Finally got a whole afternoon free so i decided to get my touch dual(Orange UK version) sorted. Did the HardSPL thing and security unlocking following the instruction and it all went fine. Then I flashed the radio back to my original version (1.58.16.27) and installed Tom's Niki project rom V2.13. Just before I was about to install the applications, I noticed the reception level was very poor.
When in the house, half the time there is no service at all and when it finally picks up the signal, it's only 1 or 2 bars. And it's kind of come and go all the time. But the signal goes to FULL as soon as I take the phone outdoors, even when I'm holding it in my hand and reach it out of the window (worrying I may drop it from the 3rd floor lol). That's a significant drop considering it was at least 3 bars indoor before this afternoon. I then put the original Orange rom back in and it didn't get any better. Then I tried all the radios in this thread and none of them works.
The thing is, I only found out about the poor signal after installing the new rom so I have no clue where it went wrong. It could be any of the 3: HardSPL, Security Unlocking & the new rom. I'm not quite good at this so just wondering if anybody can tell which of the above mentioned 3 steps coursed the problem, and if there is any solutions? It's really frustrating when sitting at home waiting for a call & knowing your phone might not work
Many thanks in advance~
Same problem here. I did the same thing you did. I had just unlocked my device and installed the same radio I had before and my reception on the t-mobile rom was 3-4 bars. After installing Tom's rom it seemed to have dropped significantly to 1 bar or, most of the time, no reception at all. I'm gonna try flashing back to the stock rom in the weekend to see if that helps.
use sedna radio!
try to use gsm or edge only!
NetrunnerAT said:
use sedna radio!
try to use gsm or edge only!
Click to expand...
Click to collapse
Thanks for the reply.
I've tried all the radios, including RUU Nike Radio 1.58.21.23S Modded , and tried to use GSM only as well, and neither of them helps
And can anyone tell me where the GSM antenna is in the picture? And what is that black round thing in between the green circle and red circle if it's not the GSM antenna?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
...
yellow = bluetooth and wifi antenna
red = the external antenna onnector
green = a metal blade thats hide the MSM7200 chip and some other ICs
blue = GSM-Antenna
Valvarin said:
yellow = bluetooth and wifi antenna
red = the external antenna onnector
green = a metal blade thats hide the MSM7200 chip and some other ICs
blue = GSM-Antenna
Click to expand...
Click to collapse
Cheers mate
That explains why it drops to no service when I'm holding the bottom part of the phone in hand.
Now, any ideas how to fix it?
I tried to flash back to original Orange rom with original radio and it's not getting any better. Also tried to re-lock the phone and it doesn't help either.
Send it to service! You have a bad connection to the gsm antenna! possible your phone have hit the ground to much ^_^ possible a damage soldering point.
NetrunnerAT said:
Send it to service! You have a bad connection to the gsm antenna! possible your phone have hit the ground to much ^_^ possible a damage soldering point.
Click to expand...
Click to collapse
I am sure that I have never dropped my phone. But I am afraid that I will have to send it back if what HutcheonS tells is right that swapping back to the previous rom and radio won't work.
I'm quite sure I've never dropped the phone too. And it doesn't look like a hardware issue since it just happened after the unlocking & flashing. Anyway I will take it to orange and see what they can do.
refelian, please do try to flash yours back to the original rom & radio and see how it turns out. It could all just be that I didn't get it right.
OK ... 2 ppls have the same problem!
Please Flash this Full Rom for Tests!
http://www.4shared.com/file/3772443..._13171012_Radio_Nike_1582123_signed_Ship.html
It resets OS and Radio to Factory. If it Works, Flash the Sedna Radio and check Signal Problem again ... then Flash you Favorit OS!
If the Signal is low after the Original Firmware, we must check some Value inside the NVRAM, but i am not sure that we able to fix it!
The GSM antenna is held in place (and electrical contact) but the bottom right hand torx screw (star shaped screw driver needed), as you look at the phone with the back off.
Check that this screw is tight...
I just tried switching back to an older rom and radio. I used the same radio I had before (1.58.16.27) which I got from the radio thread on this forum and a rom build I found in another post.
http://forum.xda-developers.com/showthread.php?t=384963
The rom version is 1.31.404.09and regretfully it didn't work. Still no reception here. Still there were some differences with before when my reception was good. Previously I had a slightly different rom, namely one from t-mobile.
rom version: 1.35.114.07
rom date: 12/03/07
radioversion: 1.58.16.27
protocolversion: 25.61.30.03h
niki200
wm6
ce 5.2.1622 (build 18128.0.4.4)
On both niki project and the original rom I have now installed it says niki100 rather than 200 which it was originally. I don't know if this has any impact but there has to be something which caused the sudden drop in reception.
