Related
I don't know why I use HTC_Uni_SIM_Unlock_v1 with my phone !!!!
Now I can,t use IT. During the boot stops same seconds after the windowsmobile screen. It's impossible to contact it.
Read "Problem 5: Device shows NO GSM when booting" on the Common Upgrading Problems in HTC Hermes" wiki page. Solution is there for you
Maybe we should post a warning along with the Universal SIM Unlock tool instructions... such as
DON'T EVEN THINK ABOUT USING THIS WITH A HERMES!!!!!!!
There seems to be at least a couple of new victims every week!
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Thanks
domomedia5 said:
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Click to expand...
Click to collapse
Yes: SIDE OK + POWER + STYLUS RESET
I not be able to connect via USB the phone ! The radio rom 1.20.31.10 don't recognize my phone
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
is this the correct rom
thanks
Yes, this is the correct rom:
If you get a "ERROR 120: COUNTRY ID ERROR", do not disconnect the device, run MaUpgradeUt_noID again.
when I arrive to the window from ver. to ver. there are no description of the version !
what can I do
No problem, this is normal it is because the device is in bootloader mode.
how many minutes I had to wait
no more than 30min
It's stop from 30 minutes on cheching information on your device !?!?!
If the Hermes screen shows "Upgrade Radio Stack Please wait........." just wait until it finishes, if not, reset your device and put it back in bootloader mode, and run MaUpgradeUt_NoID again.
Make sure you've previously run the 'erase' commands in mtty sucessfully:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you can not success with radio upgrade, do a full rom upgrade using a rom matching your CID, start the upgrade from bootloader and make sure usb connections in activesync is disabled.
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
Ok...I have been through all the posts about upgrading etc. I still have a problem and I'm sure that I'm overlooking something....but I can't figure it out on my own. Here is what is happening (it does the same thing with every RUU that I've used...the DST fix...upgrading to WM6....etc)
1. I run the RUU and let it go through its routine (extract files, verify info on pc, etc.)
2. I check the box that says I have read the readme and click next
3. The next screen appears and it has the following steps:
Connect to the USB cable (check)
Establish an ActiveSync Connection (check)
Disable standby and hibernation on PC (check)
Make sure batter is > 50% (check)
Then I check the box and click next
4. I pick the update and click on the update button
5. I verify that I want to upgrade my phone from ROM verion x.xx.xxx to x.xx.xxx and click next
6. The program tells me that I am finally ready to update...and if I am sure I want to proceed to click next...so I click next
7. As soon as I click next...the progress bar comes up on my pc and my phone goes into standby mode (no bootloader...just standby). The progress bar never moves.
8. After a minute or two the RUU give me the ERROR [260]: Connection
9. I reboot my device and repeat steps 1-8
10. I reboot my device and my computer and repeat steps 1 - 8.
Now if I leave my device connected to the usb and close out the RUU after it gives me the ERROR [260], and then run the RUU again...when it is first verifying the information on my pc (before it asks any questions and before it tells me to connect my device) it will throw the device into bootloader mode. If I try to keep running the RUU while the device is in bootloader mode it give me the error that my device is not connected. I have tried and tried...maybe one of ya'll can help me. Thanks in advance
Chris
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
gerald_s said:
Some questions:
.) Is your desktop PC running XP or Vista?
If you have a firewall running, close it.
.) If you running Vista check this guide:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=23&Itemid=27
.) What updates did you try to flash?
.) Did you install Olipros bootloader first?
Click to expand...
Click to collapse
XP
No firewall
I tried to flash the WM6 from AT&T I assume its beta
and no did not install the Olipros bootloader
Ok...I think I found out how to do this...Ya'll can tell me if I'm screwing something up.
I go through all the steps listed above until it gets to the progress screen. When it gets there I manually put the the device in bootloader mode (Power, side ok, and reset). Once I do this...the progress bar starts moving. I will let you know if this works...
Hmmmm
Its not the way it should work but if it works its ok
You should have installed Olipros HardSPL first and then try to flash an official rom. If its working then something with your download is wrong.
What ROM is on there now?
Has the phone been CID unlocked?
Oli's CustomRUU is better, you may want to unpack the ROM and put the NBH in a folder with Oli's RUU and then do the upgrade.
BTW, gerald_s is right, you should not have to do that... what you may want to do is put the phone in Bootloader mode manually (while not connected to the PC), then plug in the USB, then start the RUU. That helps some people with 260 error.
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
You may be trying to flash a rom that includes the radio rom. What is your device? Is it possible that your device is a new x01ht with radio 1.14 and radio bootloader 0182? If yes, then you will get this error when you try to flash a rom with this method because during the flash it will be disconnected by the radio bootloader because it is not overwriteable. If you flash using the NBH file on the microSD, it will skip past radio and radio boot and just flash the other parts of the file.
mikebraeuer said:
I've got the same damn issue... it's driving me crazy. I had this occur when I flashed my Hermes100 from the stock version to Custel's. After about 15 starts and reboots it took. I'm now trying to get to Vp3G's 3.60 and it continues to give me the 260 error.
