Related
Hello,
I recently acquired an i-mate and before doing anything, decided to perform a ROM upgrade. It started with ROM version 1.66.00WWE and Radio version 1.10.00. I followed all the instructions on the clubimate website. The ROM upgrade (Step 1) went well, until I started the English Language customization (step 2). That program froze on my computer and left the i-mate in bootloader mode, even before starting the Extended ROM upgrade for the customizations. When trying to upgrade the main 1.72 ROM again, it gets stuck at the Radio Stack Upgrade (to version 1.14) at 14%, then either exits with no message (Win XP), or gives a Radio Stack Upgrade error message (Win 98 ME). The phone meanwhile says that it is perfuming the radio stack upgrade and to please wait. Waiting for an hour yielded no change. The following is the log file entries of the part for the Radio Stack upgrade:
03:06:42 Connection with USB
03:07:52 Begin Stage 4
03:08:22 Radio Erase retry 1
03:08:59 Radio Erase retry 2
03:09:15 Stage 4 Complete
03:09:15 Begin Stage 5
03:09:15 Write block1
03:09:26 Write block2
03:09:32 Write block3
03:10:08 Radio Update data retry 1
03:10:16 Write block4
03:10:24 Write block5
03:10:32 Write block6
03:10:40 Write block7
03:10:49 Write block8
03:11:25 Radio Update data retry 2
03:12:01 Radio Update data retry 3
I tried many times, but get the same result. I followed all advice on this forum and searched all over for solutions, from getting the device into bootloader mode (power button + action button + reset), making sure that my PC does not have any other USB device connected, that the only programs running are the upgrade utility and ActiveSync 3.7.1, etc.
I also notice it takes approx 1 hour from start of upgrade until the Radio Stack Upgrade, instead of the advertised 30 minutes. Someone mentioned that this Radio Stack Upgrade problem may be caused by a security feature on the Radio Stack ROM preventing the installation of older versions. However, I am installing the newest (ver 1.14), so this should not be a problem. With a hunch, I decided to try the English Language Customization (1.72.800) upgrade again, and the extended ROM upgrade worked, but still no Radio Stack. So now I ave everything upgraded, but a blank Radio Stack.
Now when performing a hard reset, I get the blue screen with "i-mate" written on it. In the bottom right only the version of the ROM "D 1.72.00 WWE" is shown, but it says "No GSM" right above it. It takes approx. 15 minutes to boot (with blue Bluetooth LED flashing), then goes through the screen alignment and intro procedure. After that, it installs customization and boots again. It takes another 15 minutes to boot and the phone functions only as a PDA. Even a soft reset takes 15 minutes (with Bluetooth LED flashing). I tried upgrading again after that, but no use. Going to "Device Information", I see the versions of ROM and Extended ROM, but the Radio and Protocol are blank.
I tried phased upgrading, where I would include the main ROM upgrade file into to the directory where the archive was extracted, then extended ROM, then radio stack. Everytime the radio stack upgrade failed (i.e. stuck at 14%), I would try to upgrade that part only, since all others upgraded successfully.
I am really out of options. Any help would be highly appreciated.
Thanks!
I asked Carrier Devices (clubimate) about this step 2 because on the official download page all I saw was the step 1, no step 2 and no link to download.
The answer I got was there is no english customization 800, only a beta. The customization or step2 would be presented for arabic or telstar etc based on your IMEI # not for english it is contained in the first .exe
So you MUST have got this 800 customization and maybe the main upgrade from on here because it was never on the offical download page. Only the BETA from the FTP which some hacked into on clubimate and posted on here.
Go to the official download page on clubimate (register if you havn't) and dowload the official .exe upgrade (one file) and see if it will run. Don't get it from here.
RUU172126WWE_imate.exe
Hard reset a couple times and that should be it. The upgrade does take a LONG time to do.
If that does not work, you might have to do a warranty repair, I would use the online chat support on clubimate, just watch for when they are online and ask. I don't think you can just flash the radio portion.
I find 1.72 VERY stable and fast. Good luck!
Hmm.. All files were downloaded from the official clubimate website (I had to register in order to download). Talking to customer support, they were aware of the Step 2 customization file on their site (they recommended it, too). I doubt I downloaded hacked ones.
Still a loss on what to do, other than take it to a service center, that is (anybody do that? was it expensive? took too long?).
