I've read http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK
and http://wiki.xda-developers.com/index.php?pagename=DeadBoot
My problem is, I'm not sure if I've bricked my phone or not.
I tried to flash a rom from my SD card on recieved a "no file found on disk" error (or something close to that). I hit reset, and now nothing happens with I turn on or reset my device.
It seems the charge light went from red to green, so at some level its working.
If I leave the power cable plugged in, the light stays red (and eventually goes green, I assume when changed). If I take the battery out with the power still plugged in, the light flickers red/green/red/green then goes blank.
If I leave the power cable plugged in, and remove the battery and then wait a few mins, all the lights momentarily flash.
I'm just not sure how to get back to the bootloader? I've read to try putting the battery back in while holding down the 2 soft keys, but thats not working.
I remember on the 6828 that I had to press reset and on while holding the soft keys to reboot?
I'm really struggling here.
Is it the soft keys? Is it the action key and reset?
(I WAS using a cooked ATOM rom on my 6828)
Please? Any suggestions? I'm really not up to building a cable!
UPDATE: Ok.. I've recovered. Short version: take out SD card and battery. Hold down reset button AND the 2 soft keys WHILE putting the battery in (this take some co-ordination). Wait a few seconds (up to 20) and should come back.
wallaceff said:
I've read http://wiki.xda-developers.com/index.php?pagename=ATOM_BRICK
and http://wiki.xda-developers.com/index.php?pagename=DeadBoot
My problem is, I'm not sure if I've bricked my phone or not.
I tried to flash a rom from my SD card on recieved a "no file found on disk" error (or something close to that). I hit reset, and now nothing happens with I turn on or reset my device.
It seems the charge light went from red to green, so at some level its working.
If I leave the power cable plugged in, the light stays red (and eventually goes green, I assume when changed). If I take the battery out with the power still plugged in, the light flickers red/green/red/green then goes blank.
If I leave the power cable plugged in, and remove the battery and then wait a few mins, all the lights momentarily flash.
I'm just not sure how to get back to the bootloader? I've read to try putting the battery back in while holding down the 2 soft keys, but thats not working.
I remember on the 6828 that I had to press reset and on while holding the soft keys to reboot?
I'm really struggling here.
Is it the soft keys? Is it the action key and reset?
(I WAS using a cooked ATOM rom on my 6828)
Please? Any suggestions? I'm really not up to building a cable!
UPDATE: Ok.. I've recovered. Short version: take out SD card and battery. Hold down reset button AND the 2 soft keys WHILE putting the battery in (this take some co-ordination). Wait a few seconds (up to 20) and should come back.
Click to expand...
Click to collapse
dude its a known trick.....hahha u a newbee fer all dis stuffs....
nice tips bro
Related
so my story goes as this. just flashing my tytn (x01ht) with a custom built rom from the kitchen, ran ruu as normal and when iit begins at 0% it fails and suggests to me how to correct the mistake by pulling the battery out. so i do that and put it back in afterwards. now it wont even power up. lookup in the wiki to try and jump start it by pluging in the usb power cable, led goes red and put in the battery and led goes black not the yellow that means charging. so now i freak out. try this several times hoping that it will go yellow but nothing.
so i think i have a nice looking expensive brick that i could just pawn for parts or is there still hope left in it. i had flashed it about 10 times before this ever happened.
anyone there to put me out of my misery or can it be revived from the dead
much thanks for any response
Hi, I can just tell you what helped me in a similar situation: Take the battery out, put the charging plug in, (is the light on red than?), put the battery in again. Now press power button, commmanager button and soft reset at once - this is when my came back to tricolor screen. Before that I put a rom file that I renamed to herming.nbh on the empty SD card - I'm not sure if this is necessary, since it didn't start to install the rom from the SD. I hope this may help you.
thanks for the response.
thats what i have been trying to do. on a working one it will bring up ktl mode or the led goes yellow for charging but on my brick it doesnt do anything at all, not even the bootloader comes up.
Hi all,
I need an advice from you guys please:
My Topaz is not turning on, it simply does not do anything.
Last time I wanted to change the language but my battery was not fully charged, so in the process it suddenly turned off and since that time I am not able to turn it on, does not display nothing on screen when I press the on button it just vibrates continuously and not stop, and that´s it...
