I have a VZW HTC6800 and I need to get the SPL 2.40 on the device so I can move forward. I get to the point where it ask for the disconnect/reconnect but on the reconnect I cannot get it to see ActiveSYnc. I have searched for an answer and cannot find one. What danger would I have if I did not disconnect and continue will I still get the 2.40?
parcou said:
I have a VZW HTC6800 and I need to get the SPL 2.40 on the device so I can move forward. I get to the point where it ask for the disconnect/reconnect but on the reconnect I cannot get it to see ActiveSYnc. I have searched for an answer and cannot find one. What danger would I have if I did not disconnect and continue will I still get the 2.40?
Click to expand...
Click to collapse
you can make sure you got 2.40 correctly, by manually entering bootloader. (power+camera+reset) if it says that you have 2.40, then you got it. so you can proceed, if not then go back and try again to make sure you get it
I have a VZW HTC6800 and I need to get the SPL 2.40 on the device so I can move forward. I get to the point where it ask for the disconnect/reconnect but on the reconnect I cannot get it to see ActiveSYnc. I have searched for an answer and cannot find one. What danger would I have if I did not disconnect and continue will I still get the 2.40?
Click to expand...
Click to collapse
You're not supposed to see activesync at that stage. Disconnect and reconnect, and continue with the process.
Make sure also that you HEAR the tones that acompany the disconnect and connect... You will hear tones.... On disconnect you will hear tones that decend, and on connect they will ascend....
gbenj said:
you can make sure you got 2.40 correctly, by manually entering bootloader. (power+camera+reset) if it says that you have 2.40, then you got it. so you can proceed, if not then go back and try again to make sure you get it
Click to expand...
Click to collapse
OK...will try again...when I disconnect then reconnect this is done in the DOS window. After that I do I do hit continue and the RUU I guess you would call it comes up. In that procedure it request that an active sync connect be made and this is where I have been for hours trying to get it to connect. If I never disconnected in DOS I would be OK but I know this is required...
Oh well...must mean I do not need it...
OK...will try again...when I disconnect then reconnect this is done in the DOS window. After that I do I do hit continue and the RUU I guess you would call it comes up. In that procedure it request that an active sync connect be made and this is where I have been for hours trying to get it to connect. If I never disconnected in DOS I would be OK but I know this is required...
Oh well...must mean I do not need it...
Click to expand...
Click to collapse
Yeah it's fine...just keep going...as long as when you reconnect, at the bottom of the bootloader screen it says USB and not Serial, then you're fine.
Thx...that info did help...
For any newbies like me this might help. I followed the instructions hanging off each word for each step. One the SPL update entering into the Windows GUI and I attempting over & over to connect to active sync because the instructions state to do so before checking the box. Maybe it was dumb of me but I never saw it stated to ignore that step from WiKi page...so hope that helps someone down the road.
Pros...now that I am updated is it safe to add tweaking apps like tweaks2k2 or Pocket Toolman. I am sure some reg hacks are added but do not want to cross up anything with the new 312 rom? Please advise?
I have vista64 is there a way to install the spl using vista64 or the sd card
When I posted this I was on the 2.40 boot loader but now I am on the 2.47. This loader is loaded from the SD card so all the trouble I posted you will not see. Sorry I do not have the link but do a search for the 2.47 you will see it and how to load it off a SD card.
i really need help,
i started off connected to activesync but thn im getting error saying pput.exe is being used by something else now i have colored screen with TITA100 and SPL-1.30.Olipro
i dont know what to doo, please someone help, new in these filed.
Thank you
EDITED: got it working... sorry
Thx
my turn
I am trying this on my old 6800 ( broke rubber power button) before I do new one.
I am on Verizon, don't care about GPS, running STB but really like features on 6.5. I have read everything I can find and still confused. Do I need to change anything if all I want is 6.5?
Also, when asked to plug and unplug usb, I get tones remove and replug, but then I get connection error and stay in 3 color spl-2.40
Thanks...
