threads and posts. I am searching but if anybody knows the link. Kindly help me. So that I will save a trip to see the warranty people. (here we don't have ladies receptionists )
Sorry for the stupid question, how do I downgrade from Oli 2.10 to Oli 1.10
Il write a guide on it...too many PMs about this.
mysharif said:
HELP HELP
Hi All ..i'm totally lost here. I've tried to look for guideline to downgrade to original SPL 1.04 but i cudn't find any.I installed the latest m3100 unlock software v3a doing so my SPL is now version 1.4 Olipro. For warranty purposes how do I downgrade back to 1.04? I'm sorry this problem might have been addressed somewhere on the forum..if so cud someone provide the link to the thread on this. thank you so much.
Click to expand...
Click to collapse
I have the same problem. My touchscreen is dud and Softbank is very anal about the bootloader and warranty. im stuck with Olipro 2.10 and tried flashing the latest softbank rom. When i try via USB/Windows it gives me error 260.
Flashing with MicroSD works, but after a few attempts, its still Olipro bootloader...any ideas?
aquasesh said:
I have the same problem. My touchscreen is dud and Softbank is very anal about the bootloader and warranty. im stuck with Olipro 2.10 and tried flashing the latest softbank rom. When i try via USB/Windows it gives me error 260.
Flashing with MicroSD works, but after a few attempts, its still Olipro bootloader...any ideas?
Click to expand...
Click to collapse
Ofcourse...because flashing an original RUU it doesnt recognise the new bootloader (Hence your 260 error), and HArdSPL doesnt allow itself to be overwritten by a retail RUU. IF you read through the HArdSPL threads you would know this.
mrvanx said:
OK guys the SPL downgrade can be done by downgrading to SPL 1.10.oli then flash any ROM with SPL 1.04 in it.
The only reason i can see that you wish to downgrade to 1.04 is because of a warranty issue. What is the problem with your devices??
Click to expand...
Click to collapse
Hmmm, just yesterday (Thursday) I was asked by a VP at our company if that could be done. I was reluctant to say yes, but mrvanx comes thru with a fix.
The VP is in fact worried about having to return some devices to Vodafone, and he want to make them look "original" when they go back.
GreatGrey said:
Hmmm, just yesterday (Thursday) I was asked by a VP at our company if that could be done. I was reluctant to say yes, but mrvanx comes thru with a fix.
The VP is in fact worried about having to return some devices to Vodafone, and he want to make them look "original" when they go back.
Click to expand...
Click to collapse
Just flash SPL 1.10.oli.......................then flash a vodaphone ROM, dont use 'force SSPL', just use autodetect.
well to get spl 1.04 all u have to do is take rom koch and the wm5 rom u are downgrading to. first downgrade os. then take that rom and using rom koch split it into parts and just take the spl and make it into a nbh and use the custom ruu on here. select force sspl and itll make ur spl 1.04. this is a quick guide and do this at own risk. using this method i got my first 8525 to aku 3.5 att and original spl. if marvanx comfirms i didnt make any mistakes i can make a new thread with pics and all so we cna add this to resources and stop the questions.
Pawel062 said:
well to get spl 1.04 all u have to do is take rom koch and the wm5 rom u are downgrading to. first downgrade os. then take that rom and using rom koch split it into parts and just take the spl and make it into a nbh and use the custom ruu on here. select force sspl and itll make ur spl 1.04. this is a quick guide and do this at own risk. using this method i got my first 8525 to aku 3.5 att and original spl. if marvanx comfirms i didnt make any mistakes i can make a new thread with pics and all so we cna add this to resources and stop the questions.
Click to expand...
Click to collapse
Or you could just wait until my guide is finished??
You dont need to use the rom koch ... duttys nbh tool is far more appropriate for this since we aint doing any cooking.
yea your right I just wanted to reduce your work load.
mrvanx said:
Or you could just wait until my guide is finished??
You dont need to use the rom koch ... duttys nbh tool is far more appropriate for this since we aint doing any cooking.
Click to expand...
Click to collapse
Hi mrvanx, some input to go into your guide (in case you havent come across this yet).
While flashing 1.10Oli under Vista, users may run into a problem where after loading SSPL and the phone goes into (SSPL) bootloader mode, the RUU program cannot detect the phone and returns an error.
This is due to the Vista drivers for HTC USB Sync. The driver needs to be manually "updated" just like in your Vista flashing guide. In this case, while the phone is in SSPL bootloader mode, go into device manager, replace the default HTC USB Sync driver with the USBAS one from your Vista flashing guide.
Then soft reset the phone, and try again. Worked for me.
For some reason, SSPL bootloader may appear as a different device to Windows than the hard/standard bootloader, so even if the Vista procedure has been performed before, it looks like it needs to be done also for SSPL.

Begging a small tip...because of No GSM...thanks very much!!!

