Related
please plesae help my spv m3100 flashed wrong
now my phone stop on boot screen and i want to reflash it but it stop on 1 %
my ipl is 1.04
and my spl is 2.03
now what is the solution for me
dvdaio said:
please plesae help my spv m3100 flashed wrong
now my phone stop on boot screen and i want to reflash it but it stop on 1 %
my ipl is 1.04
and my spl is 2.03
now what is the solution for me
Click to expand...
Click to collapse
Try a couple things...
1. Hard Reset
2. Flash a ROM starting at the botloader screen on the phone (put in bootloader, THEN plug into USB)
3. Use mtty, try the task 28 command.
Your solution like everyone else that has bricked there phone on this forum is to start reading. Start with the WiKi and then the 100 page thread on unbricking phones. I'm sure you have a few long hours ahead of you but there is hope at the end of the tunnel
Austinsync speaks truth in abundance! Your first stop should be the excellent unbricking table that dear old Pof compiled, this is in the WIKI and if you are lucky you won't have to go much farther than that...
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
MTTY's "wdata" cmd unlocked on SPL 2.03!Can it Unbrick the bricked ones w SPL 2.03??
I have found a way to unlock "wdata" command in bootloader 2.03!
summary:
In bricked hermeses with SPL 2.03 - NO GSM - KITL disabled, the wdata command is locked. I am not good at programing but I want to know if it possible to change the SPL(bootloader) of bricked hermeses with this command in mtty.exe??!!
How to:
1.Use the trinity splxploit -windows by pof (unbrick.bat). Let the program run for some seconds and then just close that.
2.Do not unplug the usb or soft reset the device.
3.Run mtty.exe and type "wdata" the command is unlocked!
I wanna know can we erase just the CID by erase command and write a CID value using wdata command?
If it can be done then we can unbrick our hermeses!
Yes it enable wdata, you don't need to change CID, if you can load OS.nb, then from Windows use SSPL. But real problem is how to load OS.nb via wdata
need Hermes splxploit -windows ??
i many time write in this forum who can unbrick hermes with spl 2.03 cid locked,no kitl,can not boot,stack in bootloader....only solution is that pof
or good man create Hermes splxploit -windows this will jump spl address and temporaly cid unlock Hermes then we can flash any rom.
I unbrick many Trinity bat wait solution for Hermes???
Bat wait ........and wait.
Zemo znas li ti kako da sredis brikovan hermes cid zakljucan spl 2.03...itd.
Yes, we need pof help, it will be very good to have spl exploit for hermes.
Bas nas dosta ima na XDA, mozes samo preko JTAG koliko je meni poznato ali neznam nikog ko to moze da uradi. Odakle si?
Yes, we need pof help. It will be very nice to have SPL exploit.
Mislim da moze preko JTAG, ali neznam ko to moze da uradi, odakle si?
Bad news people,
The memory layout on hermes is different than on trinity, i already looked
into this and is not possible to exploit it in the same way as I did in
trinity.
I am sorry but I have no time to invest on this now
Best Regards,
pof
Click to expand...
Click to collapse
We can wait for pof, and pray
So, we will wait.......!
I'm a prayer too
So, we will wait.......!
I'm a prayer too
Reply With Quote
Click to expand...
Click to collapse
MY HERMES IS BOOTED OS TODAY!!!
It was half dopod and half T-Mobile...
T Mobile Customanisation: Instalig Dopod stuff???
I soft reset it and it stuck again.
Booted OS
Today my hermes booted os, after soft reset it stuck again. But there is hope, right?
Can you solve No GSM with SD Card Flash?
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Yes, I know that.
If you have similar problem:
1.Leave Hermes without battery for some time, hour or so.
2. DO NOT turn it on, do a HARD RESET*
*If don't work try several times
hardspl v7 or any other after 100% message image corupted
koorosh_bsboys said:
Then Copy Hardspl V7 to the sd card and when your mobile booted into os just run that from your device.
Click to expand...
Click to collapse
Yes i know this bat this will not work if hermes cid locked and stack in bootloader no kitl and gsm.Can not boot os this only work in hermes cid unlocked device then sd card work...bat what i can do when device cid locked and can not connect in activsync and everytime when try to use hardspl v7 or any other after 100% message image corupted only solution is that pof create jumpspl pach that work from dos without activesync this can help me and many other i will donate with paypal if somebody can creat this that work in hermes......
............again harmes how to unbrick 2.03
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
If somebody else create solution before me please sent me message to know??
