Related
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
i have the same problem with my x10 but i have warranty but whilst i was waiting for them to collect it, i cut my usb lead up and stripped the black and red cables back obviously positive and negative and took the battery out and wedged each cable on the phone connector with the battery my battery had a plus and negative signs on it so was easy 2 work out, it charges the battery but it doesnt come up as charging on the phone it will still blind red lights but doesnt turn off, you have to keep and eye on the charging levels on the phone status do not let it go over 99% as this method dont tell the battery to stop charging, also this is not full proof and could break your x10 if not dont correctly,but as for your question the usb port does need to be soldered good luck
j0hn0n1 said:
I know this isn't a new topic and I've read lot's of posts about similar problems, with various causes and fixes, but my x10i isn't charging at all. Neither through the wall charger or through the usb. When I look into the charging port I can see that one of the little metal pins is bent right up, so I've decided to try and replace the charging block.
I got a charging block off ebay, but I'm no expert when it comes to soldering & electronics, but since the phone is dead anyway I have nothing to loose.
As far as I can tell when I look at the original one, there doesn't seem to be any signs of soldering in the first place, although the connections are all so tiny that it's hard to tell.
So am I right in thinking that the charging block doesn't need to be soldered at all, and could I get away with just gluing it to the board, and if so what would be a suitable glue for this kind of purpose.
Thanks ...John...
Click to expand...
Click to collapse
Hi John,
I fixed my friends USB port, you will need:
"helping hands" (a tool for holding small things with a magnifying glass)
0.5mm or 1mm Soldering iron
Hot glue
Under the magnifying glass, there you will see the 5 pins the usb port was solderded onto. You will need to put a little bit of solder onto each pin and onto the board.
Hold everything together with the helping hands, and just tick the soldering blobs with your iron. This will connect all the points. Do not solder for to long, or you will bridge pins or remove the solder.
Continue until all 5 is connected. Solder the 2 points on the side (holds the USB port, you could do this first if you don't have the helping hands)
plug in cable, use multimeter to see if there is current by you battery pins.
Voila.
If no power then you have to follow one of those fixes online where you have to bridge the doide and the V+ port.
Thanks for the info, like I said the phone is dead anyway, so I can't really make it any worse (That's what I keep telling myself anyway).
It the parts were a lot bigger, I probably wouldn't be bothered as much, but if I do get it wrong, I'm hoping I can take it off, remove the solder and just start again. (hopefully)
I think I have a good idea now of what I'm supposed to be doing, but I'll probably have to wait till I get a new soldering iron, as mine is a little bit too big.
Thanks ...John...
Hello All,
All of a sudden, the plug wasnt connecting into the port like it always did and after i looked online, I seen that it happened quite a few times to others. It simply will not charge now. its been dead for a week and iv been contemplating what to do so i figured is take it here before i make the final decision. If anyone could give me some advice I greatly appreciate it.
It seems there are a few options, call viewsonic and try to get them to semd me a new one since I got it in Feb but im rooted so thats out, plus I dont want the hassle. Take it apart and try to re-soder(sp) it back on to the mother board- although I hear it is somewhat easy, but I could never do it.
SO my last possible option from what iv read online, is to buy the Malata Zpad/Gtab dock. From how I understand it, I will set my gtab in the dock and it will charge, but I have a few questions/issues with that.
1) I heard it doesnt come with a power cord. Is this true? Do i need to use the cord that my gtab came with and will it work to power this dock?
2) If this dock will indeed charge my gtab, and fully fix my issue, where is the best place to buy it/fastest shipping? The only ones Ive found are around $50 with free shipping(which im good with), are shipping from China and take up to a month to finally receive.
Again I have not been able to charge my gtab for a week, and need to find an alternative way, due to a faulty Ac port, which iv found many others online have the same issues.
please community, any would be a huge help. thank you all for taking the time.
bump
Any replies would be very helpful, thanks
The charger that comes with your gTablet works with the dock. The dock doesn't come with a charging cable. Just switch the cable to the dock and you're good to go. It'll start charging as soon as you dock it.
