My phone model is x01ht, currently I am using WM6.0, and I want to update to WM6.1, so I use Hard-SPL-V7 and follow the instructions to update.
However, when I was at the below step, the image Ver. was 1.00.000.0 instead of Hard-SPL-2.10, and the instructor didn't say anything about the situation I have at this moment. Below picture is my case:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and the following one is the correct case:
How can I change the Image Ver. into the correct one? Please Help, and thanks in advance.
That is the same screen I got also, but I went ahead and flashed anyway (I like living on the edge! ) It did update to hard spl, so you should be okay.
Really? Since I was afraid my PPC would become a brick, I just can do nothing with this case. Thanks a lot!
Hard SPL doesn't update
I have image version 3.54.263.2
And when i try to update to hard-spl 2.10 it seems like it doesn't copy the image to the device ( Hermes 200 ).
It says the update is complete but when i check the device again it hasn't updated at all.
wm 6.0
Rom : 3.54.263.2
Rom date 07/09/07
radio : 1.47.00.10
ext rom : Rom : 3.54.263.102
anyone have a clue?
You're looking at the rom version, NOT the SPL. You need to go to bootloader to check your SPL - hold ok button above flywheel, power button and reset with stylus, hold all three in until you get to the tri-colour screen (AKA bootloader). You should then see your IPL and SPL. reset normally to get out of bootloader.
Cheers...
ultramag69 said:
You're looking at the rom version, NOT the SPL. You need to go to bootloader to check your SPL - hold ok button above flywheel, power button and reset with stylus, hold all three in until you get to the tri-colour screen (AKA bootloader). You should then see your IPL and SPL. reset normally to get out of bootloader.
Cheers...
Click to expand...
Click to collapse
Ahhh silly me, well now i feel stupid i was pressing the wrong "ok" button, thanks alot for the help m8.
now i can see
HERM200
IPL-1.04
SPL-2.10.Olipro
Thanks again for the quick reply ultramag69
No worries, just tell other people if they have the same problem... What comes around goes around...
Cheers...
Related
As title is it possible to install the Tytn rom on the orange m3100 without problems?
I have a Hermes 100 (same as the M3100) that failed ROM upgs
I have a Hermes 100, that I believe is exactly like the Orange m3100 that I have tried to flash with both roms and it is now stuck in boot loader mode until I figure out how to get a rom flashed to it. No OS.
I have another one that is also a Hermes 100, the same, that flashed fine with the CHT9000 ROM.
*shrug* Not sure what's up. But I know what's down....one of my Hermes 100's!!!
Re: I have a Hermes 100 (same as the M3100) that failed ROM
holywood63a said:
I have a Hermes 100, that I believe is exactly like the Orange m3100 that I have tried to flash with both roms and it is now stuck in boot loader mode until I figure out how to get a rom flashed to it. No OS.
Click to expand...
Click to collapse
If it's a production model you should be able to flash from the boot loader. If you have tried the method described in the wiki (run the RUU two times, without disconecting the device) and that fails, you can try using the MaUpgradeUt_noID.exe and report if this method works for you.
BUT if it is a preproduction model (the one with 300Mhz processor) then most probably the rom upgrade will fail and you'll need to wait until sombody finds a solution for flashing those units.
Re: I have a Hermes 100 (same as the M3100) that failed ROM
pof said:
holywood63a said:
I have a Hermes 100, that I believe is exactly like the Orange m3100 that I have tried to flash with both roms and it is now stuck in boot loader mode until I figure out how to get a rom flashed to it. No OS.
Click to expand...
Click to collapse
If it's a production model you should be able to flash from the boot loader. If you have tried the method described in the wiki (run the RUU two times, without disconecting the device) and that fails, you can try using the MaUpgradeUt_noID.exe and report if this method works for you.
BUT if it is a preproduction model (the one with 300Mhz processor) then most probably the rom upgrade will fail and you'll need to wait until sombody finds a solution for flashing those units.
Click to expand...
Click to collapse
how do you tell if its a production or preproduction unit?
Re: I have a Hermes 100 (same as the M3100) that failed ROM
vapor said:
how do you tell if its a production or preproduction unit?
Click to expand...
