what do i do? i flashed the kitchen. radio is 3.39 rom is 3.1.2 i have verizon. Maybe i am not installing the Verizon cab correctly? anyone have this issue? i am not actually roaming but i cant setup e-mail to auto d/l cause it keeps telling me i am roaming. every time i get a call it tells me extra charges may apply and such.. how do i fix this?
Thanks in advance for the help.
what do i do? i flashed the kitchen. radio is 3.39 rom is 3.1.2 i have verizon. Maybe i am not installing the Verizon cab correctly? anyone have this issue? i am not actually roaming but i cant setup e-mail to auto d/l cause it keeps telling me i am roaming. every time i get a call it tells me extra charges may apply and such.. how do i fix this?
Thanks in advance for the help.
Click to expand...
Click to collapse
Did you flash the leaked Sprint rom to get the radio?
yes as i dont have the proper sd card to do the "card flash trick"
yes as i dont have the proper sd card to do the "card flash trick"
Click to expand...
Click to collapse
Sounds like you let the Sprint customizations run.
Go into Device Information under Settings and read me what it says for PRI Version and PRL Version.
prl: 51056
pri: 2.03_003
pri: 2.03_003
Click to expand...
Click to collapse
That's your problem. You let the Sprint customizations run and have the Sprint PRI on your phone.
The ONLY fix for this (and still hasn't been proven to fix 100% of the time) is to relock the phone and flash back to stock rom/radio. This will revert your PRI back to Verizon. Once you've finished with that, you also will most likely have to call Verizon and have them issue you a DMU reset, as the Sprint PRI has probably screwed your DMU public key.
Flash back to stock rom/radio, then post back with your PRL version and PRI version.
gc14 said:
That's your problem. You let the Sprint customizations run and have the Sprint PRI on your phone.
The ONLY fix for this (and still hasn't been proven to fix 100% of the time) is to relock the phone and flash back to stock rom/radio. This will revert your PRI back to Verizon. Once you've finished with that, you also will most likely have to call Verizon and have them issue you a DMU reset, as the Sprint PRI has probably screwed your DMU public key.
Flash back to stock rom/radio, then post back with your PRL version and PRI version.
Click to expand...
Click to collapse
k be back in a few
prl: 50895
pri: 1.35_002
so what do i tell verizon tech when i call?
dzmedia said:
prl: 50895
pri: 1.35_002
so what do i tell verizon tech when i call?
Click to expand...
Click to collapse
That you did a hard reset after the phone crashed and it gives the message that it can't authenticate the phone. Do not call #8899 or whatever (I question what that department really does), just call 611 and go to tech support and play dumb and they will get you provisioned.
You may just be better to relock and reload stock rom then 228, or did you do that already? If you are at stock rom and authenticate, you may need to do it again after flashing radio FYI.
serfboreds said:
That you did a hard reset after the phone crashed and it gives the message that it can't authenticate the phone. Do not call #8899 or whatever (I question what that department really does), just call 611 and go to tech support and play dumb and they will get you provisioned.
You may just be better to relock and reload stock rom then 228, or did you do that already? If you are at stock rom and authenticate, you may need to do it again after flashing radio FYI.
Click to expand...
Click to collapse
i reflashed the stock rom and radio R 1.30.60 D 2.09. I tried the *228 and it said phone cannot be programmed...
dzmedia said:
i reflashed the stock rom and radio R 1.30.60 D 2.09. I tried the *228 and it said phone cannot be programmed...
Click to expand...
Click to collapse
When you allowed the sprint customizations to run, you probably caused some problems that can only be fixed by verizon at this point. You will likely need them to reset your akey and reprovision you on the network. Give 611 a call and tell them that you did a hard reset and get that message.
serfboreds said:
When you allowed the sprint customizations to run, you probably caused some problems that can only be fixed by verizon at this point. You will likely need them to reset your akey and reprovision you on the network. Give 611 a call and tell them that you did a hard reset and get that message.
Click to expand...
Click to collapse
just re-*228'd and its good to go. Phone programmed and roaming capabilities updated. No longer showing the Roaming Icon. so now i guess i need to "rehack this puppy" so what did i do wrong when installing the Radio?
dzmedia said:
just re-*228'd and its good to go. Phone programmed and roaming capabilities updated. No longer showing the Roaming Icon. so now i guess i need to "rehack this puppy" so what did i do wrong when installing the Radio?