I don't have a torx screw driver GlenH but the screw you are describing doesn't seem to be loose (although without a fitting screw diver I can't be sure).
Please try a not dumped full niki rom!
NetrunnerAT said:
OK ... 2 ppls have the same problem!
Please Flash this Full Rom for Tests!
http://www.4shared.com/file/3772443..._13171012_Radio_Nike_1582123_signed_Ship.html
It resets OS and Radio to Factory. If it Works, Flash the Sedna Radio and check Signal Problem again ... then Flash you Favorit OS!
If the Signal is low after the Original Firmware, we must check some Value inside the NVRAM, but i am not sure that we able to fix it!
Click to expand...
Click to collapse
Just tried that and it doesn't work
Tried to tighten the screw and the is no difference either
The only thing I haven't reverted back is the HardSPL now. Can anyone tell me how to undo it? May as well give it a shot~
this error have nothing todo with hardspl! its a radio problem!
i write you a little manuel ... i need from you a nv-item dump, then i can compare it. morning i give you a step by step guide!
On a side note, if I want my t-mobile branded touch dual back the way it was (original rom) what's the best way to do it? (didn't make a rom dump of the original btw)
I suppose sending it back to t-mobile would be best, but does anybody have any idea how they generally react to unlocked/flashed devices?
Yeah I think I'm gonna send it back to Orange too. And you need to have it re-locked and flashed back to original rom otherwise the warranty is void.
HutcheonS in case you have not returned your device yet (I didn't), I just installed Tom's new radio found here (the latest one)
http://forum.xda-developers.com/showthread.php?t=369502
And it seems to drastically improve my connection. I used to get no service from behind my pc and now I have 2/3 bars. Which is closer to my old situation. I'm gonna walk around a bit and see how it holds out.
Props to Tom for getting this awesome radio.
Can you make a NV-Item Dump? Possible we see some strange Value!
NetrunnerAT said:
Can you make a NV-Item Dump? Possible we see some strange Value!
Click to expand...
Click to collapse
Sure if you could tell me what it exactly is.
On a side note, I have yet to make a successful call on this radio
Every time I try to make a call, it says after some time that I am connected, yet I can't hear a thing. Internet does work though.
I am using a dutch stock rom btw.
Related
hi all, just asking for a problem now...
My camera stopped working, i can view only black, black and black
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
However, when i open htc camera my device slows up a lot, then if i close htc camera all become normal.
So i don't know how to solve this, i hope only that isn't an hardware fault as cmonex said and hope anyone can help me and my athena's camera to live again.
Thanks for reading,
Michele.
Have you tried a hard reset?
For what is worth, my camera also doesn't work - it looks just like yours - black.
I have your ROM installed and I always assumed that is somehow ROM related, but I haven't really tried the camera when I got my Athena (it's not really important for me...) first time I have tried to use it was when I already flashed 1.88 ROM and now with 2.04 ROM.
My camera stopped and i saw just a green screen when i do a soft reset it is start again , i use the micky lastest rom , And in this day I see some buges on camera
it doesn't depend upon my rom, tried to change some roms (original too) but nothing, it remain black
I have been using MiChY's ROM 2.04 MiChY Diamond Edition (5.2.20273, build 20273.1.3.3), camera works normally.
have you tried another camera software like CoolCamera
Time to visit the service centre.
i can't even get my camera to initialise!!!
It was fine until I upgraded the spl in order to play with the new roms. Surely the balance of probabilty would suggest that a hardware failure is less likely than a problem with spl or the rom?
Even downgrading the spl and using michy's rom has not helped
Is it posible to manually install the camera?
i never changed spl. Only installed 1.2 olipro, from there no other change to spl.
I do not remember if my athena has fallen down but i think not.
So this is an internal problem. Now i can view, not only i have this problem too...hope to find a solution
michyprima said:
i never changed spl. Only installed 1.2 olipro, from there no other change to spl.
I do not remember if my athena has fallen down but i think not.
So this is an internal problem. Now i can view, not only i have this problem too...hope to find a solution
Click to expand...
Click to collapse
I would suggest you and the likes try flash back the factory ROM on the device and see if that helps any. If it does from there, you can start fine tuning to see excatly what's going on. Just my 2 cents, and today I noticed some green lines but that might have been due to me focusing on my monitor at work to snap a shot of the webpage I was on. I'm using AP 4.0 with 3.5SPL if anyone's curious. Again just my 2 cents but you guys should give it a shot, just to see if that kicks it back in.
flashed a lot of roms, wm6 original too. nothing, forever the same...
dry joints?