The charging light was on the 1st time I tried, but not the second time.
It is SIM unlocked but not hardspl´ed
Any advice would be great!
Thanks in advance
UPDATE 13-Mar-10
Today, I connected Topaz to wall charger, amber led turned for about 10 sec, then turns of, then vibrates, then nothing again.
I tried to do hard reset, nothing happened, then after some minutes the device is short vibrating every 1 min aprox, no led on, still can´t do nothing more.
EDIT: After 15 min of short vibrating every 1 min, now it´s completely dead again........
Thanks for reading,
Can you put it in bootloader? Is a hardreset possible?
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
yes, Vol down and powerbutton. should boot to serial/usb flash screen.
Thanks guys for your reply
Soon as I get home I´ll try and report back
Cheers,
Flash a stock ROM
jmkhenka said:
Try to turn the phone off, remove battery, and insert it again. Then hold vol down and press power. Do you get red/green/blue (or whatever) colors?
If you do. let it boot until it says USB (perhaps need to connect usb to PC for it to change from serial to usb) and after that just run the topaz ruu and it should flash.
If you dont get it to start to 3 color screen try and hold up+down and press power.
Click to expand...
Click to collapse
Hi
Just check that if you try to reflash the ROM whether you should use a stock ROM vs modified ROM as you wrote that you do not have HardSPL on your Topaz.
Once you have successfully reflashed using stock ROM do a hard reset and then install HardSPL 1.83.
Good luck
Aussie
Still need help!!
Ok guys,
Let me explain you what happened:
None of the instructions above worked...
Can´t put on bootloader, hard reset nothing happens
When connected to wall charger amber led is on, if I press power button led turns off and vibrates, then led turns on again but nothing else happens.
Pressed down vol and power = Nothing happens
Pressed up/down vol and power = nothing happens
EDIT: Connected to PC and automatuically installed a qualcomm driver not detected also by WMDC
Disconnected from PC then connected again to wall charger and now amber led not turns on....
Please help!!
Any other advice please!
I really don´t know what else to do
Thanks in advance for taking your time on this thread
Per your PM, I'll certainly help you if I can.
Do you happen to know what caused it to brick? This will help determine how to bring it back. Did you attempt to flash a custom ROM w/o HSPL?
I am not an expert on this but have seen some chefs claim they can bring back a bricked device.
There is a program called MTTY that can usually get your phone to connect to your PC and there are functions to run in that program that can get it to a flashable state so you can reflash your shipped ROM.
Also search the Wiki for restoring bricked device, regardless of the model, it should be the same process. I think I have seen this in the Tilt(Kaiser) forum and maybe in the Fuze (Raphael) forum.
I haven't used this program in a while so I forget the commands but you should be able to find them in a search.
In the meantime I'll do a little research too and see what I can find out.
The main thing we need to accomplish is getting you back into bootloader mode.
1. Here is a link for recovering a Hermes and it has info on mtty.
Thanks a lot Bruce,
I have the original ROM and my Topaz is the unbranded model.
I was just trying to change language but battery was too low, then it turned of and you know the rest of the story.
I have it SIM unlocked but not hardspl´ed and I was not doing any ROM upgrade or so...
I´ll try to use MTTY and find about your recommendations, later report back.
I appreciate a lot your reply!
Cheers,
EDIT: Tested MTTY but in some point says "power on the unit " but that is what I can´t do, nothing happens
Will continue testing and searching...
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Bruce Inman said:
This is from the Wiki. It may help. Says to use PUTTY instead of MTTY... with instructions.
Another thread on recovering device.
Click to expand...
Click to collapse
Thanks Bruce,
I went through both links but nothing...
The main prob is that I can´t even make it turn on...
Now when wall charger is plugged I do not have the charging led on, so I am really lost...
I do not have another battery to test but I don´t think is that because Topaz is almost new!
But Now I think it´s not charging the battery...
Hope any other idea can save me
If it is almost new try to send it to warranty!if it has the original hspl no prob then!is better then trying to reapair youself, with the cost of loosing warranty!
Good luck with that!!!
Thanks, but I do not have that option
I have high hopes with all the great team of XDA!
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
komsa said:
first thing first,you have to have power in your phone.....borrow the battery from someone or recharge your battery in somebody else's phone.......then try to go in to bootloader mode (volume button down and power button)..........
