Problem with upgradting my Tytn - 8525, TyTN, MDA Vario II, JasJam Software Upgradin

Hello all i traied to upgrade my tytn's rom for a cooked rom download from here(HTC_HERMES_S64_WM_6[1].1_TouchFlo2D_UC_V3_WWE_02.10.2008 and V8B1_Manilla2d)
but after it verifaid my info and try to syncronize again, i get an error and it can not syncronize.
what can it be the problem it's open a solve problem wizered and tell me to connect the usb connection again and to remove the battarey...but all of that dont solve it
PLZ help me.

On your Hermes go to settings>system>about>Device Id. Change the name to what your Active Sync id is. It should sync up with no problems...

ultramag69 said:
On your Hermes go to settings>system>about>Device Id. Change the name to what your Active Sync id is. It should sync up with no problems...
Click to expand...
Click to collapse
but it was the same name
as it in the Active Sync
the page that i get is
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Sorry, misread post.
1st thing, If you have Hard SPL v7 installed (hold power, OK button above flywheel and reset with stylus. Hold in until you get to tricolour screen. If you have Hard SPL V7 then the SPL will be 2.10 olipro) you can use the sd card method. This is my preference as there are no "sync errors", EVER... Also its harder to screw up the flash as the only way is to reset in the middle of a flash or have the battery die.
To get Hard SPL go to this thread - http://forum.xda-developers.com/showthread.php?t=296722 . Post 1160 on page 116 tells how to use sd card to flash Hard SPL.
Once you have Hard SPL.....
1. Format an sd card fat32. Copy the .nbh file from the os you want onto the sd card and rename to "hermimg.nbh".
2. Put sd card into Hermes and reset into bootloader (how to find out what SPL you have as above). It should recognise the Flash file and tell you to push the power button to continue if you haven't messed up the first step.
3. Follow the instructions...
Please remember to backup your contacts first though with Pim backup or SPB backup or you will loose them... Before formatting the sd card make sure to backup this on your pc too... Also make sure you have good battery power.
Really easy, but take it slow and DON'T skip ahead and miss a step or you will end up with it either not working OR a brick.
Cheers...

10X for your help
i tried to do what you said
1. download hardspl v7 from the first post
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done.
I didnt undrestand part 3 how can i know if the micro SD on my phone is formatted as fat32?and how to format it?
I copied the file HERMIMG.nbh to my micro SD and run the sspl.herm.exe
and i got the rri-color screen but it stuck on it and do nothing.

l1234 said:
10X for your help
i tried to do what you said
1. download hardspl v7 from the first post
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done.
I didnt undrestand part 3 how can i know if the micro SD on my phone is formatted as fat32?and how to format it?
I copied the file HERMIMG.nbh to my micro SD and run the sspl.herm.exe
and i got the rri-color screen but it stuck on it and do nothing.
Click to expand...
Click to collapse
you dont know how to format a card? its just like formating a hard drive.
put the microsd in your card reader
right click on the icon in "my computer" that is your sd card ***MAKE SURE ITS THE SD CARD AND NOT A HARD DRIVE******
select format
in the file system drop down select fat32
click start and wait for a finished message
copy over the rom image and sspl.herm.exe
place the card back in your phone
run sspl.herm.exe from your phone
then a white screen should show shortly after the tri-colour screen, press the power button to flash (as it says on the screen).
do not place anything else on the sd card also backup the card if you have anything on it.

skeeve666 said:
you dont know how to format a card? its just like formating a hard drive.
put the microsd in your card reader
right click on the icon in "my computer" that is your sd card ***MAKE SURE ITS THE SD CARD AND NOT A HARD DRIVE******
select format
in the file system drop down select fat32
click start and wait for a finished message
copy over the rom image and sspl.herm.exe
place the card back in your phone
run sspl.herm.exe from your phone
then a white screen should show shortly after the tri-colour screen, press the power button to flash (as it says on the screen).
do not place anything else on the sd card also backup the card if you have anything on it.
Click to expand...
Click to collapse
ok great i did it
i try to update the rom HTC_HERMES_S64_WM_6[1].1_TouchFlo2D_UC_V3_WWE_02.10.2008
maybe there is more updating one?
now after i open the file RUUWrapper.exe
it choose for me
spl-2.02/2.10/2.30 new bootloader
and checked the is it hard spl
so when i start to upgrade on my phone there is a screen
Herming.nbh-
IPL-
bootloader
then i press the power button
and all above is OK
and get the
Update complete
update success
but on my pc i get an error
what is wrong again?

