Hello there! I changed the rom to AP Dual 3 and now the X7500 restart and install all the problem as the first time when the rom launch.
The 3 colours are strange.
Here are some screenshot:
What can I do? Because the rom restart everytime
Thanks!
Read this: http://forum.xda-developers.com/showthread.php?t=408815
cktlcmd said:
Read this: http://forum.xda-developers.com/showthread.php?t=408815
Click to expand...
Click to collapse
Thanks for your answer. I am from Argentina, my english is not good. I tried to read everything but I can't understand how to solve it.
Do I have to download spl 1.2?
To be honest, I don't know. I own a X7510.
I suggest posting your question on the similar thread. I just suggested that thread because the screen description you showed is similar to the other one. Good luck.
By the way, how did you end up with that screen? It might be solved if you flash it again with the original ROM.
mercadocel said:
Thanks for your answer. I am from Argentina, my english is not good. I tried to read everything but I can't understand how to solve it.
Do I have to download spl 1.2?
Click to expand...
Click to collapse
1) check your SPL version. To do this push STRONG the camera button and TOGETHER push the small reset button in the back.
You will see a tri-colour screen , read the model ID ATHE100 (?) and the SPL (1.2? 3.5?) soft reset again to go back. if the model ID is scrambled... you are in trouble. Ask CMONEX help with a PM or follow the instructions from here http://forum.xda-developers.com/showthread.php?t=405604
2) from this thread http://forum.xda-developers.com/showthread.php?t=397518 choose the ROM you want PAY ATTENTION to chose the correct SPL version
3) Follow the link, download the ROM, enjoy
I press STRONG camera en reset but I can't enter in bootload mode, the screen turn grey and says "Loading..."
How can I fix it? =(
mercadocel said:
I press STRONG camera en reset but I can't enter in bootload mode, the screen turn grey and says "Loading..."
How can I fix it? =(
Click to expand...
Click to collapse
Hi
Remove memory card and the sim card from the phone.
Then Vol down+reset (Hard reset).
Then Press strong on camera button+reset then you get the Boot loader.
Then Flash your device's original rom if your device not on SPL 1.2 or SPL 3.5
Good luck
sabes143 said:
Hi
Remove memory card and the sim card from the phone.
Then Vol down+reset (Hard reset).
Then Press strong on camera button+reset then you get the Boot loader.
Then Flash your device's original rom if your device not on SPL 1.2 or SPL 3.5
Good luck
Click to expand...
Click to collapse
Thanks! I solved =)
Thanks for all the help!
Related
i unlock G4 Wizard with this method. and after i flash it with a turkish rom file. it's success and very well working without sim card.
Bu when i insert a sim to wizard, it has locked the ppc. and after i flash it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.
and after the ppc is open but stuck on opening screen. i try to master reset it but i can't. and after i remove the battery and detach the sim.
now the ppc can't open. i try to get it to bootloader mode but i can't. when i press master reset & camera button, nothing happens.
i try different button combinations but it can't open.
edit:
i flash it with RUU MUN program
please help
Oh my god...
Flashing Hard SPL to your device does not mean you can flash any ROM you want. You can only flash ROMs that doesn't have IPL and SPL.
Since CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE (Button's ROM) includes IPL and SPL 1.01, you most likely bricked your device.
in this case what can i do?
can i change the flash of the phone? if yes, hoc much does it?
Help Me I Did The Same
I Have The Same Problem If Theres A Solution Please Help Me!!!...
AYALA445 said:
I Have The Same Problem If Theres A Solution Please Help Me!!!...
Click to expand...
Click to collapse
Alas!
If there cud be a solution,but sorry,its a 'BRICK'.There's no solution except to sell it as parts.
If you are in China, there are places that can replace the flash chip for you. Outside China, there seems nobody do this kind of repair...
[FULLY SOLVED]HELP！！！I cannot log on to OS after flash Titan HARDSPL 2.40
I followed Titan FAQ and used HARDSPL MFG to unlock my Titan. It seems that the phone has been unlocked because there is the data on Tri-color Screen after the complete flashing.
TITA100 MFG
SPL 2.40. Olipro
CPLD-9
However, the Titan won't restart itself and I cannot reset it by myself either! It just freezes on the Tri-color screen and shows the above data. (even after a soft reset/hard reset, it goes to the Tri-color screen)
I am toally frustrated on it. Anyone please please please help me on this issue? This is totally different from the kaiser flashing.
I greatly appreciate any help!!!
Does it say Serial at the bottom of the screen??? If so, plug it into the PC, now does it change from serial to USB???
azclown said:
Does it say Serial at the bottom of the screen??? If so, plug it into the PC, now does it change from serial to USB???
