Related
How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!
hey))) as promised, the Soft-SPL and Hard-SPL
1. Soft SPL - loaded to ram temporarily, erased after reboot, use it to flash HardSPL or tested working roms.
2. Hard SPL - A version which is flashed to rom.
So, what`s this?
1. Based on oxygen spl, but
1. Doesn`t check CID
2. KeyCard security is reset
3. Allows to flash unsigned (custom) nbh files.
http://rapidshare.com/files/65732449/hspl.7z.html
Instructions:
1. Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen
2. Connect USB to pc
3. From the flasher folder run ROMUpdateUtility.exe and follow instructions to flash the Hard-SPL if needed. or you can flash *ANY* oxygen rom
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
p.s. sorry, have problems with wm6 - no info when i`ll finish it
Good Jobs :d
THANX SPV3DEV foor tool . WM6 for tis device ?
THANK YOU GREAT JOB. not tested yet. but thanks for the efforts.
how is WM6 comming as you promised?
sp3dev,
Thanks I have CID unlocked my phone.
Please I need to SIM unlock it.
how I can do it?
Please help.
Doesn't work for me.
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
You passed in boot mode? Long push camera and short power.
No...I didn't pass. Phone has white screen, when I run RomUpdateutility.exe before flashing shows me error.
Have ideo when your WM6 rom will be finish ?
Thx for the tool , great job .
wm6
HI. Please Guide coking rom for Htc S310? Thanx
quell said:
Hi,
All is OK unless I connect USB...
After run ROMUpdateUtility.exe it shows me error, that phone hasn't connection
with PC.
I use Windows Vista.
Click to expand...
Click to collapse
I've this problem too. Running windows vista aswell. Anyone found a solution?
RUU on vista
the solution is here:
http://www.modaco.com/content/Windo...U-on-Vista-It-can-be-done-the-ultimate-guide/
Hello all
my phone is fully unlocked
i soft-spl my orange c100(htc 310) and when i tried to hard-spl it just crashed wile writing the new spl
now i am stuck at tri-color boot screen
Does somebody have orange c100 romania rom?
Thanks
Maybe you will help me...
sp3dev said:
4. After flashing Hard-Spl, to avoid reflashing, use
nbhextract ruu_signed.nbh
with any official update.it will dump the nbh. you`ll see some file like 00_OS.nb0 or 04_OS.nb0, any *_OS.nb0
use Htc Rom Tool (can be found on forum) and go to build rom, select OXYGEN, use 1.0.000.0 version, and go to system box, and press "..."
Load your os.nb0 and press build rom. then you can use this nbh to flash os. just replace original nbh file within updater directory.
[/QUOTE=sp3dev]
Hello!
Maybe you Sir have an official Oxygene ROM image? Maybe you dumped it for yourself before all thos updates? I am extremally looking for it Please let me know if you could send it or upload somewhere.
Best greetings,
RA
Click to expand...
Click to collapse
Hi,
Where do I place hard spl?
When pressing this I first press camera and then open spl.ink ? Or is there another way I should do this?
i am from romania and i have spv c100.
if you could tell me how to back-up my rom i will help you.
hi SP3DEV
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
charlietruong said:
in step 1. "Copy spl.nb, spl.lnk and jumpspl.exe to the root of device, hold camera and launch spl.lnk - you`ll see the white screen" how do I do this? I copied the 3 mentioned files to root directory but how do I hold the camera and launch spl.lnk at the same time. Please explain this thoroughly. I just bought an HTC S310 and want to upgrade my toy. Thank you much
Click to expand...
Click to collapse
same problem.. any solution?
Cease & Desist!
Hard-SPL is *MY* trademark, I never said you could use it.
PSYCHE!
just kidding, but tell me sp3dev, when you disasm the SPL; are you actually rebasing the file, or just going at it by trial and error... because it shouldn't take more than 5 minutes to hack up a Hard-SPL and SSPL.
Also... really you should only call it Hard-SPL if it prevents itself from being overwritten, otherwise it's just a USPL... not that I particularly mind.
I did the HardSPL and then tried to upgrade to Crystal v5.1 but after going through the steps as I understand them to be, my 818pro just gets stuck at the Red-Green-Blue bars screen with the following 2 lines of text and it won't go anywhere else.
IPL 1.00
SPL 2.20
And then I read through and found someone posted a link to get IPL to 2.20 which I installed and now the Red-Green-Blue bars screen has the following 2 lines.
IPL 2.20
SPL 2.20
I don't know what I can do next. Does anyone have the utility to flash it back to Dopod 818pro original ROM so I may try to upgrade to Crystal v5.1 from scratch again? What solution is there there to get my phone functioning again.
Urgent. Please please help me. Thanks.
You didn't install HardSPL the right way, otherwise it should say:
SPL 2.G3.4PDA
So, just start all over again! BTW you have to run JumpSPL first before you can install HardSPL. To make things easier HMA4 created a .bat file that takes care of all the steps at once. You will find detailed instruction in the HardSPL thread and the New Upgrade Guide.