TyTn II Rom Upgrade issue
Hope someone can offer some advice...
I have a TyTn II phone I am trying to upgrade the ROM image to 6.1 Pro. Here are the details:
HTC TyTn II
IMEA: 35575701121357201
SN: HT739GB14803
Current ROM Image: 1.56.405.5
Date: 8/28/07
Radio: 1.27.12.11
Protocol 22.45.88.07W
P/N: 99HCY146-00
I downloaded what I thought was the right ROM image from the HTC website but:
The error I get is:
ERROR [294] : INVALID VENDER ID
This phone was purchased in Dubai so I downloaded the RUU file from the Middle East download site. The file I have is:
HTC TyTN II_RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.17.56_Ship.exe
Any thoughts to help me find the right file and procedure for upgrading the ROM

RonEB, Wrog forum dude, you want the Kaiser forum. Thatswhat your phone is and you'll get more help there.
l1234, instead of using the pc, you can now use the sd method to flash your OS. I find it HEAPS easier and a hell of a lot safer too...
1. Copy the .nbh file of the os onto the sd card. (Didn't say format fat32 as you did already), rename to Hermimg.nbh.
2. Put sd card back into phone and reset to bootloader.
3. Follow the prompts.
This should work with no problems... I personally HATE using the pc as there are tons of things that can and do go wrong. Just make sure you have good battery charge left (minimum 50%.
Cheers...

ultramag69 said:
RonEB, Wrog forum dude, you want the Kaiser forum. Thatswhat your phone is and you'll get more help there.
l1234, instead of using the pc, you can now use the sd method to flash your OS. I find it HEAPS easier and a hell of a lot safer too...
1. Copy the .nbh file of the os onto the sd card. (Didn't say format fat32 as you did already), rename to Hermimg.nbh.
2. Put sd card back into phone and reset to bootloader.
3. Follow the prompts.
This should work with no problems... I personally HATE using the pc as there are tons of things that can and do go wrong. Just make sure you have good battery charge left (minimum 50%.
Cheers...
Click to expand...
Click to collapse
thanx but what did u mean by reset to bootloader is to click on SSPL-HERM.exe in my phone? and what is "3. Follow the prompts."
all of that i did:
1. Copy the .nbh file of the os onto the sd card. (Didn't say format fat32 as you did already), rename to Hermimg.nbh.
2. Put sd card back into phone

press and hold the "okay" button on the left side of the phone then press and hold the power button then press the rest button on the botttom of the phone to enter boot loader mode.
the phone will pickup the rom on the sd card ad u just follow what it says on screen.

skeeve666 said:
press and hold the "okay" button on the left side of the phone then press and hold the power button then press the rest button on the botttom of the phone to enter boot loader mode.
the phone will pickup the rom on the sd card ad u just follow what it says on screen.
Click to expand...
Click to collapse
i did it but i dont see any changes
in the settings>about
it still
windows mobile 6
ce os 5.1.195

You press and hold the ok button, power button and reset with stylus until you see the tri-colour screen (bootloader) flash up. It will then recognise the flash file. I believe you just reset the phone which will do nothing.
You DON'T need to use the SSPL.exe file now as you have Hard SPL. Its safer to use than SSPL.
If it works properly it should say "hit power button to start update". Hit power button. At the end it should say "update complete, reset phone", use stylus to soft reset phone. IE... 3. Follow the prompts...
Cheers...

ultramag69 said:
You press and hold the ok button, power button and reset with stylus until you see the tri-colour screen (bootloader) flash up. It will then recognise the flash file. I believe you just reset the phone which will do nothing.
You DON'T need to use the SSPL.exe file now as you have Hard SPL. Its safer to use than SSPL.
If it works properly it should say "hit power button to start update". Hit power button. At the end it should say "update complete, reset phone", use stylus to soft reset phone. IE... 3. Follow the prompts...
Cheers...
Click to expand...
Click to collapse
i did what u wrote "press and hold the ok button, power button and reset with stylus until you see the tri-colour screen (bootloader) flash up. It will then recognise the flash file."
then it was
HERMING.nbh-
IPL-
BOOTLOADER-
press power button
to start update image
i pressed
than it was
HERMING.nbh-ok
IPL-ok
BOOTLOADER-ok
update complete
update success
===========
it didnt said
"update complete, reset phone"
but i did a soft reset with stylus
and it seems nothing changed

