English:
I tried to downgrade my Charmer from WM6.1 (Diamond Look) withe the official "RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship".
But at 80% it stops and get an error.
So now, i don't have any rom on the device and i don't know how I can rescue the charmer..
Doe's anybody have an idea?
IPL 3.08
SPL 3.08
The charmer gets just the colered display with the red, green and blue stripes.
_____________________
German:
Ich habe versucht, mein Charmer von der WM6.1 (Diamond Version) wieder downzugraden zu WM5, da ich mit der Diamond Version unzufrieden war.
Mit der offiziellen Version der T-Mobile Siete habe ich es versucht:
"RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship".
Jedoch bleibt es immer bei ca. 80% stehn und es dauert eine Weile bis eine Fehlermeldung erscheint.
Jetzt habe ich keine Ahnung wie ich das Gerät retten kann.. mhh
Ich habe gelesen dass ich es mit dieser Version probieren soll:
"AKU3.2-1RC1.rar"
jedoch finde ich diese nirgends zum download /:
bin am ende meines Wissens..
Hoffentlich hat jemand von euch eine Idee..
Liebe Grüße
IPL 3.08
SPL 3.08
Das Gerät starte nur noch mit den drei farbigen Streifen (ROT/GRÜN/BLAU)
Can you get Boot Loader mode?
yes! the bootlader mode is there
IPL 3.08
SPL 3.08
and in the right top corner stands RUU
no the charmer alwys lost connection i think the battery is to low mhh
but i still get the boot laoder
@dorfdisko
u think the battery is low? why u don't recharge and try again?
gReeTs cYBERdEL
Hey cyberdel, you can't recharge the device without ROM. (But back to the Problem) But you can power the device with a 3V Adaptor. Pinn layout is desribed in forum. Then try again. It should work.
hey thanks for this information!
i'll try it and let's see if it works..
I tell you tomorrow if i had succeed
let's hope that it works for you. For me it worked several times.
____________________________________________________________________
Hey!!! MYY CHARMER IS BACK TO LIVE <3
I thank all guys, who supported mee.. thank you very much!!
hey, now my battery is full charged an the ruu starts patching but at 95% ist says:
This NBF File cannot be used for your PDA Phone. Please check NBF File.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
i used this one:
RUU_Prophet_220734_2207114_024721_NVID
i tried also:
Prophet_G3_G4_RadioRom_v2.69.21
RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship
but no succeed
what should i try now?
____________________________________________________________________
Hey!!! MYY CHARMER IS BACK TO LIVE <3
I thank all guys, who supported mee.. thank you very much!!
Use the noId RUU and change the nbf information (Tools are in the forum)
hey my charmer is running again! thanks
Good. Glad that I could help you.
Can you please give me the link to your ROM with which you were able to make your charmer up and running.....
Thanks in anticipation as I am facing the same problem for the last month.....
ChrBeck said:
Use the noId RUU and change the nbf information (Tools are in the forum)
Click to expand...
Click to collapse
Can you please sow me the links to these tools...
Hello! Try to use serarch function in the forum. Anyway here you can find the requested tools.
rmagyar said:
Hello! Try to use serarch function in the forum. Anyway here you can find the requested tools.
Click to expand...
Click to collapse
Thanks but I want tools to change the ROM information as I have to Forcefully install PROPHET ROM into my charmer as at present it give me error at 95% saying invalid command in the same way as depicted in the post #7 by dorfdisko.....
Related
Hello guys,
this is a new thread for my ROM!
Look by yourself:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Because i don't have time to edit three different pages for one change in my rom, I installed MY BLOG to kepp this changes on one place. Please visit if you like my ROM.
Changelog
Removed:
Internetsharing
Lockscreen/Skin
Remote Desktop
SampleMusic
Windows Marketplace (can be downloaded seperately from HERE oder browse with your phone "mp.windowsphone.com")
SqlCeMobile
Themes
Transcriber
Welcome Center
Windows Live
Windows Live IM
WM Widgets
Field Test
Google Maps
GPS CoPilot
Long Press Endkey
MS Facebook
OOBE
RSS Hub
Streaming Media
Changed/added:
BsB G-Config
CFC compressed Manila
CleanRAM 1.9.1
bigger font in SMS-Tab (siehe Screenshot)
Manila language only in german
NetCF 3.7.8345.00
Opera 10 beta 2
Performancetweaks
Pigeon 1.2.5.0
PNGs optimized
PushInternet deactivated
Landscape in Manila
Shake and Save
Softkeys changed to Programme und CommMgr
disabled clock animation
WifiLocations 0.6
If you want to have the original Clock in Home-tab and Slide2Unlock then download the following CAB:
Stock-Clock
newest Changelog
Added:
- S2U2 2.21
- Slide 2 Shutdown
- NoData
- Topaz Keyboard Control
- Back FavPeople Up! 1.3
- MyPhone 1.5.2140
- Total Commander
Changed:
- Clock-Design (Hometab and S2U2)
- Batteryicon in %-steps
- Wallpaper etc. in one (!) design
Hello inselstaat,
Looks very nice. But i would preferred the standard clock. Is there a cab available?
