Related
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe
Can anyone please post a guide on how to flash Hard-SPL onto my HTC TYTN.
The guide for installing Hard-SPL onto the HERMES is not available anymore, and i am EXTREMELY confused about what im doing, and i am afraid i will brick my phone if i do something wrong.
Please please please help!
Read the sticky, first post on this page.
It really isn't hard to do. But be sure you know what you are doing btw. SO read the sticky!
Basically you just download the flavor of Hard SPL you want (I used 2.10 which I can recommend, very easy to downgrade to factory SPL again as I just learned!).
After download unzip the folder and run the RUUWrapper. Follow instructions exactly, do nout unplug your device etc. and it should work like a charm. It takes about 1 minute!
If you don't know what you are doing or you are still doubting, wait for Mr Vanx site to come online again or don't flash. There is always a risk you screw up and end with a $500 brick.
So use at your own risk!
Download hard spl v7 from
http://forum.xda-developers.com/showthread.php?t=296722
thanks guys i did it
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
puca said:
hi guys have tried to update mine today on a jasjam it connects sys it updating but starts at 0% then just jumps to 100% and says flash finished but when i restart the phone it still has the same loader what am i doing wrong i want to update it from windows 5 to windows 6 using crc-9 but don't want to update till i do the loader any help from you guys would be great
cheers puca
Click to expand...
Click to collapse
start the device in bootloader, what is displayed?
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Rockford_622 said:
Mine is doing the exact same thing. Starts at 0% and jumps to 100% and says it is done, but it has done nothing.
Click to expand...
Click to collapse
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
hi mrvanx
thanks for your reply after checking the bootloader it has changed to 2.10 olie it did it so fast i thought it had failed will check properly next time and have successfully flashed it to crc 9 and it runs great thanks for all the help
mrvanx said:
the SPL flash is VERY quick.
I'll ask YOU this aswell, put your device into bootloader mode and tell us what it says.
Click to expand...
Click to collapse
I appreciate your reply Mr. Vanx. Same as with puca, I put my phone into the bootloader mode and it does indeed show the correct 2.10 Olipro version. This is the 3rd 8525 I have had and I could have SWORN it took much longer on the first 2. Even the update from WM5 to WM6 seemed to take much less time with this particular phone. Guess I shouldn't really complain
Downgrade Error 260
Hi Mr Vanx I have followed your guide to downgrade my current SSPL (2.10 Olipro) to SSPL (1.11). But I keep getting error 260. I have followed guide step by step.
I have even tried flashing from SD-Card (by renaming to HERMING.nbh). Process runs successfully, but nothing happens.
Its still showing SSPL-2.10 Olipro in bootloader. Am I missing anything?
Thanks
can some one point me to the guide. I am facing a NO GSM problem on vodafone VPA 1605 with following config:
ROM Version: 1.20.161.6
Radio: 1.03.06.00
CID: VODAP001
Bootloader: 1.04
I do not see the radio version or the IMEI. So I would like to do a HARDSPLv7 followed by Radio ROM update to 1.06.00.10. I hope this will work. Seniors may help with their sggestion.
Can someone help me with the guide to HARDSPL as I am doing it for the first time and the guides are not available at MR Vanx site nor can I locate the sticky?
regards,
H
have you read the first page?
cant uprade from spl 1.40 to 2.04
am using hermes 300 and i want to uprade from 1.40 t o 2.40 but i cant do it.i ve tried can anyone help
dania
How to hard reset without win
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
majida said:
hi
I have an I-mate 9502 but my problem is for pocket pc generaly.
I installed a program for sound, When I do a soft reset it hangs on Blue Imate page and didn't boot.
I tried to hard reset but it dosen't worked too(I know hard reset of it, is Green+FN+Power button) but it don't work, Also I tried to install a fresh Rom but it need to loud windows.
Please help how to hard reset it.
thanks
Click to expand...
Click to collapse
you should try the hard reset iMate 9502 posts by martin_yo in http://forum.xda-developers.com/showthread.php?t=407336&page=2
Code:
After Flashed with the new ROM, My Device is now stuck in iMate Blue Screen Logo....!!!
But Don't worry Guys...it can be solved with manually hard Reset...
1. Remove battery and reinsert (to make sure the phone is off).
2. Hold down Fn and the Green button (with the phone icon on it) and press the power button.
3. You will see the white hard reset option screen almost immediately. Press the Left Soft Key to hard reset.
Work for me...
but !!