Hi Michy,
Sorry to hear about your problem, I'm not sure that your camera problems are from rom faults as my camera is fine on 2.04. the camera on our units only connect to the mother board via a pressed together joints. This could be what is wrong. Are you brave enough to take your unit to bits? its actualy quite easy if you follow the service manual and have the correct tools, then just whipe the contacts to the camera and board clean with a cotton bud. I had the same fault on another HTC unit and this worked. however it may not though!
Regards
Jay
strange...
when I have the time i'll open it...
but...I noticed that the camera flash works, I think if is this camera's flash do not works...
mah!
WM 6.1 has a policy setting you can use to disable camera among others. You are sure you haven't set this "deny camera" policy?
Probably not as this would be reset when you install a new rom.....
hehe, if my rom have camera disabled, other users could have my problem too
Mine also have this problem....
Anyone can solve this problem??????
responderman said:
Hi Michy,
Sorry to hear about your problem, I'm not sure that your camera problems are from rom faults as my camera is fine on 2.04. the camera on our units only connect to the mother board via a pressed together joints. This could be what is wrong. Are you brave enough to take your unit to bits? its actualy quite easy if you follow the service manual and have the correct tools, then just whipe the contacts to the camera and board clean with a cotton bud. I had the same fault on another HTC unit and this worked. however it may not though!
Regards
Jay
Click to expand...
Click to collapse
Hi responderman,
I have dismantled my Dopod u1000 (athena x7500) to bits a few times. I am having camera problems. But i noticed that the camera is connected to the flash and appears to be soldered onto the main board. I tried wiping the back portion of the camera believing it to be where the cmos sensor is located but did not notice any feedbacks on my lcd screen showing that my wiping action is affecting the camera in anyway. As for removing the camera and cleaning the connections i haven't tried that because as i said, it appears to be connected to the flash and the flash appears to be soldered onto the main board.
Any ideas or info? Thanks!
I also have my camera broken, only after a month I bought it, it started showing some green effect though it barely showed the image, even after hard reset, ROM change there was no change, recently my device fell from a table, and since that I have the same screen as Michy's, most of the time Camera doesn't initialize.
I believe it is camera hardware that is broken.
well i think that too. for that i'm not trying to restore it anymore. if anyone got it to work, plz share
I've had my Titan for maybe 3-4 months and I am SO sick of my WiFi getting disconnected constantly. Will sell it and get a Galaxy Note instead. Any of you with the same issue?
nope...my titan works great...wifi works without disconnections...at home at work and at all other places im logging in....but i hear that many people have this issue....dont know but maybe a hardware revisions issue...dont hope so...i like the titan....a great phone from htc...and i like wp.....dont want change with anything
Sent from my TITAN X310e using Board Express
Try settings your router to 150 802.11n, instead of 300, the phone specs says 802.11b/g/n(150).
Maybe having the router on 300 the device cant detect it reliably..
Wombat said:
Try settings your router to 150 802.11n, instead of 300, the phone specs says 802.11b/g/n(150).
Maybe having the router on 300 the device cant detect it reliably..
Click to expand...
Click to collapse
What is the 300? I can't seem to find anything like it.
Nope. Mine works fine. Couldn't be happier. If it's only with one particular wi-fi connection, I'd check what channel the router is using. I've had problems before due to my neighbour using the same channel as me.
prgwhiting said:
Nope. Mine works fine. Couldn't be happier. If it's only with one particular wi-fi connection, I'd check what channel the router is using. I've had problems before due to my neighbour using the same channel as me.
Click to expand...
Click to collapse
It's using "auto".
tooly26 said:
nope...my titan works great...wifi works without disconnections...at home at work and at all other places im logging in....but i hear that many people have this issue....dont know but maybe a hardware revisions issue...dont hope so...i like the titan....a great phone from htc...and i like wp.....dont want change with anything
Sent from my TITAN X310e using Board Express
Click to expand...
Click to collapse
This is my experience exactly - totally happy with my awesome phone with one exception: outgoing voice quality. It's horrid. I made the mistake of recommending the Titan to my Dad, and now I can hear how bad I've been sounding to others. When I call him, it's just "What?" "What?" "What?" "What?"