About two weeks ago, electroniccrap.com had them in stock. Yes, it's around $50. I actually got mine through them (ordered via Amazon). It was sent priority mail, so it arrived in less than a week.
I had the same problem and I open the tablet and soldered the AC port again back to the board. And it has been working fine for the last couple of months.
Re-soldering the connector shouldn't be a problem for an experienced person with decent tools. Ask around among your friends, neighbors, acquaintances -- surely someone can do it.
You might stop in at some local computer stores that do in-store repairs -- look for a technician with gray (or very little) hair, he'll probably be excited about the prospect of actually using his old soldering iron again, just like 'back in the day'!
Right after I got my G Tab, it fell off the desk and broke the charge socket in the unit. I figured out how to open the unit up and found the metal strap had been pulled lose and also the solder connections [I think there were four (4) had been pulled lose. The metal strap wouldn't hold the socket down on the board so I bought a tube of the new Locktie GEL Super Glue. I carefully added some drops of that to hold it to the board while I did the solder job. It has worked fine now for over a year thanks to the super gel glue.
We have tile floors in our home and shortly after fixing the socket, I again dropped it from about waist high, the thing bounced back up and I caught it in mid air. Other than a little scratch where it hit the tile the tablet has worked just fine. TRY THAT WITH AN IPAD AND SEE WHAT HAPPENS. These G Tabs are really rugged as the above demonstrates. It was also interesting to see the inside of the unit. Looks pretty simple. Hope this helps you repair yours.
Oh! another imprtant thing to remember. Before you start to pop the back off, on each corner there are little plug covers, when you pop those out there are Four (4) screws at each corner. Make that your first step to remove them first.
Anyone else have this issue. The usb cable comes apart on the asus end(see pic)
P.s. this has never been abused and was treated with the the greatest of care
http://imgur.com/AOPWP
Nope, maybe try a tiny dab of superglue?
Well I know it is an easy fix I just thought it was kinda weird and wanted to know if I was the only one who had this problem
Yup happened to me. But on the other side. The USB side. Cant sseem to attach the pic from my tfp
i had this happen to me right out of the box! plugged the device in to charge then unplug after full charge then this happened.
susko said:
Anyone else have this issue. The usb cable comes apart on the asus end(see pic)
P.s. this has never been abused and was treated with the the greatest of care
http://imgur.com/AOPWP
Click to expand...
Click to collapse
Yes! It's a piece of crap! And I tried to RMA to Asus but they want the bad one back and then they'll send out a new or fixed one. So how is a person supposed to charge the tablet with no power cord? Very disappointing, Asus! They've sent me several follow up surveys to the phone calls and emails and I've told them how I feel about this. They don't seem to respond after that... Haha! Oh, well. The superglue route is probably the best way to go, anyhow.
My cable came apart like that the first time I used it. I carefully removed it from the connector on my tablet so as not to damage any wires, and then pushed the cap back on until it clicked and it hasn't come off since.
I think the problem is that the black cap isn't properly seated over the connector on some charging cables so the little clips on the inside never engaged. I have a half dozen chargers for the TF Prime and 3 were like this.
This is definitely something that might scare you the first time you try to unplug your connector, but it isn't a huge problem unless you rip out the wires or something.
My wife's did this the first time we unplugged it. I used a few drops of super glue on it and it has never come apart again. Mine on the other hand never had the issue. I think there was a batch of the plugs that they never put the glue on them so they weren't sealed when they got shipped. Put a few drops of glue on it and seal it up and enjoy the full use of the USB plug
Sent from my Transformer Prime TF201 using xda premium
Before I begin, if there is already a thread outlining this particular problem, I apologize in advance.
Yesterday my Truesmart was in the charging cradle sitting on my desk, not realizing it, I accidentally opened a draw which pulled on the USB cable, dragging my Truesmart off of the desk and onto the floor. My truesmart fell about 2 feet and is fine, but the charging cradle will no longer charge it. I would assume that something broke in the cradle when it fell, which justifies the pathetic quality of it, although there is no visual damage on the cradle and when shaken nothing rattles around inside of the cradle.
