Hi to everybody.
I have an Hermes 200 Vodaphone VPA compact 2 v1605.
I wanna put into this pda the latest Schap's 4.31 ROM.
I have done the mrVanx procedure and I have successfully installed the 2.10 Hard-SPL-V7.
Now I wiil explain my two problems:
- I don't know if my pda is CID unlocked or not... With the HardSpl flashed on my pda, should I be scared about that or not?
I think HardSPL turn my pda into supercid... right?
- If ROM flashing procedure will be stopped by a pc crash, I can unbrick my pda easily? In wich way?
Should I use the mrVanx guide to flash pda or I follow microsd guide?
Many thanks
I should have read the wiki. Either way, and since nobody helped me when i needed and i had to find it all by myself, i know how frustrating it might be. So ill give u hand.
First go here:
http://forum.xda-developers.com/showthread.php?t=293665
Download that tool that will superCID ur phone and Hard SPL it automatically. Pay attention to every step.
After that, and since the hard spl installed by that tool is rather old, go here:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
In the middle of that tuturial u will find the link to the mostly used version of hard spl and how to update ur rom to one of the cooked ones around here.
Soz if my english aint perfect but im not english nor american though.^^
Thanx for reply. But i think you haven't understand my question.
I think my pda is already SuperCID because i have installed the 2.10 HardSPL.
Somewhere in this forum or in the wiki i found that if I flash my pda with 2.10 HardSPL I don't have to use unlocker because this version allow SUPERCID mode.
Am I wrong???
My pda is also already sim unlocked. Infact it is Vodofane (english or german) but i can use TIM italian sim card without problems.
Now my question is:
If I write the schap's ROM with SD procedure, should I scared about RADIO ROM damage?
I found that schap's ROM doesn't modify RADIO, right?
..so i think that SD procedure is the safer way.
Thanks
Not really, most if not all cooked roms DON'T have the radio rom cooked in as there is no perfect rom for everyone, its carrier compliant. Just because a new radio rom comes out doesn't mean its going to improve your reception or battery life, sometimes it causes problems, hence the chefs give you the option of what radio to use.
Now, Hard SPL is only a safety net, things can still go wrong but if they do there is a load of information on how to fix it, ESPECIALLY if you've installed Hard SPL. Make sure its version 7 so the spl reads as 2.10 olipro when you enter bootloader (power button, ok button above flywheel and reset with stylus, hold in until you get to tricolour screen). Just soft reset with stylus to get out.
Personally, as you have Hard SPL, I'd use the sd card method to flash your os. Its on the forum MANY times over. A quick search should find it. VERY EASY and, I believe, safer than using the pc. Just make sure the battery is charged.
Hope this helps....
Cheers....
sfrangebob said:
Hi to everybody.
I have an Hermes 200 Vodaphone VPA compact 2 v1605.
I wanna put into this pda the latest Schap's 4.31 ROM.
I have done the mrVanx procedure and I have successfully installed the 2.10 Hard-SPL-V7.
Now I wiil explain my two problems:
- I don't know if my pda is CID unlocked or not... With the HardSpl flashed on my pda, should I be scared about that or not?
I think HardSPL turn my pda into supercid... right?
- If ROM flashing procedure will be stopped by a pc crash, I can unbrick my pda easily? In wich way?
Should I use the mrVanx guide to flash pda or I follow microsd guide?
Many thanks
Click to expand...
Click to collapse
The guide on MrVanx page does not have the images. Is thare a copy of it somewhere with the full ilustrations?
Thanks.
Yes i have HardSPL v7 2.10 installed on my pda.
This mean I'm in supercid mode and I'm able to flash any rom. right?
I haven't to use the sim cid unlcker, right?
I haven't understand this:
At the moment I don't want to change my RADIO ROM.
Latest schap's ROM doesn't modify RADIO so my radio ROM remain the same. Is this true?
If I flash schap's ROM should I to flash a RADIO ROM that works with schap's one? Or does my RADIO continue to work?
sfrangebob said:
Thanks.
Yes i have HardSPL v7 2.10 installed on my pda.
This mean I'm in supercid mode and I'm able to flash any rom. right?
I haven't to use the sim cid unlcker, right?
I haven't understand this:
At the moment I don't want to change my RADIO ROM.
Latest schap's ROM doesn't modify RADIO so my radio ROM remain the same. Is this true?