Click to expand...
Click to collapse
You need to stop at the screen where it says tap to continue. Don't tap.
Instead, force bootloader (power + camera + reset) and load .nbh custom rom by SD, or ensure Activesync is connected (still without tapping ) and flash custom Rom by .exe.
ahhhh Gotcha.. So I CAN ... thanks for the help!!! Both of ya!!! i'll post up if it workded!!
dzmedia said:
ahhhh Gotcha.. So I CAN ... thanks for the help!!! Both of ya!!! i'll post up if it workded!!
Click to expand...
Click to collapse
Yeah, If your on Verizon or other non-Sprint network, don't listen to those people who say to let the Sprint stuff run ... you will likely jack your phone up. It is possible to really cause problems that are difficult to flash out (trust me)
Tell me you checked to see if data worked before you started again...
gc14 said:
Tell me you checked to see if data worked before you started again...
Click to expand...
Click to collapse
I didn't .. hmm.. but i had no problem with data before... why would i have one now? i use my username and the password to set up the data connection
hmm... well guess i should have checked data.. cause now that i tossed on a PPCkitchen rom the data connection will not work getting a wrong login/password error... hmm/.
When you reset your phone, you lose authentication and need to be reprovisioned to work on the network. You may be able to get there with login settings from here, but a call to Verizon and/or a reflash may be a reality at this point.
hmm... well guess i should have checked data.. cause now that i tossed on a PPCkitchen rom the data connection will not work getting a wrong login/password error... hmm/.
Click to expand...
Click to collapse
Serf it has nothing to do with that. It's probably his DMU public key like I said above.
Dial ##778 and then press send. Press Edit, then enter 000000 for unlock code.
Click on View Info, navigate to M.IP Default Profile, and tell me if the values for HA Shared Secret and AAA Shared Secret are blank.
Click on View Info, navigate to Security, and tell me if the values for HDR AN AUTH Password and PPP Password are blank.
For anyone else reading this...it causes SERIOUS problems if you let the Sprint customizations run and you're not a Sprint customer. PLEASE be careful if you're using the Sprint roms to get your radio.
Related
Hi all.
with the 6800-
I flash nexvisions rom and the new radio. After reading ppcgeeks tutorial, I thought I needed to run IOTA.cab to get my data settings even though I'm on Verizon. Well, after doing a *228 and calling verizion to get my calls to go though, my data is now screwing up.
The problem is- when I run internet explorer (with google mobile as my homepage) it chokes after about 50 K downloaded and wont finish. The data connection is lousy. If I try to close out my data connection using the connection manager it comes up with a warning about IOTA data errors.
Now I know that vzw users do not need IOTA. Is there a way to reset what IOTA does to your data connection settings without doing a hard reset? I can't find a 'unintstall' IOTA.cab anywhere.
Anyone have any ideas?
Cook ROM as Verizon, not Sprint?
Maybe just run the ROM again
I can not think of a good way to get it all out but maybe someone has an idea. I am on VZW and it worked perfectly.
You should reflash.
Perhaps you shouldn't use Nexvision's ROM since it obviously has Sprint "parts" in it that seem to be interfering.
Here is what worked and is still working very well for me. I have no data or voice issues at all right now:
Geckotek said:
In fact, all is well.
I flashed back to the stock VZW ROM (third time I think), I made sure all of my provisioning issues with Verizon were worked out (finally had the tech "kick the switch").
1) Then I proceeded to load the 2.4 bootloader,
2) then the 3.16 Unauthorized Sprint ROM w/ radio,
3) then finally installed a cooked DCD 2.3.2 ROM.
Things to note:
1) I never let the Sprint ROM boot up (this is VERY important!!)
2) I had no signal so ran *22802 then hit End as soon as it connected
3) Still no signal after reboot
4) No A key, MSID, or MDN issues, but I did re-enter the MSID and MDN as discussed in other threads
5) After re-entering MSID and MDN then after reboot I had signal (even though they are there and correct, type re-enter the information anyway)
6) never had to run *228 to OTA program (in the past programming with *228 has reversed the effect of re-entering the MSID and MDN)
In general, I feel that the OTA from VZW sends down some programming that conflicts with the 3.27 radio...but I have nothing to prove that.
