Ignore the title, looks like a mis-aligned pin and a coincidence.
-Stoney
Sounds like a coincidence to me. I really don't see how it's possible for that software to have done that.
anythingbutmine said:
Sounds like a coincidence to me. I really don't see how it's possible for that software to have done that.
Click to expand...
Click to collapse
Everything worked fine until that program crashed my phone (was able to charge via A/C adapter/usb cable/sync etc). I was able to replicate the crash (and only a hard-reset makes the O/S operational again).
perhaps it could have been a coincidence.... i do have the $6 a month insurance... i'm thinking i should try to get the Radio/ROM back to stock and just ship this f*cker back to verizon.
I got the verizon boot screen to appear, but it hangs.
Good news is the proper radio shows up,
bad news is these still appear:
bootloader 2.40.Olipro
ROM Version: 3.2.3
I can't seem to find a microSD version of the post-GPS update relocker (back to factory). The stock rom installation just hangs =(.
I'm guessing this would be a red flag for a warranty return?
Edit/Delete Message
ssstonebraker said:
I can't seem to find a microSD version of the post-GPS update relocker (back to factory). The stock rom installation just hangs =(.
Click to expand...
Click to collapse
flash back on a ROM that is supported, then run the titan relocker, and use microSD to flash back to stock after relocking...
Read instructions and download the Stock ROM and relocker from:
http://wiki.xda-developers.com/index.php?pagename=TitanStockHome
I'm going to attempt that now.
Actually i noticed one of the pins in the mini USB port wasn't aligned with the others, i moved the pin where i thought it should be, but i'm still not getting any power.
Does anyone have a high resolution picture of the mini-usb port?
I am now successfully running:
Phone: xv6800
ROM Version: nueROM v2.1 build 5068.rar
Radio Version: 3.42.02
1. i reflashed 3.42.02 (http://rs333.rapidshare.com/files/124696893/Titan_Radio_ROM_3.42.02.rar) via micro SD.
2. Flashed the RUU_signed.nbh from RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship
3. Rebooted before customization
4. Installed ftp://ppcgeeks.com/Titan/Users/No2Chem/nueROM v2.1 build 5068.rar from Micro SD (then ran verizon cusomization)
However, i still don't have usb power/sync.
I'm going to mess with the pins per these pics that were given to me from ppcgeeks:
http://www.4winmobile.com/tg/Xda_Trion/008.jpg
http://www.4winmobile.com/tg/Xda_Trion/014.jpg
I just took a picture of my mini-usb port on my HTC Titan (xv6800). I'm not sure what's wrong with it, i think it is a pin issue:
http://stashbox.org/166879/xv6800_busted_mini_usb.PNG
any advice on what to move would be appreciated!
Thanks,
Stoney
What a coincidence. My port must have broke just before I flashed my phone via sd. When I attempted to sync after the flash, I couldn't charge or sync. I assumed it was the flash and re flashed several times till I finally looked at the port. The port design is not the sturdiest, especially for considering that it is intended for headphone use along with the usual charging/syncing. It's a set of pins with a unattached and easily broken plastic guide underneath. It's all too easy for the plastic guide to break or bend, exposing the pins to easy breakage/ bending. My cheap $90 Pharos GPS's port has contacts instead of pins embedded in the guide, seemingly a far more durable design. I swapped out my phone with Sprint. When I explained the problem to the tech, she didn't even look at the phone and immediately set up the swap. I took this to mean that this was an extremely common problem with the Mogul/6800. Good luck!
From your pic, I doubt you'll be able to straighten that pin without it breaking. Even if you did, it would likely break soon after. If Verizon won't swap and/or is high priced for the repair, http://www.pocketpctechs.com/main~unit~HTC_Mogul-906~area~repairs.htm
jph8tr said:
What a coincidence. My port must have broke just before I flashed my phone via sd. When I attempted to sync after the flash, I couldn't charge or sync. I assumed it was the flash and re flashed several times till I finally looked at the port. The port design is not the sturdiest, especially for considering that it is intended for headphone use along with the usual charging/syncing. It's a set of pins with a unattached and easily broken plastic guide underneath. It's all too easy for the plastic guide to break or bend, exposing the pins to easy breakage/ bending. My cheap $90 Pharos GPS's port has contacts instead of pins embedded in the guide, seemingly a far more durable design. I swapped out my phone with Sprint. When I explained the problem to the tech, she didn't even look at the phone and immediately set up the swap. I took this to mean that this was an extremely common problem with the Mogul/6800. Good luck!