Click to expand...
Click to collapse
yes yes yes that is what it is doing!
unplug the cable, it changes to serial. plug the cable again, it changes back to USB.
Who is your carrier?
At this point you can Flash the radio via the SD card method, OR use the official Sprint Release to get the 3.39 radio on your phone.
azclown said:
Who is your carrier?
At this point you can Flash the radio via the SD card method, OR use the official Sprint Release to get the 3.39 radio on your phone.
Click to expand...
Click to collapse
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
dewydewy said:
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
Click to expand...
Click to collapse
no not necessarily, while its true your stuck on the tri-color screen, this is only a minor problem caused by unlocking, there's a topic somewhere that explains why it does this, and a fix. But before you try "fixing" it, you can now flash your phone to some custom ROMs, like DCD. Update its Radio and ROM, And try soft resetting it again. If its still stuck... ill see if i can find the page..
right so I'm back and found what you were looking for, what your experiencing is being stuck at the Bootloader, Ive had this problem before when unlocking my phone as well.
Here's the Wiki.
http://wiki.xda-developers.com/index.php?pagename=TitanProblems
dewydewy said:
Carrier is Telus. I am in halifax, Canada.
what does that mean by the freezed tri-color screen? is that mean the phone is failed unlocking?
Click to expand...
Click to collapse
No, the phone is unlocked, however it will not function because you have the wrong radio and rom on it.
Like I said, you have 2 options.
1) Download the latest Official Sprint Release or
2) Upgrade your radio using the SD method.... <-- preferred
Can you take your microSD card and format it FAT32, 1k cluster....?
Still don't understand...
Without being able to load into the Pocket PC's OS. How could you flash a new radio and a new OS?
P: My device is stuck at the Red, Blue and Green Screen?
S: To exit the bootloader, press the reset. You may need to reflash the Radio/Operating system ROM
Is the one you just mentioned? I have not flash any rom or any radio yet. The titan just freezes there before I take the next step.
dewydewy said:
P: My device is stuck at the Red, Blue and Green Screen?
S: To exit the bootloader, press the reset. You may need to reflash the Radio/Operating system ROM
Is the one you just mentioned? I have not flash any rom or any radio yet. The titan just freezes there before I take the next step.
Click to expand...
Click to collapse
PM me your aim or yahoo or msn screenname and i'll walk you through it
coffey_joshua said:
PM me your aim or yahoo or msn screenname and i'll walk you through it
Click to expand...
Click to collapse
replied!
Thank you heaps!!!!!
Also, this thread can help you alot....
Start at STEP 5....
http://forum.ppcgeeks.com/showthread.php?t=17667
Thank you, Thank you all. Especially coffey_joshua, he is definitely the savior, lol.
I just dont know how much I should appreciate here. Thank you heaps everyone! You guys are the best, kindest and most talented people I have never meet in any forum!
dewydewy said:
Thank you, Thank you all. Especially coffey_joshua, he is definitely the savior, lol.
I just don't know how much I should appreciate here. Thank you heaps everyone! You guys are the best, kindest and most talented people I have never meet in any forum!
Click to expand...
Click to collapse
this is in partly due to the fact were practically in love with our phones now, and don't mind sharing that kind of appreciation we have grown accustomed to.
That or were just addicted
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Update - I just tried this:
http://forum.xda-developers.com/showthread.php?t=326953
but without success. I get an Error [260] and the entire process stops.
Anubis1965 said:
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showthread.php?t=405814
lakeman said:
look here
http://forum.xda-developers.com/showthread.php?t=405814
Click to expand...
Click to collapse
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Anubis1965 said:
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Click to expand...
Click to collapse
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
If you see in bootloader mode ID showing somenting different than ATHE100 the solution is HERE http://forum.xda-developers.com/showthread.php?t=405814
I had the same problem! whell restart your pc and then connect the device to it. now start flashin an spl 1.20 rom. i did it and it worked! I hope i works for you too.
Cheers, Hirad
lakeman said:
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
Click to expand...
Click to collapse
Thanks - already tried!
When I reset/hard-reset the phone (tried many ways) I see a garbled boot image (with random pixels here and there)... It is definitively not the usual bootloader with the information about the various ROM components and the "USB" text at the bottom.
Anubis
Solution!
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
You are right and this is what sergiopi and I were referring to , specifically this post
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
We were refering to the whole thread so you could learn the background.
