DIY Helmet Bluetooth to Wing Ideas? - Wing, P4350 Accessories

Hi everyone, I am looking for Ideas on how to build speakers and a microphone into a full faced motorcycle helmet that communicates with my Wing (in stereo) via Bluetooth. I know there are commercial solutions but for the most part they are crap and a good setups (chatterbox) will cost in excess of $400. So I figure with the right guidance I could make a good system for a fraction of that $400.
What I’m thinking: (of course cheap is the slogan of the day)
1. Bluetooth adapter that will pair with my Wing and receive a stereo signal.
2. Noise canceling microphone
3. Decent (yet thin) speakers
The real question:
Would it be possible to strip apart a Bluetooth adapter and solder in speakers and mic. Allowing me to listen to music on my Wing while riding my bike. I would also like to be able to verbally answer and dial the wing with this setup. One of the big stumbling block is how to power the speakers (would an BT adapter have enough juice?), easily recharge (or replace batteries) in the adapter, and make pairing painless.
I would appreciate any ideas and comments you have. Thanks

Hello and Welcome to the forum!
But if you want to make some speakers in your helmet, Contact the police first and ask if it's legal.
I know a mate who has done that before and when he got a speeding ticket, the officers saw there were speakers.
He got a ticket for that aswell because it may inflect the safety and durability of the helmet.. LOL
Anyway, If i were you i just bought the original HTC headset wich is wired, and plug them in my ears.
Put on your helmet and you can call and such.
But maybe other people will have some other thoughts.

You think the mic will work in that enviroment?

ermm, well if you have a noise canceling mic than it should be no problem.
But i did some research for you and there are helmets availible with a bluetooth headset built-in. Connect your phone with that headset and play some music.

I've been looking to do the same thing. Its REALLY hard to get my helmet on with a bluetooth headset in my ear, its hurts as a matter of fact. I have to take some of the padding out from the helmet if I dont want pain, but thats just not worth the safety risk; I bought a $500 helmet for a reason. Lol.
The mic wouldnt even have to be noise canceling IF you kept the mic behind the chin wind gaurd or inside the helmet somehow.

I totally understand, I paid $700 for an Arai helmet for a reason and its not because of the *****en graphics. What I have started to do…
I have a set of Skull Candy headphones that I removed the speakers from that will fit nicely into my helmet and have great sound. I did a test and spliced the speakers in to the USB headphone adapter (stock) for my wing. I ran into my first problem…. The wing doesn’t have enough poop to drive the speakers. So I will need to use some kind of speaker amp. I found a cheap ($8 + shipping) and small amp on Ebay ( http://cgi.ebay.com/ws/eBayISAPI.dl...STRK:MEWA:IT&viewitem=&item=260255057258&rd=1 )
So I’m thinking that if I can find a cheap Bluetooth (stereo and voice command capable) I could crack it open cut out the original speaker wires and solder in wires to connect to the head set amp. The head set amp looks small enough that I should be able to hide it someplace in the padding of my helmet. Then solder in wires to run from the amp to the speakers and finally mount the Bluetooth on the face guard infront of were my mouth would be.
What I am stumbling with is power. I need to figure out how to make the Bluetooth easy to charge and how to power the amp (requires 1 AAA battery). I would need to make the amp easily accessible to change out the battery which seems like a pain in the ass and may look ugly. What I would really like to do is have a common power source for both device so when I am home I just plug in one cord to the helmet. But I don’t know if that is even possible.
I really want to make this work but in the end this all needs to be functional and CLEAN. I don’t want it to look like I Forest Gumped my way though this project.