If I flash schap's ROM should I to flash a RADIO ROM that works with schap's one? Or does my RADIO continue to work?
Click to expand...
Click to collapse
I have a brand new hermes since last week and i passed a lot of blocking and stucking in the bootloader. However, the first ROM i installed was Schaps one and on that time i didn't even have my phone Hard SPL'ed or SuperCID'ed! I used that tool of SSPL. But if u say ur phone is already Hard SPL you will have no problems installing the schaps rom. In addition, the RADIO ROM will not be modified with his rom. I must say that besides his ROM was installed perfectly, there are some other cooked ROMs that require your phone to be SuperCID'ed.
Thanks for your reply.
the RADIO ROM will not be modified with his rom
Click to expand...
Click to collapse
Is this a good thing or bad one?
I mean: my pda now has no problem about RADIO and I don't want to change nothing about RADIO ROM.
If i flash schap's ROM the pda continue to work well with my RADIO? or the schap's ROM work well with some RADIO ROM an bad with other.
Thanks
You won't change your radio rom and yes it will still work with ANY rom you use (as long as its for the Hermes).
ok!!!
Now it's time to flash.
Thanks a lot!!
good flash^^
Zero|Cool said:
good flash^^
Click to expand...
Click to collapse
Thanks.
In your signature i found that you use a CRC's ROM.
Also crc's rom doesn't modify RADIO and can work well on my pda?
sfrangebob said:
Thanks.
In your signature i found that you use a CRC's ROM.
Also crc's rom doesn't modify RADIO and can work well on my pda?
Click to expand...
Click to collapse
It works good on mine. And no, it doesnt modify your ROM.
As stated before, the chefs tend to let YOU decide what radio to use... There is no perfect radio rom and location/carrier seems to determine what is the best radio for you.
Cheers...
I put the rom in microsd renamed in HERMIMG.nbh
I start the bootloader withe ok + power + stylus but the flash procedure doesn't start. I have only the bootloader screen with 4 rows:
RED HERM200
IPL-1.04
HERM200
SPL-2.10 OLIPRO
GREEN
BLUE
WHITE SERIAL
what's the matter?
p.s.
I'm using a 2g sandisk
with 1gb microsd sandisk it works!!
Flash successfull!!
Thanks to everybody
sfrangebob, it should work with a 2gb too, It needs to formatted fat32 though.
Congrats and welcome to the wide world of Phone upgrading...
DISCLAIMER - Phone flashing can be addictive....
I know.. I formatted it many times but the flashing operation doesn't start.
With 1 gb it starts on the first attempt.
ahah flash addciction
Related
What I have now:
OS: Black 2.0 Cingular edition
Boot Loader: 1.01
Radio BL: 108
Radio: 1.38.10
what I want:
OS: WM 5 from the 1.34 cingular release
Boot Loader: Loader from the 1.34 cingular release
Radio BL: AFAIK you can't downgrade these so staying at 108
Radio: 1.16.00.00
How I plan to get there:
take the .nbh form the 1.34 cingular package and use RUU to flash the device.
Questions and concersion:
I'm looking for input on possible incompatabilities and hang-ups with varios BL versions and what not.
comments / feedback on my plan would be greatly appreciated and I will build a monument in your name if you help .
This has been covered before...
But, since you're well on your way to brick-ville, I'll buy your phone off you for, say, $100? It'll be worth less after you brick it...
Read up on the W*I*K*I and Oli's 1.40.Olipro bootloader before you do something dumb.
I did read it.
And thats the plan I came up with.
I was looking more for a confirmation.
The wiki has a ton of great info but its laid out reall crappy and not very cohesive. So I figured I'd post what I've came up with after reading it to see if I missed something. And from there maybe get more specific input on where the issues/dependencies are..... or maybe not.
spicer said:
I did read it.
And thats the plan I came up with.
I was looking more for a confirmation.
The wiki has a ton of great info but its laid out reall crappy and not very cohesive. So I figured I'd post what I've came up with after reading it to see if I missed something. And from there maybe get more specific input on where the issues/dependencies are..... or maybe not.
Click to expand...
Click to collapse
From your plan it is obvious that, even IF you read the wiki, you didn't understand it. Re-read the THREADS about 1.40 SPL and also search for MRVANX and read his TUTORIALS...