Click to expand...
Click to collapse
very interesting, i agree they need to do something about the design of these ports. Never again will i just jam in the usb cable.
Here's my fix....
YES!!! I TOTALLY FIXED IT! (with screenshots):
http://stashbox.org/166905/xv6800_fixed_mini_usb.png
I also broke my port. I went to plug in my charger got a hint of resistance and when I pulled the charger out I noticed one of the pins was laying flat against the back of the mini USB port. Well I tried go get a small knife and pry the pin back only for it to break. I was completly screwed. Now I have to charge my batteries and just trade out.
ssstonebraker said:
very interesting, i agree they need to do something about the design of these ports. Never again will i just jam in the usb cable.
Here's my fix....
YES!!! I TOTALLY FIXED IT! (with screenshots):
http://stashbox.org/166905/xv6800_fixed_mini_usb.png
Click to expand...
Click to collapse
GREAT JOB! Congrats! You also have the most scratched up port I've ever seen . Hopefully, it will hold up. The plastic guide that is now bent away from the pins and likely loose like on my old Mogul isn't like that on a new unit and the straightened pin is weak at the bend. Be very careful using the port.
ssstonebraker said:
very interesting, i agree they need to do something about the design of these ports. Never again will i just jam in the usb cable.
Here's my fix....
YES!!! I TOTALLY FIXED IT! (with screenshots):
http://stashbox.org/166905/xv6800_fixed_mini_usb.png
Click to expand...
Click to collapse
your usb looked like that and you thought software did it?
ssstonebraker said:
very interesting, i agree they need to do something about the design of these ports. Never again will i just jam in the usb cable.
Here's my fix....
YES!!! I TOTALLY FIXED IT! (with screenshots):
http://stashbox.org/166905/xv6800_fixed_mini_usb.png
Click to expand...
Click to collapse
For what its worth, here is pics of mine. Doesn't have raised pins like yours?
ih8aol said:
For what its worth, here is pics of mine. Doesn't have raised pins like yours?
Click to expand...
Click to collapse
can you post a high-res version of those pictures via stashbox.org? Are you saying that your pins touch that black piece?
ssstonebraker said:
can you post a high-res version of those pictures via stashbox.org? Are you saying that your pins touch that black piece?
Click to expand...
Click to collapse
Here you go!
http://stashbox.org/168432/DSC_0006.JPG
http://stashbox.org/168431/DSC_0005.JPG
http://stashbox.org/168428/DSC_0004.JPG
ih8aol said:
Here you go!
http://stashbox.org/168432/DSC_0006.JPG
http://stashbox.org/168431/DSC_0005.JPG
http://stashbox.org/168428/DSC_0004.JPG
Click to expand...
Click to collapse
I have the RAW versions of these too but they roughly 10mb each
ih8aol said:
I have the RAW versions of these too but they roughly 10mb each
Click to expand...
Click to collapse
Thank you for posting those. I zoomed in on the portion i was interested in (from your photo) and it is still a little fuzzy http://stashbox.org/168469/mini_usb_1299x729xfuzzy.png.
Anyway I could get a high rez (no fuzzy) png or RAW of just the mini-usb port? I'm thinking the raw could be thrown up on rapidshare or something.
BTW your pics look great, thank you very very much!
ih8aol said:
For what its worth, here is pics of mine. Doesn't have raised pins like yours?
Click to expand...
Click to collapse
It's not that the pins are raised, it's that the plastic piece (guide?) is not attached to the pins and may break and/or become loose exposing the pins to damage. Cheap design from a company that knows how!