You might look at a tactical throat mic and a in-helmet speaker setup from midland. You could also try a in ear tube type setup from Midland also. Both products are for their GMRS radios, but I think with some modification you coud get it to talk to a bluetooth device.
Also you might look at Fire/police communication sights as some departments use bluetooth adapters with their 2 way radios for hands-free mic's that don't have to be connected to the radios.
Let me know if you ever come up with anything, this sounds like a very interesting project....
BG

Related

2.5mm Headset

Does anyone know if one can use any 2.5mm earplug handsfree with the XDA Mini S? The one supplied is difficult to carry lots of wires, would like to have a monaural one. Has anyone tried any? Kindly let me know. Thanks.
I have been looking for the same earphone since i bought the item on JAN06, till now I still cant find a compatible one.
That will be helpful if anyone know which is the best headphone with microphone.Not the Bluetooth one!
Thanks!
ebay Adapter eventually works
Hi there,
I was also looking for a good headset fromt he beginning on, the issue might be solved if I can install the A2DP software (will try later), but a nice wired headset would still be nice.
My favorite would be the ones SonyEricsson is shipping with the music phones.
I actually tested a 2.5mm adapter with cord and speakerpice (with clip) plus adapter for 3,5mm, which would be perfect. One was for Nokia, one for Motorola - both are NOT compatible with the HTCs!
Lately I saw a shop selling the same adapter specifically for HTC devices, so the problem might be solved.
Also I saw 2 wired 2,5mm stereo headsets from Jabra on the US website, they are for sale there but NOT in Europe. If these would work, they would for sure be of very good quality.
Anyone tested these?
Found one
I found one listed on Ebay under HTC Wizard. Its item number 9716253639, seller's name is 5starcommunication. Looks quite cool and they will mail it world wide. Will take sometime before it reaches India. But if anyone in the US orders and tries do let us know. Thanks.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=9716253639&rd=1&sspagename=STRK:MEWA:IT&rd=1
I bought a 2.5mm to 3.5mm adapter from Expansys UK and it works just fine. Sorry - no part number on me, but it should be easy to find on their web site.
Hope this helps
bloney said:
I bought a 2.5mm to 3.5mm adapter from Expansys UK and it works just fine. Sorry - no part number on me, but it should be easy to find on their web site.
Hope this helps
Click to expand...
Click to collapse
Are you able to work with the MIC?
waiho said:
bloney said:
I bought a 2.5mm to 3.5mm adapter from Expansys UK and it works just fine. Sorry - no part number on me, but it should be easy to find on their web site.
Hope this helps
Click to expand...
Click to collapse
Are you able to work with the MIC?
Click to expand...
Click to collapse
I use it for headphones only (senheiser PX200 which sound great with the Wizard!), so not sure if they have mic connected or not. Sorry.
Get the adapter at radioshack.. there r tons n tons of them for $3.. i got one n it works like charm..
with/out mic
I wonder if the ones from Radioshack have a mic in the wire?
I have an adapter 2,5 to 3,5mm with GREAT sound quality, however without microphone in the adapter, thus I always need to unplug the adapter and take off the headphones to answer a call - sucks!
As mentioned so far i Only saw one adapter on ebay WITH a microphone in the adapter piece (and clip on the back) - but do not know how it performs...
http://cgi.ebay.de/XDA-Mini-MDA-Com...06652399QQcategoryZ123195QQrdZ1QQcmdZViewItem
You could also try this one ...
Handsfree and Headphone Adapter
Still no earpiece...
Sigh... still no proper in ear headset (monaural) in sight... :?
2.5 mm to 3.5 mm adapters at Radio Shack
Beware of the Radio Shack adapters. They stick out and are easy to catch on a doorway as you walk through it. I did so a few weeks ago and the headphone jack no longer worked. The adapter male end bent back and damaged the phone female socket. The result was very quiet sound from the headphone jack, totally unusable for phone or music.
I sent the phone back to T-Mobile and they very kindly sent me a replacement. I bought a new Radio Shack 2.5mm male to 3.5 mm female adapter and the same day proceeded to catch it on another doorway, bending back the male plug, and damaging the phone female headphone jack. No sound again from the headphone jack. I will stay away from the headphone adapters from now on.
Phone speaker not working after using headphones - No sound
I had a similar problem (not the same). After using a 2.5 to 3.5 mm adapter my phone speakers and the mic didn't work anymore. I was about to send the device in, when I read about a solution (I think it was in XDA-Dev somewhere).
You'll have to gently move the headphone jack forward and back, twisting it a litte or even better use some compressed air blowing into the jack. It works best, if you to take out the battery and blow from the back.
My speakers work again, but the same thing happens now and then. It seems there is some switch inside the headphone/mic jack, which doesn't go back. That only happens when I use the adapter.