Jerry
stuck in bootloader 1.20
i tried to upgrade my daughter's Titan, firmware 1.4 so fsirly old, no gps. When I started the phone hooked up fine with Mobile Device Center. I ran Olipro 1.2 fine did the unplug and replug fine and got success message. Then couldn't restart the phone and now it won't connect through Device Center, so nothing else will run. Wanted to run Olipro 2.40 and then flash a GPS enabled rom and radio.
I have read everything I can find on here, but without a connection thru Device Center I am stuck.
Have I bricked the phone?
Ok got the phone working again with extbl.
Thank for listening.
Related
Ok, I've been trying to update my 8525 for hours...here is my problem. First, I tried to HardSPL-v7 but I kept getting an "Error [240] File open". I think this is preventing me from doing any ROM update. When I try to run the Cingular ROM update activesync shuts down and I get a connection error, I think it is "error [260]". I have wiped or cleaned out my 8525 so that I am back to day one. I have tried both ROM updates on 2 separate computers and I get same error messages on both computers. I have searched the Wiki's but have found nothing, so please help. As you can tell, I am a virgin to ROM updates so please go gently.
I should add, my present ver. ROM AKU 2.3 (1.34.502.7018.01H) SPL 1.06 IPL 1.01. Radio is 1.16.
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
I have, I have even tried the mtty "fix" but I had problems with that as well. I get a modem connection screen but there is nothing about a USB connection.
Bit more info would be nice, which ROM are downloading, and where from??
Also what procedure are you doing to update?? EXACT info please.
mrvanx said:
have you taken a look at my Safe WM5 Upgrade Guide??
If you follow this guide EXACTLY, you should be fine.
Click to expand...
Click to collapse
Ok, I just tried it 2 more times, Hard-SPL. It flashes to the 8525 and goes into bootloader and shows the following "HERM100 IPL-SSPL by Des HERM100 SPL-1.09.ds" at this point activesync 4.5 shuts down the 8525 is stuck in bootloader (it never reboots) and after a few minutes I get "Error [260] Upated Error". Hard SPL shuts down and the 8525 is stuck in bootloader mode. At this point I have been disconnecting the USB cable and doing a soft reset, once the phone is on, I go into bootloader and the old info shows up SPL 1.06 and IPL 1.01.
Let me have a think, firstly do you have the latest versions of the .net framework installed?
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
mrvanx said:
Let me have a think, firstly do you have the latest versions of the .net framework installed?
Click to expand...
Click to collapse
I have .Net 1 thru 3.5 (pre-release) installed on the computer that I can not get to run any ROM updates.
9
compudds said:
I was able to finally run HardSPLv7, I had to do it on another computer. Now, I would like to update to RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe. I assume I should use the same computer that I used to successfully run HardSPL. Do I need to rebuild the rom file with RUUWrapper.exe (CustomRUU by olipro) & Dutty's Good NBH Tool, before running the RUU_Hermes_CINGULAR_WWE_2.15.502.3_6275_1.40.30.00_108_Ship.exe update?
Click to expand...
Click to collapse
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
mrvanx said:
Yes if you carry on the guide past flashing hardspl you will get the radio updated aswell.
Can i ask, what is different on the computer you used???
Click to expand...
Click to collapse
Off hand, the major difference would be Intel (worked) vs. AMD (failed) but I doubt that is the problem, you would be flooded with questions due to so many computers that have AMD chips. The USB cable was the same as well. I'll have to think about that...
Definatly check your "failed" computer is up to date with .net and everything else, most likely a software problem.
I have this problem as well..
AT&T 8525 windows moble 6 trying to install the hardspl v7.
v3.5 and 3.0 .net framework.
the RUUwrapper program gets to the 'verifiying info' screen then give me an erroe 240 message. 'the update utility can not open the requested file.'
any help would be great. Looking to add the touch it interface.
thanks,
Mike
Read the post Hard SPL at the top of this forum and go to page 116 ( I believe its post #1160) and use the sd card method. You don't need to use the pc at all. I generally flasah ALL os's using the sd card method as it seems to be safer then using the usb method. No "sync errors" to deal with.