I am not at all impressed with HTC's build quality, when my USB port broke I also had the dreaded white spot and a failing keyboard. When the time comes to replace my Mogul, I 'm going to be looking to avoid HTC and WM! I've had several Windows Mobile and WinCE PDA's and phones over the past 6-7 years and they still can't figure out how to keep the thing from turning on by itself periodically. Hopefully, my new replacement Mogul will last long enough for that phone to be developed. I'll even consider joining the cult of Jobs!
You mention the dreaded white spot. How common is this? VZW just sent me a refurb for mine and it also has the same white spot I complained about on the one going back to them. I have seen other threads on Howards mentioning it but I am course how bad the issue truly is. My coworker has a 6800 with no white spot and two other people have Moguls with no white spot. I must have the luck for getting this.
Related
I am not quite sure as to the variation of included accessories from carrier to carrier but this is a question to at least the Tilt 2 owners and anyone else who's Touch Pro 2 came with that handy charger which has on one end a small block housinga flip up wall plug and on the other a female USB connection, this came with an USB to mini USB cable. The reason I ask is that after purchasing mine in February the mini end to the cable has completely come apart. It actually started within weeks of getting the phone. When I saw what was happening I wrapped it with some splice tape thinking it would be fine, but nope. The end fell out the other day and I was shocked to find that the small metal end was seated into the decidedly softer plastic plug in no more than maybe 1/32". How is something that is the junction for a lot of force anytime one moves the phone supposed to last with this kind of construction. AT&T says they warranty everything in the box? Nope. They will give you a wall charger that they retail for $29 as opposed to sending you the cable which retails for $10 less. My suspicion is that they are well aware of the fragile nature of this cable and so would rather you have something less likely to need replacement, at least while one is still under warranty. So I was curious if others have experienced this and if so, what did you do? Is there something to replace it with that is built better? OEM or not, I would love to know. I won't even go into what HTC said, but lets just say they are of a split mind on what to do.
I don't understand when you say that part is under a lot of force. I just don't see this with normal use.
Cords in general are not known for being durable, and prone to failure. But I agree that failure after 3 months is ridiculous. I've had mine since October, and it works fine. I also have the original cable for the old Tilt, which is 2-1/2 years old now, and well as the old charger (cord is not detachable). Admittedly, I probably don't use the newer USB cable as much as others, since I have these old accessories, which are still used with my Tilt2.
It sounds like ATT is willing to give you a new charger (with non-detachable cable), but not a new cable? That does seem odd. If you need a new cord, get one from Amazon or similar, it cost about $3.50 shipped.
http://www.amazon.com/HTC-Cable-Shadow-Diamond-myTouch/dp/B002CZQ2IK/ref=sr_1_1?ie=UTF8&s=wireless&qid=1274720016&sr=8-1
im in the same boat as OP. Althought his seems to have lasted longer, LOL. Mine started to pull away from the usb b type end after the second week of having the device. Lucky for me i had some electrical tape and as soon as i noticed it i wraped it up good. I also have pleanty of usb to usb b cords laying arround seeing as i own a ps3 also. If you have any you can just use them they fit quite well and work fine.
redpoint73 said:
I don't understand when you say that part is under a lot of force. I just don't see this with normal use.
Cords in general are not known for being durable, and prone to failure. But I agree that failure after 3 months is ridiculous. I've had mine since October, and it works fine. I also have the original cable for the old Tilt, which is 2-1/2 years old now, and well as the old charger (cord is not detachable). Admittedly, I probably don't use the newer USB cable as much as others, since I have these old accessories, which are still used with my Tilt2.
It sounds like ATT is willing to give you a new charger (with non-detachable cable), but not a new cable? That does seem odd. If you need a new cord, get one from Amazon or similar, it cost about $3.50 shipped.
http://www.amazon.com/HTC-Cable-Shadow-Diamond-myTouch/dp/B002CZQ2IK/ref=sr_1_1?ie=UTF8&s=wireless&qid=1274720016&sr=8-1
Click to expand...
