I have installed this GPS rom, then decided to reinstall WM6 from HTC site. Now I cant sync with my Vista WMC. I tried re-installing the WM6 fresh install and bootloader says there is an error. It starts to load in the RBG screen says 1% then says error not connected. Everything is connected right. Currently my pc sees the P4000 I cant edit extract or copy files to the unit. WMC says error. My Ipaq syncs no problem. I dont know what to do. The HTC techs dont know either. Is there a way I can flash the rom first then install WM6? Is this a hard problem?
relock, and install stock pre-gps rom.
Sounds like an incompatible boot loader. What does it say when you load up the RGB screen? Like the guy before me said you will likely have to re-lock and re-flash.
Qsn tho, Why the heck would you want to go back to stock?
nation888, return after you have stated that you have read and followed these FAQs, troubleshooting, guides, and instructions:
Titan Wiki
...particular the steps in the Returning to Stock page.
Related
I have a tmobile g4 wizard.
when I tried flashing it either:
a. gives me a old utility error
then i get the newer italian 2.5.2 utility to flash with.
b. no matter what rom i use (I tried molski's 3.3 and crossbow reloaded 1.7 = both are without ipl/spl)
the utility seems to update, and then gives me an error at 99%. it doesnt crash, it gives an error
then i have to flash it back to tmobile or wizard love to get this working.
any idea guys ?
yeah, put your device into bootloader mode before you start the RUU.
doesnt help.
again meter progresses to 99% where it turns red and then the application on the pc gives me an error.
firewalls / antivirus are turned off too.
Hello i had the same problem while updating to wm6 my qtek 9100, here is the solution: downnoad the Wizard_Love rom, t is already patched so it works on your g4, Read g4.3 Here http://forum.xda-developers.com/showthread.php?t=310831&highlight=Wizard_Love
First off have you CIDunlocked your device before you flashed?
I was having the same problem with my phone yesterday. I thought i actually bricked it when trying to flash it. Eventually i had to use the rom from the htc website and then use ShellTool from the sticky in this forum. Finally i got wm6 loaded with its help.
Good luck!
I was trying to upgrade to radio v1.43 in the hope that battery life was improved over 1.41 however when it got to 8% it stopped and gave me an error i can't remember After atempting to recover, it got off the three colour screen now the 3100 stalls on the blackshadow version4 screen (bootloader screen?) and goes no further. I tried reflashing but got a 260 and using mtty, only getting 2 com port options, didn't offer any help.
I'm really sorry to have not been able to sort this with reading through the relevant post but I haven't found a solution. What else can I try?
Hi,
Could you pls advise what is your device made, model, SPL version ... etc.
Also did you try to do Hard reset?
I'm using now black MAJIK (and few days ago black shadow) with radio 1.43 with no problem.
its the SPV m3100 When I decided to go Black shadow I read up on mr vanx and made sure I had all the things I needed. If I remember right, when I came to upgrade to Majik the auto detect found the second option down
SPL-1.04/1.10 - 1.09 Bootloader. I've realized since I had a spaz and ran the RUU from the archive this time. From what I've since read thats not too cleaver.
I have tried a hard reset and took the battery out instead of pressing space.
I dont know if this information on the starter screen is of use
M 05
S 04
B 05 D 3lak
I'm not sure, but hard reset doesnt mean you take the batery out.
Please check that link:
http://wiki.xda-developers.com/index.php?pagename=Hermes_For_Beginners#hardreset
I was in your position (hanged on booting) few days ago, and when i did hard reset, it changes every thing to basic normal condition.
i meant when i did a hard reset when it asked me to press space to reboot I took the battery out. I tried again this time pressing space to reboot but I still get stuck on the loading screen. I can't connect by USB to the PC I'm guessing the drivers on the phone haven't loaded and I'm stuck as to what to do.