---New plan
What I have now:
OS: Black 2.0 Cingular edition
Boot Loader: 1.01
Radio BL: 108
Radio: 1.38.10
what I want:
OS: WM 5 from the 1.34 cingular release
Boot Loader: Loader from the 1.34 cingular release
Radio BL: AFAIK you can't downgrade these so staying at 108
Radio: 1.16.00.00
How I plan to get there:
Flash to hardSPL-v6
Fash Radio to 1.16
flash OS i get out of the 1.134 package. (the os.nb file i believe it is named)
last flash the boot loader.
Questions and concersion:
I'm looking for input on possible incompatabilities and hang-ups with varios BL versions and what not.
comments / feedback on my plan would be greatly appreciated and I will build a monument in your name if you help .
LegolasTheElf said:
From your plan it is obvious that, even IF you read the wiki, you didn't understand it. Re-read the THREADS about 1.40 SPL and also search for MRVANX and read his TUTORIALS...
Click to expand...
Click to collapse
I really appreciate the feedback. At least you're letting me know my plan wont work. Which will prevent me from trying it. But it would be kick ass if you could be more specific about what in the wiki i missed like :
-you can't flash the entire .nbh file cause it will try to replace your boot load and break it.
or
- Re-read the THREADS about 1.40 SPL because *something useful here*
Either way I'm still thankful cause I know my plan is a **** sandwich.
Very good.. You're getting there! It's nice to see someone read some directions..
You have it mostly right.. Flash the HardSPLv6 first. Then, grab the .nbh from the cingular rom and combine it with CustomRUU. Choose 'Autodetect' (we're looking for a hard-spl flash)..
Then, once that's done, you'll have the right radio, OS, splash, etc.. The only thing left would be to down-grade the bootloader, which I would advise against.. But, you can do it.. There is a seperate thread on HOW to do that, as it isn't just a one-step process.. Search and ye shall find.
Thank MAn!!! That kicks ass.
I need to send my phone back because the radio dies every 5 mintes.
So I want to get it as close to factory as possible.
So after I downgrade the BL i won't be doing anymore flashing to that phone.
Sometimes when I soft reset the phone is says "No GSM" even when sim is there. Soft reset it again and the radio is detected.
Very irritating.
Check out:
http://www.mrvanx.org/hermes_guide/
Flash HardSPL-1.40
Create NBH containing your provider's 2xSplashScreen + ExtROM + OS & flash it
Flash 1.16 radio
Flash-HardSPL-1.10
Flash your original IPL & SPL versions.
F-ya! That last part about down grading the BL is the part I was having trouble pinning down.
One last question:
Can I use the cingular NBH or will it try to flash the RBL and crash because you can't down grade the RBL
the the new mrvanx page is dope. found the donwgrade guide.
Bricked using this method
pof said:
Flash HardSPL-1.40
Create NBH containing your provider's 2xSplashScreen + ExtROM + OS & flash it
Flash 1.16 radio
Flash-HardSPL-1.10
Flash your original IPL & SPL versions.
Click to expand...
Click to collapse
Pof,
I did it this way but after flashing the radio rom I get no GSM and then I'm stuck in the Windows Mobile Screen.
I have looked in the Wiki but how can I actually unbrick?
My SPL is still 1.40 Oli. But I can't get activesync to work.
Should I flash the new radio via SD card or any other way (mtty?)
I would be very gratefull for any help,
Cheers,
HJ
P.S. Found a solution; http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
I will try to do this trick.
Thanks
@hellejoep: Try flashing your latest working radio again in NBH format.
pof said:
@hellejoep: Try flashing your latest working radio again in NBH format.
Click to expand...
Click to collapse
Pof,
One question, Can I upgrade radio rom via mtty?
Or otherwise?
Cheers,
HJ
P.S. How can I Flash any radio in NBH format? While stuck in bootloader?
hellejoep said:
Can I upgrade radio rom via mtty?
Click to expand...
Click to collapse
no
hellejoep said:
How can I Flash any radio in NBH format? While stuck in bootloader?
Click to expand...
Click to collapse
Disable activesync, and use CustomRUU.
pof said:
Disable activesync, and use CustomRUU.
Click to expand...
Click to collapse
Done that but then I get a Error 260.....
Any suggestions?