I have had the exact same problems with my Titan, finally had enough when Phone signal started playing up as well. Sent it back to HTC, on the first return they replaced the motherboard and a sensor but when I got it back the problems were worse and I couldn't actually connect to the mobile network. So sent it back, according to them they have replaced additional PCBs and some other sensors. Since getting it back this time it works perfectly, no problems switching automatically between mobile network and wifi for data, voice quality is 100x better and the phone is a joy to use.
TheDisneyMagic said:
I have had the exact same problems with my Titan, finally had enough when Phone signal started playing up as well. Sent it back to HTC, on the first return they replaced the motherboard and a sensor but when I got it back the problems were worse and I couldn't actually connect to the mobile network. So sent it back, according to them they have replaced additional PCBs and some other sensors. Since getting it back this time it works perfectly, no problems switching automatically between mobile network and wifi for data, voice quality is 100x better and the phone is a joy to use.
Click to expand...
Click to collapse
Thanks for the reply. I'm not sure my phone signal have started being crazy but I've noticed that sometimes it's down to zero bars (with the icon over so no calls can come in/out). Maybe it's because of a death-grip of some sort.
Mine worked perfectly during the first 4 months. Then suddenly it wouldn't anymore connect to wifi routers. That is, low signal, does not reconnect, no signal at more than a few meters away from router, etc.
I eventually sent it for repair with clear explanations, but all these ah did was to re-install the software... I got desperate until a few minutes ago when I tried to open and clean the contacts of the back cover. It didn't help, but I tried instinctly to test the wifi signal after applying pressure with my thumbs against the phone's screen, so as to improve the contact with the back cover. Result = instant improvement from 2 bars (2 meters away from router) to 5 bars!
Next step, I opened the back, and with the help of a knife, I bent slightly the metal parts that are used for antenna contacts with the phone. I put the back over and miracle, the signal is now perfect with 5 bars, and without having to press the phone!
Well, I don't know until when the trick will work, and if you attempt to do it, be very careful not to spoil these metal parts. I'm happy for the time being
Prerna said:
Mine worked perfectly during the first 4 months. Then suddenly it wouldn't anymore connect to wifi routers. That is, low signal, does not reconnect, no signal at more than a few meters away from router, etc.
I eventually sent it for repair with clear explanations, but all these ah did was to re-install the software... I got desperate until a few minutes ago when I tried to open and clean the contacts of the back cover. It didn't help, but I tried instinctly to test the wifi signal after applying pressure with my thumbs against the phone's screen, so as to improve the contact with the back cover. Result = instant improvement from 2 bars (2 meters away from router) to 5 bars!
Next step, I opened the back, and with the help of a knife, I bent slightly the metal parts that are used for antenna contacts with the phone. I put the back over and miracle, the signal is now perfect with 5 bars, and without having to press the phone!
Well, I don't know until when the trick will work, and if you attempt to do it, be very careful not to spoil these metal parts. I'm happy for the time being
Click to expand...
Click to collapse
Could u show me some pictures, please?
The way u did to your contacts?
GinCifer said:
Could u show me some pictures, please?
The way u did to your contacts?
Click to expand...
Click to collapse
Mostly likely "Prerna" lifted the contacts upward so as to make contact with the back cover, but since their small/thin they can easily be broken = useless or eventually become loose.
http://wmpoweruser.com/htc-titan-having-antenna-issues/
Celluar Antenna .. Wifi Should be the pins on top
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Example: I had an iPhone that the home button had to be pushed down very hard to register so i took it apart and noticed that right below the button were two pins .. I slightly lifted them up just a bit and now the button was working without lag... but some time afterwards it started happening again and i tried lifting the pins but they broke and i had to get it replaced.
Voice Quality Issue
drokkon said:
This is my experience exactly - totally happy with my awesome phone with one exception: outgoing voice quality. It's horrid. I made the mistake of recommending the Titan to my Dad, and now I can hear how bad I've been sounding to others. When I call him, it's just "What?" "What?" "What?" "What?"
Click to expand...
Click to collapse
Have you and your Dad gotten any help on the voice quality issue? Have you told AT&T about it?
I'm on my 3rd Titan from AT&T all having the same voice quality problem. I just received my 4th one in the mail today and I'm sure it'll have the same issue!
Personally, I'm getting a little tired of re-installing all the apps and begging Microsoft to delete the old titan from list of 3 devices allowed to play zune content!
i have testet yesterday the voice and music sound quality....i can hear everthing...and the person on the other line can hear me clear too...no muffled sounds.....i have a debranded titan with latest updates...