I tried a suggestion where I extracted the Radio Stack ROM upgrade file from version 1.66 and installing it separately. Still stops at 14%. I also tried a full reflash back to 1.66, but also same result. Took it to an i-mate service center nearby, was surprised that they didn't even know how to put the i-mate into bootloader mode (I had to show them)! All they could do was try reflashing using the same utilities we use (still no luck). They said that anything more elaborate would require sending it to Dubai. So much for "service" center. So, no luck there, either.
Also tried to reflash to the orginal 1.00 ROM with 1.05 Radio: The upgrade utilitiy that came with that version won't go past the small "please wait...." screen. Just sits there.
Really sad. I didn't even use this phone (figured that the best start is to perform a ROM upgrade). I'm not that impressed with how fragile ROM upgrading is (and I am careful with using only official releases). I thought after the Wallaby, things would be more robust. Maybe I shold dump this thing and get an HP h6300 series.
Note that I managed to successfully upgrade to 1.72 at least once. It was only when trying the 1.72.800 customization did things start to go south.
Also, does it matter whether the SIM card is in the phone or not while upgrading? Instructions are not clear, although they did mention that the phone will behave as if it is out of area.
Another question (desperate and a long shot, maybe stupid), Do SIM cards from say T-Mobile have an effect on i-mate phone Radio Stack ROM (i.e. lock it, etc.?)
ANY help would be appreciated!
i-mate and bootloader
I just got to see the problem as I am going through the same search for answer. How to get to the stage of bootloader? Somehow I feel that the device has crashed: While I was trying to install the upgrade RUU172126WWE_imate, my laptop, and for some odd reason, shut itself down, then auto restarted. The i-mate from that point on did not respond and in fact all lights on the device went blackout. I tried soft and hard resets but to no avail. I even removed the battery for several hours and when I re-installed it, all what it gave me was the word i-mate (but no backlight). Any advise on how I can get the device functional again.
Thank you.
Put your device in bootloader (press the Jog button and the Power button at same time and press the reset switch). Place it in the cradle and re-run the upgrade. That should work OK.
Jog
Thanks for the quick reply.
Power and reset button I know, but I am not familiar with the Jog button on the i-mate (Pocket PC PE). Appreicate your help.
Its the multi-directional button in the middle at the bottom. Press it straight down.
Hi guys, I have some experience with rom flashing, and I did it today as usual - flashed HTC 1.35 ... Update stopped at 1%. I tried everything I could to finish the update (It wasn't my first time ). Now, after restart TyTn is flashing with LCD (black & white) & camera led. I can't do anything, even turn it off. Seems like a problem with bootloader. What should I try before i send it for repairing? Do you have any experience with T-Mobile UK? I'm the legal owner of PDA, but I don't have any receipt. Should I contact seller (ebayer) or post it to T-Mob straight away?
Thanks in advance, Jack.
Anyone please?
Check out the wiki for Tytn upgrade problems
I also had this problem, upgrade stopped at 1%....Left it for an hour and no progress. Had to stop update, which then left me at the boot loader screen (tri-color) screen. Tried Hard reset as mentioned above, no luck, still stuck in boot loader, tried to reload rom..got error 262 upgrade error
I had just run the unlocker and set device to super CID, and thought maybe that was my problem, but it wasn't
Luckily the wiki had the answer
Problem 4: Device is stuck in bootloader mode (tri-color screen)
>Disable ActiveSync: connections -- settings -- uncheck "Allow USB Connections"
Remove the battery, put it back in, connect the USB cable, power on the unit (this should allow the USB port to be opened again)
Wait a minute or two, if you get a message that device cannot be recognized just close and ignore it
Open
mtty.exe and select "USB" from the dialog box, then hit Ok.
You should see a white screen, hit enter and you should see a prompt like this: "USB>"
Type set 14 0 (do not copy and paste!!!) and hit enter
Soft reset with stylus
OS ROM and radio version should be back and OS functional, the unit isn't a BRICK anymore!
I had to reload the rom. step 8 did nothing, but return me to bootloader. This time the rom upgrade took about 45 minutes to complete. Weird, but it worked...This is first time in at least 4 rom upgrades with this device and at least 50 other rom upgrades that I ever encountered any issues.