Cheers...
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
I loaded it thru the sd card just as the post above suggested. It loaded the hardspl just fine. My PPC seems to run faster as well.
Thanks for the help! it is much appreciated.
blackphnx said:
I have the exact same problem..
When it goes to tri-color screen, the USB connection goes off and windows will pop up the search for driver dialogue box.. then afterward another dialogue box will appear saying Error [260].
I tried restarting my pc and device (even removing the battery) but still failure
Any help would be highly appreciated. Thanks.
Click to expand...
Click to collapse
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
swimmy said:
One thing that i have learned from flashing my 8525 is to remove any USB device except the 8525. This has worked for me.
Click to expand...
Click to collapse
But my mouse is on USB. I might try on different computer and post back the results.
UPDATE
I tried using my friend's laptop and it installed without a problem. I think the issue is with the .NET framework. I installed the latest one before flashing and it worked fine. Hmmm.. Im not sure about this tho.
Hello.... Try the sd card method. You don't need the computer...
Sorry if I sound condescending, but, I seem to find a lot of people saying that they have sync problems. Solution, Take the pc out of the equation (except to load files onto sd card). It is SOOO much safer then using the pc, no "sync" problems, no chance of usb being disconnected, reset button being hit or , worst case scenario, power failure...
You have to either have little or no battery power or MANUALLY hit the reset button with the stylus to stop the flash...
And thats my 2 cents....
Refer to post #13 to find out how to use sd card method to flash hard spl...
Cheers...
sd card method???
how?
Hey everyone,
i am so upset and lost; words cannot describe it.
So i installed WM6 black shadow and everything was working except for SMS and MMS. So i am like ok i can live with that for a day till custel' rom will come out. SO i decided to upgrade the radio to 1.43 and boom here is where the problem started, No GSM on boot up. Phone doesn't boot up. I tried install 1.40 over again, still nothing. No i tried upgrade the the rom itself, i tired custel 2.5 and nothing and i tried the new Cingular rom, still same problem. the roms flash all the way. I read the wiki, and saw the mtty.exe thing but that doesn't work for me either. I am really lost and don't know what to do.
Specs
cingular 8525
hardspl v7 cid and sim unlocked.
PLEASE HELP
4.13?? 4.10??
Where did you download these radios from??
or do you mean 1.41 or 1.43??
Yeah thats what i meant, 1.40 and 1.43 sorry. You can see how upset i am.
Thanks Again
Well, if your phone turnes on .. it's not a brick.. lol .. it IS fixable... When you turn the phone on does it go RIGHT to the 3 colored screen?
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
If you are superCID I don't see how flashing a radio could have messed up your phone.. that's weird.
mrvanx said:
@dan5.5
You need to read the unbricking thread about this, all the info you need is there.
http://forum.xda-developers.com/showthread.php?t=286755
Click to expand...
Click to collapse
I read everything there and nothing seems to be working for me. I woudnt post for nothing. i dont want to be annoying.
OK im going to repost what ive said on 4wm:
We need to check if your Radio BL is functional, firstly leave HardSPL v7 on there and connect to the bootloader via mtty (il assume you know how to do this).
Issue the following commands and tell us the results please:
1) checkimage (this shows the CRC checksums of each component...id expect the radio image to show a timeout....
2) info 2 (This will verify that your CID is intact)
3) info 8 (does a bad block check)
Once youve done this, flash SPL 1.10.oli to the device and once again connect up to mtty.
4) 'rtask a' this will enter the radio bootloader you will see "Enter Radio Bootloader" or something to that effect
from now on when you type the text does NOT appear on the mtty screen.
5) 'rversion' this should return your radio bootloader version...now unfortunatly if you see nothing...you radio BL is dead and sorry your device is royally bricked. If you get something returned back onto the screen (most probably containing the text '0108') then your radio BL is fine.