With many thanks Hakim
But I know hard reset of my phone, I did it many time before, unfortunately it dosen't work this time. I tried all I knew about hard reset. but I couldn't do anything for my phone.
I tried (FN+Green+power like last time I did hard reset easy)(FN+Green+reset button)It don't sho any reaction.
Please help me.
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Update - I just tried this:
http://forum.xda-developers.com/showthread.php?t=326953
but without success. I get an Error [260] and the entire process stops.
Anubis1965 said:
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showthread.php?t=405814
lakeman said:
look here
http://forum.xda-developers.com/showthread.php?t=405814
Click to expand...
Click to collapse
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Anubis1965 said:
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Click to expand...
Click to collapse
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
If you see in bootloader mode ID showing somenting different than ATHE100 the solution is HERE http://forum.xda-developers.com/showthread.php?t=405814
I had the same problem! whell restart your pc and then connect the device to it. now start flashin an spl 1.20 rom. i did it and it worked! I hope i works for you too.
Cheers, Hirad
lakeman said:
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
Click to expand...
Click to collapse
Thanks - already tried!
When I reset/hard-reset the phone (tried many ways) I see a garbled boot image (with random pixels here and there)... It is definitively not the usual bootloader with the information about the various ROM components and the "USB" text at the bottom.
Anubis
Solution!
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
You are right and this is what sergiopi and I were referring to , specifically this post
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
We were refering to the whole thread so you could learn the background.
However you are incorrect in your advice about how to enter bootloader
All you need to do is hold in the camera button and reset
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
Thanks - you are giving me some hope! I am on a business trip now and my Athena is at home, but I will try that as soon as I am back
Anubis
Hi,
i flashed a rom 2 weeks ago, everything went well. yesterday i wanted to flash another os but before i could flash it, it seemed to get bricked. It stucks on the "HTC Splash" (not the WM6 Splash). I read a lot of threads and wiki threads but i don't unterstand anything! What i've to do to unbrick my phone? I tried to flash another rom but after 0% of flashing a error appears.... flashing with sd card doesn't work, too it changes to bootloader after the "Loading..." screen
i havent got hardspl or something...
please help!
UPDATE: i got the sd flashing to work... same thing but: now it stucks at the WM splash, not the t-mobile/htc one...
You need to find out what SPL you have (I'm guessing 2.03 but if you have 2.10 olipro then its got Hard SPl on it) and then do a search for "bricked SPL x.xx". You will probably find a HEAP of posts. However, some advice that seems to recover a small minority (sometimes with the "No GSM" error) -
1st thing to do is do a hard reset. Both softkeys and reset with stylus. Hold in all buttons until it asks if you want to reset to factory. Press "R" on the slideout keyboard and the "Space".
Hopefully this will fix. If it doesn't, Put it in bootloader, connect to pc (make sure "Allow USB Connection" Active Sync settings have been unticked) and run the SHIPPED STOCK ROM. This is the rom the Hermes came with originally. This MAY fix it otherwise you're in for some major reading and hair pulling.
If you should fix this then PLEASE, for the love of god, Hard SPL your Hermes before going into the wide world of flashing.....
Good Luck...
thanks i'll try it. hard reset causes kinda... nothing^^
i hope i can fix it otherwise i'll buy a touch pro
...but i think it doesn't work, because i flashed a shipped rom via sd card yesterday and the problem is still there... isn't there any way to put hard spl on my device, yet?
Try re-installing the stock rom again using sd card (if thatys how you did it last time), it could've been a bad flash. I've had those a couple of times myself. Just remember to install Hard SPL if you're successful as it makes it SOOOO much easier to recover from bad flashes.
Last thing to check would be if you have "bad blocks" using MTTY. If the boot sector has been stuffed up this may cause this problem. Do a search through the wiki, its been covered extensively...
Cheers...
okay i think my problem is solved: t-mobile replaced my device
first thing i'll do with my new device: HardSPL^^
anyhow thanks!
Upgrade successful but now stuck
I have a Three (au) Dopod 838 pro, which I upgraded from the original Windows Mobile 5 to the Three Windows Mobile 6.0 ROM. Unfortunately I didn't read up on this site first, I thought it would be straightforward since it was a ROM from the manufacturer and all, so I haven't Hard SSPL.