I realize that this is an old thread, but here is an idea for you. As far as I know, pretty much any 2.5mm headset should work. I don't use it for my phone personally, but I recently purchased a Plantronics Gamecon X20 headset for my Xbox 360 after my old one broke. Since it has a plain 2.5mm jack on the end, I thought I would plug it into my phone to see how well it worked. The answer, pretty well apparently. My wife said that it was really clear and, likewise, she sounded really clear on my end. It's going to be a little larger than the ones that have the mic hanging down inline with the wire, but on the other hand, since it's a boom mic the sound quality should be superior with less noise. I haven't tried it for listening to music so I can't vouch for the quality there, but since you are wanting a monaural headset I rather doubt that is relevant anyways. The headset was only $20 at GameStop and they had a used one for $10.
two-zero said:
I had a similar problem (not the same). After using a 2.5 to 3.5 mm adapter my phone speakers and the mic didn't work anymore. I was about to send the device in, when I read about a solution (I think it was in XDA-Dev somewhere).
You'll have to gently move the headphone jack forward and back, twisting it a litte or even better use some compressed air blowing into the jack. It works best, if you to take out the battery and blow from the back.
My speakers work again, but the same thing happens now and then. It seems there is some switch inside the headphone/mic jack, which doesn't go back. That only happens when I use the adapter.
Click to expand...
Click to collapse
In your case, I would say that sounds like a bad adapter. I routinely use one in mine and don't have that problem. It's one of those nasty stick adapters though, so you have to be careful with them. I've seen some cable type adapters for not too much so you might look into one of those instead.
Found info which might help
HERE IS AN/THE ANSWER.
My WIZA200 and Sony P900 phone the mic headsets are compatable, even the answer button works. If you cant find what your looking for under the flavour WIZa or HTC etc... just look for what you need as a P900 type and you will be sorted.
I just checked the pinouts and this answers the very much asked question... what are the pinouts.... here they are....
http://pinouts.ru/CellularPhones-P-W/sonyericssson_headset_pinout.shtml
FOR WIZA AND SONY P900 >>>> 2.5mm 4 pole jack: PIN1 LEFT+, PIN2 RIGHT+, PIN3 MIC+, SHIELD(PIN4) GROUND. I just checked with multimeter and to get call answer pin3 mic and shield must short to signal the press of the answer button.
---
Just for reference Nokia 2.5mm 4pole jack is very odd... this is how they do it.
http://pinouts.ru/CellularPhones-Nokia/nokia_headset_pinout.shtml
on 4pole 2.5mm: 1=speaker+(positive) ### 2=mic+ ### 3=speaker -(negative) ### pin4 = mic - ###short mic+ and mic - to answer call
on 3pole 2.5mm: 1=speaker+(positive) 2=mic+ 3=shield(ground-negative) ### to answer call short speaker and shield.
See how they change their minds... first on 4 pole jacks answer call was on mic side short, then it goes on 3 pole jacks to short the speaker and ground to answer call... can these guys not make up their minds. Grrrr... totally baffling logic in this design, escept they can keep you buying specialised gear for each phone
Glad to see Sony and HTC used a more logical system and seem to stick to it. I suspect the HTC Touch HD 3.5mm is wired the same as the Wiza 2.5mm system just 3.5mm jack not 2.5mm jack.
Someone should make a 2.5mm 4pole to 3.5mm 4 pole converter to use old cherised headsets on the HTC Touch HD... know of any, anyone?
kull said:
Sigh... still no proper in ear headset (monaural) in sight... :?
Click to expand...
Click to collapse
Another solution.....
I know this might sound odd but a simple solution is get your stereo headset & mic thing and cut the right earpiece lead off...
Now you may have to strip the wire a bit and wrap a piece of insulating tape to stop the wires inside touching, which will cause problems (crackling or loss of audio on remaining speaker most likely). Once the wires are safely insulated away, youll have what you are seeking, a monaural one earpiece mic heaset... saves having to buy one that your finding hard to do.
Seems a shame to sacrifice a stereo headset down to mono, but if thats your poison, go for it.
pinouts.ru is the shiz
Get out the soldering iron and make a frankenstien. I grafted a 3.5 female to my old nokia's pop port so I could hook it to my stereo (before I got a BT adapter) and to my amplified helmet speakers (that were sorced from a computer speaker set.) Before I lost the phone I was planning to add a 2.5 mono female socket for a lil clip-on mic I have. Point being, it's only 3 signals and a ground, should be able to come up with something.
ts worth having a go
Yeah having a go is definately worth it. I just utilised the pinouts.ru stuff and a bit of personal common sense knowledge of the wirings and managed to make myself a 3.5 touch hd 4 pole jack into a 3.5 3 pole jack which works ofr my aircraft. I can now fly and make calls through my pilots headset. It shows it can work. You arent dealing with any dangerous voltages... its all piddly "put it on your tongue and you wont get hurt" voltages... speakers and mics... all easy to work out. Worth having a go.