Click to collapse
What I mean by force is imagine that point where the mini usb meets the phone as a lever point. So when the phone moves at all, you go to pick it up you bump it,what have you, that is where all of the stress forces will be at play. Considering that point is just a tiny piece of metal and plastic that is only inset about 1/32" what can you expect. The new versions have been redesigned, si I am sure they know. I am also pretty sure this is why neither HTC nor AT&T will carry them in their warranty department. In fact, AT& T doesn't deal with Tilt 2's at all at their service centers. Funny that HTC passed Apple in sales this quarter but might have forgotten Apples hard learned lesson that they received when it was realized that the iPod's battery could not be replaced. The Phones are great, the accessories they by from someone else ordinarily so they are hit and miss
And yeah 1 L0v3 my HtC, I just learned that any mini USB will do. I thought that the ends were proprietary and so the would be hard to find but the different shape fits afterall which is what I am using now.
I have never used mine. I've used my old Motorola charger from day one.
nerv666999 said:
What I mean by force is imagine that point where the mini usb meets the phone as a lever point. So when the phone moves at all, you go to pick it up you bump it,what have you, that is where all of the stress forces will be at play.
Click to expand...
Click to collapse
Yep, that's what I figured you meant. Just doesn't seem like much force to me at all. Sure, cables have a stress point right at the plug, and that is where almost all cables go bad eventually. But if your device is just sitting there, plugged in, I don't see how much stress is being applied to it, even if you bump it.
redpoint73 said:
Yep, that's what I figured you meant. Just doesn't seem like much force to me at all. Sure, cables have a stress point right at the plug, and that is where almost all cables go bad eventually. But if your device is just sitting there, plugged in, I don't see how much stress is being applied to it, even if you bump it.
Click to expand...
Click to collapse
I empathize with the OP. I have thrown away a number of older cables due to short circuits at that junction. It no so bad, unless it shorts out during a flash... :eek At any rate, I now wiggle them before initiating a flash. I also bought new cables with the HTC connector and no longer use mini usb.
I have a number of 'antique' cables and chargers from my 6800 days and a number of newer ones. All are working just fine.
Thread for hardware mods
POSTING INTERNAL tf101 pictures
like 3g dongle ? internal sd cards? ssd?
removing the battery for 2 HDD 500go?
finding sd cards hubs? usb to sata cables?
? there is a place in the tablet for a 3g dongle?
there are 2 screws under the upper rubbers and the dock open easy
there is a lot of spaces avaible
My MIFI might actually fit in there, all I would need to do is supply it power somehow.
I'm no hardware engineer though, but if thats possible it would save you from the driver issues with a 3g dongle.
I wonder if it would be possible to check which pins from the adapter connect to USB - so we can make DIY USB adapter for those without a dock.
hmm adding an hdd would be very interesting, sata won't be very hard, powersupply will be.
Sent from my O2x with CM7
This is what I was looking for, looking to do some mods to the dock.
Thanks Markolino72.
Internally mount and wire a 32gb memory stick to the USB port so you get a 32gb hard drive added whenever you dock It might even have enough room for a portable USB hub so you don't lose use of the external usb port?
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
ydnality said:
does anybody think it will be easy to make a DIY dock fix for those with battery draining issues like me?
It seems like it would be relatively easy - just make a switch to either connect or disconnect the cords coming from the docking point.
Or even better, maybe if you put the correct microcontroller in there you can have it switch the pins to floating, if it senses that there is no tablet connected (not sure about the details though)...
Click to expand...
Click to collapse
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Regards.
In regards to the hardware mods, that really looks amazing. Would love to put in my mifi there as well, attach it via USB to charge = your own 3g model Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well. Only a few thoughts.
Maybe a little modding you could get the mifi to power on only when the dock is connected (remove the battery of the mifi?) so that when it powers on it'll power on the mifi as well.
Click to expand...