The upgrade reported as successful and my PC disconnected but the phone won't boot, it sticks at the Dopod screen with some numbers at the bottom. They are:
M 05 R 1.47.30.10
S 04 G 32.80.7020.20H
B 07 D 3.54
I have tried hard resetting, and returning the phone to bootloader and reflashing the same new ROM image, always with the same result.
On the bootloader, it says
HERM100
IPL-1.04
HERM100
SPL-2.03
Is there anything which can be done or is it a trip to the service centre (wherever that is)?
Just checking - Hard reset = both soft keys above the dialler closest to the lcd and reset with stylus. Hold in until it asks if you want to reset to factory. Press r on slideout keyboard then space.
This is a hard reset, not just using the stylus.
Otherwise, you have a LOT of reading material to go through with (maybe) no actual solution.
Cheers...
tried that
Thanks, but yes, I had tried that, a number of times. I think the phone will be going to a service centre today.
Dear Members,
I tried to upgrade my JasJam with "838Pro_HK_ENG_WM6_Upgrade_20070712"
Which worked with other JasJams (Many of my friends has it working).
On upgrading, it stucked on 11% saying Error [262]
I went through recovery, and it said remove the USB cable, remove the Battry, Return it, start the phone, connect the USB, and its recovered.
After that Its again stucked in 100% and the same senario is happening.
Please tell me is there any possibility to restore my phone working.
Its stuck now, and only the (Three color screen) is on the screen.
Hard reset, soft reset is not functioning, and the phone refused to show anything except the three color screen.
I searched the forum, but found no relative article, I am searching since two days your forum and I know that no other forums can help me in this as I was always getting my help from yours.
Thanks for your time.
HERM100
IPL-1.04
HERM100
SPL-1. 40. 0lopro
If you're using XP then untick "Allow USB Connection" in activesync.
Reset to bootloader on your Hermes, Hold power, OK button above flywheel and reset with stylus.You will get the same screen you have now but it won't be a f*&%ed up version of bootloader. Connect to PC by USB and Install Hard SPL V7, found here - http://forum.xda-developers.com/showthread.php?t=296722
After this, use the sd card method to install the ROM.
1. Format a 2Gb or less sd card FAT32. ?CFopy the .nbh file of the rom you want to it and rename to hermimg.nbh .
2. Insert into phone and reset to bootloader.
3 If you did everything right then follow the prompts...
Cheers...
Again problem!
Dear ultramag69,
Thank you for your fast reply.
I did (untick) that option in the ActiveSync.
And also did reset to the device by holding the Power + Ok (under the flywheel) with Stylus reset.
After that I downloaded "Hard SPL V7" and tried to update.
First of all, in the "Hard SPL V7" there was only the last option active, and there was down a checkbox also active, but when choosing the last option, checkbox bocomes like everything else disabled.
However, I got the erro 286
I felt like the Device disconnected from USB and reconnected again (Windows gave me the sound when you remove some USB device and you re-connect it again) :-|
I don't know what to do with this dead device now !
Thank you very very much for your time and help
Don't quote me on this as I suspect you need Hard SPL V7 but, as yo've tried things out and you're about to quit anyway, Try using the sd card to update the Stock rom, the rom that came on your Hermes, or updated version. It might let you do it if the CID matches.
I don't believe SPL 1.40 allowed you to flash ANY rom but it may let you re-install the stock rom BUT it must be the original carrier software it came with. If you had Telstra rom on it when you got it, it must be a telstra rom you flash. Make sure its for the right country too as some carriers are all over the world.
Cheers...
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
Hello ultramag69,
Thanks alot for your reply.
Having my i-mate dead, is really interesting.
I am trying to recover it up, Mine came with (HTC) logo when booting, and I did flushed it with Dopod.
But recently, the network stopped, and I asked some experts, they said it need new OS (They ment to re-flush the ROM).
I tried with the same Dopod that was successful before, and its now stucked on 11%.
I even downloaded the Telstra but the same, it stucked on 13%.
This is my entire story, and still I am trying to get it up.
Thanks alot for your helping. nice of you.
And for all who read my post, if they had such experience before, please help.
If you can, try to find the original SHIPPED STOCK ROM. It may be your Hermes won't be recoverable as the flash stopped in the radio rom part. Most people use a cooked rom as this has the radio rom part out.