POF...Thanks for the great wiki
http://wiki.xda-developers.com/index...ame=HTC_Hermes
Unfortunately, when it hanged on 1% connection was totally lost. Everytime I tried to run rom upgrade/unlocker/spl downgrader is said no connection. Now I don't have bootloader screen, only flashing LCD & camera diode. Any suggestions?
If you can't get the bootloader running then a service center will be the only solution I think.
Has anybody found the solution to this problem, my phone is doing the same thing. Can't get it into bootloader and screen & camera flash just blinks? I tried everything but to no avail.
Hi mate, have you done anything special or it goes bricked "without help"? I I still haven't put it to RMA because there's no T-Mobile in Republic of Ireland and I'm 2 lazy to go to Belfast
jackass_ass said:
Hi mate, have you done anything special or it goes bricked "without help"? I I still haven't put it to RMA because there's no T-Mobile in Republic of Ireland and I'm 2 lazy to go to Belfast
Click to expand...
Click to collapse
It's bricked trying to update it!!! If i could just get it to the bootloader, i can probably revive it but can't do anything. Can't access USB or nothing, I'll guess I'll send it off to a repair center.
Are there any good repair centers in the US???
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
vallancen said:
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
Click to expand...
Click to collapse
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Erofich said:
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Click to expand...
Click to collapse
When you say booloader mode what does that look like. At the moment if I reboot the phone I get the HTC Mobility windows by Erofich screen.
When you hold down camera and record button and then power on the device I get brifely the white scrren looking for SD card it then goes to the tri-colour screen and does nothing.
I beleive I have CID it as I did the same on this as I did on mine i.e. ran the unlock according to the sticky.
I than put on this
Windows Mobile 6 AKU 0.5.0 (5.2.1711 Build 18165.0.5.0) WWE v5c
Yours i beleive (excellent work by the way)
and it all worked fine bar GPRS I relay needed GPRS so I used
http://forum.xda-developers.com/showthread.php?t=368715
using the clean one which updated fine on my phone but when i tried it on my friends it fell over at about 83% I followed the recovery intructions but this did not work.
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
GnatGoSplat said:
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
Click to expand...
Click to collapse
I am trying RUU_STAR100_3.6.251.0_02.67.30_QtekEUR_Ship I believe this is an original version 5 rom?
GnatGoSplat said:
you can use SDA_ApplicationUnlock.exe to app unlock the phone
Click to expand...
Click to collapse
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
Download regeditSTG2 which is digitally signed: http://4pda.ru/forum/attach/387522/regeditSTG2.zip
Then install it and change some registry values:
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 2
-> change to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 16
-> change to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 128
-> change to 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101a": Dword = 1
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101b": Dword = 1"
Click to expand...
Click to collapse
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Erofich said:
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Click to expand...
Click to collapse
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
vallancen said:
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
Click to expand...
Click to collapse
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
GnatGoSplat said:
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
Click to expand...
Click to collapse
Tried that a couple of times just to make sure I was doing it correctly it goes into the tri colour screen I pressed the reflash option on the PC 1 second later this then sits there for a minute or so and times out "ERROR [260]" the phone did come on and has a USB in the bottom left corner so I presume the connection to the PC is OK.
I have just re-done mine again using the NEO rom (very nice) to make sure I am not going mad and that I did it correctly and this all went without a hitch.
Is there anyway I can get the phone to boot of a SPL on an SD Card I think if I could do this then I could get it back to 5 and start again.
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
GnatGoSplat said:
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
Click to expand...
Click to collapse
Yes tried that made sure formatted FAT32 etc. I know the SD card is ok because if I take my working phone and run the SPL link with the card in my good phone it finds the file and asks me if i want to reflash it. The non working phone with SPL3.06 does not do this.
You are not alone.
The bad news - the person in the post ended up having to exchange the phone.
It could be there's a bug in 3.06 SPL? Seems to be the case because I've flashed bad ROMs many dozens of times on my Cingular 3125 StarTrek and not once did I have any trouble flashing OEM ROM back on it.
Can I write the flash at a lower level with any tools i.e. pdocwrite or seomthing like that?
I don't believe so. Those programs require an Activesync connection (copies files to the phone). You could try the MTTY method, but I don't know if that works on StarTrek. I think it's some kind of terminal access into the bootloader, but what I've said so far is the extent of my knowledge about it.
vallancen said:
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Click to expand...