Sent from my TITAN X310e using Board Express
i had to return my titan because the muffled sound problem was unbearable. Leave yourself a voicemail to test it. I think it may be an app that causes the problem. Test after a hard reset again.
tboy2000 said:
i had to return my titan because the muffled sound problem was unbearable. Leave yourself a voicemail to test it. I think it may be an app that causes the problem. Test after a hard reset again.
Click to expand...
Click to collapse
Not sure that it is an app causing the problem because like I said yesterday, my latest replacement device showed up yesterday (my 3rd) and right out of the box, I called AT&T and they could not hear me. I was practically screaming and all three phone calls, no one could hear me.
Then taking my sim card out and putting it back in an unlocked HTC HD2 to continue working for the day, I later called AT&T back for yet another replacement and they said that they must do diagnostic on it with my sim card in it. So I did that and used my wife's phone to speak to AT&T and they proceeded to call me on my Titan and I answered and they could hear me fine. They asked me to call someone from my contacts list and I did and they too could hear me fine. So either I'm an idiot or everyone that I talk to are liars (including my wife that says she can't hear me).
The phone isn't consistent with the problem. It's like an interference of some sort. I've used it today without problems! Not sure what it is, but I know once I re-install my 200+ apps, call MS and beg for it to be one of my allowed 3 devices and set it all back up, then it'll start acting up again only to start the whole damn cycle over again!
Tooly26, how did you "unbrand" your phone? Is this procedure for Eur phones or US AT&T as well?
Any help is appreciated because I'm really regretting buying this phone.
i think my method works for every provider...but a dont have seen a htc stock rom for us....when u can find a htc stock rom for us i can make step by step instruction...
Sent from my TITAN X310e using Board Express
[email protected] said:
Not sure that it is an app causing the problem because like I said yesterday, my latest replacement device showed up yesterday (my 3rd) and right out of the box, I called AT&T and they could not hear me. I was practically screaming and all three phone calls, no one could hear me.
Then taking my sim card out and putting it back in an unlocked HTC HD2 to continue working for the day, I later called AT&T back for yet another replacement and they said that they must do diagnostic on it with my sim card in it. So I did that and used my wife's phone to speak to AT&T and they proceeded to call me on my Titan and I answered and they could hear me fine. They asked me to call someone from my contacts list and I did and they too could hear me fine. So either I'm an idiot or everyone that I talk to are liars (including my wife that says she can't hear me).
The phone isn't consistent with the problem. It's like an interference of some sort. I've used it today without problems! Not sure what it is, but I know once I re-install my 200+ apps, call MS and beg for it to be one of my allowed 3 devices and set it all back up, then it'll start acting up again only to start the whole damn cycle over again!
Tooly26, how did you "unbrand" your phone? Is this procedure for Eur phones or US AT&T as well?
Any help is appreciated because I'm really regretting buying this phone.
Click to expand...
Click to collapse
Hi, same experience here. I have this problem since I got it out of the box without loading any app into it. I am also using a Titan from ATT. Have you tried to put a tape on the top mic? It helps and improves voice quality. But I have to say even with this fix, the voice quality is still not as good as my old iphone 3gs.
Seems like there's alot of issues with the Titan, not just the WiFi. I'm still leaning towards the Note tho, I do love WP7 but I also have to say I'm a bit tired of the low resolution, it kinda sets me off. Need something fresh really =)
Yes, I am in the same situation too. I am going to give up the HTC Titan and go back to a Android device.
They have repaired my HTC Titan two times, with new mainboard and back cover, but still the outgoing sound quality is so bad in some calls and the WiFi is buggy.
I think the WiFi issue must be some kind of software bug.
And I hate the fact that even 1/30 on the volume is so loud when playing games or watching movies.
And the low res and low dpi screen is more annoying then I thought it would be.
WP7.5 wasnt really what I expected and the HTC Titan was really not the flag ship phone to make it justice.
Hi guys,
I'm having serious trouble with my Droid RAZR lately (started like 2 weeks ago).
People have a hard time hearing my while in a phone call, I basically got to yell in the phone for them to hear me
Interesting piece of trivia, as I'm doing some test atm : When I call someone I can hear myself very clearly in my own speaker while it's very very low on the other phone.
So i guess the microphone is working properly from a "mechanical" point of view. I've tried a Skype call, seems ok to me so I guess it's a "software" problem
Does anyone ever encounter this problem ?
Few more technical info, phone is ROOTED Droid RAZR XT910 (GSM, bought in France):
Android 2.3.6
System version : 651.167.22XT910.retail.en.FR (Stock ROM)
Kernel : 2.6.35.7-g24431a2
Build : 6.5.1-167_SPU-15-M2-1-FR
Thank you for your time and help guys.
