I really confused about how to configure MMS client in this phone (actually since I use WM5 on my mpx200).
This is the setting for my operator.
Access Point Name : mms.indosat-m3.net
Username : mms
Password : im3
IP address (WAP Gateway ??) : 010.019.019.019
Homepage : http://www.mmsc.m3-access.com
Where should I enter these configuration ???
I'm curently using WM6.1 by GantGoSplat
I downgrade my phone again to WM 5.0 and now the MMS worked.
Related
Can someone please tell me what settings you are using to get your MMS to work? I've on the computer for hours trying to figure it out with no luck.
Please help!
I'm using schaps wm6 3.60 ROM if that means anything
can anyone out there help me?
Can you get GPRS? ie. can you access the internet with your current settings?
Have you tried here? http://mb.softbank.jp/mb/en/product/xseries/htc/x01ht/
Rogers CANADA
GPRS Settings
1. Operator Name & Country : Rogers Canada
2. Network Name : MY ISP
(Name in the Connections Tab)
3. Modem Name :ROGERS GPRS
4. Modem Access Point Name :internet.com
5. Username :wapuser1
6. Password :wap
7. Domain :””
8. Is there a tick in the 'This network connects to the Internet' box :
NO
9. Is there a tick in the 'This network uses a proxy server' box :
NO
MMS Settings
2. Network Name : MY Work Settings
(Name in the Connections Tab)
3. Modem Name :ROGERS MMS
4. Modem Access Point Name :media.com
5. Username :media
6. Password :mda01
7. Domain : leave empty
8. Is there a tick in the 'This network connects to the Internet' box :
NO
9. Is there a tick in the 'This network uses a proxy server' box :
NO
1. Server Name :Rogers MMS
2. Gateway :172.25.0.107
3. Port Number : 8080
4. Server Address : http://mms.gprs.rogers.com
5. Connect Via : My Work settings
6. Size Limit : 300
7. WAP Version : 2.0
Hello Everyone!
Firstly I would like to say thank you for the amazing input you put into this site - I have gone *very* far on the path to learning about my PPC 6800 just from reading past posts.
Problem
When trying to use data services on a Sprint Mogul configured for Alltel - Dialing #777 results in a "Cannot connect for unknown reason" message.
Voice and Text works fine.
Current Setup
PPC 6800 - SPC Reset to 000000 via QPST
oliPro 2.4
Radio 3 42 50
DCD 3 2 6
Alltel Carrier Cab 20080824 (I simply double clicked to install this right?)
PRL: 30031 and 40036 tried
ALWAYS ROAMING (I'm never in an Alltel Area)
Windows Connections settings: Alltel Wireless - #777 - login: [email protected] pass: alltel domain: empty
My Flash Steps
1) hard reset
2) Installed olipro 2.4 (and even tried with no2chem 2 47) via RUU
3) Flashed alltel Stock 3.35.671.9 with Radio via RUU
4) Let customizations run
Data at this point does not work but has (last week!!)
5) install radio 3 42 50 via flash
6) install dcd 3 2 6 via ruu
7) let customizations run
8) double clicked on Alltel carrier 20080824 and installed to device
data says same problem
I've tried a *228 Option 2 (update roam) and Option 3 (activate). No help.
I'm stuck
EPST Settings
Security:
HDR AN: [email protected]
HDR AN pass: my hex esn in all caps
PPP user id: [email protected]
PPP pass: alltel
MIP Default:
nai: [email protected]
mn ha: 101
mn aaa: 3E8
reverse tunnel: enable
home address: 0.0.0.0
primary address: 0.0.0.0
secondary address: 0.0.0.0
ha shared: rzU4LCHIJp+Efdtf (it worked last week!?)
aaa shared: alltel
dmu public key: 0
mn authentication: 0
MIP
mip mode: mobile ip preferred
mobile node ha: disable
send reg retry: disable
dormant handoff: ena
QPST Settings
By putting my phone in DIAG mode and running QPST I have the following settings
DATA
MDR Mode: SVC opt 33 Prefd
Service option: Pre 707
Data qnc - unchecked
data scrm - enabled
Mobile IP
Behavior : simple only
mn auth calculation: unchecked
My Questions
1) am I flashing this correctly?
2) Could someone please verify what my DATA and M.IP settings should be in my QPST section?
3) does my HA shared key in EPST have anything to do with this?
Thanks for any guidance or help in getting me setup - I'm hoping that by making stating all my settings nice and clear we can help others that search in solving their problems as well!