GPS is running great (I just loaded the AstroGPSLauncher)
Not sure about Rev A. It does seem snappy. What's a good site to test from the phone?
I'm happy and not re-flashing until a solid radio for Verizon arrives.
Click to expand...
Click to collapse
Thanks everyone for your feedback.
First- I'll try a hard reset first and see if that clears it up.
Then if that doesn't work, I'll try reflashing nexvisions rom and see if that clears it up.
If that doesn't work, I'll reflash trying the dcd rom.
spreeway said:
Thanks everyone for your feedback.
First- I'll try a hard reset first and see if that clears it up.
Then if that doesn't work, I'll try reflashing nexvisions rom and see if that clears it up.
If that doesn't work, I'll reflash trying the dcd rom.
Click to expand...
Click to collapse
If that doesn't work, you should do like I did and start with a clean slate. All the reflashing of ROMs and radios did me no good. Whatever issues I had were not going away with just another flash from one ROM to another.
Hard resetting fix everything.
Anyone having issues with the GPS working? I'm unable to get any GPS Sats locked at all. I can do everything else just fine.
Just verifying, did you check the steps in the GPS thread?
I'm installing 3.0 for the first time right now. Will test GPS soon.
Yeah
I've been using GPS for a bit now with the older ROMs. I just want to confirm other VZW have it working.
Works great here. Be sure you have Be sure your Location Setting is set to Location On.
If you are using Google Maps, be sure to turn on the GPS in the GMM menu.
Also, be sure you are outside, not in a building.
etexter said:
Anyone having issues with the GPS working? I'm unable to get any GPS Sats locked at all. I can do everything else just fine.
Click to expand...
Click to collapse
DCD 3.0.0 works Excellent on my XV6800
GPS improved. I get way more satellites.
I modified the ROM a little bit and on a Bare ROM flash I get 28MB and with some major apps i get down to 25MB to 26MB
etexter said:
I've been using GPS for a bit now with the older ROMs. I just want to confirm other VZW have it working.
Click to expand...
Click to collapse
Yes, it works. I have been using Google maps. One thing, I noticed this morning is starting it up after an hour being off and in a building is "Google Maps" would get hung at "Initializing GPS" when I selected "Use GPS". The only why I have gotting it to work again was a soft reset. Not sure what is going on, yet.
Everything works fine on my xv6800 with dcd 3.0.0 including GPS.
No more issue where it takes 5 seconds to connect to a call when answering...among many other fixes from the leaked rom.
Interesting
Seems to be related to building the Kitchen on Vista for me. I can reproduce the problem if I build the kitchen on Vista. If I use all the same options on XP, it works fine. Strange. I guess something it messing with the build process on Vista. Solved for me at least.
Stupid question... assume you need the latest radio for this (3.35 or whatever, I have 3.27)? I'm a little leery on upgrading again considering I had to call VZW and apparently they're hip to people flashing these roms.
J Shed said:
Stupid question... assume you need the latest radio for this (3.35 or whatever, I have 3.27)? I'm a little leery on upgrading again considering I had to call VZW and apparently they're hip to people flashing these roms.
Click to expand...
Click to collapse
Yes, you need 3.35 to work with DCD's 3.0.0. I did not have to call VZW this time going from 2.3.2 to 3.0.0, I can't confirm if it will retain the A-key authenication from previous versions, haven't been back there for a couple of weeks.
rschell said:
Yes, you need 3.35 to work with DCD's 3.0.0. I did not have to call VZW this time going from 2.3.2 to 3.0.0, I can't confirm if it will retain the A-key authenication from previous versions, haven't been back there for a couple of weeks.
Click to expand...
Click to collapse
hmm... I don't have an A key on mine, but when I re-entered all the info it wouldn't let me place a call.
I'll give this a wack maybe tonight or tomorrow. I JUST upgraded to 2.3.2 and this comes out... figures.
I have only ever had to enter the A-key once, the very first time I flashed a ROM to the phone. Every upgrade since has just worked.