Cheers,
Boris.
Dian Z said:
Hi guys,
I'm having serious trouble with my Droid RAZR lately (started like 2 weeks ago).
People have a hard time hearing my while in a phone call, I basicaly got to yell in the phone for them to hear me
Interresting piece of trivia, as I'm doing some test atm : When I call someone I can hear myself very clearly in my own speaker while it's very very low on the other phone.
So i guess the microphone is working properly from a "mechanical" point of view. I've tried a Skype call, seems ok to me so I guess it's a "software" problem
Does anyone ever incounter this problem ?
Few more technical info, phone is ROOTED Droid RAZR XT910 (GSM, bought in France):
Andorid 2.3.6
System version : 651.167.22XT910.retail.en.FR (Stock ROM)
Kernel : 2.6.35.7-g24431a2
Build : 6.5.1-167_SPU-15-M2-1-FR
Thank you for your time and help guys.
Cheers,
Boris.
Click to expand...
Click to collapse
Hi, have you ever tried a new Rom? What you did so far to fix this issue? Did you a factory reset? Let me know. Since its working fine on skype this really seems to be a software related issue.
Cheers
Enviado de meu XT910 usando o Tapatalk 2
I haven't done anything yet other that looking for a solution on the Internet and trying to find out if it's a mechanical or software problem.
The microphone holes are in front and back on the RAZR, so I try removing my protective case (which blocks the hole on the back of the phone) but it's the same. The holes are clean btw, no dust or anything inside from what I can tell.
I'll probably back everything up and try a factory reset if no one has encounter this problem before (I thought I would wait for XDA guy's opinion first).
I had the same issue on mine. Just flash the correct Baseband or Firmware for your Region and you'll be fine.
Gesendet von meinem XT910 mit Tapatalk 2
So factory reset right ?
Sent from my Transformer TF101 using XDA
Factory Reset won't change your Baseband. You can try to reset, but the problem would still be the same.
I've flashed another Rom to solve that. To be sure your mic is definitely not defect, try an voice recorder an listen your record
https://play.google.com/store/apps/details?id=de.fun2code.android.voicerecord
In this Thread, you find 2 Fastboot Files. First I've posted got Baseband 93, the second 91.
http://forum.xda-developers.com/showthread.php?p=26893183
Flash that Fastboot, that has NOT your actual Baseband with RSD.
You also can try to flash only the Radio.img over Fastboot. There's an nice Thread in Dev section about this.
http://forum.xda-developers.com/showthread.php?p=20652740
Gesendet von meinem XT910 mit Tapatalk 2
Thx you guys for your replies.
I have some searching/learning to do on how to flash and do all this... or I'll probably end up bricking the thing ^^. Plus I've read somewhere that SafeStrap is only for CDMA version and I got it installed with the rooting process so it's kind of a mess right now.
So I'll set everything straight, get all software needed (RSD etc..) and try to flash a fastboot. I got Baseband version 93P so I'll probably try the one you provided on the thread you linked HSD-Pilot, thx man.
I'll let you know what happens .
Oh and I've tried the voice recorder and it kinda works, only I got to yell in the damn phone for the VU-Meter to move. So it's just like while calling someone.
OK so I just tried flashing a fastboot file, this one:
Code:
SPDREM_U_01.6.5.1-167_SPU-15-M2-3_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml.zip
I know it's the same baseband (93P) but I wanted to try with the latest version I could find.
No surprise, it didn't change anything.
I'm downloading the fastboot with baseband version 91P (the one provided by HSD Pilot), I'll try flashing this tonight see want it does.
Related question : Is this normal that the fastboot flash didn't remove all my application and all my stuff ? I thought it was a way to get the phone back what it was out of the shop ?
It's no Full Flash Rom, so it won't touch your internal SD.
Gesendet von meinem XT910 mit Tapatalk 2
I just did a flash with the file you provide HSD-Pilot (91P Baseband) and it's the same.
I hear myself in my own phone (very clearly, again... so the internal mic is working pretty well) but the guy on the other side won't hear me if I don't yell in the phone...
I think I'll put in back full stock and return it to the store... don't know what else to do.
Here is some kind pf proof that the microphone works :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It's a screenshot from an app that is suppose to find out own much noise the mic is picking up, you can see the min (36 dB) and max value (101 dB) is when I blow air with my mouth where the mic hole is located on the phone.
Im experience similar problem. When I answer with my left ear pepole having hard time hearing me, then I just change ear and they can hear me perfect. Even if I change back to my left ear.
Very annoying!