My question is what should I do now? I am almost certain that it is the cradle that is the problem and not the Truesmart or the USB as the watch will still turn on and the USB will charge other devices. I have tried different power sources and different USBs and I only have one cradle. Is there anything I should troubleshoot in order to try and get the cradle working? Or is is possible that the problem is with the watch?
Any assistance would be greatly appreciated.
The spring contacts in the cradle may have gotten smushed in a bit by the impact. Try prying them up gently with like a needle.
Otherwise, the solders connecting the microUSB connector inside the cradle might have failed. They have been reported to be of poor quality on another owner's cradle with cold solders. Try resoldering them if probing them shows them not good connections anymore.
Thirdly, maybe your USB cable itself was damaged in the drop. Test it too.
Sent from my Nexus 5 using Tapatalk
I tried what you suggested with the needle and it didn't make any difference, they seem to be at the right position anyway.
I have a feeling it might be the solders, as it is possible that the sudden shock of the microUSB inside of the port caused something to break. Unfortunately I do not have any knowledge of soldering nor the equipment to do it. I wouldn't know how to open up the cradle without breaking it anyway.
I already tested the USB cable, it charges anything else, and I have tried other USBs with the Truesmart to make sure that it is infact the cradle.
I have sent Magan (may or may not have spelt her name right) two emails and have received no response.
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
I've been thinking of replacing the spring contacts with actual pogo pins. It's silly that the charger doesn't utilize them to begin with.
Sent from my GT-N5110 using Tapatalk
rhineymac said:
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
Click to expand...
Click to collapse
I am aware but I figured it was worth a shot since my order was missing a keychain that I was told would ship "soon".
I might look into taking it into a shop, how much did it cost you to do that? And I didn't understand your last sentence.
He mistyped "dollar store".
Apparently they have such cheap budget shops up in Canada too. I get my colored USB cables from them, they say, " Made in China" on them and generally last a couple of weeks.
Sent from my Nexus 5 using Tapatalk
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
rhineymac said:
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
Click to expand...
Click to collapse
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
SkyHawkTech said:
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Click to expand...
Click to collapse
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Agent. said:
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Click to expand...
Click to collapse
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
rhineymac said:
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
Click to expand...
Click to collapse
I'm pretty sure mine is the female USB port too, as my watch was plugged in when it fell so I assume the shock of the male USB caused it to break. Your guess is as good as mine as to if they ever plan on actually fulfilling their promises, they have done a pretty crummy job thus far. The charger is absolute junk, at least if we had the charging cable they initially promised we might be able to work with it a bit more.
trent999 said:
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
That isn't a bad idea for a temporary fix but the fact that it even comes down to doing something like that is absurd in my opinion, the charger should have been done and ready while they were dealing with all of the other BS issues.
Well, remember that for most owners the charging cradle they received works fine. It is not that poorly designed - mostly failures reported have been due to shoddy assembly. Similarly careless assembly has been reported on the watch itself in various areas.
I got my extra charger I ordered via Kickstarter, included in the package, but have never tested it nor needed to. I also figured out a way to charge the spare battery with an Anker universal charger, just in case. That charger came free with a couple of VGNexus batteries I bought from Amazon.
You might have better luck with the USB port repair staying fixed if you support its attachment to the board, such as it is, with an application of SuperGlue prior to resoldering the connections.
Holding a cable connector in place via only the contact solders would always be a bad design though.
Sent from my Nexus 7 using Tapatalk
Hi All,
I have a Nokia 7.1 that stopped charging. I cleaned out the charge port and tried different cables and adapters but nothing worked. I've since come to find out that it's a common enough problem that lots of people post about it on Nokia's support forum with no other option other than taking it to a service center. I'm in the USA and there's not a single service center in my state so I decided to try and replace the daughter board myself. I've done this kind of thing before on other phones, my Nexus 4 was a frankenstein's monster by the time I was done with it.
My problem is I can't find a reliable source for a quality part. There's tons of replacements on amazon, ebay, aliexpress and other random sites but all the ones I've read had issues for connectivity of cell service or wifi. Does anyone know where I can source a new daughter board for this phone?