The latest is working great for me under VZW today. I was running 2.3.2 before that. I flashed the sprint ROM to get the new radio, then immediately flashed the ROM I built for verizon from the 3.0.0 kitchen. Did a *228 1 just in case, and verified that the PRL after that was identical to the one it had before I did the upgrade (##775 SEND, 000000).
EVDO, wifi, GPS all working. I like the new wireless today plugin.
I'd still love to see an up to date step by step on how to get VOIP working, I've never managed to get anything VOIP related on this phone.
GREAT WORK AS ALWAYS DCD! Thank you! Remember to show dcd the monetary appreciation guys.
rschell said:
Yes, you need 3.35 to work with DCD's 3.0.0. I did not have to call VZW this time going from 2.3.2 to 3.0.0, I can't confirm if it will retain the A-key authenication from previous versions, haven't been back there for a couple of weeks.
Click to expand...
Click to collapse
rschell, i'm very curious to hear the exact steps you took to upgrade, so that you did not have to call verizon.
some specific questions i also have:
1) did you do the entire sprint upgrade to get the radio, or did you just install dcd's standalone 3.35 radio?
2) if the entire sprint upgrade was used: did you let the customizations run, or did you reboot into bootloader before that point, and if so, where exactly?
3) did you have to re-enter any settings in ##778 ?
thanks for any help you can offer!
a_lazy_dude said:
rschell, i'm very curious to hear the exact steps you took to upgrade, so that you did not have to call verizon.
some specific questions i also have:
1) did you do the entire sprint upgrade to get the radio, or did you just install dcd's standalone 3.35 radio?
2) if the entire sprint upgrade was used: did you let the customizations run, or did you reboot into bootloader before that point, and if so, where exactly?
3) did you have to re-enter any settings in ##778 ?
thanks for any help you can offer!
Click to expand...
Click to collapse
Do not let the customizations run, just soft reset before they do. Now run the new kitchen creating your ROM. Should be nothing else to do.
I've never had to call Verizon through any flashes including when 3.16 first came out.
J Shed said:
hmm... I don't have an A key on mine, but when I re-entered all the info it wouldn't let me place a call.
Click to expand...
Click to collapse
At least to Verizon customers, the EPST A-key will always be blank. It is a 26 digit number generated by Verizon that is different each time you authenticate. Once you enter it, and the device reboots the A-key disappears. I have had to call and get a new A-key every time I have made the switch from non-Rev A to Rev-A. Not sure this new radio is any different. I have had excellent support from Verizon, every time I have called, you just have to let them walk through their diagnostic tests.
The authentication issues appear to be Network Switch dependent. I just happen to be in one of those areas.
blazingwolf said:
Do not let the customizations run, just soft reset before they do.
Click to expand...
Click to collapse
So if I just go ahead and reboot while, say, I'm in the screen calibration after my initial boot, I should be in the clear?
I was thinking of yanking the battery at this point, putting it back in, rebooting into bootloader, then flashing either by the RUU or SD (can't recall if the RUU works while in bootloader mode or not, so i've got the SD option to fall back on). Or should i just do as you say: soft reset, let the device come all the way back up, let activesync connect the phone as a guest, then run the RUU w/ DCD 3.0.0?
you don't even have to soft reset, or manually enter the bootloader. once you finish flashing the sprint update the phone will boot and will stop at the tap screen to set up device screen...at this screen activesync WILL connect. just run the kitchen and the phone will AUTOMATICALLY put itself into the bootloader and flash the new rom without running sprint customizations. the sprint customizations only run after you set the device up, not before.
gcincotta said:
at this screen activesync WILL connect.
Click to expand...
Click to collapse
bam! thanks man, it's details like these that always get glazed over in the flurry of "i installed the new rom no problem!!!!111one" posts that i'm seeing all over the place around here.
a_lazy_dude said:
rschell, i'm very curious to hear the exact steps you took to upgrade, so that you did not have to call verizon.
some specific questions i also have:
1) did you do the entire sprint upgrade to get the radio, or did you just install dcd's standalone 3.35 radio?
2) if the entire sprint upgrade was used: did you let the customizations run, or did you reboot into bootloader before that point, and if so, where exactly?
3) did you have to re-enter any settings in ##778 ?
thanks for any help you can offer!
Click to expand...
Click to collapse
Starting from 2.3.2 (if you start from the pre-GPS ROM, you may need a different SPL).