How can i change the background for all tabs?
Best regards
Yoshi
For the Clock: Look in the second post, i added a cab file.
If anybody has got an design-problem i can also make a cab
Also made a cab for the Powerbutton... Slide 2 Shutdown did not start when pressing the powerbutton for long time. See 1st post
___________
Background in all tabs: I used the program HD Wall 0.28b. Just put it into the search box and you can download it.
In this program you can use a profile with CFC compression, because my manila is patched for this compression.
I think its a very good program for creating fast and easy a new background AND task- and softkeybar skinning
I hope i could help you!!
If you install the standard HTC Clock and you want to have my clock back, deinstall Standard-clock-cab and download this rar-archive.
Copy the files inside into "Program Files\S2U2\gfx\clockD" and make a soft-reset. that should work!
inselstaat said:
For the Clock: Look in the second post, i added a cab file.
If anybody has got an design-problem i can also make a cab
Also made a cab for the Powerbutton... Slide 2 Shutdown did not start when pressing the powerbutton for long time. See 1st post
___________
Background in all tabs: I used the program HD Wall 0.28b. Just put it into the search box and you can download it.
In this program you can use a profile with CFC compression, because my manila is patched for this compression.
I think its a very good program for creating fast and easy a new background AND task- and softkeybar skinning
I hope i could help you!!
Click to expand...
Click to collapse
Thanks for your help.
Best Regards
Yoshi
wow
Hi Inselstaat, sehr nettes ROM, leider stehe ich auf die Tasten unten, ist für mich faktisch einfacher zu bedienen.. aber zum mal guggn wars ganz nett ^^
LG
diggyman
Hi Inselstaat, very nice ROM, unfortunatelly i prefer the lower buttons, they are better to handle for me.. but just for a look it was nice^^
Greetz
diggyman
@diggyman,
there is also a very nice 6.5.3 ROM from inselstaat http://forum.xda-developers.com/showthread.php?t=597342
Cheers digidigi123
Someone found a bug that i would have never found: Settings can not be opened from the start menu.
Please look in the first post for a download.
Merry christmas,
Inselstaat
hi
is it possible for us to change the languag to EN in your rom?
thanks
At this time a have no plans to make an english rom. for now, you would have to add the english language to manila, but windows would still be in german.
inselstaat said:
Hello guys,
this is a new thread for my ROM!
Look by yourself:
Because i don't have time to edit three different pages for one change in my rom, I installed MY BLOG to kepp this changes on one place. Please visit if you like my ROM.
Click to expand...
Click to collapse
Mirrors here:
Topaz File Mirror. ->Cooked ROMs->WM6.5>Stone
or
FTP User xda Password xda ->XDA->Cooked ROMs->WM6.5>Stone
or
BeeGee's Disk Station User xda Password xda ->XDA->Cooked ROMs->WM6.5>Stone
I'm now on XWKE7 1.4 by AngeloM, this rom is fast an looks really nice. but flashing this rom wasn't easy for me, got 10-15 bootloops (I think because I was on VillianROM, not sure)
Now it runs!
----->Diese Anleitung ist nur nötig, wenn beim normalen flashen des roms mit Odin bootloop Probleme auftreten
----->this guide is only necessary if you get bootloops by flashing this rom with odin
What i did was
1. Power off Phone
2. Start phone holding Power, Vol up and Home Button (Recovery Mode)
3. Clear Data + Clear Cache
4. Go straight into Download Mode (holding Power, Vol down and Home Button) flash Stock XKE7 Firmware do NOT click autoreboot in odin, NOT BOOT android
5. Go straight into Download Mode (holding Power, Vol down and Home Button) flash Stock XKE2 Kernel do NOT click autoreboot in odin, NOT BOOT android
6. Go straight into recovery mode (holding Power, Vol up and Home Button)
7. Clear Data + Clear Cache
8. Go straight into Download Mode (holding Power, Vol down and Home Button) and flash Angelom Rom 1.4 do NOT click autoreboot in odin, NOT BOOT android
9. Go straight into Download Mode (holding Power, Vol down and Home Button) and flash Stock XKE7 Kernel CLICK autoreboot in odin, BOOT android
10. Finish have fun
(11). After the rom booted successful I flashed [CF-Root v3.5] KE2/7 - su+bb+CWM3 because it wasn't there and now everything is
good luck!