Click to collapse
I have a similar problem on a 3125 and the phone reports V4.01. I acquired the phone in this condition, so don't know how that came to be. When I try to update via USB, it tells me I need a newer update tool (to match the 4.01, I assume). What error message are you getting when you try to update via USB?
I have been struggling to flash (again) the great pro V2 rom, but I always used my VMWare based XP windows version on my Vista laptop. Today I could use a genuine XP Laptop and I could make a connection and start the upgrade!
Sounds good? That's what I thought too, until the upgrade stopped at 70% (and I didn't touch anything), because of a connection error. I followed the text on my PC screen and I finally it started flashing again for a few seconds and then my startrek suddenly restarted, but it stops at the first splash screen! I tried to get my device back to bootloader mode (push 2 soft buttons and start), but no bootloader mode, only the 1st splash.
I solved the problem.
Thank you for this thread
I tried flashing a new ROM to my i-mate smartflip and thought I had killed it, but going back to the wm5 OEM as suggested on this thread worked and I still have my phone. Now, am I brave enough to try upgrading it to wm6.1 (or even 6.5) again... Once again, many thanks!
somebody can me give the oem rom because i am same problem too on the secreen 3.06 i cant flashing anytihing rom somebody must me help
Hi guys, I've just tried to unlock my ameo and am stuck at the bootloader screen. I have a wm6 rom downloaded and am trying to put it on however, I cannot work out how to do it. I cannot get a RUU to access my ameo as it isn't active sync'd. can anyone tell me which program to use to get the rom on the machine?
thanks
If all its correct the bootloader should say "SPL1.20 olipro"
at the bottom of the page it should say "serial"when you plug athena in the pc USB port it changes to "USB"
Just download a rom appropriate for SPL1.20 unpack it in a folder in your desktop and click in the installer.
Remember that any memory card you may use has to be taken off the athena before you do anything.
also if bootloader do not say SPL1.20 a rom for SPL1.20 wont work.
Hi PBL, thanks for the response.
I have 1.20 listed and usb at the bottom.
I have downloaded the wm6 file but that is all there is, when you say click on the installer, I don't know what you mean, windows asks what to open the file with. Could you give me a link for a wm6 rom with a downloader?
Cheers for any help, I know how annoying noobie questions can be.
Phil
Have you found it out already or do you still need help?
Help still required!
After using AthenaUnlocker for the first time, your bootloader has been updated to Olinex 1.20 (appearing on your screen), however you still might have no ROM installed. => black screen after resetting your Ameo.
Additionally, your Ameo is still locked for other ROMs (as it was with mine), so no unofficial ROM here might work at first. In your case you need an official Ameo WM6.0 ROM found here , if you already have it, the better.
- (Download the ROM onto your PC),
- be sure that your Ameo is turned on and connected to the PC.
- start the romupdateutility.exe (admin rights on the PC, no SIM-card or mini-disk inserted into the Ameo), accept the warnings and click next, it will tell you your current ROM version and the one to upload, hit next and so on, finally click on update, after a while the status screen on the PC screen will also appear on your Ameo.
- wait until it is done and the Ameo has rebooted and installed
- restart the Athena unlocker and repeat steps 1 to 3
No matter what you do: NEVER disconnect the device from the PC during upload!
Hey will, Just done that, all went well, 100% upload, screen went black, comp says no connection, now I have a red light round the joystick and cannot turn on or get to bootloader!!!!!!!!!!!!!!!
Any ideas?
Have you updated the T-Mobile-ROM? Did you press the camera-button AND reset button? The Olinex-bootloader screen should appear.
Updated the rom, then it went blank and the red light appeared, now I cannot get the bootloader screen up
wait a minute!!!!!!!!!!!!
SHE LIVES!!!!!!!!!!
Am i right in thinking I now need to do all 3 steps in the unlocker again?
I forgot to tell you the most import rule: Dont panic!
Yes, repeat steps 1-3 from the Unlocker, start with step 1, I will wait for you.
JUST a second: Your device is showing Olinex v1.20 when in bootloader mode AND/OR your 6.0 ROM is starting now, correct??
Cheers Will, The battery is as flat as a fart at the mo, so gonna leave it till the morning. Thanks for your help and I'll post here tomorrow to let you know how I go.
Thanks agin, you're a life saver!
Phil
Glad your Ameo didn't break.
Loading the battery to 90+% is essential as it might break your device during upload.