I did both the radio and ROM in one upgrade, I just did not let the customizations run, actually I forced it to the boot loader just after the HTC Mobile splash screen came up. Then I installed DCD's 3.0.0 ROM from the boot loader (2.40!). See http://forum.xda-developers.com/showpost.php?p=2011926&postcount=3
Success!
Data connection confirmed working
Incoming/Outgoing calls confirmed working
Incoming/Outgoing texts confirmed working.
GPS confirmed working.
no calls to VZW customer support whatsoever.
so far, no *228 updates at all (prl seems to be current, 50989; confirmed within ##778)
Here's a quick rundown of my starting conditions, and what I did (basically, just followed gcincotta's instructions exactly)
Starting conditions:
-NexVision's no2chem 5051 - based ROM w/ 3.27 radio
-2.40 SPL
Upgrade procedure:
1) Connected phone via activesync
2) ran the official Sprint/HTC 3.35 upgrade utility, which ran successfully.
3) On the initial boot, I let activesync connect while the phone was still holding on the "tap screen here to begin" screen
4) I then ran the RUU using a DCD 3.0.0-based rom (NexVision's VZW 3.0.0), which was successful.
5) After initial boot on NexVision's rom, I let the customizer run (i think it's just an SD power management program). It soft reset, and I was good to go.
That's it! Once it booted up after the second install, everything that I confirmed above was working perfectly.
Thanks again guys!
After accidentally running the sprint PRI update on my xv6800, I was stuck with the phone thinking it belonged on Sprint and was roaming. I'm not completely foolish and I did not purposely disregard the instructions; I downloaded it elsewhere and it was labeled as "GPS fix" or some such. Anyway, I relocked, flashed to stock Verizon, called 611 and had them do a DMU reset. No problems, everything worked fine after calling 611. Reflashed to olipro 2.40, radio 3.42.30, and dcd 3.2.0. After flashing everything was fine, I ran the carrier cab, did *228,1 and everything seemed to work correctly. I then ran Sashimi to reinstall my software, rebooted. Well, the roaming indicator was back after reboot. I thought that perhaps the Sprint PRI update cab had made its way into my autoinstall folder, but that was not so. Do you guys have any ideas that might explain how this happened? I am flashing back to 3.2.0 and don't want to repeat this experience
playoff beard said:
After accidentally running the sprint PRI update on my xv6800, I was stuck with the phone thinking it belonged on Sprint and was roaming. I'm not completely foolish and I did not purposely disregard the instructions; I downloaded it elsewhere and it was labeled as "GPS fix" or some such. Anyway, I relocked, flashed to stock Verizon, called 611 and had do a DMU reset. No problems, everything worked fine after calling 611. Reflashed to olipro 2.40, radio 3.42.30, and dcd 3.2.0. After flashing everything was fine, I ran the carrier cab, did *228,1 and everything seemed to work fine. I then ran Sashimi to reinstall my software, rebooted. Well, the roaming indicator was back after reboot. I thought that perhaps the Sprint PRI update cab had made its way into my autoinstall folder, but that was not so. Do you guys have any ideas that might explain how this happened? I am flashing back to 3.2.0 and don't want to repeat this experience
Click to expand...
Click to collapse
When you update the PRI, it does not install into your ROM, it actually updates something inside the phone (similar to flashing your radio/etc). You need to find a verizon PRI ripped from the verizon stock rom (if it is even there) and install and run PPST.exe again. My original post he reposted had said not to install on another carrier in big red letters
Read this here, should do the trick.
After doing yet another relock, stock rom, and *228, I installed the latest PPC Kitchen 5060 rom (set to Verizon) and new radio (3.42.30). As soon as the phone boots, it thinks it is roaming and *228,1,2 does not help at all. I've done all the steps on the thread that serfboreds recommended. It still thinks it is roaming. Any advice?
I just don't understand this. The phone is fine until I install DCD 3.2.0 or nue 5060, after which it thinks it is roaming again. Getting desperate here...
playoff beard said:
I just don't understand this. The phone is fine until I install DCD 3.2.0 or nue 5060, after which it thinks it is roaming again. Getting desperate here...
Click to expand...
Click to collapse
Reload stock and take to store. This is a common outcome after letting Sprint customizations run. It really hoses your phone and can cause irreparable damage.