Either flash a different rom on then check again or check the list of apps against what you have on your Hermes now. It could be you already have updated the rom. Try PDACorner V18? (could be 25). On my Hermes it reads, in Settings>System>Device Information -
Rom Version: PC_Pro.V18
ROM Date: 07/30/08
Radio Version: 1.54.30.10
Protocal Version: 32.87.7020.20H
The important thing is it will change your ROM version so you can see if it has been changed.
Cheers...

ultramag69 said:
Either flash a different rom on then check again or check the list of apps against what you have on your Hermes now. It could be you already have updated the rom. Try PDACorner V18? (could be 25). On my Hermes it reads, in Settings>System>Device Information -
Rom Version: PC_Pro.V18
ROM Date: 07/30/08
Radio Version: 1.54.30.10
Protocal Version: 32.87.7020.20H
The important thing is it will change your ROM version so you can see if it has been changed.
Cheers...
Click to expand...
Click to collapse
what is the PDACorner V18?
i look for the Device Info and it is:
Rom Ver. 3.22.110.1
Rom date 01/04/07
Radio Ver 1.16.00.00
protocol Ver 32.53.7018.01w
so it seems that it isnt update

The rom I use is PDACorner v18(?) or 25, can't remember which one.
If you change the rom to one of these you will see the difference straight away.
Cheers...

ultramag69 said:
The rom I use is PDACorner v18(?) or 25, can't remember which one.
If you change the rom to one of these you will see the difference straight away.
Cheers...
Click to expand...
Click to collapse
i tried to upgrade with HTC_HERMES_S64_WM_6[1].1_TouchFlo2D_UC_V3_WWE_02.10.2008
the rom that you use is more good than that?

Personal choice, as all roms are.
If you did succeed with flashing SB64's rom then reflashing won't change anything. Using a different rom will. The ones I suggested will DEFINATELY change the rom name.
To find a rom you like, you will 1st have to decide what you want included. I can tell you what I use BUT it may not be what you require. There are NO wrong ROMs, just personal choices. Look in the WM06 section of te forum, there are always a heap of cooked roms there.
Do some reading, they are always described pretty well by the chefs as to what they include. I like SB64's roms but find that, because I have 3rd party apps I like, they are a little "stuffed" with apps I don't use or like , leaving no room for the stuff I want.
Cheers...

ultramag69 said:
Personal choice, as all roms are.
If you did succeed with flashing SB64's rom then reflashing won't change anything. Using a different rom will. The ones I suggested will DEFINATELY change the rom name.
To find a rom you like, you will 1st have to decide what you want included. I can tell you what I use BUT it may not be what you require. There are NO wrong ROMs, just personal choices. Look in the WM06 section of te forum, there are always a heap of cooked roms there.
Do some reading, they are always described pretty well by the chefs as to what they include. I like SB64's roms but find that, because I have 3rd party apps I like, they are a little "stuffed" with apps I don't use or like , leaving no room for the stuff I want.
Cheers...
Click to expand...
Click to collapse
GOOOD IT WORKSSSS THANK U ALL i upgrade to PDACorner v 25
i will try to upgrade to SB64