Any help is greatly appreciated.
Thanks!!
I went through the same issue.
Bought another type c charging port on Amazon, it still works.
Awesome! Thanks for the reply. Did you go with one of the ~$10 ones or one of the ~$20 ones?
My 7.1 developed the same problem. What is the root cause? Is it mechanical problem of the connector pins worn out/oxidized? It does seem to be a mechanical problem since I can still wiggle the cable to make it charge for a while. What puzzles me is that the USB-C has inherent redundancy with 4 power and 4 ground pins that it should not easily fail. I have a phone with the old micro-USB and the charging still works flawlessly.
lejaune said:
My 7.1 developed the same problem. What is the root cause? Is it mechanical problem of the connector pins worn out/oxidized? It does seem to be a mechanical problem since I can still wiggle the cable to make it charge for a while. What puzzles me is that the USB-C has inherent redundancy with 4 power and 4 ground pins that it should not easily fail. I have a phone with the old micro-USB and the charging still works flawlessly.
Click to expand...
Click to collapse
I'm not sure. It does seem to be a mechanical problem, but I've seen some repair videos where they open it up and just run a soldering iron over the connector pins on the board and it starts working again. I've ordered a daughter board and a replacement back glass panel in case I break it trying to get it off. I'll update after I get the parts and open it up to see if it works.
The board I ordered was this one from Amazon Smile:
https://smile.amazon.com/gp/product/B08166DLDC/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
It seems like the ~$10 boards are missing some chips that the ~$20 ones have, at least according to the pictures that were uploaded with the listing.
@bpowdhar, Thanks for the quick reply. I did order a connector board on Ebay, and it looks to be of the ~$10 variety. I'll see how it works when it gets here. I will also try the "melting the solder" trick without removing the connector first. If that works, I'll leave the old board in place just to minimize the risk.
So I received the USB-C charging board and replaced the bad one. Now, it seems to be charging normally. It took some work to open the back cover by heating to soften the glue/tape around the edge. I then used an a xacto knife to pry the corner open followed by dragging an old credit card to slowly separate the cover. Once it's open, everything went smoothly. Just watch one of several Youtube video clips to know what to expect. You do need a small Philips screwdriver and a #5 Torx driver. You need to lift a ribbon cable and a micro coax cable from the board. Just don't forget to put them back on to the new board. I didn't bother to fix the old board by re-solder the connector pins because they are way too small for my solder iron.
I rely on the existing glue/tape to glue the cover back, but I'm sure it's not as water/dust proof as before, so I may redo that part to clean the old tape out and use the new tape or glue when I have more time.
I do noticed a couple of parts missing on my $9 board. I don't know if they have anything to do with regulating the high voltage fast charging. I usually charge the phone with a 5V adapter, and I will stick to 5V, at least for now.
Thanks for the update! I'm still waiting for my board to arrive from Amazon. It was delayed with the new shipping date anywhere from Nov 5 - Nov 10 and it still hasn't arrived. It sucks because tracking info shows that it arrived at my area's sorting facility on Oct 29 and left it on Nov 4. So it should have only taken a day or two to get to my local post office and to my house. I'll update when it finally gets here.
I know it's been a couple of months, but I finally got the part and swapped it out yesterday. The battery was completely dead so I plugged it in to charge and left for the day. I came back to it this morning and it's at 100% battery! I'm so happy now! I've attached a couple of pictures showing the old board (with the red dot) and the new one. So far no connectivity issues, but I'll give it a couple of weeks to see if anything changes.
A couple other notes:
It was surprisingly easy to get the back glass off. I used a heat gun on low and ran it around the perimeter for a couple of minutes and a utility knife to cut the adhesive. This part was what I was most apprehensive about tackling.
The fingerprint sensor comes off the same way, apply heat and press / pry away from the glass to reuse.
If I had to do it again, I'd buy the tube of sealant. The replacement glass came with a set of narrow adhesive strips and those were a pain to deal with.
Thanks to everyone who contributed to the thread. Hopefully this helps someone else.