ShaneOMak said:
Hello Everyone!
Firstly I would like to say thank you for the amazing input you put into this site - I have gone *very* far on the path to learning about my PPC 6800 just from reading past posts.
Problem
When trying to use data services on a Sprint Mogul configured for Alltel - Dialing #777 results in a "Cannot connect for unknown reason" message.
Voice and Text works fine.
Current Setup
PPC 6800 - SPC Reset to 000000 via QPST
oliPro 2.4
Radio 3 42 50
DCD 3 2 6
Alltel Carrier Cab 20080824 (I simply double clicked to install this right?)
PRL: 30031 and 40036 tried
ALWAYS ROAMING (I'm never in an Alltel Area)
Windows Connections settings: Alltel Wireless - #777 - login: [email protected] pass: alltel domain: empty
My Flash Steps
1) hard reset
2) Installed olipro 2.4 (and even tried with no2chem 2 47) via RUU
3) Flashed alltel Stock 3.35.671.9 with Radio via RUU
4) Let customizations run
Data at this point does not work but has (last week!!)
5) install radio 3 42 50 via flash
6) install dcd 3 2 6 via ruu
7) let customizations run
8) double clicked on Alltel carrier 20080824 and installed to device
data says same problem
I've tried a *228 Option 2 (update roam) and Option 3 (activate). No help.
I'm stuck
EPST Settings
Security:
HDR AN: [email protected]
HDR AN pass: my hex esn in all caps
PPP user id: [email protected]
PPP pass: alltel
MIP Default:
nai: [email protected]
mn ha: 101
mn aaa: 3E8
reverse tunnel: enable
home address: 0.0.0.0
primary address: 0.0.0.0
secondary address: 0.0.0.0
ha shared: rzU4LCHIJp+Efdtf (it worked last week!?)
aaa shared: alltel
dmu public key: 0
mn authentication: 0
MIP
mip mode: mobile ip preferred
mobile node ha: disable
send reg retry: disable
dormant handoff: ena
QPST Settings
By putting my phone in DIAG mode and running QPST I have the following settings
DATA
MDR Mode: SVC opt 33 Prefd
Service option: Pre 707
Data qnc - unchecked
data scrm - enabled
Mobile IP
Behavior : simple only
mn auth calculation: unchecked
My Questions
1) am I flashing this correctly?
2) Could someone please verify what my DATA and M.IP settings should be in my QPST section?
3) does my HA shared key in EPST have anything to do with this?
Thanks for any guidance or help in getting me setup - I'm hoping that by making stating all my settings nice and clear we can help others that search in solving their problems as well!
Click to expand...
Click to collapse
DMU Key Reset. Either activate an old phone... wait a bit... get it working... then re-activate the new one. Or... call them.... tell them your phone doesn't get data, and you just did a hard reset. They might be able to fix it for you while you are on the phone.
Case Closed!
I called alltel and asked them to look at at performing a DMU Reset - while looking at my account they realized a few glitches (why they did not catch it before I'm not sure) and made changes.
They included:
Updating my Service Class to Simple IP only
Double Checking my AAA Authentication log and realized that a billing issue was not connected (Damn, they should have left this alone )
Thanks for your help!!1
*case closed* !
Concerning DUTCH Vodafone users
When flashing: [ROM][WM 6.5] "Official" v1.00 [XIP/SYS 21854] and you place the sim-card in your phone it will start the connection setup to select you country and operator and it will do some vodafone settings.
These settings DOES NOT work. You CANNOT browse after that using GPRS.
Here are the correct settings which did the job for me, plz correct me if somethings is not correct, i'd verified these settings myselves:
HSDPA Switch: Turn on HSDPA (not off)
GPRS authentication on PAP (not CHAP)
Goto START -> Settings -> 6. Connections -> 5. GPRS ->
delete all entries: and create 3 entrys:
-Vodafone MMS
Connect to: vodafone MMS
Access Point: office.vodafone.nl
Username: vodafone
password: vodafone
pri/sec DNS: empty
Ip adress: empty
-Vodafone Office
Connect to: The Internet
Access Point: office.vodafone.nl
Username: vodafone
password: vodafone
pri/sec DNS: empty
Ip adress: empty
-Vodafone Push Mail
Connect to: Vodafone Push Mail
Access Point: push.vodafone.nl
Username: vodafone
password: vodafone
pri/sec DNS: empty
Ip adress: empty
Goto START -> Settings -> 6. Connections -> 6. PROXY ->
delete all entries: and create 3 entrys:
-Vodafone Office HTTP
Connects from: Work
Connects to: The Internet
Proxy nameort: 192.168.251.150:8799
Type: HTTP
username/password: empty
-Vodafone Office Sock
Connects from: Work
Connects to: The Internet
Proxy nameort: 127.0.0.1:8799
Type: SOCKS4
username/password: empty
-Vodafone Office WAP
Connects from: Work
Connects to: The Internet
Proxy nameort: 192.168.251.150:9201
Type: WAP
username/password: empty
(PROXYS ARE PROBABLE NOT NECCESARY!)