Related

SX56, problem during rom update

Hi
Started program - found SX56. Message "Upgrading - will take about 5 minutes"
on pda. Then it said that it had a problem with the USB or COM connection, and
to fix it in device manager. I opened Device Manager, and checked that all the
USB and COM ports were enabled, which they were.
By this time, the unlock software and ActiveSync had stopped running. The pda
was still stuck on the "Upgrading - will take about 5 minutes" screen. Since
the configuration has changed, ActiveSync will no longer recognize the device,
and will not sync with it. Your software will not connect until ActiveSync does.
All that comes up is the "Upgrading - will take about 5 minutes" screen. there
is no other functionality to the system.Hard or soft resets make no difference.
Active Sync doesn't work. The PDA has changed its configuration, so active
Sync doesn't recognize it. When I plug it in, Active Sync sees something, but
can't even tell that it is a pda, and I can't even set up a new connection with
it. let alone use the old connection.
Can anyone help? is there a way i can reinstall active sync or is there another way to fix it? please help
You will need xdatools, sd card, card reader/writer and rom file from kitchen for sd card flashing. Unzip the rom after download, start xdatools on your pc, choose the unzipped rom file as source and the drive letter for your sd card as destination from drop down menu, once the card is programmed insert sd card to phone, push reset while holding power, when prompted you then push the action key which is centre of 4 way rocker buttons. Once flashed push the unscrewed stylus into hole next to headphone socket, push once only, wait one minute push once more, this will work as long as you dont have a problematic version of bootloader on your phone. Good luck.
System is entirely backed up onto SD card.Can't use SD card. Can't use PDA.
PDA is still stuck on "ugrading - will take about 5 minutes". It apparently has
no operating system in ROM. No difference with hard or soft reset - comes back
to same screen, no function in PDA.
HELP PLEASE
I think you misunderstood, a normal backup is no good, you need to program an sd card with a new rom, when this is placed in your xda and soft reset it should reprogram your phone with a new rom. You are correct when you say it has no rom, the method I described should restore your phone to a working machine. You do not need a rom to reprogram using bootloader/sd card method, try it and see.
You will need xdatools, sd card, card reader/writer and rom file from kitchen for sd card flashing.
Click to expand...
Click to collapse
Okay, so can I basically use the newest ROM which also unlock the device too?
You will need to use either xda developers special edition rom to unlock or include the unlock program from the kitchen in a 2002 rom, you can then upgrade to wm2003 if you wish, you cannot unlock under wm2003 so you must use special edition or kitchen rom based on 2002 first.
I am sorry if i keep asking you questions.
I do have the xda special rom, ive tryed using it but it caused the problem i do have right now.
i did download xdatools by jeff. i cannot run them though.
Could you describe step by stef of what i need to do.
i.e. do i need a complete NEW ROM, or can i just transfer the xda special rom to my SD card and then run it to restore my device?
But i guess not, else you wouldnt have explained what i need to do.
Thats the error i get when i try to run xdatools. (I dont understand the install note)
"INSTALLATION
From the source + exe distribution copy OsImageTool.exe and itsutils.dll
to the programme A directory as created by unpacking
jeff's-exe (http://cuba.calyx.nl/~jsummers/XDA/) to a directory in
your "Program Files" directory. Then run 'OsImageTool --register'."
IF you unzip the files you already have both of those files in the folder.
THANKS FOR YOUR HELP
You have to install ActiveSync.
You can get it diretcly from Microsoft for free....
HTH
Stefan
. I was able to locate the NK.nbf file. I ran the XDA OS image tool, to put the OS on the sd card, from the NK file. That apparently succeeded, but it is hard to tell. After loading the OS, when I take out the sd card, then put the sd card back into the sd card reader, it can no longer read the sd card. I can format the sd card again, using my camera, so the sd card is not destroyed.
Wher I put the sd card in the SX56, there is no problem, but there is no success.
Pushing soft reset alone does nothing. Pushing the power button alone does not turn the machine on or off, and does nothing.
Pushing power and soft reset at the same time, gets me the “Wallaby Bootloader V5.15” screen. It first says “wait”, and then says “GSM OK”. It then does nothing else, and doesn’t prompt me to do anything else. If I push the action button, I get “DIAGNOSTICS GPRSA 20324e4”. From there, I can scroll up and down, and test the RAM, Display, battery, USB, etc – all items tested seem OK. There is nowhere to go from here – all it does is test the pieces.
After that, if I push the hard reset (the one that disconnects the battery), the power goes off, and the screen is dark. This is the only way to turn the machine off at the moment. If I push hard reset again, it comes up with a screen full of lines, with two blank holes in it (see attached file). From there, none of the buttons do anything, except hard reset (which turns the machine off again), or soft reset + power, which brings up the bootloader screen again.
have the siemens ROM. It will not work with the cradle, because it cannot find the pda if Activesync can’t make a connection, and loading it onto the SD card does nothing new – both results are exactly the same as with what described above.
any suggestions?