Do not post any solution from this site i try all and not work(SD card will not work when cid locked,hard spl-not work always 100% then message image corrupted,No kitl.....so please only original solution not from xda-developers..etc.
thanks for all.
Pozdrav zemljacima iz Srbije.
Pozdrav,
Ima nas prilicno sa SPL 2.03...
Igor
gsmhackerns said:
Many people try to unbrick spl 2.03 stack in boot no gsm and kitl mode and can not boot os just led light when power up...can go in bootloader bat this is all!!!.
I speak with imei-check abaout this and they told me that can repair this and it will cost 60pounds+ Here is message from imei-check.co.uk to me Hello,
You must send the device to us. The cost is 60 GBP + 15 gbp postage fee to return it back to you (or 7 GBP if we send it back to a UK address). In the day we receive it, we fix it, and next working day we send it back to you.
If you want to go ahead, please send the device + battery
(i think just need to open temporaly cid unlock in spl and this will help i mean from dos prompt,blank screen+ then flash??)and i must sent from Europe Union country .I live in Serbia and think that solution to unbrick hermes existed bat not want to tell many people......?? I will work in this now and i hope that solution will be for free when fix this.. I unbrick many hermes.artemis...etc..in Serbia bat this solution to unbrick hermes with spl 2.03 temporaly can not not have time to try?. I now will try many solution and will post here when fix this,you can trust me??....
....
Click to expand...
Click to collapse
Glad to hear that.
I am sure that the sulotion for spl 2.03 exists, but we don't know where to find it.
BTW, where is POF & olipro????
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
igord said:
I made some progress, it stuck at OS screen now. It booted os several times today, it is strange that it can boot OS it is IPL 1.04 SPL 2.03. Stil NoGSM
koorosh_bsboys can you hermes boot OS?
Can NoGSM problem be solved with Flashing from SD Card?
Click to expand...
Click to collapse
My hermes can't boot into OS. It has stucked on 2nd splash screen (Imate telstra logo) not the OS logo!
How can u boot into OS?
If you find something new then share it with us.
My HERMES sometimes stuck at second boot scree and sometimes at windows screen, but few times it booted os. Than I put SSPL at microSD, becouse it stuck after few sec when it is on USB. OS is working ok - then I killed it again to SPL 2.03 and today get it back to working OS, No GSM.
What I did to get working OS???
1. Get battery out for about a day.
2. Put the battery in, DON'T POWER ON!!!
3. Do a HARD RESET.
If it don't work try several times.
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
londere said:
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
Click to expand...
Click to collapse
You might need to reflash it. Hold the two soft keys and then push the reset button. it will ask to hard reset. If the phone fails to come on after the hard reset, then hold the left 'ok' key and the power button, and then push the reset under the phone- this will take you to a tricolor screen where you can then re-flash the phone. try reflashing with official rom's, before using any other roms.
yes i do but it still in boot any sugest ipl 1.01 spl 1.40 olipro if any know how to update ipl with hard spl or how to remove hard spl it will be aprecible
My suggestion would be to try using sd to reflash the rom and see if that orks. format sd card making sure its fat 32 then put .nbh file in root directory. rename to herimg.nbh then insert into phone. go to bootloader and it should start the flash straight away. if this works make sure you upgrade spl to olipro 2.10 hard spl so its easier if there are problems. you can possibly upgrade spl this way too (get nbh file and rename hermimg.nbh). I tried this on my herme 100 and it seemed to work. it will flash the spl BUT when it restarts it will go straight to bootloader and start flashing again. as soon as it restarts get the sd card out and put on the os you want to flash. insert card and as long as you've named it hermimg.nbh it should flash new os with spl olipro 2.10. Good luck flashing.
You should read the wiki first : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
your phone can be unbricked using the information on wiki.
only enter to bootloader the ipl dosent start also i fla**** but it stil apear spl.140oli whei in flash it with hard spl 1.10 and when i flash it with spl 2.60 oli it send me a error i try to flash it with qtek-cingular-doppod roms and nothing any suggest
any fu**ing suggest?
also it avoid me to update spl im stuck on hard spl 1.40 and ipl 1.04 i try to flash hspl 260-210 but it refiuses to stay in 1.40 radio 1.27 patched the ipl works but it frezzes with the green led dosent apear nothing
my device still blocked in boot mode i dont know if it is briked the device had the following info
ipl 1.04
spl1.40 oli
radio maybe no
os no
any suggest
any sugest to save my hermes
follow the unbrick guide link that koorosh_bsboys posted
it cant be unlocked its stuck in spl 140 olipro
did you follow the unbrick guide that koorosh_bsboys posted?
just stop trying any unauthorised ideas. let me know if i can help u. i have a friend in o2 service centre here in india. he can get ur device working. he does it by help of a software and 3 cables . it takes about 2 hrs. just let me know if u want ur device to work again
stil zombie my device im getting crazy any ideas
londere said:
stil zombie my device im getting crazy any ideas
Click to expand...