TyTN x Sony Crossover!. Solution to the lack of audio port!

Just a bit of whining here...
The TyTN seems fine after a month of use but the headset issue is blowing my mind. I want to listen to the music and talk on the phone with some quality headsets.
First the supplied headset is a non standard USB, you cannot use your own headphones or connect to speaker inputs. Bluetooth stereo headsets are available but I believe that they are still too bulky and the technology is not yet fully developed.
You can't charge the phone while using the headset. This is just dumb, Very dumb.
Needless to say the quality of the supplied headset is not good, it is not even recognized by the phone as headset when you connect it. If you connect it to your phone while the phone is non silent, the phone still rings and not just your headset.
I have no idea why HTC is doing this, the TyTN is a relatively large device and it doesnt make sense that there are no spaces for a 2.5mm plug where you can buy all kidns of aftermarket wired headsets for it. Even the high end headset makers SHURE make headsets with the 2.5mm...
Finally I've made a move. TyTN X Sony Crossover Custom Headphones.
I've used a solder to remove the original earbuds wire and soldered a pair of cut SONY MDR-EX71SL headphones on. They sound 100 times better than the stock ones. This will ease my frustrations for now. I was tempted to solder my MDR-EX90LP on but they are $100 a pair. Too much for now
Later on I will try to rework the stock mini USB headphone and make a 2.5mm connector for it so I can use all kinds of headphones(with mic) and connect to a speaker system as I want!
EDIT: It appears that the original mini USB headset has 6 wires, 4 should be for the headphones and the remaining 2 for the mic, I can simply cut up the wire right after the mini USB port and connect the 6 wires to a standard cell phone headset 2.5mm connector then I should be able to connect the TyTN to all kinds of headsets![/img]
Arent you essentially doin this? http://www.4winmobile.com/tutorial-replace-hermes-headset-connector-with-35mm-socket-vt3146.html as seen in another post, seems like the most universal way to solve the problem.
I do like the way you built a set without a plug, cleaner..less cord and weight, but I know myself, I go through a pair of headphones about every 2 months on my mp3 player, Id hate to have to redo the soldering everytime, I expect with the headphones being such an issue for most peple that the market will be flodded in a month or so with headphones for the tytn, or atleast adapters, shoot, the one guy in the above url even offered to do it for free, as long as you bought the plug.
is there still no adaptor available to buy?
i just do this way........
can swap any earpiece....
crash74 said:
i just do this way........
can swap any earpiece....
Click to expand...
Click to collapse
@crash74
Looks very good, even more solid than the other solution, but how do you open the unit to reach the print, is their any trick?!
Can i also use the new connection as a line-out for little active stereo boxes, or is this to tricky for TyTn/boxes?
worked like a dream i have no more crapy hissing inbetween tracks and now i can play my song thu my hi-fi that 1 to the modders and 0 to htc
Adapter usb to 3.5 jack
Go to semsons.com, they have the adapter
qing84, I have the same headphones as u=) firstly I solve this problem like you, but I smash the small "black box"=) with mic and volume control, and i was need connect my mdr-ex71 directly to TyTN without "black box"=(
I was glad that i did it, because sound became much more louder, and more clean...
qing84 said:
Just a bit of whining here...
The TyTN seems fine after a month of use but the headset issue is blowing my mind. I want to listen to the music and talk on the phone with some quality headsets.
First the supplied headset is a non standard USB, you cannot use your own headphones or connect to speaker inputs. Bluetooth stereo headsets are available but I believe that they are still too bulky and the technology is not yet fully developed.
You can't charge the phone while using the headset. This is just dumb, Very dumb.
Needless to say the quality of the supplied headset is not good, it is not even recognized by the phone as headset when you connect it. If you connect it to your phone while the phone is non silent, the phone still rings and not just your headset.
I have no idea why HTC is doing this, the TyTN is a relatively large device and it doesnt make sense that there are no spaces for a 2.5mm plug where you can buy all kidns of aftermarket wired headsets for it. Even the high end headset makers SHURE make headsets with the 2.5mm...
Click to expand...
Click to collapse
umm...you could have just bought this.... http://www.cellphoneshop.net/auadforci85.html
i think its a good idea to replace the head phone leaving the mic in workin condition.as there is no connector is still available at least in my town.i ll try it tomorrow.thanx dude