Major Problem with XDA

Hi all, first post from an XDA newbie - be gentle!!
I've inherited an 02 XDA from my brother as it's not working & he's upgraded.
I'm trying desperately to get this thing to work. He installed the xda-developers Special Edition ROM V1.2 (according to the front screen - it says in red in the bottom corner 3.17.83 , it also has a red G and R above this)
It doesn't seem to hold a charge very long, which suggests the internal battery is dead. I've read about the light in the top right corner of the unit - I've never seen this lit except once when it went red for a few seconds.
When its sat in the cradle, it seems to work ok. I've checked the Version etc, and it reads:
ROM 3.17.03 ENG
ROM Date: 5.15.03
Radio Version:
Protocol:
I want to reinstall the XDA ROM to see whether it works with the "official" ROM.
I've tried to do a soft reset, I get the stripey screen with WALLABY BootLoader V5.22. After the WAIT sign, I get GSM ERROR, which ties in with the above Version Info in that there is no Radio Version number?
When I press the Action key, I see GSM turn ON Please Wait - then after waiting I get GSM turn ON fail!!
Can anyone tell me how to do the following:
1) Get the official operating system from the o2 website onto an SD Card
2) Get the XDA to boot from the new operating system
I can see from the 02 website that there are 2 downloads, RUU and RSU. I guess one is the OS and one is the radio unit (gsm settings??)
I have a laptop with SD Card reader built in, and a blank 256mb SD Card.
I apologise for the length of this posting, but I have no idea what I'm doing really! Any advice / help would be appreciated.
Thanks, Steve
PS - also tried a hard reset, but first press switches off the unti, and it stays off after the second press - HELP!!!!
YOur GSM Part is corrupt.
Flashing a new ROM wouldn't solve the problem....
Try this:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
Stefan
thanks Stefan.
I read the link, how do I install the ROM to the XDA unsing SD Cardreader & Bootloader?
Sorry for the obvious questions - I appreciate your help!
Steve
this is just rom though not radiostack
Ok here you go, its a little outdated but its what I still use:
Qman's how to use XDArit to write nk.nb1 or nk.nbf to your SD card aka the Bootloader Method!
1. Place XDArit and the nk.nb1 or nk.nbf file in the same folder and start XDArit.
2. Select your SD card (disk drive) from the drop down menu.
3. Select Write to SD
Notice that the Windows CE box is already checked so just click the browse button at the end of that window.
4. Select your (nk.nb1 or nk.nbf) image and then Open
Notice by default XDArit will open looking for a *.nb1 file but if you're going to use a .nbf file you'll have to manually change the "Files of Type" to *.nbf
Notice that nk.nbo / nk.nbo was automatically added as your boot-loader and its check box is unchecked so leave it that way and click OK. XDArit should start writing to the card.
When XDArit has finished writing the image put the SD-card into the XDA and hold the power button and soft reset. You'll be taken to the below screen:
SD DOWNLOAD
Card Type:
CE OS & BOOT
Press action to Download
Or
Press REC to Exit
Press action to download and it will start the download/restore from the SD card.
Follow the on screen instructions once its "Completed" which will consist of a "Soft Boot/Reset".
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
Thanks guys, you've been really helpful.
I'll report back when I've tried to do all this stuff.
One more question - I've only got a 64Mb SD Card, is that big enough?
ALSO - in the instructions it says "Select your Rom Image from the Source drop down menu. "
Which file is the ROM image?
nk.nb1 or nk.nbf
and yes 64MB should be enough
The mystery deepens -
I've put the SD Card in the card reader, but when I use XDATools, i can't select the SD Card as the destination for the ROM image file.
I click on the Removable "E" drive in the Explorer style layout, but it's almost like the tool is wantingme to select something, but i don't know what!
FYI, the SD card already has some data on it ( I took it out of my Dads Digital camera!) Could this be the problem?
Thanks

I Need Help PLEASE PLEASE !!