Click to collapse
If you want people to help you, you have to help yourself first!
1st of all, have you gone to read the Wiki as suggested?
2nd what methods have you tried to unbrick your device?
If you can't answer these questions then we can not help you, you keep asking for suggestions but you do not even reply to other's questions!
Here's a good place to start helping yourself if you haven't already http://forum.xda-developers.com/showpost.php?p=1465974&postcount=1
Can anyone please post a guide on how to flash Hard-SPL onto my HTC TYTN.
The guide for installing Hard-SPL onto the HERMES is not available anymore, and i am EXTREMELY confused about what im doing, and i am afraid i will brick my phone if i do something wrong.
Please please please help!
Read the sticky, first post on this page.
It really isn't hard to do. But be sure you know what you are doing btw. SO read the sticky!
Basically you just download the flavor of Hard SPL you want (I used 2.10 which I can recommend, very easy to downgrade to factory SPL again as I just learned!).
After download unzip the folder and run the RUUWrapper. Follow instructions exactly, do nout unplug your device etc. and it should work like a charm. It takes about 1 minute!
If you don't know what you are doing or you are still doubting, wait for Mr Vanx site to come online again or don't flash. There is always a risk you screw up and end with a $500 brick.
So use at your own risk!
Download hard spl v7 from
http://forum.xda-developers.com/showthread.php?t=296722
thanks guys i did it
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
puca said:
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
Click to expand...
Click to collapse
start the device in bootloader, what is displayed?
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Rockford_622 said:
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Click to expand...
Click to collapse
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
hi mrvanx
thanks for your reply after checking the bootloader it has changed to 2.10 olie it did it so fast i thought it had failed will check properly next time and have successfully flashed it to crc 9 and it runs great thanks for all the help
mrvanx said:
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
Click to expand...
Click to collapse
I appreciate your reply Mr. Vanx. Same as with puca, I put my phone into the bootloader mode and it does indeed show the correct 2.10 Olipro version. This is the 3rd 8525 I have had and I could have SWORN it took much longer on the first 2. Even the update from WM5 to WM6 seemed to take much less time with this particular phone. Guess I shouldn't really complain
Downgrade Error 260
Hi Mr Vanx I have followed your guide to downgrade my current SSPL (2.10 Olipro) to SSPL (1.11). But I keep getting error 260. I have followed guide step by step.
I have even tried flashing from SD-Card (by renaming to HERMING.nbh). Process runs successfully, but nothing happens.
Its still showing SSPL-2.10 Olipro in bootloader. Am I missing anything?
Thanks
can some one point me to the guide. I am facing a NO GSM problem on vodafone VPA 1605 with following config:
ROM Version: 1.20.161.6
Radio: 1.03.06.00
CID: VODAP001
Bootloader: 1.04
I do not see the radio version or the IMEI. So I would like to do a HARDSPLv7 followed by Radio ROM update to 1.06.00.10. I hope this will work. Seniors may help with their sggestion.
Can someone help me with the guide to HARDSPL as I am doing it for the first time and the guides are not available at MR Vanx site nor can I locate the sticky?
regards,
H
have you read the first page?
cant uprade from spl 1.40 to 2.04
am using hermes 300 and i want to uprade from 1.40 t o 2.40 but i cant do it.i ve tried can anyone help
dania
How to hard reset without win
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
majida said:
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
Click to expand...
Click to collapse
you should try the hard reset iMate 9502 posts by martin_yo in http://forum.xda-developers.com/showthread.php?t=407336&page=2
Code:
After Flashed with the new ROM, My Device is now stuck in iMate Blue Screen Logo....!!!
But Don't worry Guys...it can be solved with manually hard Reset...
1. Remove battery and reinsert (to make sure the phone is off).
2. Hold down Fn and the Green button (with the phone icon on it) and press the power button.
3. You will see the white hard reset option screen almost immediately. Press the Left Soft Key to hard reset.
Work for me...
but !!
With many thanks Hakim
But I know hard reset of my phone, I did it many time before, unfortunately it dosen't work this time. I tried all I knew about hard reset. but I couldn't do anything for my phone.
I tried (FN+Green+power like last time I did hard reset easy)(FN+Green+reset button)It don't sho any reaction.
Please help me.