Any other suggestions?
serfboreds said:
Reload stock and take to store. This is a common outcome after letting Sprint customizations run. It really hoses your phone and can cause irreparable damage.
Any other suggestions?
Click to expand...
Click to collapse
The only problem is that the phone seems to look and work fine when the stock rom is loaded, as long as the DMU reset is done for data. Problems don't appear until I load a custom rom. I can't figure out why the phone shows verizon network (1.35_002 PRI) when the stock rom is installed, but then shows sprint (2.03_003) when I load a non-carrier specific DCD roms and even carrier specific roms (i.e. ppckitchen 5060 for vzw).
I don't know how I can convince a verizon tech to swap when the phone appears normal with the stock rom.
playoff beard said:
I just don't understand this. The phone is fine until I install DCD 3.2.0 or nue 5060, after which it thinks it is roaming again. Getting desperate here...
Click to expand...
Click to collapse
When you do update to DCD 3.2.0, Are you installing the Verizon Carrier Cab?? Also, How are you getting the radio onto the device??
Hmm, works normal with stock rom and radio but funky when you upgrade?
Sounds like you are not loading the radio or verizon carrier as azclown suggests. after going back to vanilla rom, upgrade using gc's newest radio via sd, then load dcd 3.2.0, let his customizations run, then load verizon carrier and you should be fine. Dont load the newest sprint rom/radio.
serfboreds said:
Hmm, works normal with stock rom and radio but funky when you upgrade?
Sounds like you are not loading the radio or verizon carrier as azclown suggests. after going back to vanilla rom, upgrade using gc's newest radio via sd, then load dcd 3.2.0, let his customizations run, then load verizon carrier and you should be fine. Dont load the newest sprint rom/radio.
Click to expand...
Click to collapse
I've been unlocking with olipro 2.40, flashing the new 3.42.30 radio from a microSD card, and then installing the custom rom while still in the bootloader. After installing DCD 3.2.0, I ran the carrier cab and then used *228. Plus, I wouldn't think the carrier cab would be the issue, because I had the same problem when installing PPCkitchens 5060 verizon rom.
-Update: I've tried using radiorefurbish.exe /refurbish to reset my phone to Verizon, but when I run the radiorefurbish.exe using resco explorer, nothing seems to happen. Any more suggestions?
Problem Solved:
I finally resolved this by installing and running this version of radiorefurbish. I ran it using resco explorer with the argument '/refurbish'.
Thanks to you guys and drellisdee at PPCGeeks. You guys rock. I was horrified that I was going to be stuck with the tock VZW rom.
Take the following screenshots (making sure to block out any personal information) and post them:
Device Information
EPST->Security
EPST->M.IP Default Profile
Then, flash back to stock, re-take the screenshots, and post them.
Finally, flash back to 3.42.30 and 3.2.0, install nothing except the carrier cab, re-take the screenshots one last time, and post them.
playoff beard said:
Problem Solved:
I finally resolved this by installing and running this version of radiorefurbish. I ran it using resco explorer with the argument '/refurbish'.
Click to expand...
Click to collapse
I've got the same problem and I reflashed to stock Rom and reflashed to custom. Still stuck in roaming. Could you give details on exactly how you ran resco with an argument?
Thanks
I wonder how he got that working. i've used that file and still have the issue. Yes... I used resco explorer and tried the argument... but got nowhere
nitro66215 said:
I wonder how he got that working. i've used that file and still have the issue. Yes... I used resco explorer and tried the argument... but got nowhere
Click to expand...
Click to collapse
i distinctly remember that one of the customizations after flashing back to stock was radiorefurbish. youve gone back to stock right and loaded the vz PRL?
aguas said:
i distinctly remember that one of the customizations after flashing back to stock was radiorefurbish. youve gone back to stock right and loaded the vz PRL?
Click to expand...