Or is there a way to bypass this? I have IPL 1.01 and SPL 1.40 Olipro.
I now got a Connection Error 264 but the bootloader gives usb and I can reach the hermes bij MTTY.exe.....
What is going wrong?
@hellejoep: close all programs including mtty before u run ruuwraper. Make sure you're using the latest version (v4.2) and activesync is not enabled.
pof said:
@hellejoep: close all programs including mtty before u run ruuwraper. Make sure you're using the latest version (v4.2) and activesync is not enabled.
Click to expand...
Click to collapse
It worked, cheers!!!!!
LegolasTheElf said:
Very good.. You're getting there! It's nice to see someone read some directions..
You have it mostly right.. Flash the HardSPLv6 first. Then, grab the .nbh from the cingular rom and combine it with CustomRUU. Choose 'Autodetect' (we're looking for a hard-spl flash)..
Then, once that's done, you'll have the right radio, OS, splash, etc.. The only thing left would be to down-grade the bootloader, which I would advise against.. But, you can do it.. There is a seperate thread on HOW to do that, as it isn't just a one-step process.. Search and ye shall find.
Click to expand...
Click to collapse
@LegolasTheElf,
This was great example on how to get people to read the wiki. I like your approach and I will try to use it in the future.
hi all,
i've just bought a t-mobile vario 2
i;ve read the wiki & a few of the posts regarding upgrading
but to be honest it has so much information & sometimes the information is contradictory.. so it gets confusing
i've been using the uni for a year now
my point is
i want 2 upgrade my hermes 2 wm6
my boot screen says
herm300
IPL-1.01
SPL 1.40.Olipro
i can use a different/other sim card than t-mobile
how do i chek if my hermes is CID unlocked
and what radio i'm using & what's my bootloader number??
i try 2 read the splash screen after soft reset but the radio version goes away pretty fast
do i run POF's unlocker v3a? is it safe to run again, even if my phone is cid unlocked?
in order 2 upgrade 2 wm6
do i need to install olipros hard spl 2.10? and then run customruu?
this is what i mean by confusing?
i've upgraded my magician, uni & wizard
however they all had pretty easy/self explanatory directions?
i'm sorry for sounding like a noob, but its new territory....
thanx in advance
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
chrisjasper said:
Is there a specific reason you want to CID the device? T-Mobile's data plan s pretty great so I have never seen the need to use another sim in my vario. You dont need to CID unlock to upgrade the rom.
As long as you have installed Olipro's spl to protect against bricking your phone it should be fairly safe to install a wm6 rom. If not, definitely install the current version of hard spl.
Once you have installed SPL, you then run the RUU.exe file that usually comes with the rom. Tha majority will have a tick box on the first page that says auto detect, which will check which version of spl you have installed and then run itself accordingly. It is best to have the current hardspl installed though.
Most of them dont touch your extended rom and only replace the OS rom contents. T-Mob's wm5 extended rom customizations wont work with wm6 anyway so you will need to go looking here for a cab file called (I Believe) tmobileukfixed.cab.
You will also need to look for newer versions of your pocket pc software as some older ones dont play nice with WM6.
Good luck, and if in doubt, read MrVanx's upgrade guide here: http://www.mrvanx.org/cms/
Click to expand...
Click to collapse
i dont live in the uK
so the tmobile plan is not the usp
i need to unlock the extende rom as i like 2 install most of my progs on the extended rom and also my ringtones as the sd card takes a cople of seconds b4 it kicks in..
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
todd_jg said:
check the wiki under Bootloader information.
Using mtty, there is a command to check CID status.
Click to expand...
Click to collapse
hi
i've managed 2 find out that my phones supercid
however i cant get mtty 2 work
i put the phone in bootloader
then i conect the phone via usb
when i rum mtty
it says usb port cannot open
i tried mtty 1.42 as well.....
Is there a way I can unlock my hermes whilst keeping the newest radio (1.54.00.10)?
Yes, load hard spl ver.7 on then pick a rom, any rom that doesnt upgrade the radio rom. Most cooked roms don't have the radio cooked in. Happy upgrading.
ultramag69 said:
Yes, load hard spl ver.7 on then pick a rom, any rom that doesnt upgrade the radio rom. Most cooked roms don't have the radio cooked in. Happy upgrading.
Click to expand...
Click to collapse
VERY incorrect reply.