Headphone adapters

For anyone who wants to order their 3.5mm solution now, take a look at this one from HTC: http://www.expansys-usa.com/p.aspx?i=159613
It’s the page for one listed as being for a Touch Cruise, but there’s a page with one for every HTC phone. I’ve been using it for a few months on my HTC Touch Cruise and it’s great. The plug itself is compact, no different in size than a 3.5mm headphone plug -- and stays put (it isn't shown in the photo). It has 2 parts, the cord with the plug at one end, and a microphone with a 3.5mm jack at the other. The other part is the throwaway earbud headphones that you can toss and use your own. No bulky dongle, and makes any favorite pair of headphones into your microphone/stereo headset. Personally, I forget HTC forgot the 3.5mm jack with this one, as it's just a cable, not an annoying adapter.
The pinout of the mini-usb jack on the G1 is the same as all other HTC phones, so at the very least the microphone and stereo audio will work. Some features of the answer-button that may or may not work on the G1: push once to answer; pushing while on a call places the call on hold; 2 quick presses redials the last number; 1 long press activates voice dial. Most likely, the button will mimick whatever functionality is present with the headset that ships with the device.
It's made by HTC, and is very durable. Beware the adapters from Seidio -- they last a couple weeks and then start to give out, audio stutters, fades in/out -- they're not constructed well and within a month or so the ends start to get loose from the wire; and you can't exactly run to Best Buy for replacements.
The budget-shipping rate from MobilePlanet.com should have them to you well before your G1 arrives
Question. How far will the microphone be from my mouth? How good is the microphone...the problem is my regular headphones are kinda long like the wire is probably a good 20 inches.
So by the time its plugged into the adapter the mic is gonna be 20 inches from my mouth..and I want to be able to pic up without using the phone? will it work?
Probably -- the mic is in the end that your headphones plug into, I don't know how long it is, but I do hold the mic up a bit when I use it as that. Primarily, I like it as it's not a dongle and in use is no different than having a 3.5mm headphone plugged in. The plug itself isn't big, it stays put, and if I need to speak on it I can. The mic quality is OK, though it picks up all background noise, and a slight breeze can sound like a windstorm. Talking on it is just a convenience for me, I really wanted a standard type stereo headphone cable that I could pick up a call on. My devices tend to be music players first, and phones 2nd.
FearlessM said:
Question. How far will the microphone be from my mouth? How good is the microphone...the problem is my regular headphones are kinda long like the wire is probably a good 20 inches.
So by the time its plugged into the adapter the mic is gonna be 20 inches from my mouth..and I want to be able to pic up without using the phone? will it work?
Click to expand...
Click to collapse
Earbuds w/out Mic/Converter?
Hey all,
I've been looking for some earbuds that don't require an adapter and just plug into the G1's current plug, or have an annoying mic; just to listen to music with.
Something that would eliminate the need for this: http://cgi.ebay.com/2-5mm-Headset-H...14&_trkparms=72:1205|66:2|65:12|39:1|240:1318
Does anyone know where I can find some?
Thx
grim1234 said:
Hey all,
I've been looking for some earbuds that don't require an adapter and just plug into the G1's current plug, or have an annoying mic; just to listen to music with.
Something that would eliminate the need for this: http://cgi.ebay.com/2-5mm-Headset-H...14&_trkparms=72:1205|66:2|65:12|39:1|240:1318
Does anyone know where I can find some?
Thx
Click to expand...
Click to collapse
While I don't endorse this company, they seem to have quite a selection. http://onlyandroid.mobihand.com/homeAccessories.asp?hCategory=1022 Personally, I am inclinded to get http://onlyandroid.mobihand.com/productaccessories.asp?id=17085&n=HTC-3-in-1-USB-Adapter so I can charge the phone and use the headset of my choice. (This adapter looks like a beast though...)
G/L,
--M