Click to expand...
Click to collapse
do as instructed in that text, post your results here.
I cant falsh spl 1.10 oli. it gives me the 260 error.
the 260 error is not connected via USB right? .. weird... have you tried taking your battery out for a couple minutes, then booting into BL mode? sounds weird but this worked for me when I didnt flash hardSPL firsl..
hey mrvanx's
I can't downgrade the hardspl to 1.10, anyhelp.
I cant active sync, the phone doesnt boot up.
Is there anyway to aviod having to respond on the phone.
hey,
i can get the phone to boot up into windows and then it freezes within a couple min. what should i do. Still no gsm message and no phone. thanks
Dan
OK, so let's try and get you to a working state - I've bricked mine a couple of times and it can be quite heart-stopping, eh?
The first thing I would do is re-download radio 1.43, just incase your current one is damaged somehow.
Secondly, download Black Shadow - I know it's not the ROM you ultimately want but the aim here is to get you working again and we can move forward from there.
First, boot up into BootLoader mode (hold down the OK button on the left side of the phone and the power button and then press the reset button on the bottom, just in case you didn't know
You should come to the three colour screen and it should be reading IPL-1.04 and SPL-2.10.Olipro. If it isn't, stop here and post what it does say.
If it everything is OK at this point, when you plug your phone into your computer, it should change to USB at the bottom. Just wait for the Found New Hardware prompts to clear on your PC and then flash the black rom - choose the hardspl option in the flash program.
Once that has finished and it is at the "tap screen to set up windows..." bit, put it back into bootloader mode as above and flash the radio.
This should hopefully give you a running phone again as I know this combination works OK as I am currently using it.
Fingers crossed, don't panic, and let us know what the results are
Cheers,
Smiffy.
Nothing is working, can some please help me. Is there anyt way i can restore the spl to the original one so i can send the phone back, i just got it like 2 weeks ago. thanks
Also i have a bad block thats what i think makes the phone freeze after i boot it up.
How can i get around this, thats seems to be the biggest problem.
Hey everyone, let me give you more info.
I can fully flash any rom and and radio,
phone will boot up like 1 out of 10 times and then freezes and thats it.
i have a bad block number 6. I have hard spl v7 installed before the phone got screwed up. I cant downgrader the spl to a lower one to check if radio stack is screwed up. Can someone please help me, if you need to ask me more info feel free.
I constantly get a communications error, and it never leaves 0% on the status.... No clue on what could be wrong... Anyone have a suggestion? I've looked on all the faqs and didnt see anything else I could try.
ghostyroasty said:
I constantly get a communications error, and it never leaves 0% on the status.... No clue on what could be wrong... Anyone have a suggestion? I've looked on all the faqs and didnt see anything else I could try.
Click to expand...
Click to collapse
That means you didn't successfully unlock.
If you put your phone into bootloader, it needs to say 1.20 Olipro, not 1.10, which it probably does.
Retrace your steps on the unlocking process.
- DogGuy
When I put the phone into the bootloader, it says 110... and I unhook and rehook up the usb cable, and the activesync doesnt detect the titan anymore.
I then use the exitbl program to reboot the device, and then continue once my titan reboots.
Then I get the 262 connection error after the status shows 0% on both the titan and my computer for a while.
Leave your phon ein bootloader mode and run the unlocker. As long as the screen says USB it should work.
ghostyroasty said:
When I put the phone into the bootloader, it says 110... and I unhook and rehook up the usb cable, and the activesync doesnt detect the titan anymore.
I then use the exitbl program to reboot the device, and then continue once my titan reboots.
Then I get the 262 connection error after the status shows 0% on both the titan and my computer for a while.
Click to expand...