I personally use the sd card method to flash my roms so there are no sync errors or accidents with my PC. But you need Hard SPL V7 installed to get that to work with any but the shipped rom.
DON'T try flashing anything but the shipped rom or you will loose all chances of recovering your Hermes.
The only other suggestion would be to flash the SHIPPED RADIO ROM, but you need to know what radio it was before you flashed it with the dopod rom.
Unfortunately the radio rom is the Achilles heel of our phone series. Any problems during flashing of that means we pretty much end up with a brick 99% of the time. Most people are stuck and the rest seem to have limited success reflashing the radio. AVERY small percentage get it working with no trouble, but its a REALLY small amount of people.
Good luck, Make sure you flash with the SHIPPED STOCK ROM to improve your chances of success.
Cheers...
Ultramag69, Thanks alot for your consideration.
Flusching using SD card didn't success with SPL V7.
I formatted my MicroSD card, 2GB with Fat32 FS.
After that I copied the file that came with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate, and holded the (Power + OK under flyweel) then restarted using the stylus, It showed me the tri-color screen, then it shows (Loading...) with Gray background screen (Which is normally the flusching screen) but it returned to the tri-color screen.
Any suggestions to get this SPL V7 installed successfully ?
I tried with all my (.nbh) files that I have downloaded from all sources, but its the same screen.
I think something is really wrong with me i-mate, should I take it to some Hard-ware service center ? and what can be damaged and need to be replaced in such cases ?
I am very excited in getting it working again.
Thanks alot.
Cheers...
I had bricked my Hermes a couple o' times, because of a rom I cooked half-way ( LOL ). Each time I had to flash back to the stock rom as suggested. Don't lose hope, cuz there's some people who will tell you just to accept it as bricked. You could also take the sucker apart and use jtags to flash. Most types of bricks can be solved when it comes to the Hermes. There's a thread somewhere that polled the different types of bricks, and except for radio bricks, most can be solved. If you unbrick it try 6.5 .... !!! My rom is cooked all the way now
Arwany, did you run the SSPL.exe file in the sd card instructions for Hard SPL found on page 116, post 1160 of the Hard SPL thread? You need a version of Soft SPL (SSPL) to flash using the sd card as the CID must be bypassed. The reason we Hard SPL our Hermes is because its safer. Its worthwhile flashing the SPL using unsafe SSPL (even if you use the pc you have Soft SPL installed) as its a short flash, flashing a rom (especially stock roms with the radio rom inside) is a riskier and longer flash.
Cheers...
I had the same problem.. All you have to do is establish a connection with Actisync, then run the Updater. There will be 3 colors on your Screen, sont worry, just wait 10-15 min and your should be done with the setup.
Want to help
Arwany said:
Ultramag69, Thanks alot for your consideration.
Flusching using SD card........ with the zip archive (RUU_signed.nbh) and renamed as required: (herming.nbh).
And I put it in my i-mate..........
Click to expand...
Click to collapse
Hi,Just to tell You that I've noticed a little spelling mistake.You've written "herming.nbh" But it should be "Hermimg.nbh".
Not the 1st person to make that mistake, and probably won't be the last.....
Hi All,
Yeah, that worked out for me, I could successfully flush my JasJam with that.
Thanks for your reply.
I am still facing problem when trying to flush with other OS, its always stuck on the GSM line.
I am using the SD flush method.
Any suggestions ?
THank s alot for your help!
If you have the no GSM problem the only way to, maybe, fix is to flash the original SHIPPED STOCK ROM, or the original radio rom. Flashing anything else may result in a permanent brick...
If it doesn't succeed then, sorry, its not repairable. Can be used as a PDA but not as a phone ever again.
Cheers...
Thansks Ultramag69, for all the helps, It solved my main problem.
You also Ekonkar, your comments was so helpful.
I will try to do some hardware repairing in some Mobile shop, they may get it up again !
To fix it will cost more than to get a new device... They'll tell you they can't fix it or it needs a new mainboard. Will still cost you for this nugget of info. My advice, buy a Hermes off ebay, either working or not. If its not, make sure its screen related problem cos you have the parts to fix... Unless your screen has gone bung too...
Cheers...
I gave it to the repairing guy, he replaced the GSM item and its up and running now for only 20$.
Prost :-D
Sweet, You should post where and what country so others in the same situation might be able to get their Hermes up & running.