My Hermes is still showing No GSM. Please inform me if I got something wrong.
I have tried to upgrade the radio rom from SPL-1.40:
http://forum.xda-developers.com/showpost.php?p=1321011&postcount=1337
That's wrong because HERM_Radinly_1.41.00.10_CustomRUU should be upgrade from SPL-1.04, right?
Because I have stuck on the tricolor screen, so I need to re-upgrade from HERM_Radinly_1.41.00.10_CustomRUU with the same choice of bootloader, right?
And then, I have succesfully upgraded to 1.41.00.10, but also showing No GSM, and the SPL is upgraded to 2.10 olipro after by using HardSPL V7.
And I can see "Upgrade instructions
Just download and execute these to upgrade; however it is recommended that users install HardSPL before flashing these radios.
" in http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms, then...I thought that I have doing right to upgrade the radio rom to 1.43.00.00.
Yes, I have upgraded to 1.43.00.00, but my Hermes is still showing No GSM. So I found from wiki, I found http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick, in the first line of the table, yes, I can boot the OS and no GSM, so I flash Hard SPL and update the rom from 1.43.00.00 to 1.40.30.00, but it showing No GSM also.
Then, I tried 1.07.03.10, no GSM also.
After that, I found I have missed a important sentance, "You can now do radio only upgrades in Bootloaders other than SPL 1.04.". Then, I try to found how can I downgrade SPL from 2.10 to 1.04. Thanks for Martinhdk and shogunmark, http://forum.xda-developers.com/showthread.php?p=1330247#post1330247.
down to 1.10 by choosing bootloader, not success....
after use Force by SSPL, success!!
and then down to 1.04 by choosing bootloader, not success....
first time not success when using SSPL....
second time also....
down to 1.04 by chooing bootloader again....not success
down to 1.04 by chooing bootloader and Hard-SPL....success!!!
Now...not HardSPL anymore!!!!
Then, I downgraded SPL to 1.04 successfully, checked by mtty also. Then, I can start to fix No GSM finally.
And then upgrade to 1.40.30.00 by method of RUU
but I can remember that, Upgrade instructions
Just download and execute these to upgrade; however it is recommended that users install HardSPL before flashing these radios.
install HardSPL V7, and then now is SPL-2.10.Olipro
After that, run HERM_Radinly_1.40.30.00_CustomRUU, choosing SSPL or bootloader version, failured sever times
When choosing the HardSPL and bootloader version SPL-2.10 in the second time....success!! But it is still showing No GSM.....
and... the PPC always cannot detect the USB connection....
What shoud I do now?
Do I made a big confuse on the concept of upgrading?
Please give me a small tip.....I really read many and many threads but....
I just want to use my PPC normally.....
I can see that you have certainly been searching the forums so hopefully others more knowldegable than me will help - rather than tell you to look even more as they so often do here on this site when the problem is simply inexperience for most of us.
In the meantime have you tried following the "No GSM" instructions on the Hermes Wiki here: http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5? It looks like this will need even more reading but hopefully it will help. I am afraid I am not familiar with this procedure but others should be able to offer support.
I must admit I thought HardSPL was OK for all radio upgrades - but perhaps you have read more than me.
Good luck

phone is stuck at htc screen and it says no radio

i installed the wrong rom on the wrong hard spl. i had the hard spl a 1.30 installed and dcd 3.2.0. now the screen is stuck at the loading screen that says htc smart mobility. and no radio at the bottom. please help and the phone wont sync.
Good luck on that.. You installed a bootloader for a different model -- likely the TyTn or Trinity. What phone do you have? What instructions did you follow?
If you do have a Titan, then possibly via the SD Card you can change the bootloader to the new 2.47 (I haven't played with it yet but another may provide a solution). You are likely out of luck in flashing to any of the other Titan bootloaders as you must be able to boot into the OS, but with you error of installing an inappropriate bootloader you are out of luck there.
no it was a bootloader 1.30 for the titan
Your information is incoherent.
What rom/bootloader did you have prior to updating?
What rom/bootloader did you try to upgrade to?
You need a minimum SPL of 2.40 to install DCD 3.2.0
I use 2.47 from no2chem and it works great. http://forum.ppcgeeks.com/showthread.php?t=30561
Are you able to boot up the device? If so copy the SPL 2.47 to the card then to the PDA and run it from there.
If not, put the PDA into Bootloader mode and try to install Olipro 2.40
http://www.lifesnotsogood.com/dcd1182/titan/spl/titan_SPL_2.40-olipro.exe
Failing that you can try to flash back to an official ROM if you have one.
You need to soft reset your phone while holding the Camera and power buttons. This will force your phone in to the bootloader. You should then be able to reflash to lower ROM. Then you need to search for Olipro or whatever the 2.40 bootloader is. Your best bet after that is to flash the official Sprint 3.35 Radio and Rom then flash to DCD's.
**Edited**
Sorry Hamilton didn't realize you gave a link to the 2.40 bootloader.
If he is sure that it is "bootloader 1.30 for the titan" then I know of NO such bootloader. He has likely installed the wrong bootloader (for another device) and therefore no amount of flashing to an OS ROM will help him boot into the OS. Unless via an SD card for 2.47, beastmode216 is stuck with a borked device.
So, beastmode216, I'll ask again, where did you get such instructions and where did you source your bootloader 1.30?
What is one of the earlier bootloaders? I was thinking my Mogul orginally had something like 1.30 or 1.40.
thanks guys but the problem is solved. just make the phone go in to the bootloader
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
calash said:
Verizon stock bootloader is 1.30 if I remember correctly. It has been several months since I have seen a stock bootloader
Click to expand...
Click to collapse
My mistake, as pointed out by gc14 the stock bootloader is 1.04.
Ahh, ok, my fault as I thought that he had also installed a bootloader under the name of 1.30.. That could've been an unlocker for a TyTn or another device.
Correct, OEM bootloader should be 1.30.60.
Click to expand...
Click to collapse
This is incorrect. The stock bootloader is 1.04. The stock radio is 1.30.60.
SPL 1.30 does NOT exist for the Titan.
Stickies exist for a reason...to read them as they contain valid, useful information. http://forum.xda-developers.com/showthread.php?t=392133

Categories

Resources