Click to collapse
Thats where you went wrong. You aren't done with the unlocker, and *do not* run exitbl until after the RUU has already run. The RUU is actually installing the unlocker, you are just sitting at a temporary bootloader to allow the 1.20's RUU to actually run.
edit:
So, run unlocker, do the disconnect-reconnect when told, when the RUU comes up, you need to follow it all the way through to completion, flash and all, and you'll end at 1.20 Olipro. Then you can finally use the exitbl. If the RUU does not come up, check the directory \TempTytn\ and run the romupdateutility.exe thats in there.
Good luck,
- DogGuy
Thanks DogGuy.. So I run it even if Activesync doesn't show a connection once I unplug and replug the titan???
As long as when you reconnect the usb cable the bootloader itself says USB at the bottom, you're just fine.
- DogGuy
Thanks, I got 1.20 now... So I'm off to try a rom.. Any suggestions? I'm thinking about dcd's version
can someone post instructions to get into bootloader mode? thanks
whoa, DogGuy posting at xda!!!!!
It's DogGuy to the rescue
WOOOOHOOO!!!!
I'm glad I read this first.
I will probably try this over the weekend.
BTW will this work on Vista?
same Problem
I ran into the same problem...
I used a different USB port and either turned activesync on or off... can't remember and did the unlock again. It detected the phone differently on the other port for some odd reason.
wow another one from dcd
With PPCGeeks undergoing their upgrade, where can I download 2.40-olipro from in the mean time? I'm wanting to do some rom upgrades but it seems I need this to unload things for it. I'm trying to install the radio 3.27 and one of the titan 2.x roms with the GPS update.
here u go...
Mod Edit:
Unfortunately the attached file was for an earlier version - see posts below for 2.4
origins81 said:
try hitting search first
Click to expand...
Click to collapse
I did and 2.40 olipro only gave me messages saying that I needed it, not that it was called TitanUnlock. Thanks for the link.
Did I miss somthing?
I downloaded the file and it still said version 1.20Olipro did I miss something?
I saw that it was 1.2 but it didn't register that it was the wrong version and that probably explains the problems I was having trying to load the new rom.
olipro 2.40 here you go
this is the link when ppcgeeks.com comes back up you can get it.
however attached is the file you want and need. BUTTTTTTTTTT
you will now need to find the "re-locker" so you can relock the old olipro and use the new.
Thanks for the file, but I guess if I need to find another program, will wait for either ppcgeeks to come back up or sprint to release the offical rom.
Does anyone have the program for "re-locker"?
Here's the file with the proper name. It's not the easiest to find especially with the other side being down. So without being rude I shall set you in the right direction. Plus if you search for "titan unlocker" as per the other file name you are liable to be loading the OLD unlocker not new since it is generically named such.
edit....
Sorry I guess my interrution while posting this caused me to duplicate someones post....
Thank you for the links. You are far from being rude, but show you understand that all the searching in the world won't help when you don't have the right information and that one of the main supports is missing.
Thank you all for your help! I ended up googling and searching and came upon this post from another board.
"I had the exact same problem.
Connect your phone (while in Windows, not from the bootloader) to your computer and make sure it creates an ActiveSync connection.
Download the file from here: ftp://ppcgeeks:[email protected] . Extract it and it should launch the Titanunlocker.bat. If it doesn't, just launch the batch file from the place you extracted the files. Follow the prompts, and when it's done, you should have 2.40 installed. I too couldn't get 1.20 off, but after I did this, I now have 2.40 bootloader."
----------------
Also if you are stuck with the bootloader screen (rainbow) you can just run titan_exitbl.exe in the file I've included it will allow you to boot. Also you must disable activesync from looking for usb connections if you have to go the titan_exitbl.exe route.
The file listed able will actually attempt to update to 2.40 once you run it, really automated.
Thanks to PDAPhoneHome's jrider for the post.
I was on 1.20, but I didn't have to relock or anything to upgrade to 2.40. I just went onto the bootloader screen, then ran the RUU exe for 2.40 in the TitanUnlocker zip.
Oh boy, uncrackable Apache 6700!
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
Click to expand...