@ TheOracle
The radio version used in pofs unlocker has been modified to allow CID/SIM unlocking so you must use the package provided in the thread there.
I can't seem to find the thread, I'll keep looking though I'm probably being stupid! Thanks for the help =D
Well I've just unlocked the phone again with CID-Unlock V3a, however it's stuck me with Radio 1.16 . Could I still use Herm_Unlock_v3 etc with the newest radio or will it brick if I don't use Radio 1.16?
Here are the steps needed
1 Download and unzip the unlocker. All of the instructions are included on the zip file. Follow it closely. Read the thread for instructions and common mistakes before you do it. The program will install radio 1.16 which you'll replace with step number 3
http://forum.xda-developers.com/showthread.php?t=293665
2. Install hardspl. Use this guide by mrvanx. Very straightforward. Use a computer with xp, avoid vista.
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27
3. Download your radio rom here and install.
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Go back to mrvanx guide on installing radios. Read all the threads and understand what is needed for each step to safely upgrade your device. If you're not sure, it's better to ask again on this thread. I hope this helps and good luck
Also, I think you can ask where you bought the phone to get an unlock code? I know at&t will do it with conditions.
TheOracle said:
Well I've just unlocked the phone again with CID-Unlock V3a, however it's stuck me with Radio 1.16 . Could I still use Herm_Unlock_v3 etc with the newest radio or will it brick if I don't use Radio 1.16?
Click to expand...
Click to collapse
I always unlock using the manual method, so for the last step I transfer HERM_Unlock_v3.exe to my device and run it. Click the unlock button, then select sim and super cid unlock.
Follow the steps I've provided, you should be fine
For future reference, here's mrvanx's hermes guide.
http://forum.xda-developers.com/showthread.php?t=299462
If you decide to upgrade your rom as well, the guide will be a great help.
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Da_G said:
Possible image might be corrupt on sd card, grey screen is shown when it's trying to read sd, have you tried with sd removed? if you get to 2nd tricolor screen with sd removed i would use usb flash to restore it to working order..
Click to expand...
Click to collapse
Removed the SD and it stays at the tricolor screen with the spl version as mentioned in 1st post.
Also, displaying the Upgrade ROM code error, please try again message
The mode is currently serial
What can I do from here?
fireblade63 said:
Dear all,
I am facing a problem here.
Had a hardware problem with the built in microphone and had to revert back to stock rom/splash screen/Original SPL in that order.
Had no problems reverting the ROM and the original screen back (just a couple of flashes), BUT when I tried to revert back the stock SPL here http://forum.xda-developers.com/attachment.php?attachmentid=110582&d=1220406410
I renamed the file to RAPHIMG.nbh, copied it to the root of the SD Card and entered bootloader mode and this is what it displays:
RAPH100
SPL-1.90.0000 (Which means a successful flash)
!!! AND THEN THIS !!!
"Upgrade ROM code error"
"Please try again"
This message is located in the last part of the green stripe in the tri color screen (bootloader)
It is then followed by the grey screen automatically which you are supposed to press volume key to start a flash process BUT it just HANGS at Loading...
unabling you to flash anything.
It's actually a friend's phone too so I guess you understand how hard it is....
Any help is appreciated
Thanks in advance
Click to expand...
Click to collapse
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
NotATreoFan said:
You cannot flash an SPL from the bootloader. You need to use SSPL. The directions can be found in the HardSPL thread.
Click to expand...
Click to collapse
Hey man, thx for stopping by..
If I understand correctly, SSPL runs through the device which is stuck at bootloader currently... or am I hopefully wrong??
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Da_G said:
If you're at the tricolor screen and it reads serial, that should be fine.. plug in usb and it should switch to usb.. then flash a stock carrier rom through usb.. that should get you up and running and you can then run sspl and flash your spl
Click to expand...
Click to collapse
Keep in mind im currently on stock SPL, do u think flashing the stock ROM is ok?
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
dude....i hate to say this...butyou might be s.o.l. at this point. i did the same to my fuze not too long ago... tryingto flash anything to the phone just locks it up.i was lucky enough to bs my way through an att guy to get me a new one (was still under the 30 day warranty).
Da_G said:
That's exactly why i suggested stock ROM, stock SPL will only accept stock ROM's (it will overwrite the spl too so make sure the stock rom you are using is the right one)
Click to expand...