Anyone else having this problem?
Soulwar said:
Im experience similar problem. When I answer with my left ear pepole having hard time hearing me, then I just change ear and they can hear me perfect. Even if I change back to my left ear.
Very annoying!
Anyone else having this problem?
Click to expand...
Click to collapse
One possibility:
Finally decided to take it back to the shop.
SO I'm getting it back to stock and just "bricked it". I'm having a cdt.bin_signed" -> Phone return FAIL in RSD Lite.
Soulwar said:
Im experience similar problem. When I answer with my left ear pepole having hard time hearing me, then I just change ear and they can hear me perfect. Even if I change back to my left ear.
Very annoying!
Anyone else having this problem?
Click to expand...
Click to collapse
Makes me think, it might have to do with the proximity sensor that cuts off the screen when you cover it. Switching from left to right ears "uncovers" it, the screen turn back on, something to do with the microphone might get altered at the same time and BAM it works fine with your right ear...
Yeah no I'm crazy...
Got out of trouble thanks to this http://sbf.droid-developers.org/
So big thanks to Skrilax_CZ for all those fastboot file !
Hey ppl,
Bought this phone quite recently and to my surprise it has sensors that don't work at all.Now after doing some research I've found out that it could be various problems, but I decided to buy a COMPLETLY NEW PROXIMITY SENSOR off internet.So after I replacing it I haven't achieved anything.This is the picture that I get when i enter *#0*# code and go into sensors.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Please note that these same values (alltitude stuck at 44000m and etc) were present before and after replacing sensor with new one.Also these values are not moving at all like they should.
So my question is what the hell could this be because I've done some googling and noone really had this kind of problem.What could it be?Something to do with motherboard, software problem or something else.
My earpiece speaker is working, and it is all connecte together (sensor,earpiece its all one part , below is picture of it).If it was indeeed non-working part then probably earpiece speaker wouldn't work either.
Please help if you have any info on this matter
Thanks
malique93 said:
Hey ppl,
Bought this phone quite recently and to my surprise it has sensors that don't work at all.Now after doing some research I've found out that it could be various problems, but I decided to buy a COMPLETLY NEW PROXIMITY SENSOR off internet.So after I replacing it I haven't achieved anything.This is the picture that I get when i enter *#0*# code and go into sensors.
Please note that these same values (alltitude stuck at 44000m and etc) were present before and after replacing sensor with new one.Also these values are not moving at all like they should.
So my question is what the hell could this be because I've done some googling and noone really had this kind of problem.What could it be?Something to do with motherboard, software problem or something else.
My earpiece speaker is working, and it is all connecte together (sensor,earpiece its all one part , below is picture of it).If it was indeeed non-working part then probably earpiece speaker wouldn't work either.
Please help if you have any info on this matter
Thanks
Click to expand...
Click to collapse
My advice is if you replaced it with a brand new one and its still not working it is a software issue. Try and flash stock firmware see if that fixes it.
Funny thing is that today I did that.Went to sammobile website, found stock firmware for my country and flashed it on phone.Everything went okay and process was successful.However readings of those sensor values are still stuck and not moving.
I don't know what else to say.I mean come on, how could this be and how in the world was someone able to screw this much that changing with brand new sensor doesn't help.
Some of ideas that I have that could potentially explain why it is not working are: maybe flex cable is not completely operating that is somehow does not clip all the way and thus not enabling it to work properly.However, it is probably highly unlikely since earpiece speaker is working.
Maybe two holes for sensors are blocking sensors but then again I checked them while I was disassembling phone.
I was seeing people fixing sensor problems with fiddling with some sensor files in system directory, and by adding or modifying certain files in there it resolved their issues.
There must be some solution.Only if I knew how it got malfunctioning in the first place I would knew where to look.
Any suggestiong are very welcomed...
Okay so today I flashed XtreStoLite ROM on my phone hoping that maybe I will fix this problem.However, it hasn't improved it.My last option will be to flash different kernel on my phone.And that will be pretty much it cause I dont know what else to do since you know I mean what else is there really to be done anymore.But I'm really curious who managed to f*ck sensor this much that, how in the world are ppl capable of that.
Anyway, will keep this updating with new news just in case anyone manages to get same problem or something similar so if I somehow am able to get it working again , I'm gonna say what it is.
Cheers
malique93 said:
Okay so today I flashed XtreStoLite ROM on my phone hoping that maybe I will fix this problem.However, it hasn't improved it.My last option will be to flash different kernel on my phone.And that will be pretty much it cause I dont know what else to do since you know I mean what else is there really to be done anymore.But I'm really curious who managed to f*ck sensor this much that, how in the world are ppl capable of that.
