Connection problem - MDA, XDA, 1010 General

I have a Wallaby that i bought on an auction, but i haven't got any CD with drivers so when I connect a Wallaby through USB to my PC, it says Unknown device. I can't find drivers for it anywhere.
Can you help me where I can download drivers or what to do to make it work?

You just need the ActiveSync tool, that can be downloaded directly from Microsoft....
Stefan

Moderators are working with the same

Related

activesync needs drivers to recognize my wallaby 2003se

i got 2003se on but my computer with activesync 3.8 on winxp will not recognize the cradle or the phone ---drivers for the tmobile 2003 edition maybe?Who knows?active sync doesn't work now and i'm goin craaaazy!i don't want to trade os's cause' 2003se seems really cool!help!
You shouldnt need a driver. When you connect with usb you should get "hardware found" once this completes it should say "hardware ready". If you then install activesync and usb is enabled in activesync settings, it should be discovered and you will be prompted for a name for the device. Have you tried activesync 4.?
cruisin-thru said:
You shouldnt need a driver. When you connect with usb you should get "hardware found" once this completes it should say "hardware ready". If you then install activesync and usb is enabled in activesync settings, it should be discovered and you will be prompted for a name for the device. Have you tried activesync 4.?
Click to expand...
Click to collapse
i finally got it to work again!thanx!!!I'm gonna get a new sim card now so I'll be up n runnin!I hope?

Help me find software/drivers for my QTek 1010

I have bought a Wallaby QTek 1010, but without a drivers/software CD. Please help me: what do I need to install on my pc, to connect to my Wallaby (what software? what drivers?) And where can I download it?
(I did have searched the internet, but couldn't find enything )
1.) ActiveSync
2.) directly from Microsoft for free
Stefan
Thanx! ...off to try it out!
software
Hi i have a 1010 and have upgraded to w2003 from LumpiStefans rom kitchen, hasn't missed abeat since, so you may want to flash your rom and update.
Peace
Just downloaded ActiveSync on the Evil Empire's site, plugged the USB cord directly to my Qtek 1010 and the other end to the PC's USB port, still can't detect it!?
Bad cord?
Do I need the cradle?
I only have the unit and the charger, that's it.
HELP!
Are you using the correct USB-Cable?
Is it designed for the XDA?
Which ROM Version dou you have on your device?
Have you configured ActiveSync on your PC for USB Connection?
Stefan

How do ya make an SD ROM from the .nbf files

Hi - i tried to update my xda2 (Himalaya) to the uk o2 rom from the installed uk vodafone rom. but it we bellys up. now all i get is a screen showing me serial v1.06 and then when i dock it onto the cradle it shows usb v1.06 (which i have been tols is the bootloader screen -but i am not sure as the xda1 bootloader screen sayd bootloader on it).
I have tried running the rom update again but have had no luck - the computer does not recognise the device - as it says there is no drivers for it (although i have activesync installed) - but was like that since i bought it - just been using bluetooth to install programs.
When i had a xda1 i had the same problem when changing roms and was able to fix the problem by making an sd image using OS IMAGE TOOL. But this program says 'unsupported file format' when i try to make an os image of the nbf files (nk.nbf, ms_.nbf, Radio_.nbf) to my sdcard.
Does ne one know how to make an os image of the .nbf files so i can put them onto my sd card and try and resolve the problem.
any other ideas welcome and much appreciated
thanks steve
much of what you seem unsure of is describet here
http://wiki.xda-developers.com/index.php?pagename=HimalayaBootloader
http://wiki.xda-developers.com/index.php?pagename=HimalayaHowtoCopyRom
like this
"you can connect to the bootloader, either via a serial cable, and use a terminal program like hyperterm. or via usb, and use mtty. make sure you have disabled the serial or usb connection in activesync, before trying to connect to the bootloader."
'usb port cannot open'
tried mitty just gives me 'usb port cannot open' although i have my xda2 in the cradle and pluged into my usb port. when i connect to the usb port it comes up on my screen - new hardware found - no drivers found - and keep popin up as if the xda2 was found then disapears then found. although i installed the drivers when i installed activesync (have both serial and usb turned off in active sync).
have rom upgrade from o2 and extracted the .nbf files
ms_.nbf
nk.nbf
radio_.nbf
is there a way to put them on an sd card so i can put it in the xda2 and boot from that??
not that i know of
my pc always found some ms driver thingy
when i connected my pda in bootloader mode
not sure if it took it off the internet when it found the device
or if i got it with activesync
i think the problem with my computer recognising the xda2 might be down to the cradle, as from i bought it, i have always had problems charging it - depending on what way it is sittin on the cradle. i have purchased a new usb to xda2 lead and hope this will help with this problem.

Bootloader usb connection - can install/find drivers

This is connect to trying to SIM and CID unlock my vario II with version v2a of Pof's tool, however I don't think it has anything to do with the tool itself and appears to be much more fundemental.
When I put my phone in bootloader mode and connect it to my pc it goes through the usual "new usb device detected" stuff, asks to look online for the drives, etc. But after about 5 minutes of looking its says it couldnt find any drivers.
I've had a good search of the site - found a couple of suggestions it can be down to a dodgy usb cable. Tried that and it hasn't helped. I have also tried it on another pc and the same thing happened.
Any ideas?
Thanks.
James
Please ignore me. Repaired activesync from the installation cd and everything's going fine now.

spv m3000 stop on orange page (IPL/SPL)

Hi!
Recently I try to flash my SPV m3000 using HardSPL and then shelltool (with a rom wm6 HTC Professional)
And now, my pda still on orange page where I can see SPL and IPL version.
(IPL : 2.16.0001 SPL : 2.16.0001)
If I try something :
Hardspl doesnt find my mobile device!
Shelltool doesnt work and still not responding!
Any RUU say ERROR [260] Update error : The update utility cannot connect to your PDA phone!
I try that in bootloader mod. My PC see my device (in "Gestionnaire de périphérique" I dunno how to say that in english!), but Windows Mobile Device Center doesnt!
Can someone help me please?
Thx
I think that basically your device is unknown to windows enter bootloader manually yourself, do not connect it. Then open windows mobile devicecenter and select connection settings and untick the allow usb connections then connect the device and try to flash it.
I also hope you realise that you have a G4 device and are not trying to flash a g3 hardspl go here to get hardspl for g4
http://forum.xda-developers.com/showthread.php?t=332320
windows Vista is not recommended for HardSPL,its not compatible,still got issues.Try to do on winXP pc and use ActiveSync 4.5,there shudn't be any problem.
Well! there's no 'G3 HardSPL' as yet!!! its only 'HardSPL' for G4 devices.
Thx all!
Ill try on XP..
Ill say the result..
So I try.. and always the same message ERROR NO DEVICE DETECTED
I try that with XP Activsync 4.5 and my spv connected in bootloader and connected less bootloader!
So if u have any other idea.. Welcome!
You have connectivity problem,to verify if the phone is establishing connection with pc via usb cable,get the phone into Bootloaders then connect it with pc through usb cable and check small usb appear at the bottom of the Bootloader screen,if its there,than its establishing,otherwise there's a connection problem.Either usb cable is faulty or the mini usb port of the phone is damaged.
...
Its written USB in bootloader and I can see my spv in device manager..
So I explain what I think.. Maybe theres only the bootloader of orange on my spv on no more wm5.. and I cannot flash only the bootloader..
If any idea come.. Already thx!

Categories

Resources