Click to expand...
Click to collapse
Yep!
I ordered today another battery
Soon as I get it will report back.
Thanks,
Maybe this will help
It happened to me once. Nothing seemed to work. What did work, I left the phone charging for a day. First take ou the battery for at least a minute. Put it back on. Then connect the wall charger to the phone and let it charge. Hope this will help.
When it happened to me the LED wasn't working either, just connect the charger and let it charge.
Thanks,
I done that yesterday and left it all night but nothing...
I really hope is a battery problem, I´ll find out soon as I receive my new one
wrong place
Exactly samething happened to me.. the only difference was that I was using google maps and connected to my car charger. It somehow didn't charge and ran out of power and kept restarting whenever I tried to charge from a wall-socket.
This is what i did... worked for me.
Take out the battery from the back
Hold down the power button for at least 30 seconds to drain out the static charge.
Take out the sim
Plug in the USB to the phone (without the battery and without the sim)
With the phone connected, press the Red button at the back (soft reset)
Unplug the phone from the charger
Put the battery back in
Connect the USB to charge
Cross your fingers and say a lil prayer
Wait for 30 minutes
Turn it back on.
Lemme know how that goes 4 u
Thanks
I done all your procedure but after this point: [*]Connect the USB to charge
Led charging light did not turned on...
By now my only chance is to test with a new battery (which I will receive on thursday), but I do not have too many hopes as the device is almost new
I´ll report back on friday.
Thanks to all and I will be happy to receive any other suggestion
Need some advice please
Any Flyer member who can advice me please?
Buyed a WIFI Flyer 16Gb Gingerbread stock no rooted turned on and suddenly turned off and got stuck in black screen (with some light in the back) vol down + power, nothing.
battery has 100% charge, but red led turned on and off ocasionally.
Any advice how to revive it would be greatly apreciated!
Thanks in advance,
Soft reset - Hold down power button only. Keep holding until tablet resets. You should know when this happens. You can't bring it up in bootloader/recovery (down vol. + power), until it's first actually turned off.
Does your PC recognize a device being plugged in when you connect
Sent from my HTC Flyer P510e using xda premium
.
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests.
Just behind power button a green mini led is turned on now all the time, probs started when removed back to insert sd card.
Tooked off to make some tests but now still nothing...
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
orb3000 said:
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests... probs started when removed back to insert sd card.
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
Click to expand...
Click to collapse
Take off back cover... Remove SD card... Try to reset again, power btn only, hold down 20 to 30 secs., don't use volume btn.
Nothing happens
i would suggest trying to globatron's attention. if anyone on this board would know what to do it would likely be him
orb3000 said:
Nothing happens
Click to expand...
Click to collapse
I would agree with mcord11758... Still...
orb3000 said:
battery has 100% charge, but red led turned on and off occasionally.
Click to expand...
Click to collapse
A red led isn't going to show with a 100% power condition. Later you wrote...
orb3000 said:
It didn't work pressing only vol down for a while, or pressing only power button, it never rests. Just behind power button a green mini led is turned on now all the time...
Click to expand...
Click to collapse
(doesn't make sense to me) A green led can't show unless the tablet is plugged into a power source and the battery actually is 100%...
If yours is a stock unit with a stock rom (and isn't defective), I would suspect a low battery condition that can't reset/reboot for lack of power...
Suggest you plug it into the wall and try the reset procedure again, and if still a failure, (maybe you can get some help from globatron or) call HTC.
...and then again, as I've read in other threads (that you've also seen), maybe all that's needed is a battery disconnect & reconnect. - Hope you get those pics, and if so... make it a last course of action, as you'll have no warranty if you do it.
Thanks.
Update:
I left computer connected to Flyer all night, and the day after it was turned off, then unplugged from PC and plugged it again, PC recognized the tablet and after that I ran the stock RUU, now it´s stuck on the process as it has been more than 20 minutes and progress bar in computer is at 100% with the following legend:
sending..........
updating the Rom image on your android phone
It is stuck there, how much should I wait? or if you recommend to do something else?
Thanks in advance for all your help.
UPDATE: RUU failed, says I have the wrong image, finished, exited and rebooted normally!