Click to collapse
it's a good thought but the mifi I have (novatel 2200) wont work without the battery, for some reason if the battery is bad or removed you cannot run usb, it must be the way they have the power run through the battery or charging. Not sure if all are like this or not.
andrewklau said:
Have you seen the post in the General forum (2nd page now I think)? Posted by Asus_USA themselves, if you prove the 6 steps that your dock has the issue you can get a new one! I really do hope that I can get mine exchanged, waiting on a reply from my local service center..
Click to expand...
Click to collapse
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Surprising how much wasted space there seems to be in the dock -- it's nowhere near as tightly packaged as the tablet itself. Looks like Asus can optimize the size or fit some more features in future versions, if they want...
Let me see if I am thinking correctly...Your saying using something like mifi installed via USB wires (will it be always on?) then connect via WiFi on your transformer? So basically your putting the mifi in a case that can never be opened without a screwdriver? I guess one would always have access for your other devices as well as long as the TF is in the vicinity.
P.S. I think I think this is a good idea, not decided though. I like to think of it in a real world application.
there is another post with a guy putting in an SSD, but it bulges at the keyboard. A 32g SD card would be nice.
Sent from my Transformer TF101 using XDA Premium App
typci said:
I talked to the Asus service rep about it. They currently won't give you a new one since they have a hardware upgrade to fix it. If you wanted a new one you needed to do before they solved the problem. I'm waiting on the upgrade part to be delivered for for mine. Should in a few days.
A switch should theoretically work. The guy at the service center said the replace something that goes into the hinge of the dock. Looking at the teardown pics, you can see a wire goes into each side of the hinge, so I think they replace the wires and maybe make a new connection somewhere on the dock.
Click to expand...
Click to collapse
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
tanguita said:
You are getting the replacement part? bought mine on the US, but live in chile... would really like to somehow get the part that needs to be replaced and do it myself
Click to expand...
Click to collapse
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
knoxploration said:
There's very little chance they'll give anybody the part, and nothing in the previous person's post suggested they're doing so for him.
Talk to Asus Chile and get it serviced by them:
http://www.asuschile.cl/
http://latin.asus.com/Static_WebPage/Service_center_chile/
Click to expand...
Click to collapse
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
tanguita said:
Well I ended up calling them. I would have to ship the dock to "someone" in the US, have them ship it to the repair center, fix it, ship it back and then ask that "someone" to ship it back to me... sooo, I'm basically screwed... I ended up with a nice 150US paperweight (not even considering the horrible light bleed on the transformer).
Click to expand...
Click to collapse
Yeah, actually, I hadn't realized that but it does say it clearly on the product warranty page:
"Brazil and South American countries don’t support global service"
http://support.asus.com/warranty.aspx?SLanguage=en&p=20&s=16&m=Eee Pad Transformer TF101
took mine apart also and there is quite a bit of room.
i plan on putting a 128gb usb flash drive inside the dock and soldering onto the usb connections once i get all the bits in.
Any bigger pictures? Are the screws under the rubber feet?
just two screws under the rubber feet near the hinge then it just pulls apart from the top
had to take mine apart as the spring/clip mechanism for the sd card wouldnt lock the card in.
now the card is stuck in with no nails haha a simple fix.
This is good news. I hacked a Crystal HD decoder card (pcie), USB wifi dongle, a logitech nano receiver, and a 4 port micro usb hub (from a touch screen setup) into a Dell mini 9 and there was absolutely no room compared to this.
They even have covers for the USB ports, so if you remove a header and solder wires up you just have to hot glue / epoxy that cover from the back and you are money. Looks clean and stock.
I have an old 64 GB thumbdrive that might find a new home. Maybe a 1.8" usb HDD would fit in there with the battery, without the battery who knows.
Hello , When I first Purchased my Evo 3D, I noticed that any usb cable attached to it would never fit snug it always had movement like wiggled alot. I should have exchanged it but didn;t think it would eventually lead to serious damage until now, well, somehow the first pin on the right broke off and checking online with research it apparently is the +5 of the usb. Which basically screwed me.