Click to collapse
Dude...this is the Titan forum, not Apache. Why you would try altering your bootloader with unlockers specifically meant for other devices (kaiser & titan) is beyond me.
superlover911 said:
I cannot get the hard SPL to crack!!!! Help!!!
I currently have Bell Mobility 2.13 on my phone. I have installed .NET framework 3.5 on my PC. I have done a hard reset on my 6700. Connected to activesync. I have tried to run kaiser-HardSPLv1, titanunlocker and Hard-SPL-MFG. I my phone locks up before I get to a tri-coloured screen. I disconnect from my PC and reconnect, then the Flash upgrader program starts and my phone turns off by itself and then my PC gives me an connection error. Any ideas?
Click to expand...
Click to collapse
This post shows that people are not worried about what they do to their phone. 911, you need to read the wiki for your phone (APACHE 6700) and do not use any software or roms for other devices (i.e. 6800, Kaiser, Titan, etc) unless you are 100% certain what you are doing. You are really close to hosing your phone.
Read this twice. http://wiki.xda-developers.com/index.php?pagename=HTC_Apache
x64 compatibility?
Am running XP x64 edition and the 2.4 Olipro wasn't working, saying it cannot run in a 64-bit OS.
Any suggestions/solutions? I don't have access to any 32-bit computers.
EDIT: Already resolved elsewhere:
MrTek said:
it is because the sleep4 command is 16bit which is not allowed to to run on 64 bit os
just edit the cmd file in a text editor and replace sleep4 with pause
now it will pause when it runs which means you have to hit enter to continue which should be enough a delay
i just did this exact same thing tonight without issue
Click to expand...
Click to collapse
So I'm a total n00b at unlocking phones but I was trying to unlock my alltel 6800 and after running the program and following the steps I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc. I tried a hard boot/soft etc. and can't find a solution. Also activesync is not recoginizing it. Thanks much for any help.
i believe you have to flash it with a new rom/radio.
download the the newest radio. connect your phone via usb. your screen should be in the tricolor (2.40spl) at this point. run the radio flash.
Download a new rom. do the same as above.
to get to tricolor screen (hold power + camera + press soft reset)
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
=I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc.
Click to expand...
Click to collapse
it IS recognizing the phone being plugged in if it says USB at the bottom, so just flash a new rom/radio and you should be good.
HOLD, Give a little more info please
wilmheath said:
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
Click to expand...
Click to collapse
OK, before it is bricked, tell us the numbers on the rainbow screen, then if it is 1.6 then run the 2.40 olipro, then new ROM, then radio. It is not broken yet, activesync does not like it when the unit is in bootloader mode so it will not show it, but the RUU will work if you just go forward with it and when done it will get you out of bootloader. If you get confused and lost then being an alltel unit you can put the 1.6 bootloader back on, run the stock RUU from utstar.com, bring it back stock and start again.
I got it fixed and installed the sprint firmware but silly me let it run through the setup and now it's trying to use the spring network. Sometimes I wish i could punch myself in the face..
Ok so i got no2chem up and running great but I still can't actually dial out. When i dial it says i'm not allowed to etc after a few rings. Is there some way to change back to the alltel network?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
First of all, you don't relock your phone...you leave 2.4-olipro on it because it's required to boot your phone with this rom on it.
Second, go into activesync settings and make sure usb is enabled in the connections.
get back to Alltel,,,,
wilmheath said:
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
You will need to load up the PRL and then do IOTA.
madman34 said:
You will need to load up the PRL and then do IOTA.
Click to expand...
Click to collapse
I'm sorry but i'm not familiar with those terms. I do have USB enabled on activesync though but it never detects it.
From reading other threads I assumed I had to relock it, then reload the alltel rom to get the radio working again. Is there another way?
I got the factory alltel rom back in and working but it's not letting me make calls still. Any ideas on how to fix this?
Well i got my phone working finally but now the data line is not working. It says I need a password now which I haven't needed before.