ok my phone is HTC 8525, with WM 6.1 professional . It worked fine for 3 days then it start freezing , before it does that a blue background will appeare ,then it will not let me do anything at all . When I try to touch an icon, it will say something like invalid location or could not find target . I have to hard reset it. sometimes I have to reset it 4 or 5 times a day . , In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ? please help me I truly appricat it . In addition, the mini card will freeze the whole phone is there is a solution like reinstall the whole thing ?
Hmmm, "the mini card will freeze the whole phone"??? Are you referring to the SD Storage Card? Do you have any volatile data stored on the card? Any Today Screen Applications?
If this is the case, try shutting off the phone and removing the card. Then place the card into a card reader, and plug it into your PC. Make a folder on the desktop of your PC, and COPY all the contents of the SD card to the folder.
Now, reformat the SD card in your PC, as FAT32, and default for all characteristics.
Once reformatted, copy all that stuff back onto the SD card from the temp folder on your desktop, making sure everything is returned to it's original locations. Pop the SD card back into your phone and see if it's fixed. Sometimes, corrupted space on the SD card will make the phone behave very badly. Hopefully, this procedure might fix it for you.
-pvs
Yes Sir, i apaologize , i was refering to the SD card . i am just tierd resetting the phone every 4 hrs . do you recomend any shops that can fix the soft -ware . i notices when i start the phone and i go to clean tmp it will say" 8 Fils and 4 folders of 656 Bytes cleard ! . then 5 hrs later the blue screen comes back
After doing what pvs said, and if you still have problems I'd check for bad blocks with MTTY... I would also ,after confirming no bad blocks, would flash a stock rom then reflash wm 6.1 and see if that helps... Cheers...
Wow , how to do all that if you dont mind me asking , actually i took the SD card out i am not in need for it at the moment . can you please help me to do what you said and i truly appreciat it , Great thanks for both of you gents
pvs already says what to do in his previous post...
To check for bad blocks follow this : http://forum.xda-developers.com/showthread.php?t=377389
To Flash a stock rom you need to know what carrier the phone was on. Download the wm6 update from their site and, Making sure you have Hard SPLed your phone, I suggest flashing via the sd card method. Its safer than flashing through pc.
Format sd card fat32. copy .nbh file of the stock rom (you may have to search for it) onto the sd card and rename to "hermimg.nbh". Put back in hermes and reset to bootloader (power button, OK button above flywheel and soft reset with stylus. Hold all buttons until it goes to tri-colour screen). It should recognise the os flash and load up a screen showing 1st boot screen, 2nd boot screen, gsm And os (or something like that as cooked roms don't generally have the gsm part). MAKE SURE YOU HAVE AT LEAST 50% BATTERY!!!!! Follow the prompts... I generally use the sd card method to flash ALL my roms so I don't have problems like usb disconnecting or pc rebooting/hanging or power failures.
Hope this helps you out, Cheers...
BASELABBAS ... Please describe what you are doing when you say that you are "HARD-RESETTING" several times a day. Are you:
1) poking the stylus into the hole at the base of the unit?
- or -
2) holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]?
If you are doing the first ... this is called a SOFT reset. The second is a HARD-RESET, and will wipe the phone clean of ANYTHING outside of what came with the ROM itself.
Since you have posted that you already removed the SD Card from the device, and can (for the time-being) live without it, I recommend you do an ACTUAL Hard Reset (backup anything you need to keep first) via step #2 above, and then be patient about installing any apps. I wouldn't do anything more than sync it up via ActiveSync with your contacts for the first few of days. If things start to go crazy without any third-party apps installed, then I would look into the steps that ultramag69 has suggested ... starting with a flash to a stock ROM.
WM6.1 has been a bit shaky on our Hermes thus far. Some people are getting good results, but a lot of others are having issues like you are describing. I would suspect that your ROM might not be a good match, before I'd suspect bad blocks at this point (and it's a bit easier to test for).
If the stock rom does better on your device, you can try flashing back up to a WM6.1 ROM after that. And if you haven't already, make sure that you have installed HARDSPL before doing any of this stuff.
Good luck,
-pvs
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR]. I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
it looks like i need to update
this what is say
From :
Image Version : TNT.19199
to
image version 2.05.255.1
BASELABBAS said:
Mr. pvs , I am doing the #2 holding down the two soft-keys WHILE poking the stylus into the hole until the confirmation screen appears, and then opening the keyboard and typing 'R' and then [SPACEBAR].
Click to expand...
Click to collapse
OK, well that's definitely a Hard Reset. So your WM6.1 Rom is acting flaky right aftwerwards, eh? I would say it's time to try a different ROM, as we've been discussing above.
BASELABBAS said:
I tried to download Hard-SPL 1[1].10, when I open it on my PC it will give me instructions then when I press upgrade I will see 4 color screen the Sync icon will disappear and then it will say that it lost connections.
Click to expand...
Click to collapse
No ... try Hard-SPL-V7.zip found at the bottom of THIS PAGE. I THINK you can flash it via the SD method if ActiveSync isn't working for you (if not, somebody please correct me). To do this, open the downloaded ZipFile with WinZip or WinRAR and copy the file inside named RUU_signed.nbh to your desktop. Rename it HERMIMG.NBH, and copy it to the root of your freshly reformatted (FAT32) Storage Card. Put the Storage Card into your device and press the side OK button and the power button simultaneously while resetting with the stylus until the tri-color screen appears and turns white. The device will find the HERMIMG.NBH file and offer to upgrade by pressing the Power Key. This will install HardSPL onto your device without the need for ActiveSync. You can also flash ROMs in this manner.
Again, good luck,
-pvs
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
ultramag69 said:
No, You need to run a file from the phone itself to install hard SPLvia sd card. You can find it on page 116 of the hard SPL or how not to brick your hermes thread.
Cheers...
Click to expand...
Click to collapse
Thanks for checking me on that, Ultramag. I had a feeling there was something I was forgetting.
-pvs