What I did was run hma4's .bat file. I don't know what went wrong but now I can't just run that .bat file to install again because I'm stuck at the RGB screen and the .bat execution just says
Code:
No device connected
Would you like to try copying again?
What can I do now? I cannot establish an Activesync connection which I think this JumpSPL thing needs...
Help...
you can download any "STEP1" connect your PDA with the bootloader screen and install it, it should be fine...if you still having issues, go ahead and download my ROM from the below link..its about 90 MB..you should have WinRar installed on your XP, download both files in one directory then right click one of them and select "Extract here" it is a shipped I mate Jamin G4 rom with Arabizer...it will replace the 3 splash screen, the Radio and reformate your PDA , BTW it does not check VID so no issue with any G4 (if you are using a G4 prophet this WILL SOLVE THE ISSUE ), when you are done...start from scratch with that BAT file.
* i assume you know how to flush roms
* This is only for G4
http://cid-61d70bae1a33dbb9.skydrive.live.com/browse.aspx/Share/PDA
havin almost d same prob too..
i think this is not d right room but if anyone can help me,
im lookin for original wm5 818pro rom but cant seem to find it.
the closest one is QTEK rom which can be found in XDA-wiki but the boot screen shows "QTEK" font in it,, but i want it to be "DOPOD"(somethin like the original boot screen)..anyone has link to this pls tell me..thanks
Thanks. I flashed it back to PDAVIET's step 1. Now re-trying HardSPL.
Get an error while trying to run the batch file. Same problem after manually copying files over to device manually and then running the following line copied from within the batch file.
Code:
D:\data\software\wm5\wm6\Update_Package\HardSPL\HardSPL G3>CeRun.exe -b CE:\JumpSPL.exe 0x10000000 \SPL.nb
cerun: failed to execute program (30123)
Help anyone?
Try this link
my solution :-
http://forum.xda-developers.com/showthread.php?t=353547
matthewchng said:
Thanks. I flashed it back to PDAVIET's step 1. Now re-trying HardSPL.
Get an error while trying to run the batch file. Same problem after manually copying files over to device manually and then running the following line copied from within the batch file.
Code:
D:\data\software \wm5\wm6\Update_Package \HardSPL\HardSPL G3>CeRun.exe -b CE:\JumpSPL.exe 0x10000000 \SPL.nb
cerun: failed to execute program (30123)
Help anyone?
Click to expand...
Click to collapse
Thank loads! That IS the solution.
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
rmorera84 said:
When i tried to install any firmware the progress stop at 11% and the Hermes only turn on in bootmode, any idea??
Click to expand...
Click to collapse
I had that problem and few more with my Hermes.
While it didn't help me, this suggestion by ultramag69 may help you...
Use the sd card method to flash a new rom, instead of a USB cable/Windows computer.
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
Hope this helps!
Just one other thing summoner, make sure you have Hard SPL V7 installed. Otherwise the ONLY rom I'd try flashing like that is the SHIPPED STOCK ROM. Its so the CID will be recognised and won't cause a brick.
rmorera84, unless you've installed Hard SPL V7 then find the SHIPPED STOCK ROM and flash that, anything else may permanently brick your Hermes.
If you have Hard SPL V7 (IPL 1.04, SPL 2.10 oli) then flash what you like...
Cheers...
- Installed latested Orange rom, that I know of - SPV_M3100_ROMUpdate_1007
- installed Hard SPL 7 & applied SIM unlock/super CID
- re-installed TNT TNT.19199_Professional_Hermes
The result is:
IPL-1.01
SPL-1.40.Olipro
I suppose I should upgrading the radio rom now!?
I am told don't try fixing what isn't broken - and it is working. 3G iNet, Phone, WiFi, BT - all good atm.
Or is there a particular update I should still install?
Thanks!
SUMM0NER, you're using an older, not so safe version of Hard SPL. The Hermes is downgraded to SPL 1.40 when you sim/CID unlock your phone. Best idea would be to re-install Hard SPL V7. Its a later version that seems less prone to problems when flashing.
Go back to the Hard SPL thread and get Hard SPL V7. I had the same thing happen to me when I unlocked the Hermes, nearly cost me my handset.
The steps are unlock Hermes, Install Hard SPL then upgrade OS.
Cheers...
Do I need to re-apply the OS rom file?
I just reinstalled Hard SPL7, now shows as IPL-104, SPL-2.10.Olipro.
Thanks!
My hermes only work whit this rom:Schaps_WM6Pro_ESN_3.54b-0808_Full
Because whit any other rom they stuck at 11%.
This is the info or the phone:
IPL-1.01
Spl-1.40.Olipro
Whit the first rom the htc boot but the phone funtion don´t work.
rmorera84, refer to my last post.
SUMM0NER, no. You have loaded the os, the reason you put Hard SPL V7 is if you want to upgrade the radio rom (not a good idea unless you are experiencing problems) or wish to change the os. Just means recovery is easier than if you didn't have it.
Cheers...
Many thanks ultramag69.
rmorera84 what branding is your Hermes (ie: Orange M3100, T-Mobile Vario 2, Vodeaphone V1605 etc...)?