Click to collapse
Yup. and yes... it did run when the Verizon stock ran it's customizations. The PRI stays as sprints PRI 2.00_003. This is the main issue. Also, the ERI is 0. I've tried updating the ERI via ##eri... to the correct 4.eri... but it just gives me a write error. Under ##PROGRAM... the ERI fails to read. Hence my dilemna with the stupid Roaming indicator. I've been back and forth flashing different roms, and am pretty fed up with it actually. This is a Sprint Mogal "Cloaned" as my original VZW XV6800. I left the 6800 in the box.
check this
this wont help for the cloned moguls. But it will help the xv6800 users if they install sprint customizations.
http://forum.ppcgeeks.com/showthread.php?p=401137#post401137
believe it or not, a few months ago i let the sprint customizations run and used it like that just for the better signal...only downfall was no data services....i just switched back to verizon radio stuff yesterday and got my data reactivated
ever since I installed the rom, my wifi stopped catching signals completely. now I just added the data plan on my phone, and the data isnt working either. Any idea what the problem could be?
EDIT: ALSO I have a verizon phone, yet when I soft reset, Alltell shows up instead of the Verizon Logo. Maybe this has something to do with it
fix
What radio are you using?
Have you tried hard resetting and skipping the customizations? I don't see why Alltel would be displayed if you did a fresh ROM flash, as there is nothing associated with AllTel unless you installed the wrong CAB.
Best bet would be: Go to the Radio 3.40.30 thread, download the Unlocker for Olipro 1.2 and most recent Radio...flash the Unlocker, let it get into Boot Loader mode, then flash the Radio. Then it will boot up again, and flash your phone with Olipro 2.4, then flash the 3.2.3 DCD rom. Install carrier cab, and the Arcsoft one if you need it....then you're done.
The data connection may be another story...but I'd first get the ROM up and going, with the ability to make phone calls / send texts.
scotcha12345 said:
What radio are you using?
Have you tried hard resetting and skipping the customizations? I don't see why Alltel would be displayed if you did a fresh ROM flash, as there is nothing associated with AllTel unless you installed the wrong CAB.
Best bet would be: Go to the Radio 3.40.30 thread, download the Unlocker for Olipro 1.2 and most recent Radio...flash the Unlocker, let it get into Boot Loader mode, then flash the Radio. Then it will boot up again, and flash your phone with Olipro 2.4, then flash the 3.2.3 DCD rom. Install carrier cab, and the Arcsoft one if you need it....then you're done.
The data connection may be another story...but I'd first get the ROM up and going, with the ability to make phone calls / send texts.
Click to expand...
Click to collapse
Actually that's the funny part, I CAN make calls and texts. I didn't brick my phone or anything, GPS works fine too. The only problem is the WIFI and data connection - should I still go ahead and try that new rom?
problem
I would definitely suggest the whole procedure, from Radio flash and then further to the ROM reflash.
If after you've done all those things, and your WiFi is jacked, at least in my mind, the things probably broken.
Data connection could just be a matter of password being incorrect, or needing a DMU reset. See if you can do the flash to get the WiFI working first.
scotcha12345 said:
I would definitely suggest the whole procedure, from Radio flash and then further to the ROM reflash.
If after you've done all those things, and your WiFi is jacked, at least in my mind, the things probably broken.
Data connection could just be a matter of password being incorrect, or needing a DMU reset. See if you can do the flash to get the WiFI working first.
Click to expand...
Click to collapse
Do you have aim/msn or something? I updated to DCD 3.2.3 and the wifi works great now. But the data network keeps saying I have the wrong username and password. I even called up verizon for that and they dont know what the problem is. I bet it's incredible simple :/ What is a DMU reset????
Thanks a bunch in advance
EDIT: Also my phone is RIDDLED with alltel settings when it should be verizon, even AFTER all these updates!! I went into the EPST and a bunch of things had alltel. need help fast :/
inbox
check your private messages
Ok pm'ed you back! let me know if you get my email, if not i'll just post it here
I've upgraded and changed to:
NueRom v2.2
Chose Verizon, checked the EPST. Everything looked fine, but the m.IP Default Profile is still [email protected].
I was able to get an A-Key (and a password???) from the rep. The A-Key is pretty long.. does that sound about right? Anyway DATA still doesn't work. Any help is greatly appreciated, I'm trying to get this up and running as soon as possible
Ok... i have a phone programmed on my network (VZW) *228 , 1 and *228 , 2 done. Data is working. Messaging is working. The only problem I have not accomplished, is getting the Roaming Indicator to go away... and when people call... I get the roaming message. I looked at the EPST compared to my other phone.... and it looks right. What's missing?