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GERMAN:
Nach gefühlten 10-15 bootloops (ich denke es lag daran das ich VillianROM vorher drauf hatte) läuft (rennt) es endlich.
Ich habe folgendes gemacht...
1. Handy aus
2. Handy starten mit Vol + und Homeknopf und Power (recovery mode)
3. Clear Data + Clear Cache
4. Direkt in den Download Mode gehn (Vol - und Homeknopf und Powerknopf) und Orginal (Stock) XKE7 Firmware flashen, bei Odin Hacken raus bei autoreboot, Android NICHT booten
5. Wieder direkt in den Download Mode gehn (Vol - und Homeknopf und Powerknopf) und Orginal (Stock) XKE2 Kernel flashen, bei Odin Hacken raus bei autoreboot, Android NICHT booten
6. Direkt mit Vol + und Homeknopf und Powerknopf in den recovery mode
7. Clear Data + Clear Cache
8. Wieder direkt in den Download Mode (Vol - und Homeknopf und Powerknopf) und Angelom Rom 1.4 flashen, bei Odin Hacken raus bei autoreboot, Android NICHT booten
9. Wieder direkt in den Download Mode (Vol - und Homeknopf und Powerknopf) und Orginal (Stock) XKE7 Kernel flashen, Hacken bei autoreboot SETZEN
10.Handy starten lassen und Spaß haben
(11).Nachdem das Handy erfolgreich gestartet hatte habe ich
(12).[CF-Root v3.5] KE2/7 - su+bb+CWM3 geflashed, da ich CWM3 nicht hatte und jetzt ist alles !!!
Viel Erfolg!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi there, first THANK all of you for your helpful work in the past years. Ive reading so much on xda and it helped me always so often with my little problems. Thanks!
Now im a proud User of a Lumia 920 - and im lovin it. But at first, i have a few Problems. But i solved it (also with help from the xda-Forum, of course ^-^). And now im thinking, ok maybe i can help too. Ive see a lot of Messages written by German people here and a few from them was asking about Flashing a Lumia 920.
So i wrote a Tutorial, how to flash Lumia 920 Smartphone with a non branded german ROM (but you can use of course any other ROM-File too.) Maybe it helps - and sorry, its in German, cause its my native Language
Again - thanks all for the hints and tipps over the years - and we have a lot of things to do
// Und in Deutsch: Ich habe mal eine Anleitung geschrieben, wie man ein Lumia 920 mit einer ungebrandeten, dt. Firmware direkt von Nokia flashen kann. Das kann unter anderem bei Problemen mit einem Voodafone ROM helfen, welches ja sehr oft als Unlocked Nokia Lumia 920 in den Handel kam. Wenn ihr Probleme mit MMS oder Internet habt - lest das!
Tutorial - How to Flash (in German)
// EDIT
Ok, i grab my few english skills and try to wrote an (hopefully) understandable english Tutorial of this... dont laugh at me too loud
Tutorial - How to Flash (in English)
I have a lumia 920 which is locked to EE network.If i flash with another rom will it also work with other providers?
No unfortunately it will only change the ROM and not Carrier Unlock the device.
That's amazing! Well done.
Any German people care to carry the torch and translate it for the rest of us english speakers? I'd love to be able to flash my ATT Lumia to a Rogers one until I can get it unlocked.
Thank you for this guide. Using your guide I managed to flash my UK Lumia (which has the EE firmware) with the factory default GB firmware.
Does this mean you can flash your ATT phone to Rogers firmware and take advantage of AWS 1700?
Thanks,
Thanks for your support. Glad that i can help some people. I can try to translate this little Tutorial in English too, but then some of you has to help me with the correct grammar
Anyone have success with Internet Sharing when flashing to another ROM?
planing to flash my lumia 920
i want to flash my lumia 920 i have already unlocked veriosn and global rom from italy but i want to change it because it seems the italian rom don't support at the moment 4g LTE connectivity so if i will flash RM821_CV_DE_VAR241810_yelllow the rom of germany LTE will b enabled as i contacted nokia and they told me at the moment maybe nokia didn't enabled LTE for the italian version ? thank you anyway for the great support
Please, next time use punctuation marks (no offense). I think, your question was, if you can flash an german ROM on the Lumia 920 to enable LTE in Italian, right?