Does anyone have any ideas?
try look at it http://forum.xda-developers.com/showthread.php?t=286755
ok I've tried everything I can think of to connect the 3100 to the computer so I can reflash it but mtty gives only com 1 and com2 but no USB and neither those two work, active sync wont connect so I disabled it as suggested and running the radio ruu and wrapper wont querry the device. I am now at a loss as to what to do next someone must know what I should do. Please?
what is your SPL?
try this http://wiki.xda-developers.com/index.php?pagename=HTC_Hermes
sl is 1.09 i'd updated it on the previously successful black shadow flash
msn [email protected]
icq 150277111
AIM TazmanFH9
Yahoo bigfathairyboggart
I have tried changing KITL trasport but I am unable to select or chose either option. I have also tried the rversion command in the tri colour screen but nothing happens. I hope I'm missing something nice and simple but I get the feeling I'm not going to be that lucky. Please help
tcSPVm3100 said:
sl is 1.09 i'd updated it on the previously successful black shadow flash
Click to expand...
Click to collapse
I suggest you check again, press and hold the side OK button and the power button...then put the stylus into the hole in the bottom of the unit.
yeah I've done that it's "SPL-1.09"
I had this exact problem yesterday, with the same bootloader too. The phone would not pass the splash and IT refused to upgrade. I ended up downgrading to a shipped wm5 rom (in my case the cingular 1.30.502.1_1.11.00.00) which to my surprise actually worked as no rom radio or spl upgrade moved at al on my phone. Then upgraded back to black majik. I hope this helps.
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
tcSPVm3100 said:
Thanks. I downloaded the trial of wm5 from the windows website and it asked me to install .NET framework version 1 so I got that but it turns out to be 2.0 not 1.1 It would say it had repaired but it would say this with or without the phone connected.
Click to expand...
Click to collapse
Just download a WM5 ROM from the wiki page!
ok tried this too no luck.
Trying to use the one from orange (linked to through wikki) I get an 294 invalid vendor error however active sync cannot connect yet of course so is this to be expected?
I have however gotten a connection with mtty which is a step forward dunno what to do with it yet though except trying the password 0000000000000000 command but it not disabling the password. This then lead me to read for a further hour how to change it and I've got to be honest; it beat me. I have No idea what the hell its talking about. My head hurt with so much reading.
I get a no gsm pop up v briefly on loader. I so want my phone back
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
tcSPVm3100 said:
I have since tried CID unlocker just so i get something installed onto this brick but I either get a connection error or it telling me it can't install for some other reason. I can not set the password in mtty to 0000000000000000 so how do I do that and is this the first step to getting things sorted? "just running a rom install" is not happening I can get a USB connection in mtty and that is it. Is the fact i'm running SPL 1.09 a problem? I'm getting precious little help guys If i'm posting in the wrong place or something please let me know. I need thing thing back now. Hours are drifting by with me trying to get some head knowledge but I still need some guidance please
Click to expand...
Click to collapse
can u flashing HARD V7?,i think better u have IPL 1.04 SPL 2.10olipro first ,then try to flashing radio?
and did u try SD card.
In bootloader can anyone here connect with active sync? I can't so updating rom and radio flashes in the usual way isn't possible. Trying the hard spl again it tells me to make sure active sync is connected and as it isn't it throws back a 262 update error. 0% on the hermes and that's currently as far as I can get. I have no means with which to access the memory card.
The reason you get an invalid vendor ID is because your CID doesnt match....download a ROM which is for your device (an orange one?)...then try.
You need to read the wiki alot more before trying anything else since you are not aware of the vendor ID error...nor the fact you MUST use HardSPL.
I linked to the orange ROM from wikki and tried installing it. it was while installing THIS ROM SPV_M3100_ROMUpdate_0407.exe I got invalid vendor error.
Installing a recent DL on HARD spl v7 I get a 240 open file error that's one I haven't had before.
With all other attempts they all say they want an active sync connection.
I can not connect to the phone through active sync
so all attempts by me to flash anything to the phone using an RUU fails.
Hi Folks,
I'm stuck in the tri-color screen for bootloader 1.06.
I have DCD 3.2.0 w/3.42.02 radio on the XV6800 and was trying to upgrade to radio 3.42.30. My system is Vista 32-bit.
I ran the Titan Relocker and it put SPL-1.06.0000 back onto the device and was planning on then putting 1.2 onto it.
Running titan_exitbl.exe says "Cannot open USB port. Please make sure, that USB connection in ActiveSync is disabled."
Unfortunately it is now stuck and even after ending the Sync Center service I can't get titan_exitbl.exe to pull it out of the Boot Loader.