Bump......
There has to be somebody that has an idea on what the PRL / PRI should be in order to get rid of this Roaming issue.
There is a site that shows all of the latest prl's for all carriers...I just tried to find it for you....I know it is over at ppcgeeks....if I find it I will post it back....just changing the prl should fix it....
flyers2114 said:
There is a site that shows all of the latest prl's for all carriers...I just tried to find it for you....I know it is over at ppcgeeks....if I find it I will post it back....just changing the prl should fix it....
Click to expand...
Click to collapse
I've done that... something like colorodo.com/prl... whatever. Did that... and also let the Verizon *228 , 2 load the latest PRL. It's newer than the one on that site. Still says I'm roaming though.
PRI : 2.00_003
PRL : 51056
nitro66215 said:
I've done that... something like colorodo.com/prl... whatever. Did that... and also let the Verizon *228 , 2 load the latest PRL. It's newer than the one on that site. Still says I'm roaming though.
PRI : 2.00_003
PRL : 51056
Click to expand...
Click to collapse
May be dumb question but did you go into the phone settings and check them...
flyers2114 said:
May be dumb question but did you go into the phone settings and check them...
Click to expand...
Click to collapse
As I said in the first thread.... I compared as many settings as I could in EPST to my actual Verizon XV6800... and they match. That's what's confusing.
PRI : 2.00_003
Click to expand...
Click to collapse
This is why you're roaming. This is not a Verizon PRI. You let some other carrier's customizations run. You need to flash back to stock, let VZW customizations run, then upgrade again. It's the only way. Your data may not work either after you flash back to stock, so you may need a DMU reset.
gc14 said:
This is why you're roaming. This is not a Verizon PRI. You let some other carrier's customizations run. You need to flash back to stock, let VZW customizations run, then upgrade again. It's the only way. Your data may not work either after you flash back to stock, so you may need a DMU reset.
Click to expand...
Click to collapse
I was afraid of that. The ERI keeps erroring as well when I try to write "4" to it.. GRRRR...
I'm still trying to get this to work... but with VZW Stock 2.09 and radio 2.13 (because the normal method with the 1.30.60 just says no radio)... and the customizations ran... when in the main screen of WM... it still says roaming. I'm guessing because I haven't programmed any settings yet... IE... phone number.... SID... etc.
Edit:
Ok... Somethings not right. Even after running the stock verizon... letting it "Customize" and then updateing to the latest DCD... In QPST there is still SPCS in the NAM settings areas.... and the roaming is still showing.
Also, If I do a ##eri.. to load the eri.. it gives me a write failure. and.. when I do a ##7764726... for ##Program.. the ERI
reading... fails.
PRI still reads 2.00_003
Is there a way to "ERASE" the device and start over? That way the correct ERI/PRI will be loaded?
I guess because the GPS Radio/Rom from sprint is what ran and did the customizations.... a Verizon Base Non-GPS radio/Rom customization isn't erasing the Sprint data? Even after verizon Customizations... QPST says SPCS.
nitro66215 said:
Is there a way to "ERASE" the device and start over? That way the correct ERI/PRI will be loaded?
Click to expand...
Click to collapse
Nobody????
If you havent already try this, Id suggest re-flashing to the stock vrzn ROM. That may fix your problem, but Im not sure, as I am just taking a stab in the dark.
I've had to do it before and it pretty much returns ur phone to how its "supposed" to be.
loki1931 said:
If you havent already try this, Id suggest re-flashing to the stock vrzn ROM. That may fix your problem, but Im not sure, as I am just taking a stab in the dark.
I've had to do it before and it pretty much returns ur phone to how its "supposed" to be.
Click to expand...
Click to collapse
Been there. Done that. It's a Sprint Mogul. So, the Base system information that gets retrieved after the flashing is done, is all sprint. That's what I want to edit. If I can get the Verizon stuff in the ERI/PRI... I'd be good to go. The phone works as a verizon phone. Text/Data/Email... etc. It just shows roaming.
Ok... I was hoping the new update would fix it. I ran the vzw update on UtStarcoms site... let it update the PRI... and It still says I'm roaming on my Cloned Mogal to Verizon.
GC14... or DCD... Do you know about this?