However you are incorrect in your advice about how to enter bootloader
All you need to do is hold in the camera button and reset
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
Thanks - you are giving me some hope! I am on a business trip now and my Athena is at home, but I will try that as soon as I am back
Anubis
Hi Guys,
I've been using the ROM from Michy the R4 edition for some days without experiencing any problem and now it occurs that phone function stoped working for unknown reason ! just like that.
Impossible to enter PIN number the connection manager refuse even to open.
I've tried to install different ROM to see if it could change anything but nothing has changed.
I've also no more description of the RADIO I'am using in the about file.
Please help me to save my lovely brick !
i can help u
hi pal i can help u i also had faced the same problem
ur radio board has been dislocated
pm me to make ur baby alive
u an also contact me on phone at +919823291495 or messenger
at [email protected]
What data you have in BL mode ?
callmelolo said:
Hi Guys,
I've been using the ROM from Michy the R4 edition for some days without experiencing any problem and now it occurs that phone function stoped working for unknown reason ! just like that.
Impossible to enter PIN number the connection manager refuse even to open.
I've tried to install different ROM to see if it could change anything but nothing has changed.
I've also no more description of the RADIO I'am using in the about file.
Please help me to save my lovely brick !
Click to expand...
Click to collapse
Hi
Please download the Michy R4.1 and update it it will work. I had the same problem. My advice is "do not use password or pin while you are testing the new rom"
1. Do a hard reset By Vol Down+ reset hole press
2. Get into boot loader By Camera button pressed + reset hole press until you see the tricolour screen.
3. Then flash R4.1
Good luck
Hi Sabes,
I tried to install the 4.1 Rom and it loaded well. I had the boot screen where nothing was writen after the "R" of radio and then I went to the frist setting screen. It then asked to reboot to customize and since that moment black screen. The power led is on and nothing more...
**** ! it sounds like its definitely dead !
I don't understand anything cos I did nothing wrong, no droping, no tweaks, everything was working fine up to some day the phone function stoped working for unknown reason and now I have a black screen.
I have 1.2.
Boot screen shows : Rom = None
I have managed to reinstall the ROM from Michy the R4.1 version and it powers on again.
The problem remain the same = no phone function
When I get to Device Information I have nothing writen after Radio version and Protocol version.
callmelolo said:
I have 1.2.
Boot screen shows : Rom = None
I have managed to reinstall the ROM from Michy the R4.1 version and it powers on again.
The problem remain the same = no phone function
When I get to Device Information I have nothing writen after Radio version and Protocol version.
Click to expand...
Click to collapse
I have a couple of ideas but I would like you to get into the bootloader screen and tell us what you can see there
I have
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20. Olipro
I've been trying the TTY thing but.... :
start NB image download
Fail to synchronize with the host (1)
callmelolo said:
I have
ATHE100
IPL-v1.00
ATHE100
SPL-v1.20. Olipro
I've been trying the TTY thing but.... :
start NB image download
Fail to synchronize with the host (1)
Click to expand...
Click to collapse
I think you have somehow lost your radio or it has become corrupted
Do you have one of the shipped roms?
Try flashing this as i think it includes a radio
even AP3 may have a radio included in the RUU
Flash this while you are in bootloader.
Or you could flash radio 1.58
I've been trying to flash the 1.58 this morning and I was stuck on 0%
I will get to the wiky and try to download the original Rom for my Athena.
Thanks
callmelolo said:
I've been trying to flash the 1.58 this morning and I was stuck on 0%
I will get to the wiky and try to download the original Rom for my Athena.
Thanks
Click to expand...
Click to collapse
Just a thought
have you removed your sim and sd card?
Yes I did...
Just finished downloaded the original Rom I will keep you posted with the results...
First of all, Hi!
Now, how do I clear my nike to the point where it has nothing on it?
I need to do this because I got stuck in the process of flashing it with HARDSPL 1.22 that I need in order to flash a new rom!
I tried everything, I followed the guide on how to do HardSpl, but got stuck at step 8 of the tutorial, the process bar is constantly at 0%, and followed by recovery steps!
I do not need them because everything works just fine, only with the original rom still on!
So I want to flash a rom, but am unable to!
Please help me!
Even if my solution is deleting everything ( I do not mean a Hard Reset- Did that 10 times ) and starting from 0!
But this is one thing I never did, and do not know where to start or what to do!
So any good soul out there willing to help, please do so!
Thanks in advance!
Ok let's try to help, can you tell us more details about your phone, model 16 or 20 keys, rom and radio.
If this is not clear just send me a pm
Regards Rataplan
Thanks, mine is a 16 key version.
Radio 1.65.28.25
Rom: 2.09.405.1
Rom date: 30.08.2008.