Can I assume your Hermes is working right now?
If it is download and install HardSPL V.7 (attached to the bottom of the first post!)
Ones done verify that it installed correctly by holding the OK & Power button and pushing reset for a sec. The screen should display the coloured bars and say towards the centre: SPL-2.10.Olipro
It´s Cingular 8525, i could install the HardSPL V.7, now what rom i can flash??
You didn't confirm if it is working right now!?
If it is not working, try one of the official WM5 Cingular roms from this list. If that worked apply HardSPL 7 and take it from there.
Ones you downloaded the Cingular rom update you will have to keep unpacking the .exe files until you come to the actual .NBH file (WinRAR works for me).
Then follow ultramag69's instructions on flashing the rom via memory card.
Works, now i have this info:
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
I download the official Cingular WM5 rom, but. i don´t know how install this rom by memory card, could you help me??
Excellent!
Try downgrading to the Cingular rom via USB. Just double click the EXE and follow the instructions.
To use the memory card method follow these steps...
0. unpack the .exe file containing the rom with Winrar (right-click exe then choose "Extract to...\")
1. Format a 2Gb or less sd card to FAT32, copy the large 50MB-90MB .nbh file onto it and rename to hermimg.nbh
2. Insert the card into your Hermes and reset to bootloader (hold OK & POWER and push RESET for a sec with the stylus)
3. If you haven't stuffed up the other steps, follow the prompts.
The reason to use the memory card to upgrade a rom, rather than a usb cable, is to cut down on failed upgrades (dodgy Windows/usb port/usb cable/etc..).
All working? Try upgrading to a Hermes rom that didn't work previously.
Any rom you can find in the Hermes section. Go to the WM06 part of the forum, theres a sticky at the top with about 50 older roms and you'll find other roms there too (latest is wm6.5).
Cheers...
i install the official WM5 AT-T version the WM6 AT-T, but, i still whit the no-gsm problem, can i flash i radio? or what i can do??
You may not be able to fix this, if you know what the original SHIPPED STOCK ROM was and can find it, then flash that. It may not work, if it gets stuck at 11% - 17% mark it means the radio ROM is stuffed and the memory area is corrupted. Not fixable.
You could also try, if you know what it is, the original radio rom by itself. Again, if you can't get it to work, you have a PDA but won't work as a phone ever again. Sorry to be the bearer of bad news.
Im to having the same problem, it keeps going back to the 2.1.Olipro boot loader.
I tried the memory card option and it starts to install but then stops.
Does anyone have and sugestions?
Cheers
Help Help
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
So, after first succesefull flash of my tytn I took friends mda vario 2 to do the same. And bricked it!!!
Because of first unsuccesefull flash when I downloaded RUU_inside.nbh file into HardSPL7 directory. So, I connected vario and started RUU_wrapper. BUT in a next few seconds I realised that I am upgrading ROM instead of HARDSPL-ing File inside was from DopodAsia WWE.
Upgrade stared, in a 30minutes it stucked in 24% and I disoconnected PDA. After that it stucked in bootloader! SPL 2.03!
I tried to do HardSPL after-no help. I tried to install ATT Stripped ROM- error on 1%. I downloaded official WM 5.0 GER - no help again.
Few more attempts of flashing HARDSPL, and ROM-s via RUU-wrapper didnt help eather. THEN JUST SOFTRESET: I saw dopod bootsplash screen, and windows started normally!!! I couldnt believe, because I was prepparing to do that complicated procedure of unbricking.
After starting windows I just did HARDSPL and ATT stripped ROM: All OK UNLESS GSM!
Is it possible to fix??
To +Que PPC and boog321: thanks to earlier advices!
OK! I flashed RADIO ROM 1.56.70- IT WORKS!
Guys who are making this software are fenomennal
hahaha!!!!! Nice experince man!!!
Well i think we all has to thank to Olipro! POF! and many old XDA members that makes this posible!!!
Keep it up.... and for the enxt device please... read eveything two or three times! hahaha and please don overwrite files... its better to make new folders!
Keep it up!
haha, thanks Que...
I was in a hurry, so I just connected PDA and start wrapper. I shocked when a I saw wrong .nbh file, but it was too late. But luckely it looks like new ROM was partly OK and I was able to start WM, then flash HardSPL and WM correctly.
Both hermes are working fine.
P.S. I would like someone to put simple guide for people who only want to change their ROM to simple WWE, and have some experience.
1. Download HardSPL7 and unzip to folder on PC
2. Download ATT ROM and unzip to different folder on PC
3. Connect via ActiveSync
4. Start RUU wrapper from HardSPL folder and follow instructions
5. See if you flashed correctely (in a bootloader must be 2.10.01olipro in SPL)
6. If its OK than reset, start WM on PC, connect via ASync and start RUU-wrapper FROM ATT ROM folder, choose autodetect or SPL you have seen in bootloader screen - accept everything....Wait for 10min and enjoy in ENG ROM!
Thanks Oli, Pof and all others of course!