Try it. The Language (italian) is still inside, so you can switch after Installing the ROM on your Smartphone. But i dont know, whether the LTE Settings in this Firmware the right ones for your country. It doesnt, you can change the Firmware back...
Dont think, anyone here can help you with this Problem. But it would be nice, if you post your experience, so it might help other people who face this Problem. Good Luck!
how do you know which firmware is unbranded? I want to flash my 820 (RM-825 code 059Q9L) to one unbranded in english (the actual ROM is unbranded but in German), but i can't identify one. BTW, I'm using Navifirm+ to find the lastest one.
Like-wise interested, which one is unbranded, and does it enable internet sharing/allow you to use it?
I have an unbranded Lumia 920. On my package where it came from it says CV (Country version).
Manufacturer Model Name: RM-821_eu_euro2_248
Mobil Operator Name: 000-DE
And yes i can share Internet, here a pic:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
says you can share with up too 8 people, and if its not used after couple of minutes it will deactivate itself...
Penecho said:
I have an unbranded Lumia 920. On my package where it came from it says CV (Country version).
Manufacturer Model Name: RM-821_eu_euro2_248
Mobil Operator Name: 000-DE
Click to expand...
Click to collapse
So, the unbranded firmwares has this "000" followed by the country code were it was sold?
My NL920 that I bought it from Germany had that indicator but I flash it to an Orange UK stock firmware because I had a lot of apps that were not available with that firmware.
I guess so, I know the german Vodafone Lumia 920 has VOD-DE instead of 000-DE
I concur. I have installed the Nokia default firmware for the UK on my phone and it shows the following
Manufacturer Model Name: RM-821_eu_euro1_276
Mobile Operator Name: 000-GB
Carrier: CV GB SW Variant ID 276 v03
OS version: 8.0.9903.10
Firmware: 1232.2110.1244.3003
who know at&t lumia920 can be flash the devloper's rom to unlock sim?
Crack920 said:
who know at&t lumia920 can be flash the devloper's rom to unlock sim?
Click to expand...
Click to collapse
Yeap we should be able to do that and completely unbrand the RM-820 model (the AT&T and Rogers variants) using this method, however the "clean" firmware found on the Developer Edition Lumia 920 is not yet on the server. I personally expect that to be available once the first major update is release for the Lumia 920 from Nokia. Hopefully I am correct...
Now im flashin an Portico-ROM on my Lumia. Its branded from Orange (swiss Operator), but hasnt any looks or limitations - BUT cant use 4G.
Infos:
Model-Name: RM-821_eu_Euro2_345
Operator Name: ORG-CH
Infos (in German) here: http://aydon.wordpress.com/2012/12/21/winphoneportico-schon-jetzt-auf-lumia-920
So should I be able to flash my AT&T branded 920 currently with RM-820_NAM_ATT_US_VAR237330_V1_Black (059L848), to this firmware
RM-821_CV_GB_VAR245507_v2_Black (059R075) ???
Hello to all,
so long story short, my Evo 3D GSM sd card slot has died and it doesn't recognize any SD card.
So I want to return to stock so I could claim my warranty.
I spent hours of google-ing but all of the tutorials are using SD card.
I did change a lot of ROMs over the time, but never did install one without SD card so I could really use some help here, no clue where to start even.
Any help would be appreciated.
Never tried it,but as I read once you should be able to use ADB in Recovery. So you may use ADB Sideload or ADB Push.
Gesendet von meinem HTC One X mit Tapatalk
---------- Post added at 06:17 PM ---------- Previous post was at 06:11 PM ----------
Also U can use a RUU. You have to go into Fastboot,and then enter this command in CMD: fastboot getvar version-main
The number shows your version number,so u can look which RUU Version u have to look for.
Before using RUU u maybe have to relock the Bootloader,try once without relocking. If this fails,just lock the Bootloader again and you should be good to go
Greets
Gesendet von meinem HTC One X mit Tapatalk
TouchscreenLover1 said:
Never tried it,but as I read once you should be able to use ADB in Recovery. So you may use ADB Sideload or ADB Push.
Gesendet von meinem HTC One X mit Tapatalk
Click to expand...
Click to collapse
Ty for reply,
I didnt mention all of my modding knowledge on android is put-the-rom-on-sd-card-and-hit-install. :/
Everything else I did was using the tutorials on web.
So I would need a bit more help.