Ideas? Thank you!
I could fire up an old XP laptop and try it from there.
Loaded ActiveSync 4.5 on an XP laptop, disabled USB connections, ran titan-exebl.exe and the device is booting now.
I'll continue on and see what else I can screw up.
Loaded SPL 1.20
Loaded 3.42.30
Loaded SPL 2.40
Device is back to working! Off to see if GPS is back after being lost with 3.42.02.
titan-exebl.exe
Where can I find titan-exebl.exe? Google doesn't turn up any results other than here?
titan_exitbl.exe
Never mind... just located it on my own hard drive!
Cheers!
Stuck on Bootloader
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Try changing your spl back to 2.40.
Throwing it back into the tri color screen again and flash the sprint stock 3.35
But put it on the root of a fat32 formatted micro sd card in the flavor of under 2gb.
Just run the exe from your computer it will extract the files from the exe to some location on your computer, normally the ruu update folder.
There will be a ruu_sighned.nbh file locate it and copy it to the fat32 formatted card rename it TITAIMG.nbh
Let the phone boot into the bootloader and it should detect the file on the sd and update the rom for you, by stating loading ......
Then will prompt you to update press power key.
Sense you are not on sprint don't let the first time custimizations run ... pull battery once you get to your mobile today screen on first boot...
Use active sync or the sd method to update your rom to whatever you wanted originally.
Most full updates from carriers the ones that flash both the radio and rom will run regardless of the boot loader thats on the device.
Happy flashing
Just thought I'd toss in here that GPS does work, but I have to use GPS Viewer to get a lock on the satellites first.
softwind said:
OK... I've tried titan_exitbl.exe, and it still doesn't work.
Here's my problem in chronological order:
1. I've been having a few problems (bugs) in my current custom ROM (PPC Kitchen 3.49 version), so I decided to re-flash to a stock ROM, see if the problems were fixed, and then try to flash back to a custom ROM.
2. I tried flashing to the Sprint 3.35 ROM. The RUU showed the progress bar on both my PC and the phone. But at 0%, I got a message saying "an error has occured" - or something to that effect.
3. I decided that the error was because I was running a custom ROM, and Sprint didn't like that. So I ran the Titan Relocker utility, thinking this would cure the problem.
4. I followed the steps on the screen and then got a message saying the relocker utility had completed successfully. The phone rebooted and went into the tri-color bootloader mode.
5. I retried the Sprint 3.35 ROM update, but got the same connection error, and the progress slider would never move from 0%.
6. I decided the phone had locked up and performed a reset with the stylus. The phone rebooted and went back into bootloader mode. The screen shows "TITA100 SPL-1.06.0000"
7. And that's as far as I've gotten. I've tried several hard resets using the buttons and the stylus together. I've tried removing the battery and reinstalliong... but the phone just goes back into bootloader mode.
I've tried both titan_exitbl.exe and UNI_Exitbootloader.exe, and neither utility seems to help. I get a message saying that "All data was sent... the phone will reboot now... please check your screen". The phone's screen blinks for a moment, and then returns to bootloader. Nothing can get it anywhere else.
I've tried different USB cables and ports. Activesync won't detect it, but the utility update software does.
When I run the Sprint 3.35 ROM update utility, I get an error at 11% saying "invalid vendor ID" and the update refuses to run. I tried to run the Titan Re-locker utility again, but it requires an ActiveSync connection. I've tried both enabling and disabling the USB connection in ActiveSync, but that seems to make no difference. The utility simply says no USB connection is available. The ROM update utilities will detect the device via USB - they just refuse to work with them.
I also tried running a DCD Tital 2.1.0 Bell ROM. The progress slider freezes at 0%, and then I get a message saying the RUU has encountered communication errors during the update. I've been through the recovery process the utiity suggests about a dozen times... it sill returns the phone to the bootloader screen.
So I'm getting pretty frustrated... does anyone have any ideas?
Click to expand...
Click to collapse
please i have this problem how to fix this?
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
drewcam888 said:
Please state your exact problem and what you did to cause it. Including all versions of rom and radio and bootloader.
Click to expand...