Protocol version: 25.98.40.07H
And I did the first few steps of flashing the HardSpl
and now it says SPL 1.22
and further more, on start up screen it says "TEST ONLY NOT FOR SALE"
BTW: I was looking of flashing your ROM but as I said, no can do!
HELP
Ok from what I see it looks to me that you already flashed a rom, just one question is it telling SPL 1.22 or SPL 1.22 Hard
just SPL
That is my problem!
Any solution!?
You need to start all over again, do you have a Niki, you can see that under the battery
Okay just read your post in the other thread, that cleared a lot of things, just do it all over again and use 1.15 instead of 1.22 maybe that will work for you, btw from what I can see you didn't do anything wrong, I also flashed directly the 1.22 and from me that works.
Just keep me informed how it goes.
Regards
The phone is niki100
There is no simlock!
What do I need to do?
Refer me to a tutorial, or just tell me everything here?
And thank you for the help so far!
Edit:
OK, I did what you said, and so far works!
But, could you please explain to me a couple of things!
1. download the attached files DONE
2. REMOVE SIM and SD CARDS !! DONE
3. connect usb cable DONE
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!) DONE
5. after a few seconds "USB" appears on the display DONE
6. unplug and replug the usb cable DONE
(OPTIONAL, better to skip it! step 7. if you only want to test the sspl try flashing the attached splash screen by running ROMUpdateUtility.exe from flash-splash-niki) SKIPPED
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
AND NOW here is my question, in the file FLASH-USPL-NIKI there is a uspl-1.16-nike.nbh file, but here in this step it says to flesh the 1.15mfg(wich I downloaded), so do
i have to delete the 1.16 and replace it with the 1.15mfg or what?
9. after installing the hardspl you can flash any rom (rom cook project here)
Okay I think I kow what you mean, you must flash the 1.15mfg, do not copy it to your phone, you don't have to delete the 1.16.
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
I need help, i have flashed a rom but now my niki stops at the radio details. It doesn't boot to windows mobile.
How do i reflash a working rom now?
How long have you waited before taking out the battery?
It takes a while to load!
It takes a while to load yes, but 5-10 minutes is to long for it to start to boot.
It has passed 1 hour now.
Anyone knows how can i fix my niki?
2 die 4 said:
EUREKA, it worked!
Flashed your F01-10 rom!
Now I only did the 1.15 HARD Spl
Please suggest to me a radio?
I tried flashing the Radio_1.71.09.01_25.75.40.02K and it got to 100% and then said FLASH WRITE ERROR, so I was stuck wit the old radio!
AND OMG, THE ROM IS WONDERFUL
Thank you so very very much!
Click to expand...
Click to collapse
You're welcome for the rom, about the radio if you want to try the 1.71 radio you have to go back to an older radio before you flash the 1.71.
I suggest to use a 1.5.. radio, that will do the trick.
For now you can always put Hardspl 1.22 on your phone, some people are recommended that if you flash a wm 6.5 rom, personally I don't see any difference.
Btw The radio I use is 1.65.29.22
Regards
masterxiter said:
It has passed 1 hour now.
Anyone knows how can i fix my niki?
Click to expand...
Click to collapse
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Rataplan said:
Hmm, that's a long time without a phone , did you already try a hardreset, just turn the phone off, and turn it on by pressing the power and the send and end key on the dame time, I think that will do it.
Just keep me informed.
Regards
Click to expand...
Click to collapse
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
masterxiter said:
Yes it enters restore mode. If i have the usb cable, when the restore finishes, on the pc it says "unrecognized usb" / Unknown device. I reboot the phone and its the same.
Click to expand...
Click to collapse
hey dude
y dont u flash the original rom of htc nike once and then retry?
Rataplan said:
Hmm, okay this will be diffucult, I've read you flashed a rom and after that you get this issue, just a few questions did you cid unlock your phone, and is the bootloader still there. (that is the 4 coloured screen with the spl info)
Click to expand...
Click to collapse
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04
B 04
R 1.65.28.25
G 25.98.40.07W
D 2.12
What happened was, i had an working cooked rom flashed in my phone. I was working with it for about a month.
yesterday i flashed with another one. It got me 100% rebooted and voilla doesn't pass the spl boot.
masterxiter said:
Yes i have both.
I allready change those 4 colors for an image, lol but ok i have the spl info:
M 04 R 1.65.28.25
B 04 G 25.98.40.07W
D 2.12
Click to expand...
Click to collapse
Ha ha yeah that would be nice if we could replace that for an image.
Okay, connect it to your computer when you're on the 4 coloured screen and see if it connect then, in the phone you see serial changing in usb, if yes just flash your original rom.