Anyway, will keep this updating with new news just in case anyone manages to get same problem or something similar so if I somehow am able to get it working again , I'm gonna say what it is.
Cheers
Click to expand...
Click to collapse
I would reccomend trying arter97 kernel. Its a very good stable kernel.
Hi, I begin to have this exact problem a couple of days ago. Have you solved it?. I've tried everyting related to software and ROM's (not custom ones, and everything without being root) but nothing changes. I would appreciate any help. Thanks.
Hi,
I recently bought a Motorola Moto 360 (2nd Gen) from ebay. It was hard to find, I live in Germany and I couldnt find new watches under 400€. So I bought a watch from ebay which was manufacturer refurbished.
Yesterday it arrived and I really do have some questions and I dont understand some stuff:
1. The seller said it was manufacturer refurbished. But it doesnt look like it was. From ebay's description it should be cleaned, and it didnt look cleaned when it arrived. Besides the glass there is coming out glue which is really hard to remove for me now.
2. A friend also has the watch but did buy it original. My watch has 4 "stamps" on its back (look image). My friend doesnt have those. Also the metal latch to change the band does not exist. How can I change my band now? The software on it says, its model is "smelt". My friends watch just says Moto 360 model.
What the **** is my watch? There is almost nothing of information about that codename smelt.
And also on its front side the bottom part which is not part of display is black of my friends watch, mine has motorola logo which seems to be a small sticker that was glued too much above the display... (image 2).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you need more information, let me know. But please tell me if this watch is some kind of fake moto 360 2nd gen... I am really curious about that.
Seems you have some development version of the moto 360. Check this:
http://www.ibtimes.co.uk/moto-360-android-wear-smartwatch-sequel-codenamed-smelt-likely-pack-high-resolution-screen-1494946
Well that's also not much information, were I tricked?
Am I able to change the bands with that watch?
I found out more stuff now: On this watch is a userdebug build installed of a totally outdated Android Wear Firmware. Is there any way to update it manually to the latest? Because the OTA just says its up 2 date but it isnt.
Changing bands is no problem as all band were like that before the quick release bands became available less than two years ago. This video may br helpful: https://youtu.be/TtPde-M5Xz0
By the way, this is the type of band I use.
I'm not sure a pre-release version of the watch is updatable, but check to see that the version of Android Wear is up to date on your phone.
stevemw said:
Changing bands is no problem as all band were like that before the quick release bands became available less than two years ago. This video may br helpful: https://youtu.be/TtPde-M5Xz0
By the way, this is the type of band I use.
I'm not sure a pre-release version of the watch is updatable, but check to see that the version of Android Wear is up to date on your phone.
Click to expand...
Click to collapse
Updatable via OTA probably not, but is it possible by flashing it? I mean there is no physical input/output on the watch. But is there any possibility when I open the back of the watch and creating an USB cable ?
Is there official up 2 date ROMs on the internet which I can simply flash over the current one?
Edit: I just noticed that my watch is rooted. I wanted to debug the watch via bluetooth and tried to ls /system directory which first failed because of permission. Then I entered su and tried the command again, and it showed me the whole contents of /system partition.
But nevertheless, I am not able to get into recovery. When I power down the watch, hold the power button that long after it vibrates 2 times in row, release the power button, the bootloader appears. In internet they say, by just clicking the power button once for a short time will change the selected option to get for example into recovery mode, but when i click the power button, the watch just shutdowns. If i hold it longer it also shutdowns instantly.
So I am not able to get into recovery unfortunately. So it might probably not even be possible for me to flash another rom even if i would have found the pin's for the usb cable right?
Edit²: As I said i debugged using bluetooth and just came up with an idea. I remembered with adb its possible to reboot into different modes...
Reboot to bootloader, reboot normal, reboot to recovery. And rebooting to recovery actually worked I guess...
I got a screen with android buddy and a red warning signal. Guess what's just missing is a cable that can upload/flash the ROM or a custom recovery to the watch.
Now a question, i found an official moto 360 twrp recovery. I guess i cant flash this to the watch's second generation.. ?!
What is missing now is really just the usb connection
...it is preproduction testing unit and it can have little different hardware
How much did u pay for it?
Sent from my m1 note using Tapatalk
RASTAVIPER said:
How much did u pay for it?
Sent from my m1 note using Tapatalk
Click to expand...
Click to collapse
200€. But I got the money back and was allowed to keep the watch, because it didnt match the ebay description.