Now working, but I´m afraid to open the cover to insert my sd as the last time it was when it was turned off
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
globatron said:
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Click to expand...
Click to collapse
orb3000 said:
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
Click to expand...
Click to collapse
That's weird, if it's not too much could you try and get a logcat (adb logcat) when its screen goes off while opening the cover. That should help us establish whether this is a HW problem(unique perhaps bad mainboard) or software problem (me,globatron,Lee, etc. experienced)
I can also confirm that it happened to me too couple of months back, but after soft reset it rebooted fine, but the backcover issue is new.
Sent from my HTC Flyer P510e using XDA Premium HD app
hello
Im orbs friend, my htc flyer still having the prob, everytime i touch the cover or pusih it by accident it goes back.
What I do is leaving it charging for awhile and press power button and vol down at the same time for around 30 sec for a couple of times and then it re start. Im guessing its not a software problem i dont find an explanation i even updated it to 2.3.4.
Need some serious assistance. Was playing with my dogs just a bit ago and decided to record it. So I go to the camera and switch to camcorder and the screen just turns green and the flash comes on and basically it's stuck. Ok so I go to settings and force stop the camera. Try to start it up and it just says unable to start camera. Ok so I guess I'll just restart the phone. Go to restart get to the white htc screen and the flash is still on. hangs there for quite awhile so I start hitting buttons. Screen goes black so I hold the power button again. Capacitative lights just flash. So now the phone won't power on no matter what I do the capacitive lights just flash at me. Any suggestions?
try holding power for like twenty seconds to reboot it.. it's like pulling the battery out. The capacitive light flash apparently means it's signaling to you that it's about to do a full reset.
Sent from my Nexus 7 using Tapatalk 2
jayochs said:
try holding power for like twenty seconds to reboot it.. it's like pulling the battery out. The capacitive light flash apparently means it's signaling to you that it's about to do a full reset.
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
Will give it a shot. My first phone with non removable battery.
Seems to have worked thanks a ton. Kinda worries me that the camcorder freaked it out like that though.
broons said:
Need some serious assistance. Was playing with my dogs just a bit ago and decided to record it. So I go to the camera and switch to camcorder and the screen just turns green and the flash comes on and basically it's stuck. Ok so I go to settings and force stop the camera. Try to start it up and it just says unable to start camera. Ok so I guess I'll just restart the phone. Go to restart get to the white htc screen and the flash is still on. hangs there for quite awhile so I start hitting buttons. Screen goes black so I hold the power button again. Capacitative lights just flash. So now the phone won't power on no matter what I do the capacitive lights just flash at me. Any suggestions?
Click to expand...
Click to collapse
Sorry to hear this, try this. Plug in the charger, hold the power button. Release power button, hold it down again all with the charger in. I had some sort of soft brick messing with custom roms. It would not power on till i tried with the charger plug connected. I was spooked and thought it bricked.
Let me know how you get on. If that fails, RMA time
Hendrickson said:
Sorry to hear this, try this. Plug in the charger, hold the power button. Release power button, hold it down again all with the charger in. I had some sort of soft brick messing with custom roms. It would not power on till i tried with the charger plug connected. I was spooked and thought it bricked.
Let me know how you get on. If that fails, RMA time
Click to expand...
Click to collapse
jayochs advice fixed it. Kinda freaked me out. May return it anyway as this isn't the first time the camera has caused some goofiness with the phone. Not rooted still 100% stock.
So I've gotten the hard reset bug, and I'm working on fixing it up myself. (RM-821 Telstra AU)
I've got nokia care suite all setup and ready to go, but the phone WON'T FLASH.
When it comes up asking me to hold down the buttons etc etc etc I hold power and volume down, press the retry button, wait for the vibration, take my fingers off power and volume down and put my finger on volume up.
By my phone just goes back into the lightning bolt/gear mode thing.
One thing I've noticed is that after the vibration my computer does the dundundun USB connection sound that usually means the USB device inserted isn't understood, instead of the dunDUN one that usually means success. (weird explanation but I think it works)
Thanks for any help, guys. I really need to get this thing going again.
Edit:
One extra piece of information would be that if I try to let it boot normally now, it shows the unsufficient battery icon after the carrier symbol. If I leave it there while chargin though, it eventually goes as far as the black NOKIA screen and won't charge.