Flashed Rom with Expired Windows Beta..

I was trying to flash the RRE_Fuze_Rom_v40_Hybrid rom - only to find out after booting that it contained Windows Mobile Beta - and had expired.. the screen seems to be locked and I cant establish an Active Sync connection to reflash.
I think I saw something before to the degree of putting an image onto an sd card and booting with that in..
Can someone give me some advice on how to re-flash so that I can use my phone.. A link with instructions would be sufficient.
Anyway work arounds are welcome - I don't think I have a mini-sd card reader with me at my office so.. i'm open to "creativity".
P.S. - sorry if this is in the wrong place.
As it says here: http://forum.xda-developers.com/showthread.php?t=448008
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 using a PC (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Raphael Rom Develpoment Page and unzip/unrar it to your computer
3. Goto the Roms Folder and rename the .nbh file to RAPHIMG.nbh
4. Copy the RAPHIMG.nbh file to the root of your microSD Card
5. Remove Sim Card and Restart phone
6. Plug the microSD Card into the phone
7. Press and hold the volume down button, then press the reset button with the stylus. Release the volume down button when bootloader tricolour screen appears
8. Follow the onscreen instructions to start flashing
9. Once phone finishes flashing and says Update Complete, reset with the stylus
10. When it gets to the screen where it configures the stylus, HARD RESET
(hold the VOLUME DOWN and ENTER (center) Buttons, press the RESET button with the stylus tip, then release the RESET button but continue to hold the VOLUME DOWN and ENTER buttons until the reset screen appears)
11. Follow onscreen instructions to set up your New Rom
Click to expand...
Click to collapse
Hope that helps ^^
Thank you so much.. I think i'm back in action now!
Zeraven said:
As it says here: http://forum.xda-developers.com/showthread.php?t=448008
Hope that helps ^^
Click to expand...
Click to collapse

[Q] I messed up, total noob!! Plz help?