Click to collapse
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
I had the same problem as you and could not flash any rom, Always get Invalid vendor ID.
You need the right Stock Rom to flash and in my case in the middleeast, the Stock Rom is so far only available in at HTC.
I had to take the phone to HTC Service Center and they flashed the correct Stock Rom and charged me as they did it out of warranty.
Regards
fireblade63 said:
That's wt Im trying now, tried to flash 2 ROMs already and stops at 2% saying Invalid Vendor ID
I gess I'm using wrong shipped roms till now
Click to expand...
Click to collapse
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
fireblade63 said:
Hmm, then I need to know from which ROM the SPL originated and then flash it.
Thing is, some of the shipped roms available at wiki are just nbh files..
I tried flashing with the wrapper exe and the RaphaelCustomRUU.exe and still all roms I've downloaded don't seem to work.
It's a RAPH100 untied to a network.
Click to expand...
Click to collapse
Post in the HardSPL thread asking which ROM the SPL originated from. Once you know that, you can download the appropriate ROM from the Wiki.
NotATreoFan said:
Sorry about my last post... I misread your issue.
If you flashed the stock 1.90 SPL from the HardSPL thread, then you will need to ask Olipro (or cmonex) which WWE ROM it originated from. That ROM is the ONLY one your phone will accept.
The steps in reverting SPL for warranty / return state to always do the ROM first so that you do not run into this problem. I had the same issue when I was testing a US 3G Diamond I bought from Best Buy (to become acclimated to TF3D prior to the Fuze's release). I restored the SPL first, and then couldn't get Dutty's ROM off the phone, because I could not locate a downloadable version of the WWE ROM that phone came with. [Luckily, Best Buy Mobile's employees in KOP, PA aren't too clever, and I was able to convince them that the phone came that way. ]
Click to expand...
Click to collapse
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
shafez said:
SPL has nothing to do with the Invalid Vendor ID Error, It is the CID. In another word you can flash SPL 1.95 and still can not flash the AT Rom 1.95.502.5 because the CID is different.
Regards
Click to expand...
Click to collapse
The CID is determind by the SPL.
Look up the error code posted... everything points to HardSPL. Back in my Wizard days, HardSPL did not exist, and we just did a CID unlocking. This is not the case with newer devices.
All ROMs are not created equal. Each WWE ROM checks for specific information within the SPL, and if it doesn't find what it's expecting, fail...
stepw said:
ViperBJK's QMAT features GoldCard generator for current HTC devices that can force RUU to bypass CID check.
Do you know what is the CID of your device?
Click to expand...
Click to collapse
I'm not sure
Where can I know that?
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
fireblade63 said:
@NotATreoFan && Shafez,
I remember from TyTNII day when Shafez suggested extracting 3.29 and 28 SPLs from the newer shipped 6.1's for a better responsive device.
We could extract and build with htc rom tool if I remember the name of the tool correctly.
Do we have a tool as such compatible with TP? (agreeing with NotATreoFan here)
@Shafez,
Since you think it is not SPL and it is a CID issue, what can I do about it?
Sending it to SVC for repair out of warranty is an option but I'd like to leave it as my last.
Did they provide the ROM or they flashed it for you?
Were u able to make raw files out of it for future use or any1 else has it?
Thx guys and keep the help coming
Click to expand...
Click to collapse
Since you cannot get past the bootloader, your only option is to find the WWE ROM that matches the SPL you flashed. Even though the HTC ROM Tool "signs" the NBH file, it still won't fool the stock bootloader... if it did, we wouldn't need HardSPL.
can somebody please help me, I have flashed 5 different ROM's to my vodafone HD2 and have encountered a varying degree of problems with each one. I would very much like somebody to tell me where I can get a Stock ROM not locked to any carrier so I can reflash my pretty usless fone or indeed to help direct me to a stable cooked ROM that would allow my fone to work again.
Thanks is advance.
P.s - my first post so please be gently, also the last 3 I have tried are Artemis ROM's with no sucessful outcomes.
peeko1979 said:
[Q] htc hd2 stock rom 6.5.3
Click to expand...
Click to collapse
there is no stock rom that is 6.5.x They are all 6.5
Not sure what you mean by stock rom not locked to a carrier, , do you mean a non branded rom (the ones marked HTC WWE, look HERE or in the various threads in the rom development section.) or do you mean you want to unlock your phone to use any network? in which case no amount of any kind of flashing will do that. Ask voda for a code, or buy one online.
