charging with wifi in negative direction - JAMin, XDA Neo, S200 ROM Development

my phone seems to charge in negative direction (discharge)while wifi is switched on ,i use 5v 2amp local charger.,another observation i made is while putting it to usb charging of a desktop it charges properly while even with wifi being ON ,my rom is Prophet_S4V.19701.01_Clean, i wanna know if you have orginal imate jamin or o2neo prophet charger what does its volts and amp say it should be like 5 volt 2 amp or 5v 2A ,
although here charger does seems to be the culprit but does your battery disacharge while charger being plugged in and wifi is being used and power set to always ON ,because desktop power is like 5V 500MA.
if your phone discharges too while charger being plugged in and wifi being used with skype or youtube that would means battery drivers problem plz check when you find a chance.

Related

Maximum charger amperage?

Alright, so I have a mini USB car charger that is rated at 2.0A (got with GPS) and I just want to make sure the extra amperage is not going to charge my battery too quickly and then kill it in the process. All I have to go on is that my wall charger is capable of only 1.0A and the computer USB is on the level of mA. Does anybody have a car charger or know the maximum amperage possible that these phones can take?
Thanks in advance.
Its to Strong ! I have Crash a PDA with 1.5A
I've used a 2.0a charger but noticed that the battery didn't charge right.
On that note, also noticed that a .5a or 500mA charger after about 6 months killed my battery. (burned out and won't take a full charge anymore)
Recommendation is to stick to 1.0A charging as much as possible as the Wizard's charge circuit is designed at 1.0A charging and monitoring.
DOESN'T MATTER ..if u know the basic Ohms Law..its the max capacity of the charger.(or any source) the current regulating circuits will take care of the real charging current fed to the battery
I charge my phone on my computers USB connection all the time, all computers have a maximum of 500mA USB current.
Amps are pulled from the charger, not pushed to the phone.
Voltages are pushed to the phone, not pulled from the charger.
If the phone draws too much current from the charger, the voltage drops to a point where the maximum power (P (Watt) = U (Voltage) * I (Amps)) of the charger isn't exceeded.
According to the USB specification you need at least 200mA with 500mA recommended +5VDC.
More is never a problem, you could even use a 50A power supply without breaking your phone. Practically spoken: I wouldn't do that.
huh?
I have messed up a few devices before by putting the wrong charger on the device (2.0 amp charger on a droid eris and 1amp charger on the MOTOACTV) Is this a problem with the device's charging circuit? In general it should only pull up what it needs to charge but my devices were messed up?
I returned the first MOTOACTV after it wouldn't leave the boot screen and the second one I got acted funny on 1 amps as well. It charged fine on .75amp charger that came with the device but when I put it on my HTC Dinc charger it shot up from 10% to 20 to 30 etc. all within minutes. Hope I didn't mess this one up too.
Just trying to figure out what the deal is. My phone for sure charges faster when connected to 1amp vs .5amp (computer). This makes sense I understand because the device is able to handle 1amp, but I wonder if it would mess up with a 2amp charger.
Thanks!
The last two posts of 2008 are correct. Your phone is capable of drawing more than 500 mA but less than 1000 mA. If the charger is 1A, 1.5A, 2A, or 50A, it won't make a difference to the phone's charging time or life.
Wrong voltage can be bad, but phones are designed to support USB charging, as a minimum, and 1A to 2A is always safe. As was said in 2008, the charger pushes voltage to the battery, but the battery pulls current from the charger.
That's a really good way of describing it
Pushing and pulling current and voltage is a really good way of describing it.. Given that I am theoretically well within the charging parameters, how comes my phone (Galaxy mini/pop) becomes unusable when its charging (touch screen doesnt touch and screen jumps to new screen without touching?) Am I wrecking my phone?
No, your charger is to blame. Maybe it isn't properly grounded. Phones with capacitive touch screens (not the Wizard! but maybe your phone) can get really weird on some chargers. I have a Nexus One with an aftermarket charger that always makes the touch screen go haywire. When I use an HTC charger, the phone has no problem. As far as I know, the damage isn't permanent, it's just that the sensors get confused. When I disconnect from the charger, turn the phone off, then turn it on, all is well.
My wizards were never bothered by chargers, no matter what kind, as long as they were mini-USB, they were the right voltage. The wizard doesn't take as much current as more modern phones, either.
Hmm. Not properly grounded sounds very plausible. Viva mediterranean circuits. Thanks
Usb chargers will be rated at 5v, which is exactly the correct voltage to charge your device. What you want to make sure is you buy the correct "rated" amperage. Not because it will damage your phone. Amperage only exists as a sum of the power used by the device. You want to find a decent 1amp (1000mA) or higher if you wish, rated usb charger. The the mains charger for your phone is only rated at 1amp, so a 1amp charger is adequate. Avoid 500ma chargers as it will take twice as long to charge and gps / satnav applications will drain the battery even when charging at that rate.
Also if you have a new pc, most of the decent boards will specify 1amp charge even when off if it has on/off charge stated on manufacture details.
Newer phones will charge fine with higher amperage
The myth that charging your device at a faster rate will reduce the life of your device’s battery is false!
If you want quicker charging, look for a wall or car charger that delivers 2100 mA of current at 5 volts higher won't matter.... These lithium ion batteries can handle it... It was just back then if you were to try to put a faster charger in an older battery it (in any cases) just won't charge.