Click to collapse
The preproduction unit has a 300 MHz processor, without the final button layout and slight different color.
EDIT: See both units here:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello to all professional user:
As I check the informations of the softank with mtty.exe and device infomation, found some questions for CID, radio and rom upgrading.
On device informatin show as following:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Rom date: 07/24/06
On boot mode:
Softbank SPL1.04, IPL1.01
mtty.exe shown the CID is HTCSVODAK801??HTCEUSB, and Level = FF,
(Not SuperCID)
Think the seller in H.K. only did changed the rom from 1.33.761.4 ?? to 1.23.708.4 07/24/06, but didn't made it SuperCID.
I'm wondering how can I use it in H.K. without SuperCID ??????
Because of bootloader version 1.04 is allow to flash rom without checking CID, and the rom date is before 12/01/2006, I assume it can be upgrade to new radio and rom versoin (as XDA reminder: X01HT which sold after 12/01/2006 is not allow to upgrade) !!! Am I right ?
So, can I make it SuperCID with " HTC_Hermes_SIM_Unlock_v2a " software pack and SSPL-HERM.exe under the above conditions ?
If not, is it possible for just bypass the procedure of SuperCID and go ahead for radio and rom upgrade ?
Thanks for your reply first,
I just wanna know, base on the existing hardware and software conditions, does my machine can/need unlock or not?
Because I'm afraid it hangs after update the AKU3.3, thanks thanks thanks !!!
I also got my Softbank X01HT in HKG, Mongkok to be precise and it was also flashed with Dopod rom 1.23 (english version). I just made it supercid as per instructions contained with in the wiki. Since then I have flashed it with the SA HTC rom 1.35 then downgrade the BL to 1.04 and have now loaded aku 3.3 HTC Test rom. All in english. I believe if you spend sometime reading the upgrade procedures contained in the wiki you will have no probs however I cannot comment on the chinese roms. This is a great site with some truely clever people working on these devices
Thanks the reply !!!
What is your SPL at first ??? does it unlocked before your flash the new rom ???
ricorico said:
Thanks the reply !!!
What is your SPL at first ??? does it unlocked before your flash the new rom ???
Click to expand...
Click to collapse
Originally it was SPL 104
When I flashed it with the SA rom 1.35 it went to SPL 109 so I downgraded back to SPL 104.
Now I have flashed it with HTC test rom aku3.3 and it is SPL 109 again
Now I been reading all of the stickies and after much confusion and some more readin i found myself into the correct Vista RUU loader, now for the ROM I found through orange one that has an extension of .nb0 and one on this forums ftp of .nbh which is the one I should be using once I do the soft spl and cid unlock?
I also kept getting a error connection saying my update utility is out of date, then with the Vista one(after installing all drivers etc) I get a connection error but only with those tool I am able to connect with the vista mobile device center with no problems before and after installing the 32bit drivers, should I be trying to load the files in the main phone menu or in boatloader? Cause I've tried both ways and receive the 2 previous mentioned errors.
I just don't know what I am doing right with those, if helps you guys help it is a Orange M3000 with I believe german ROM...sorry If I couldn't find the answer I have been reading for a few hrs before I decided I need to post for proper direction on doing this....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ahh, well, let me commend you brother for actually reading and searching before posting a problem! Much appreciated! But lemme ask you this...what is your phones info? IE-IPL/SPL, is it a G3 or G4? Once you can provide us that information, then would should be able to better assist you!
Sorry forgot that info for the SPL, I know its a G4 since the examples I read talked about the 3 leading 0's, but specifically it is
IPL/SPL: 2.16.0001
GSM: 01.04.10
OS: 2.16.1.1
Mkay, what I would recommend is going ahead and Hard-SPLing your phone(look for the Hard-SPL thread in this subforum, and follow the instructions EXACTLY!), and then upgradeing your GSM radio ROM to 1.69.X or something similiar, seeing as the one that you have is REALLY old. Upgraded radio ROMs offer better connectivity then older ones do. After you do both of those things, you can then safely upgrade to either WinMo 6 or 6.1...hope that helps!
Tried the HardSPL and got this:
Do I need to have a ROM(nb.nbh) loaded in the same folder as the Hard-SPL.exe I used?