From what I can find on google ADB Sideload is available from Jelly Bean on (im stuck on ICS) and Android Push just gives me generic results about pushing the file to SD card from PC using ADB.
Thank you once more for reply, but I would need just a bit more info to start researching...
I forgot to mention, my phone is GSM and its S-off.
As i wrote,i also never tried,equals that I have no experience with ADB Methods..
Try the RUU Posibility. I edited my post,take a look That should work definitly!
Gesendet von meinem HTC One X mit Tapatalk
Thank you.
I managed to get my version, its 1.22.720.1
I found a list of RUU-s but cannot find nothing with this number.
http://www.androidruu.com/index.php?developer=Shooter
EDIT:
Ok, I found a RUU I need to use, but I have another problem now.
It will not run. I start the exe file and all I get is error shown in ss.
Any idea?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Look at the RUU Number in the .zip... It's 3.28.40x.x
Yours is 1.22.720.1... So it wont work... Look in the Evo3D Thread,there you should find smth
Gesendet von meinem HTC One X mit Tapatalk
TouchscreenLover1 said:
Look at the RUU Number in the .zip... It's 3.28.40x.x
Yours is 1.22.720.1... So it wont work... Look in the Evo3D Thread,there you should find smth
Gesendet von meinem HTC One X mit Tapatalk
Click to expand...
Click to collapse
Here is the list:
http://www.androidruu.com/index.php?developer=Shooter
there is not single Rom that starts with 1.22. :/
Ohh okayy..I'm sorry, I dont know any other solutions... So you have to wait and be patient,till someone with an Evo3D can help you...
Gesendet von meinem HTC One X mit Tapatalk
Hello, guys. So, I accidentally set a PIN-code for lockscreen of my Amazfit Nexo. Now screen is unclickable, pushing on button is useless too: watches do nothing. Nexo wakes up only when wrist raises. Connecting with Zepp is successfull. Can I do something to fix that?
you have to flash a new rom
Same problem, can't find any rom online. Please help. Thank you
Adrianskiq said:
finde kein Rom online. There isn't any Custom Rom for Nexo Watch! There isn't where they could Create a Custom Rom for Nexo. Saratoga is the One they could maybe Help us ALL. But until, there isn't a Rom to.Flash.
Click to expand...
Click to collapse
Adrianskiq said:
Selbes Problem, finde kein Rom online. Bitte helfen Sie. Vielen Dank
Click to expand...
Click to collapse
Fragen Sie Saratoga79 nach einem benutzerdefinierten Rom auf Nexo Watch. Er könnte helfen, er hat einige C - Rom`s erstellt. Einige Tools zum Erstellen vielleicht. Er hatte mir die Dump Rom von Nexo geschickt. All diese Tools befinden sich auf dem von mir erstellten Thread. Pls. lesen...https://forum.xda-developers.com/t/huami-amazfit-verge-2-alias-nexo-custom-android-8-1-rom.4327773/
there is a Tool here in Forms that can create a Dumping File from the Watch...Use it
Have You Downloaded and Install the AIT Tool? All In One Tool?
TUTORIAL: Unbrick your Huami AmazFit Smartwatch / Xiaomi AmazFit PACE
In case you bricked your watch, here is a tutorial how to unbrick the watch: 1. What is a "bricked" watch? A bricked watch does no longer boot. It typically stops at the boot logo and waits forever. This can happen for example, if a flash of...
forum.xda-developers.com
Download it, installing, starting the PC new, then it should work
EgorRFire said:
Hallo Leute. Also habe ich versehentlich einen PIN-Code für den Sperrbildschirm meiner Amazfit Nexo festgelegt. Jetzt ist der Bildschirm nicht mehr anklickbar, das Drücken auf den Knopf ist auch nutzlos: Uhren tun nichts. Nexo wacht nur auf, wenn sich das Handgelenk hebt. Die Verbindung mit Zepp ist erfolgreich. Kann ich etwas tun, um das zu beheben?
Click to expand...
Click to collapse
Have you Unpaired the Watch into the Zepp App? The Watch should make a Reset so you can Use it fresh like Out of the Box..
2chillen said:
Have you Unpaired the Watch into the Zepp App? The Watch should make a Reset so you can Use it fresh like Out of the Box..
Click to expand...
Click to collapse
So, I've reinstalled Rom with QPST
EgorRFire said:
Also habe ich Rom mit QPST neu installiert
Click to expand...
Click to collapse
Super! That`s the Tool i would write you to use if it shouldn`t to Unbind it.
I was able to boot the watch in fastboot mode, so what can I do now to reset the watch to its factory settings.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}