USB car charger

Hey guys,
I was wondering if these USB car chargers are compatible for the TP2?
http://cgi.ebay.com/Dual-2-Ports-US...Accessories?hash=item518f99b7a9#ht_3242wt_958
and
http://cgi.ebay.com/DC-Car-Cigarett...wItemQQptZPDA_Accessories?hash=item3a567814a2
and
http://cgi.ebay.com/Silver-Mini-Uni...Accessories?hash=item414bbc871c#ht_2000wt_958
I'm asking because I remember in the past I used a HTC charger to charge the O2 XDA Flame and it charged. However, the phone started acting VERY weird and freeze a lot. I ended up having to hard reset it
Thanks!
I think any USB charger for electronic gaget that has a output of 5.0 v should work. It does not matter if it is an AC charger or and car lighter charger. I got one of these AC and another car lighter charger. There are all 5.0 v output. I use them to charge Ipod and phones.
chompx2 said:
I think any USB charger for electronic gaget that has a output of 5.0 v should work. It does not matter if it is an AC charger or and car lighter charger. I got one of these AC and another car lighter charger. There are all 5.0 v output. I use them to charge Ipod and phones.
Click to expand...
Click to collapse
Thank you
It's best to choose one that can supply enough current (I think the wall charger supplies 2A, but 1A should be ok). Some devices will still trickle charge with a lower current, but others just won't trigger the charging circuits at all.
I had a cheap car charger that seemed to work ok most of the time, but it got worryingly hot after a while.
My TP2 came with an official HTC charger, so I use that now and it's great.
I have noticed that if the phone is OFF then 1A is not enough and usually stops charging but if the phone is ON it completes the charge..but takes for ever.
Has anyone experienced the charging overheat situation where the led flashes orange and green? I dont know if that is the situation but it only happens when I am charging in the car and the unit gets hot.
My old "OEM HTC" charger I got on ebay (the one with the blue HTC light) just stopped charging my phone after about 10-15 uses.
It lights on (charger), but my phone doesn't catch any charge lol
I got a 1A one, and unfortunately it cannot produce enough juice when running the GPS (copilot), after a while the phone shows a message telling the charge current is not enough.
The wall charger that came with the original box is 1A too, thus the problem might be with the cheap car charger.
Brando sells a 2A car adapter that should do the trick. They're out of stock right now, but it may be worth a look.
Hey!
Mine is a cheapo but does the trick. Charges the phone with satnav running, today went from 23% to full in less than 3 hours. Plus it's really tiny so I can keep my ashtray closed all the time. Using it with mini retractable cable, it all fits in the ashtray and it's handy to use.
http://cgi.ebay.co.uk/Micro-Nano-Ti...daptors_SM?hash=item5638c26773#ht_1747wt_1165
3waygeek said:
Brando sells a 2A car adapter that should do the trick. They're out of stock right now, but it may be worth a look.
Click to expand...
Click to collapse
The manual states that the output of the AC charger is 5.0 volts and 1 amp. That means the output of the DC/car charger should be the same. Using a 2 amp current might be charging the device faster but it would probably generate more heat and might shorten the battery life.
one tip, regardless of which charger you end up with, is to not leave the phone plugged in while starting the car. my understanding is that there can be be large voltage surges or fluctuations during the startup. depending on the design on the voltage converter inside the charger, some of that may be making it through to the phone.
i once had a AA NiCd battery smart charger that went wonky after using it in the car a lot, but that was with a straight-through 12V car to charger connector.
I made my own charger for using as a GPS on my motorcycles.
There is a charge select line in the plug. If the phone detects that it is connected to a USB port, the phone will not 'pull' more the 500ma. If that line is set to indicate a non USB port, then the phone will pull 1 amp. MAX (I never saw more then 900ma myself).
If you have the wrong charge plug, it may only charge at 500ma. If you have the correct plug and the charger can manage 5 amps, the phone will still only take 1 amp max.
For a while I used the phone in a waterproof box called an Aquabox. It would overheat during charging. I now only charge the phone when it is not in an enclosed hot space.
I'm still using the off-brand 'for Blackberry' car charger I got back when I had my Kaiser. Seems to be working just fine with this phone as well.