Sounds to me like you need to return all the way to stock and start over. Get any of the voda roms from that link above (theyre marked vodaphone, you cant miss em, theres a 1,43 one, a 1.66 one ((if you're a brit)) or 1.72 if you have a european language voda.
Get that, and either
1 - remove hspl by running hspl.exe and choosing 1.66.0000
then
2 - run the downloaded rom.exe and flash over usb
or
1 - extract ruu_signed.nbh from the rom.exe you downloaded,(look it up if you dont know how) copy it to a formatted fat32 sd card smaller than 8gb, and rename it leoimg.nbh then start the phone into bootloader and it will ask you if you want to flash.
that way you are back to teh start, and you can apply hspl and start again.
(For people reading this thinking 'he didnt say do a task29',, its my understanding that using the official .exe to flash the rom does a task 29 anyway, and its been edited out of customruu.exe so it can be used to flash radios without wiping the rom,,,correct? yes no?)
I try 6 Rom but noone will work fine
Vodafone rom 1.72
I am not looking to unlock the fone, simply find a Rom that is 6.5.3 that is stable. I have just flashed back to voda 1.72 but that is 6.5, im fussy and don't like the start button at the top. I'm in scotland so need something that will work here ok on vodafone.
I was hoping to find a rom that had not been altered and as such an original (Stock) ROM.
your help is much appreciated.
There are no such stock roms for the HD2. If you want to flash a stable rom in the style you like (start button at the bottom) then you will need to HSPL (search the forum) your phone and I suggest you start with Dutty's rom. It's very stable and as close to stock as can be. You can always flash back to an original rom for warranty reasons if you need to.
tnx, trying one now. fingers crossed.
ok, just flashed one of duttys roms but now my phone will not boot, it turns on and stays at the htc splash screen. Wont turn off have to pull out the battery. If it will not boot how can I re-flash it? Any suggestions?
did you flash hspl? you will also need the newer radio 2.15.50_04
Quote from Dutty's first page:
Things to Know how about my ROMs:
* HSPL 1.66 Minimum required
* New Radio 2.15.50.04 can be flashed here:
http://forum.xda-developers.com/showthread.php?t=801252
* :Added XDA UC_NET_v0.94 for Auto install see here for instructions:
Thanks to ahirshfield for recommeding it and serfer222 for great work.
http://forum.xda-developers.com/showthread.php?t=709557
* :HSPL 1.66 Minimun recommended
* :Radio 2.10 / 2.11 / 2.12 / 2.14 / 2.15 NEEDED for ROM
* :No Radio version is included in these releases:
* :Correct radio needed to enabled 576 ram for NON-T-Mous HD2 users.
* HD2 Radios can be found here:
http://htcpedia.com/forum/showthread.php?t=2199
I hope you did some reading before you flashed!!
Put your phone into bootloader by holding the vol down side key and use a pen to push the little reset button when the back cover is removed. You should get a tri colour screen which shows you the hspl version you have. If you do this you can flash the correct radio which is probably why the phone will not boot.
all I have done previously is downloaded .nbh files and used SSPL_RUU.exe to flash and they have all flashed sucessfully, but with the after effects of either connection problems or freezing issues.
I have managed to re-flash to the vodafone 1.72 software so at least it is working again, this is not by any means where my talents lie. im a hardware guy, not software, so finding this all a bit confusing. I may just go with the artemis v33 rom which seemed to work the best apart from occassion signal dropouts.
Just out of curiosity - which hspl and radio are you using?
in the settings it says radio 2.07.51.22-2 and i believe the hspl was 1.42
just checked bootloader, spl 1.66
peeko1979 said:
just checked bootloader, spl 1.66
Click to expand...
Click to collapse
If you are sure it's SPL, than your problems are normal sir. To be able to flash custom ROM you need HSPL ex (1.66 HSPL)
is there another way to check other than in bootloader?
peeko1979 said:
is there another way to check other than in bootloader?
Click to expand...
Click to collapse
No sir only bootloader.
I have just re-flashed v33 artemis, so will stick with that, might look at updatin radio version tho. all help much appreciated but must away now as wokring in 5 hours.