PS that website has the adapter you are looking at on ebay for less... just fyi.
mini usb to rca adapter
is there a mini usb to rca adapter that can work with the g1?
Well, it's got 2 reviews, and a rating of 1 star on the company's site... There are tons of them on eBay, wonder if those are terrible... I suspect so.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280277868575
I ordered a few of those. I will let you guys know how long it takes to get to the US and how I like the adapter itself. I also need one for the car that lets me charge and then convert to 3.5 to go into my aux input in my car.
haitiankid4lyf said:
is there a mini usb to rca adapter that can work with the g1?
Click to expand...
Click to collapse
Might be easiest to go USB -> 3.5mm -> RCA. Not elegant but parts are available.
--M
yeah i was thinking about that, but two different adapters but i guess thats the only way for now
thanks
http://www.google.com/products?q=mini+usb+to+rca&btnG=Search+Products&hl=en&show=dd
found some but dont know if they will work
Here is a good 3.5 adapter that lets you charge at the same time.
http://www.expansys-usa.com/p.aspx?i=171920
benjimen said:
Probably -- the mic is in the end that your headphones plug into, I don't know how long it is, but I do hold the mic up a bit when I use it as that. Primarily, I like it as it's not a dongle and in use is no different than having a 3.5mm headphone plugged in. The plug itself isn't big, it stays put, and if I need to speak on it I can. The mic quality is OK, though it picks up all background noise, and a slight breeze can sound like a windstorm. Talking on it is just a convenience for me, I really wanted a standard type stereo headphone cable that I could pick up a call on. My devices tend to be music players first, and phones 2nd.
Click to expand...
Click to collapse
how do you find the audio quality through headphones? little worried as i hear through its own speakers it can be a litte on the quiet side :/
bobby digital said:
how do you find the audio quality through headphones? little worried as i hear through its own speakers it can be a litte on the quiet side :/
Click to expand...
Click to collapse
Same volume as the headset that ships with it. Try it and see.
sorry i wasnt clear, i didnt mean does an adaptor effect the sound, purely what is mp3 quality and sound like through headphones generally on g1 (standard headphones or not) compared to say i-phone,nokia,sony erricson etc
Sounds good to me.
i have one of those adapters, i got it for my wing way back, i think they were like 99 cents or something so i bought a bunch, they wear out pretty fast though, there nice to play music from my g1 in my car, i just wish there was a way to keep the microphone on the phone so i could talk on the phone and have the audio come through my cars speakers.
Headphone adapter
The newer G1s are shipping with a really nice official headphone adapter in the box, but I can't find it for sale anywhere. Are early adopters just left out in the cold with no headphone support? HTC has these ExtUSB ports on every one of their phones but they don't seem to sell any official adapters so I'm going to be stuck buying sub-par chinese adapters off of Ebay.
anyone have any pictures of what the headphone adapters look like?
wth, i want one official one! maybe calling t-mobile, they will send us one?
It looks the same as the standard headphones the only difference is that at the head phones them selves aren't attached to the remote (one end of the remote is the usb cable and the other is a 3.5mm port) they are 3.5mm head phones. I called t-mobile about it because my brother got one and they said they new nothing they said it wasn't on the packing list so I called HTC and they said they new nothing and since there was no bulletin they could not send me anything. I went to my local t-mobile store asked them about it and they gave me a new one out of a returned phone. The reason that tmobile says that they are not shipping them with a 3.5mm adapter is because its just a modified head phone and not an adapter and head phones in the box. I would recommend going to your local t-mobile store and asking about it.
Sorry about the picture quality I took them with my super G1 camera.