I don't have much of an issue with no longer having the usb data sync ability since I can just use a micro SD adapter, and I have an External Battery Charger from Radio shack which helps because I can just charge the batteries with that and insert in my evo3d But the issue I have now is I realize i rely on the 4G tethering ability which i use constantly and it has become a pain to have to run and switch over batteries so my wifi tethering can maintain my computers online.,
Anyway so noticed a few evo 4g mods online where the person would solder two wires one to the negative and other to the 5v positive where the usb is located and then shape the wires nicely and make a custom usb hole somewhere else on the phone and eventually have a usb charging ability similar to one of the attached pictures ( for evo 4g of course not for the 3d)
So anyway i would like to try something similar where i can just locate some solid solder points on the phone and wire up two 5v and ground wires and relocate a custom usb slot somewhere else on the phone, Below is also some zoom closeups of the evo 3d board so my question is any advice to where I can solder the 5v and ground to, I am clueless to where and what points i should try the underside of the usb slot is all metal so seems like not able to solder there maybe on one of the little chips or something perhaps
,, thanks for any help
in reference to the attached images:
the one with the 5v writing is for an Evo 4g Not 3d But Im putting this picture i found online just to give a similar idea of what i need to find on the 3d
the one with the wired shell mod us just Another photo online of what I want to do but once again need the solder points
the other two are the best closeup pictures I could find of the 3d which maybe someone can just point out to me the locations by looking at it, I will take clear zoomed in photos if needed when I have access to a camera at home
thanks anyone for your help!
Why don't you just take it to Sprint and have them repair it? They'll do it for free.
Not from I heard. They charge 100 to fix it. And not even sure they would give me a loaner phone in the meantime. Also , I went into RADIOSHACK and showed and.spoke to one of the reps and he.told me.I wouldhave to pay unless I had their extended warrantee.. I noticed a resistor like chip above.and in front of where the 5v pin is.I wonder if I can solder on that
Sent from hell
suddene said:
Not from I heard. They charge 100 to fix it. And not even sure they would give me a loaner phone in the meantime. Also , I went into RADIOSHACK and showed and.spoke to one of the reps and he.told me.I wouldhave to pay unless I had their extended warrantee.. I noticed a resistor like chip above.and in front of where the 5v pin is.I wonder if I can solder on that
Sent from hell
Click to expand...
Click to collapse
Call sprint and talk to a supervisor. They will send you a new phone or set up repair for free. Call and hang up twice, then call again to get sent directly to a supervisor.
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
suddene said:
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
Click to expand...
Click to collapse
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
xkravenx said:
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
Click to expand...
Click to collapse
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
suddene said:
Unfortunately me being a tinkerer ended up breaking off the ground pin and was not able to get serviced , even tried the supervisor and no go, I tried another radioshack and sprint store and of course they noticed it was opened so screwed me out...
anyway,, I taken some fair quality images of the board surface. maybe a +5v location can be pointed out from the images? thanks again
Click to expand...
Click to collapse
xkravenx said:
I know this is old. But did you ever figure it out? I need a 5v+ location as well. I want to do the inductive charging mod on the 3D.
Click to expand...
Click to collapse
bronx623 said:
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
Click to expand...
Click to collapse
PLEASE PM me.. those fo you with a broken port, I might have solution for you (nothing shady promise just trying to help where I can, I'll explain once I'm PM'ed). The other guy if all your trying is inductive charging sorry LOL
bronx623 said:
Instead of making a new thread, I figured I would add to this... I too am trying to mod mine with inductive charging, unfortunately my hands are a little too shaky to solder to the point that I discovered to be continuous with the +5v on the usb port.
I can't really find a clear picture of the PCB anywhere otherwise I would show you, but its about a centimeter or two down from the top left when you open your phone, run your multimeter through those points and you'll find it.
I guess I came here looking for another point..
Click to expand...
Click to collapse
Hmm thanks. I will try it when I open the phone. The soldering point should be bigger than the micro-usb pin I would hope.
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
alcapone1130 said:
Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
First, check for disconnected or loose cables inside the gTab.