[Q] Battery Issue When Charging using Laptop & Wall Charger

Hey guys i just wanted to knw if ur phone lasts the same when charging using the laptop and using the wall charger bcoz mine is nearly 60% ie. lasts 40% less when i charge using wall charger.
Does anybody else is facing this too ??
That's an interesting observation, ill have too check. Though the laptop would be a slow charge and a cleaner regulated current due to the power regulator in the laptop's charger
Sent from my X10i using XDA App
yeah laptop charging is nearly half or less than half speed of wall charging ..
there is no difference between AC or USB power from a PC, but charging it with a PC takes a lot more time, because your USB port has not the power/current
i usually always use the wall charger it came with. But i remember that sometimes when i use any other charger it either wont even recognize the cable or not charge at all specially car chargers

2 USB car chargers, trickle charge, what gives?

OK, I read some of the threads but it seems none apply to my Atrix.
I purchased 2 USB car chargers, one has auto mA from 1A to 2A and the other is a 2.1A Kesington charger. I plugged to both. The phone says A/C charge, but it charges 10% in 40 minutes.
I used the wall chargers. Stock 850mA, it charges about 10% in 10 minutes. Iphone wall charger 1A, fast too. Blackberry 750mA, fast too.
All of them are 5v output, both car and wall.
So whats the problem? The phone doesnt like anything over 1A? what the hell is up with the phone?
I tried the Battery Monitor Widget and the readings are all over the place, but I can tell you for sure that with the wall chargers it shows A/C at over +1200, with the car chargers it shows +150 to +200, +250 at best.
I dont want to go over $100 trying stupid car chargers, so do you guys know of any limitation on the damn Atrix that decides to sip power instead of chugging.
Thanks

Charger voltage

Question about device. Does it need 18+W charger like Nintendo Switch? It's just both of them are the only mobile devices I have that doesn't (NS) or almost doesn't (SD) charge when on 5V charger.
When I correct Duo to 5V charger is its so slowly charging than when used is actually discharging...
it could be your charger or your cable. I have a 5V charger and it goes up to roughly 2amps while charging. I have a USB ammeter, tested it this morning because i thought I was having charger issues (a reboot fixed my issue)

Categories

Resources