Car cradle/charger with built in FM transmitter

http://www.shop2us.com/car_mount/d2_fm_kit.jpg
Hi All,
I have just purchased and tested this product. It cost just £22 from Ebay. Quite a bargain really. The build quality is quite poor. However, the D2 does fit quite nicely and you don't need to fiddle with it too much to get the mini USB connected. One strange thing is the side flanges. They do overlap the green and red phone buttons slightly, so you could find yourself accidentally calling someone when inserting the D2 into the cradle.
Once in, it is an excellent product. The sound quality through the car radio is superb. Even driving through London (where the airways are filled with legal and illegal radio stations) there is no interference with this transmitter. I have tried a few of these type of FM transmitters and can happily say this is easily the best so far. The volume on the D2 needs to be turned down to about 13 or 20% on the HTC, otherwise you will get some distortion when playing loud music.
Re-tuning is a breeze with the back-lit LCD screen, if the frequency you have it on has some interference.
One problem is making or receiving a call. When a call comes in, you can hear the ringing through the car speakers. However, this device disables the D2 microphone and does not have one built in itself. The only work around for this is to have a bluetooth headset. Therefore, once a call comes in, the bluetooth headset will then provide the sound and microphone and so you can speak/hear as normal. The car speakers will be disabled once you accept the call through the bluetooth headset. Obviously the headset will need to be connected first. Personally, I use a small programme called bluepower. This turns on bluetooth on my D2 when it is being charged and then turns it off (to save battery) when it is not being charged. Therefore, as soon as I put the D2 into the cradle, it links with my already paired bluetooth headset
So, I can now sit in my car with my D2 charging, playing music through my car radio and make/receive calls using my bluetooth headset without any problems....
All sounds great doesn't it?
However, there is one small problem.
If I choose to listen to a different radio station, I will not be able to hear my D2 ring or hear when an email/text comes in, or to the voice guidance on my iGO8 (not that I use it).... You may consider this a safety feature because you don't want to have this distraction whilst driving do you? Obviously you can still see these events in the usual way, if your screen is turned on. This is not such a huge problem I don't think, but some might.
Perhaps it will be easy to be able to somehow link up a working microphone with this system and have a rather decent hands free system, but I don't know how to. I have seen other threads which have also described this problem with other such systems, but never a solution except the bluetooth headset one. Maybe someone can suggest a registry tweak for this or a Mortscript programme???
Anyway, to conclude, I am very happy with this purchase, especially at the price.
Hope this helps someone
will the Pure fit in a TD2 cradle?
Will the Pure fit in a TD2 cradle? The bottom ends appear to be differently shaped. Is it close enough that the two can be interchanged for a cradle like mitsi posted?
I want a nice cradle with a built in usb plug so I dont have to figit. The proclip one is too darn expensive. Whereas the custom fitted car cradles for the TD2 are plentiful...
Mic For the FM Transmitter ALMOST !!!
Well like you i bought one of these fine products I did come across a couple of issues (and work arounds).
1. At certain output frequency's the GPS did not work ??, noticed that when the power to the FM Tx was removed the GPS signal returned. as I tried different channels the interference varied so worth looking out for.
2. Again at different output channels I would pickup the mobile trying to make a connection to the network (approx every 10min), again changed the channel the effect varied from bad to zero.
Microphone, I took my unit apart and the pcb has the position for a MIC marked on the pcb but no mic fitted. I took out a mic from the supplied handsfree kit supplied with the phone this fitted and off I went to try but no luck.
On further investigation the mic needed to be wired pack to the usb plug BUT the pins for the plug are enclosed in the glue used to hold the plug in position and there were no leads off the plug to wire too !!!!!!!!!!!!
But like u the unit is still worth the cash