Next, if it isn't a HW fault like loose cables, then connect the USB cable to the gTab and run this ADB command (you will have to install and set up ADB if you haven't already done so):
Code:
C:\SOME\PATH> [B]adb shell "echo -n 1 > /sys/devices/platform/tegra_touch/calibration"[/B]
Digitizer Cable/Connection
alcapone1130 said:
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
aabbondanza said:
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
Click to expand...
Click to collapse
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Where is the break?
alcapone1130 said:
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Click to expand...
Click to collapse
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
aabbondanza said:
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
Click to expand...
Click to collapse
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
alcapone1130 said:
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
Click to expand...
Click to collapse
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
aabbondanza said:
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
Click to expand...
Click to collapse
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Marketplace & Non Working Tab Links
alcapone1130 said:
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Click to expand...
Click to collapse
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
aabbondanza said:
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
Click to expand...
Click to collapse
Its amazing what a couple of stripped bread ties will doo,lol.I took a bread tie and stripped the paper off of it,cut it to the length I needed and wrapped the remaining wire to one end and pushed the other end of the tie inside the pin hole,lol.It worked like a champ! MY Grab has been up and running for over a month,I just knocked on my coffee table,lol.Thank you for helping me out I really appreciated you trying everything to help me.I am so happy to have it back,now if I can just figure out why I keep seeing black boxes on my games when I play them I will really be doing fine.Thank you again.
Does anyone have any experience with removing a damaged charging port/flex cable? I made a thread about a week ago saying that mine was messed up and one of the wire strip on the charging slot was broken, but and didn't allow it to connect to my computer for file transfer. I talked to ATT and they said the store couldn't do anything and that I would need to call in. I don't want to take the risk of a huge charge, and found a single order part here www.etradesupply.com/oem-samsung-galaxy-note-sgh-i717-charging-port-flex-cable-ribbon.html
It is cheap, and I have e removed the back of my Note before, and removed most of this piece except for the ribbon, and which I have no idea how to. Are there any resources out there to help me with this? I don't want to mess up a new part trying to install this one.
(PS how do I start a new thread on the desktop site? I couldn't find anywhere to do it and SwiftKey isn't faster than using a real keyboard on my PC lol. I am obviously new)
Sent from my SAMSUNG-SGH-I717 using xda premium
Youtube is your friend. Watch the video and see the steps it takes. If you feel it's too much then try searching on your local Craigslist for a shop that may be able to fix it.
http://youtu.be/pD9R-YUT69Q
MrEous said:
Youtube is your friend. Watch the video and see the steps it takes. If you feel it's too much then try searching on your local Craigslist for a shop that may be able to fix it.
http://youtu.be/pD9R-YUT69Q
Click to expand...
Click to collapse
Thanks a lot! It totally slipped my mind to check out YouTube.
Sent from my SAMSUNG-SGH-I717 using xda premium
Bought 1 from ebay. Will try to do it myself when it's arrived.
Sent from my phablet ★★★Galaxy Note★★★
Good luck. I did it myself as well. It is not that difficult.
Sent from my MB860 using Tapatalk 2
Has anyone tried replacing just the digitizer on our phones? My friend's LCD is fine, it's just the glass that is cracked.
On my old HTC HD2 the digitizer was glued to the LCD, so swapping it out was pretty tough. I'm wondering if it's the same for this phone.
So it didn't charge also?
Sent from my SAMSUNG-SGH-I717 using XDA Premium HD app
Snarksneeze said:
Has anyone tried replacing just the digitizer on our phones? My friend's LCD is fine, it's just the glass that is cracked.
On my old HTC HD2 the digitizer was glued to the LCD, so swapping it out was pretty tough. I'm wondering if it's the same for this phone.
Click to expand...
Click to collapse
Yup, will be rough, it's glued.