Remember: after each ROM update (Radio update also etc.) the device will perform a hard-reset, so you have to wait each time until your Ameo has finished installation and has resynced with your PC.
IF AND ONLY IF the ROM itself has been loaded without problems and your Ameo has synced with your PC, then
- proceed with Athena unlocker, repeat step1 => wait for full installation and resync (don't close Athena unlocker) => hit finish-button on PC
- do step 2 (update), then WAIT for reset, full installation, and resync BEFORE proceeding on the PC because
- as for step2 the unlock-program will be copied and started onto the Ameo itself (that is why you have to wait)
- hit OK on the PC (the screen will inform you about the unlock process on the PDA, hit ok if the device is synced and ready), on the PDA you have to accept the installation of the program, hit install?/yes? there and unlock BOTH SIM and CID (=ROM unlocker), so you can use any phone-provider and any unofficial ROM
- finish the installation on your Ameo (hit unlock and afterwards OK etc. somewhere on the screen, I can't remember if it will hard reset again), then
- do step 3 on the PC, the same upload and hard reset and waiting procedure as before.
Done! Now you should be able to use any SIM-card and update any unofficial ROM (v1.2 versions ONLY for the moment, BEWARE!).
Hope this helps for the start.
Sorry I lost track on you pthechemist but will seems to be doing a great job here, as long as you have spl1.20 already installed and follow the procedure, you are pretty safe although it can be a bit scary.
Good luck
Cheers for the help and support guys.
All is now running PERFECTLY!
Just in the process of finding some decent games to put on and get tomtom setup
Oh, while I think about it...
The guy who I bought the phone from had a customized home screen which I cannot seem to replicate, any chance it was a downloaded theme? if so, any recommendations?
Good work!
Ad TomTom: lookout for post#1 in this thread, the settings there did definately work with my TomTom7.
Ad skin (remember: 1.2 only with Olinex v1.20): I've been using MichyPrima's R5.1 for a while now, there is the big HTC home screen (black_vga) with this big watch (aka x7510). Another one is the Diamond skin. Just look around, there are multiple skins for tryout.
Hey Will,
Thanks for the info, will have a look around for skins
Hey Will,
Thanks for the info, will have a look around for skins
Hi. I have searched the forums, but haven't found the answer I have been looking for, so sorry if this is a repeat.
I am working under Windows 7, installed VMWare and XP Pro on it, and easily installed Hard-SPL and Cracings 6.5. When I went to upgrade the Radio, I was sure to download one without SPL and IPL. I tried to upgrade, but it hung at 2% for at least 5 hours. (I knew it was bad in 2 minutes actually, but decided to wait). Now it will turn on, but to the tri-color boot screen. Tried hard reset (although I didn't really expect it to work). Is there anything that I can do? It shows when I connect it to usb, both on the phone and on the computer.
It is FAR out from under warranty, so thats out, but if there is anything I could try, I would be much obliged for pointers. Thanks a lot!
-Jotek
You need to make the update with RUU 2.5.2
( http://forum.xda-developers.com/showthread.php?t=314952 ).
Try it, if even that does not work (for me it works only with wizard_love ROM
( http://forum.xda-developers.com/show...293480&page=21 loca's post), but not with other cooked ROM's) then you can try WST wizard service tool
( http://forum.xda-developers.com/showthread.php?t=329170 ) to unpack the nbf and load only the OS ROM.
Thanks for the info.
I will try it later this weekend when i get time! (moving to new apt.... sigh... can't feed the addiction)
-jotek
If Tri Colour Screen WST needs to boot into WM OS surely???
How can you use WST if only on bootloader. Please explain as I have similar issues...
Dilbert
I had exactly the same experience as you: Hard-SPL followed by Cracing and then the tri-color screen. This thread helped me revive my G4.
http://forum.xda-developers.com/showthread.php?t=442126
Hey I am having the same problem but with my G3 att 8125. I flashed to 2.26 which I always do before installing any rom then installed X2A Haseebs Iphone Killer and it stalled at 57% for over an hour so I unplugged it and hard-reset it. I have installed this rom about twice and it works fine. Now my phone starts up and goes straight to the Tri-colored bootscreen. When I plug the phone in it displays that it is connected via USB but the computer doesnt recognize it. IPL 2.26, SPL 2.26 as displayed on the screen. PLEASE HELP!
Hi all, I've got the exact same problem as Quadzilla has - any help would be much appreciated!