Goto START -> Internet Explorer -> Menu - Tools - Options - Connections:
Automaticlly detect settings: OFF
Select network: The Internet
When using Push Mail configure it using activesync or in windows 7 or higher with: Windows Mobile Device Center.
I'm open for questions and answers.
Good luck and sorry for bad english
Wuwa
Hi,
i am having a problem with the VPN IPSec settings: I cannot enter a FQDN in the VPN Server settings, the input field only accepts an IP address. Does anyone know where the config file is saved so i can try to edit it manually?
Ok. This is a weird one for me. I bought a EVO 3D off of Ebay with a bad ESN. I didn't care about the ESN since I was going to flash it over to Page Plus anyways. So, I flashed it and got everything running for it...except MMS. Talk, Text, & 3G works fine. I tried creating a default APN settings using giffgaffAPN since I couldn't get to the APN settings by going to Menu-Settings-Mobile Networks (option wasn't there). I put in what I found online as the default settings for the new APN. The APN didn't show up in the list but I didn't see the old APN either so I took it for granted that all was right in the world. I tried downloading a pic I'd received earlier via MMS and still nothing. I was still able to surf on 3G still. Can someone tell me what I'm doing wrong? Thanks!
OS: Android 4.03
Dial ##3282# on your dialer and tap edit mode then enter your msl / spc. Then go to advanced. At the bottom you will have the settings option.
On some roms you can directly change mms setting from the message app>settings
EDIT : I see you edited it yourself.
mnomaanw said:
Dial ##3282# on your dialer and tap edit mode then enter your msl / spc. Then go to advanced. At the bottom you will have the settings option.
On some roms you can directly change mms setting from the message app>settings
EDIT : I see you edited it yourself.
Click to expand...
Click to collapse
Thanks for the help! I'm the right place but not all of the options that I need or in the settings. I need to put the following in but username and password or missing. I went ahead and put in all of the info that was available but the MMS still wouldn't work.
Verizon APN settings Android:
Name : Verizon
APN : Verizon or vzwinternet
Proxy : null
Port : null
Username : Mobile [email protected]
Password: vzw
Server :
MMSC : http://mms.vtext.com/servlets/mms
MMS Proxy : null
MMS Port : null
MCC : 310
MNC : 012
Authentication type : Not Set
APN : Not Set
Note: I just found username under data profile but no place to enter in password, MCC, or MNC.
whodatdoug said:
Thanks for the help! I'm the right place but not all of the options that I need or in the settings. I need to put the following in but username and password or missing. I went ahead and put in all of the info that was available but the MMS still wouldn't work.
Verizon APN settings Android:
Name : Verizon
APN : Verizon or vzwinternet
Proxy : null
Port : null
Username : Mobile [email protected]
Password: vzw
Server :
MMSC : http://mms.vtext.com/servlets/mms
MMS Proxy : null
MMS Port : null
MCC : 310
MNC : 012
Authentication type : Not Set
APN : Not Set
Note: I just found username under data profile but no place to enter in password, MCC, or MNC.
Click to expand...
Click to collapse
I think I just figured out a step that I needed to put in. There's a field that says MMS Server URL that's just inside of the advanced menu that's a header like MMSC Setting. I put the MMSC URL into that field and I received those MMS messages that were previously just download. I need to try sending MMS messages now but unfortunately, last night, my SD card failed. I lost 16 gigs of pics (about 3k pics) and movies...including pics of the first time I held my son. Fortunately, most of those are on FB.
Thanks again for all of your help. Hopefully, when I get the new SD card in from IceMonkey.com ( Here's the one I'm getting and there's no referral link so I shouldn't get dinged for this ) and get some of the pics redownloaded, I can test out the send function on MMS.