Lcd and digitizer are fused on the note as well. Cheapest I seen it go for is like 250
Sent from my SAMSUNG-SGH-I717 using xda premium
gagejbond said:
Does anyone have any experience with removing a damaged charging port/flex cable? I made a thread about a week ago saying that mine was messed up and one of the wire strip on the charging slot was broken, but and didn't allow it to connect to my computer for file transfer. I talked to ATT and they said the store couldn't do anything and that I would need to call in. I don't want to take the risk of a huge charge, and found a single order part here <clipped URL because XDA won't let me quote it>
It is cheap, and I have e removed the back of my Note before, and removed most of this piece except for the ribbon, and which I have no idea how to. Are there any resources out there to help me with this? I don't want to mess up a new part trying to install this one.
(PS how do I start a new thread on the desktop site? I couldn't find anywhere to do it and SwiftKey isn't faster than using a real keyboard on my PC lol. I am obviously new)
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Did you receive the part from that supplier? Was it the correct part? I ask because I need the same part for my Note. (Samsung told me that is not a part covered under warranty)
JeremyLC said:
Did you receive the part from that supplier? Was it the correct part? I ask because I need the same part for my Note. (Samsung told me that is not a part covered under warranty)
Click to expand...
Click to collapse
Just to follow up on my own post. I ordered the part, it arrived quickly, and it was DOA Waiting to hear from customer service now.
Be careful doing this I found the new part had the wrong antenna and my reception was gone afterward. Ended up replacing my phone because of that.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I tried 3 charging ports from ebay,all from diffrent sellers and they were all DOA... Check out parts4repair, I ordered mine and 2 weeks later, my phone is fixed!
http://www.parts4repair.com/samsung-galaxy-note-i717-at-t-dock-charging-port/
I replaced mine, easy, just don't loose the screws, took about 5-10min
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
endine said:
I tried 3 charging ports from ebay,all from diffrent sellers and they were all DOA... Check out parts4repair, I ordered mine and 2 weeks later, my phone is fixed!
http://www.parts4repair.com/samsung-galaxy-note-i717-at-t-dock-charging-port/
Click to expand...
Click to collapse
its took you that long to get the replacement port?
just replaced mine as well with the ebay one from ezletroniks(or something like that). $15 shipped, arrived in less than a week from California to Wisconsin.
Took around 10 minutes to replace. Charging up fine again which makes me very happy.
So it seems apparent that this is not a singular occurrence by any means, which is a little disheartening. But I just wanted to chime in and say that I'm currently on my 3rd charge port.
Fortunately, there's an awesome place a few miles away (I would trust the tech there with my life...he's fixed everything I've thrown at him thus far) that has been able to replace the part for me each time - but every damn time, it works perfect for about 2 weeks and then it goes back to the way it was before, which is always the same symptom: phone doesn't charge (or stay connected to the PC) unless I push the phone UP from back, and simultaneously push the end of the cable DOWN. And even then, sitting perfectly still, I get a sporadic connection.
Needless to say, the 2 extra OEM batteries/chargers (that you can charge just the battery with) and ADB over WiFi have become my best friends
So I'm wondering: (a) has anyone else had this problem multiple times like I have? And (B) has anyone else experienced the same thing as far as the "manual" method I have to use to keep it charging? I'm trying to, as much as possible, rule out the possibility that there's something else wrong with it
Replaced mine
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
p51d007 said:
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
Click to expand...
Click to collapse
That's actually exactly what the repair shop told me was wrong with it...although I couldn't recall exactly until you said this. I'm pretty sure he's just re-soldered if each time, and never actually replaced the board.
So to a non-hardware person...is that problem due to faulty manufacturing/poor quality parts on the Samsung end? Or does that just end up happening to all devices with a MicroUSB connection as they get used?
p51d007 said:
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
Click to expand...
Click to collapse
I have a couple of guesses. One picture showed the connector was loose. It looks to me that the case tabs aren't soldered in. The other thing is I have one cable where the metal part sticks so far out that the plastic never touches the phone. It like sticking a screwdriver in the socket because you can wiggle the socket up and down. I now use a cable the plastic part touches the phone and doesn't wiggle the socket very easily. Wiggling any wire will eventually break it because of metal fatigue.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app