Okay, I was able to install the HSPL to 2.08. By the way I was on T-mobile stock Win 6.5. I installed MAGLDR 1.13 and I verified bothh are installed. When I tried to load NAND Android, could not find the loader.exe or daf.exe to install. I have a phone right now in the bootloader menu. I just want to go back to Win Mo 6.5, I downloaded stock from T-mobile website, but the PC does not recognize the device (has it as MAGLDR device). I would really appreciate any help that you could give. I have searched the forums for this topic, can't seem to find a solution that works. When I tried to install WinMo 6.5 it says it could not communicate with my device (only way I can even see it is to select USB mass storage in bootloader menu). USB flash says USB, but nothing happens. Windows device manager doesn't recogniz device either.
I will never attempt this again, and thanks again for any help you can give.
okay, things should turn out okay.
if you want to proceed with nand:
* When your phone Reboots it will Enter the MAGLDR Boot Menu Screen *
1. Press the 'Volume Down' button to goto Option 5: USB Flasher and press the 'Call' button (far left of the 5 hardware buttons at the bottom)
2. The menu will enter Android Flasher mode and install usb drivers if not present
3. Browse to the folder you extracted your NAND Android Package files to on your pc, right click on Run DAF.exe (or Install.exe if DAF.exe isnt present) and select Run as Administrator
4. Read ALL the text and then select 'Next'
5. Read the information and select 'Next'
6. The installer will now detect USB and then flash your Android Rom to NAND
* You can follow this progress on your Phones Screen *
7. When flashing is complete your phone will Reboot and proceed to boot Android from NAND
Click to expand...
Click to collapse
for an example of a daf rom use: http://forum.xda-developers.com/showthread.php?t=917590
from: http://forum.xda-developers.com/showthread.php?t=893948
to return to wm:
flash rom from sd card:
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Click to expand...
Click to collapse
from: http://forum.xda-developers.com/showthread.php?t=653614
Tina Raymond said:
Okay, I was able to install the HSPL to 2.08. By the way I was on T-mobile stock Win 6.5. I installed MAGLDR 1.13 and I verified bothh are installed. When I tried to load NAND Android, could not find the loader.exe or daf.exe to install. I have a phone right now in the bootloader menu. I just want to go back to Win Mo 6.5, I downloaded stock from T-mobile website, but the PC does not recognize the device (has it as MAGLDR device). I would really appreciate any help that you could give. I have searched the forums for this topic, can't seem to find a solution that works. When I tried to install WinMo 6.5 it says it could not communicate with my device (only way I can even see it is to select USB mass storage in bootloader menu). USB flash says USB, but nothing happens. Windows device manager doesn't recogniz device either.
I will never attempt this again, and thanks again for any help you can give.
Click to expand...
Click to collapse
Do this cut your phone off then cut it back on by holding the volume down button and momentaraly holdind thd power(end) button. When the tri color bootloader comes up plug your phone into the USB cable and wait for the white bar at the bottom of the phone screen to say USB ans then run the update utility for the T-Mobile ROM.
Thanks for the prompt reply. I think I am going to go back to 6.5. When I went to the folder I xtracted for android, I could not find a run.exe or install/ It loaded three files, boot, system, and some other file. None of them had those listed in the files. Like I said, I shouldn't have even attempted it.
Now, when I flas back to WinMo, will it only be on the SD card?
were those three wrapped in a .zip when you downloaded them? sounds like you may have a zip nand rom, but are following daf nand instructions.
got a rom filename for us?
Thanks for the prompt reply. I think I am going to go back to 6.5. When I went to the folder I xtracted for android, I could not find a run.exe or install/ It loaded three files, boot, system, and some other file. None of them had those listed in the files. Like I said, I shouldn't have even attempted it.
Now, when I flas back to WinMo, will it only be on the SD card?
three folders, not files, system, boot and meta-inf.
You unzipped a zip nand rom, then followed daf nand rom instructions.
Tina Raymond said:
Thanks for the prompt reply. I think I am going to go back to 6.5. When I went to the folder I xtracted for android, I could not find a run.exe or install/ It loaded three files, boot, system, and some other file. None of them had those listed in the files. Like I said, I shouldn't have even attempted it.
Now, when I flas back to WinMo, will it only be on the SD card?
Click to expand...
Click to collapse
No you will just be using the Sd card to flash the ROM if you go the SD card rout, and by the way when you are done flashing your phone you can remove that file from your SD. Flashing with the SD card is just a easier and safer way of flashing seing as the only thing that could go drastically wrong is the battery die or you remove the SD card while the flash is in progress. Also flashing from SD takes a littke longer too.
Edit: You well lose HSPL and MAGLD by using the SD card method.
You are right! Unfortunately I got frustated with it and I deleted the files. Here ia the one I tried [23.FEB.11][ZIP][LEO512][LEO1024]CMYLXGOs Stock Desire HD(2)[RUU1.84][RAFPIGNA 1.7OC]
--------------------------------------------------------------------------------
Looks like ALL IS well when download the stock. Thaks T-macgnolia! Actually thanks everyone! My husband thanks you as I didn't destroy his phone.
Okay, last thing I hope. I was able to get 6.5 up and running. Everything works except the battey will not charge. (the little charging icon does not show up in the status bar on top) The battery ia down to 2 percent, when I plug it in the battery goes to full and the led light blinks red, then green all the time. I pulled the battery to reset, doesn't help. What did I do?
Oops, flashing light indicates faulty battery or battery charging circuits. Check battery pins aren't a little bent, perhaps borrow a battery from friend / shop and see if it still happens.

Categories

Resources