Click to collapse
Thanks!!! Ok, i cant remember eactly what is the v radio but i think 3.35 or 3.42 i cant remember exactly it's one of these. the SPL 1.06 Locked i cant unlocked i cant use titan_exitbl.... the SD update doesnt work stuck on loading.., i cant update from pc stuck 0% then Recovery Error help me. I My phone is bricked? Sorry for my english....
Did you try to install 2.4 unlocker?
drewcam888 said:
Did you try to install 2.4 unlocker?
Click to expand...
Click to collapse
Yes, i try from SD and nothing stuck on loading... from windows with RUU nothing 0% stuck and then UPDATE ERROR[262] now i don't know to do
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
drewcam888 said:
2.4 doesnt use sd and it is run from a .exe. Make sure you aren't trying 2.47. Are you sure you tried this?
Click to expand...
Click to collapse
Ok, but how run from windows? If i cant connect via activesyncs the phone is on SPL mode i cant out of that and the msdos windows say "No device conected" when press enter from windows i cant unlock. Any idea? I'll try 2.47 but how run from windows with the phone en SPL Mode?
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
drewcam888 said:
Please read. I said run 2.4 not 2.47. Put the phone in bootloader and it should say usb at the bottom. Then run 2.4 .exe unlocker. I think it should run without using activesync. And by spl mode do you mean the phone is in the bootloader.
Click to expand...
Click to collapse
Look i cant run Hard-SPL-MFG (Olipro 2.40 Unlocker) because when i run the Bat Or MSDOS Windows say "No device connect" question me if i want retray copy the file.
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
drewcam888 said:
Ok so i guess it needs activesync. About your only option is to install a pregps rom so the phone will boot and then you can reflash the custom rom. Below is a pregps Verizon rom and radio that will work for 1.06 bootloader. Called rom 2.09.
http://forum.ppcgeeks.com/showpost.php?p=834294&postcount=4
Click to expand...
Click to collapse
No luck, method A SD Card Loading.. then cheking... then show a number corner 00028002 and say down Not allowed.
Method B, via PC and RUU then ERROR INVALID VENDOR ID.
Any idea? Thanks bro.
I think my phone is bricked... noway load the rom... i've tried load bootloader unlocked via SD last option and nothing!! damn this is so
I screwed up my ATT8525, by trying to upgrade it. Here is what I did in sequence:
1. I used HTC_Hermes_SIM_CID_Unlock_v3a, and I first unlocked the phone, it was pretty straight forward.
2. I installed HTC version of ROM HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108 .. It worked fine except for sound . Because of sound I decided to go to back to a lower version WM5.
3. I installed HERMIMG_Qtek_WWE_1.18.255.3_Ship.nbh, using a RUUWrapper.
So now the phone gets stuck booting in Windows Logo screen. Is there any way to flush the ROM without Active Sync? Does anyone know of any other option of flashing ROM?
All info is here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeForBeginners
1st thing, Whats your SPL? If you don't have Hard SPL installed you need a boot up the bum...
Untick "Allow USB Connection" in the Activesync settings on the PC. Go to bootloader, connect via usb and run the HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108 ROM RUU_Wrapper.exe again... This should get you a bootable version of windows as it worked before.
INSTALL Hard SPL if you don't have it (I believe it will only be 1.10 as you've unlocked your phone) - your SPL should be 2.10 oli...
Then if you need to, you can use the sd card to flash anything.
You may have "unlocked" your Hermes but you may not have superCID it meaning that even though you can use other sim cards you can't install other ROMs for different carriers... Hard SPL fixes this.
i'm sorry.... i still don't understand...
hi, ppl, i successfully FLASH HARDSPL my tmous hd2, but after that when i try to flash a new rom, i keep getting this error code 262. does any one know how to fix it? when install new rom, it keeps stuck on the page where both the computer and the phone come up with this bar but stay at 0%. endup the programe show me how to recover the phone....
good thing about it is that even i failed the update, nothing change, phone still work as always,
can someone help?
i was trying to install L26LEO2.1 gold edition
a corrupt ROM image, maybe? try downloading it again or go for another version
boot to bootloader, what does it say next to spl?
loads of eople run hspl and think theyve installed it, but actually they chose x.xx.0000 in the list, which IS NOT hspl.
run hspl again, and this time choose 2.08.hspl.