No ! you don't have to have a Rom in the HardSPL folder,just Activesync with pc and run the HardSPL,it'll start to flash,don't worry if the screen goes white,it part of the procedure,but I assume you are trying it on WinVista.HardSPL doesn't work on Vista,better try on a pc with WinXP.
Ok, new to HD2, just tried to flash
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[ROM][WWE][--grzegorz10_Dusk_Ultimate_2_v1.20--]
to T-Mobile US HD2 and it wouldnt go past 1%. Errored to recovery. Is it bricked, did I flash a non-compatible Rom?
Is there any way to recover? Tried T29, no go past 0%.
Any help please tia
huggs said:
Ok, new to HD2, just tried to flash
[ROM][WWE][--grzegorz10_Dusk_Ultimate_2_v1.20--]
to T-Mobile US HD2 and it wouldnt go past 1%. Errored to recovery. Is it bricked, did I flash a non-compatible Rom?
Is there any way to recover? Tried T29, no go past 0%.
Any help please tia
Click to expand...
Click to collapse
You must Have HSPL!
- Do a task 29 (not essential, but recommended)
- Flash the 2.10.50.08_2 radio (not essential, but recommended)
- Flash The ROM
- Hard Reset (hold the volume up and down button once the flashing reaches 100%)
- Post your feedback
That's taken from Shu.[OP] that was posted on Cruzer's HD2 ROM. It's what you need to do to flash a ROM. Long as you don't use a .51 radio, you're fine. Example: 2.10.50.08_2 is good for Tmobile USA, but if you had a .51 in the radio, it'd brick your cell. All the basics are covered in the tutorials in the HD2 General forums or just do a search for it. Make sure you do the right HSPL. You can do a search to find that out as well. To get into bootloader, just pull the battery and hold down the bottom part of the volume button and then put the battery back in and turn it on. Hold it till you see the rainbow screen. Dusk is good for TMOUS. I've used it and it's pretty cool.
Think I had wrong radio. Trying to recover now...
huggs said:
Think I had wrong radio. Trying to recover now...
Click to expand...
Click to collapse
Doesn't have to be the one I listed. I use 2.12.50.xx
Dusk Is Compatible with T-Mobile.
To every one that want to know.
Of course Dusk Roms can be used on the T-Mobile US
Reason I am so sure and why veru easy to check is that
all of his Beta Theme has T-Mobile US to flash his test roms
on.
Regards
Obalia73
Hi guys, i've a problem, with HSPL 1-2 or 3 if i try to use LEOIMG.nbh original(taked from RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
During the installation, at 10% it doens't works, it stop and reboot it, with this screen:
RUUNBH
PB811 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
Upgrade ROM code errore
Please try again
What i need to do, to solve this problem? I've try to do task 29 on mtty but nothing, if i try to install a cooked room(after restore HSPL) the installation works.
first of all, this is the wrong section. you should use the Q&A section for such posts.
second, from the info you've provided you don't have HSPL installed.
And you don't need HSPL to flash a stock ROM.
Try flashing it using USB: Connect your phone in bootloader mode (tricolor screen) and wait until it says "USB" then run the RUU setup on your PC, when it tells you to connect using sync just ignore it and continue.
try this
http://forum.xda-developers.com/showthread.php?t=606713
Dr.Move said:
first of all, this is the wrong section. you should use the Q&A section for such posts.
second, from the info you've provided you don't have HSPL installed.
And you don't need HSPL to flash a stock ROM.
Try flashing it using USB: Connect your phone in bootloader mode (tricolor screen) and wait until it says "USB" then run the RUU setup on your PC, when it tells you to connect using sync just ignore it and continue.
Click to expand...
Click to collapse
Yes, so sorry, i ask an Super-User to move this thread.
I've try with this method, but i can't ignore, i can only exit setup:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
pajomoro said:
try this
http://forum.xda-developers.com/showthread.php?t=606713
Click to expand...
Click to collapse
I've try but doesn't work, it doesn't install SPL 1.42 and Bootloader. and i do this operation, only for install it
Please help me, i don't know what can i do
Problem solved! We can close it.
I've Use HSPL 2 for set HSPL1 and i've install my ROM