Question about talking with headphones in.

Alright, my friend has a blackberry and when he's listening to music and his phone rings he can hear it ringing through the headphones. Not only that, he can answer the phone and hear the person in the headphones while talking to him. He basically holds the phone in front of his mouth and talks with his headphones in. Also he doesn't have a mic on his headphones.
I've always wondered if this was possible with the x10. When my phone rings and im listening to music my music stops but the phone rings out loud and not through the headphones. I tried to answer it and see if I could hear them through the headphones but I can't and the person who called can't hear me either unless I unplug them.
Is there any way to fix this so I can hear the person through the headphones and talk to them by talking into the phone?
Sorry if the post doesn't make any sense, I'm tired as hell, just got back from work.
Your head phones come with a mic, imo I think that's better than holding the phone to your mouth.
Sent from my X10a using XDA App
I understand that the default headphones come with a mic, but they never stayed in my ears, which is why I use my own in-ear headphones. I want to be able to use them to listen to the call tho.
But the default headphone cable that comes with the phone has a headphone jack to plug in any headset you want to it, and still have a mic?
I've fixed all my headset issues by buying a £10(roughly) wireless headset adapter off eBay. roughly 12-14 hrs battery life out it (so lasts about a week with moderate usage as I mostly use it in the car on 1-2 hr journeys and do them once or twice a week). Good buy!
Hi Hypercore,
We seem to have gotten our phones from the same place. The default headphones came with a removable mic. When I got mine, I had headphones (with a 2 contact TRS 3.5mm connector + a shorter wire with a microphone that sports a 3 contact TRRS connector).
Heres's the way the tips rings and sleeves work (I think... correct me if I'm wrong)
The headphones TRS
Tip: Left
Ring: Right
Sleeve: Ground
The "Mic TRRS jack"
Tip: Left
Ring1: Right
Ring2: Mic
Sleeve: Ground
So you need a TRRS connector that includes a mic + TRS Headphones or a set of TRRS headphones that include a mic built-in.
There are some pics on wikipedia, just search for TRS connector.
Hope this helps.
I know what you mean, the mic comes with the phone but when I hook my headphones up to it the wire is WAY too long.
Boohoo, just bundle it up a few times and put a rubber band around it keep that end in your pocket.
I just snipped the headphone's wires, slipped some shrink tubing, heat wires up with a lighter (to remove the "varnish/wax/stuff" they put on the copper wires these days), solder, slip the shrink on top, heat up one last time and voilà! Headphones with a short wire.
Hurray!
I have to admit that the mic wire + normal headphones make for a really long wire.

Categories

Resources