I am trying to figure out how to fomat my micro, but really hoping to find a solution over cable.
Hermes 100
IPL 1.04
SPL - 2.10 Olipro
Any suggestions?
Click to expand...
Click to collapse
If you are running windows XP, just connect the card to the computer, open MY COMPUTER, right-click the removable disk that is your microSD and then click format. Default in windows xp is to format using FAT32 filesystem which is perfect.
The thing is... if you dont know how to format a drive in Windows, should you be flashing your device yourself?
Which Solution???
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Wantoknow said:
I've got a Softbank X01HT with:
S/N: HT639
SuperCID <--- result of checking by mtty
IPL: 1.04
SPL: 2.10Olipro
GSM: 1.47.00.10
OS: 3.54.07 WWE
I tried to flash with new Schap 3.54c but the process would not be done coz ERROR 262 or ERROR 302. Fortunately, after failure of flashing, my device is still normal running. Then I tried to flash radio 1.51.00.10 but I got the same above. Once again, I have just tried to flash splash screen and I got the same result too. It mean my device can not upgrade anything !
Anybody here show me a solution that help my device to become a normal device, I mean it will be able to flash anything ROM as it would be! Don't tell me READ and READ, I had read so much . And don't tell me use MTTY again SPL1.01MFG, I think that is a final solution
Click to expand...
Click to collapse
Have you tried flashing with your microSD?
Kevbodian said:
Have you tried flashing with your microSD?
Click to expand...
Click to collapse
I forgot to tell that, I had flashed through extra memory card yet, and could be done!
But I wanna flash ROM against CustomRUU through MS Active Sync as I had used before. Can you help me
i have a problem very similar to Chris. when i check the box "yes activesync is syncronised", and then the progressbar shows up and the phone goes into standby.
i've turned standby of in powermanagement options.
my os is XP
i use active sync v4.5
and this is first time i try this.
i've read something about this bootloader, i can get there but then i cannot sync with active sync. so i kinda stuck.
have been searching the forums and this was the same problem as mine but i don't understand your solutions.
//KufrA
--Problem solved--
i did all things without activesync,
1. start phone in bootloader
2. do the install
3. wait 0% to 100%, and done.
is there a problem with active sync or why do i have to do anything with it at all?
Hi does anyone know if there are WM6 ROMs for the SPV C550 if not are there any good WM5 ones?
look topic about wm5 for hurricane, there are also links to wm6 for hurricane device
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Has anybody tried this ROM?
lazaj007 said:
hello again
here is latest, almost perfect rom for hurricane:
http://rapidshare.com/files/56833250/566.zip.html
and new SPL for this device:
http://rapidshare.com/files/56616745/spl566wm6_spfans2006.rar
Click to expand...
Click to collapse
Ideal thanks
So is the 566.zip the WM5 or WM6 rom and has it been tested?
Whats the new SPL?
hI ALL, can u tell me the mini guide how to install this rom? I did it once to my sda but I dont remember now, where is the nbfupdatetool and RUU and patched RUU..???
when I type l c:\wm6.bin it give me this:
clean up the image temp buffer at 0x8C080000 Length 0x01B00000 MTTYDownloadImageNot allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
cmd>
maybe damaged rom, or any idea?
Gang: Make sure you're CID unlocked. (Eg, when you issue "info 2", it says HTCSuperCID).
How can do that cid unlock? give me some working link to download that tool or something. thx
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
hmm, thx for guide, I believe it will work, but I have little problem : now I cant even connect to activesync so I cant do cid unlock, any idea how to fix that
lazaj007 said:
here you go
http//www.spv-developers.com/content/SPV-Services.zip
you must check "CID Tool (Alpha)" and click set CID=11111111
after this restart your phone
and short solutions about wm6 installing:
* installation is the same like typhoon
-unlock Super CID
-upgrade new SPL (Patched ruu)
-disable USB connection in ActiveSync
-switch off your phone
-press and hold camera button, and put USB cable to your phone
-next check "Y"
-when your phone will be in bootloader mode (tri color screen) run mtty
- check USB connection in this program
and write: - info 2
- format BINFS
- l c:\566.bin (localization of your rom)
after succeful installising reboot your phone and it will be end
rom is very good, baterry work better
Click to expand...
Click to collapse
Thanks for helping out!
A few questions?
1. This link "http//www.spv-developers.com/content/SPV-Services.zip" takes me to Wikipedia.
2. Where can I find the patched ruu to update the spl. It wasn't in the zip file?
Thanks in advance!
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
gangstaunitg said:
to Mr MIAGY :
1. just write that link starting with www. (without http//, or type http://)
2. in ''wm6 for c550'' topic u will find patched RUU and all needed files, they are ziped together
Click to expand...
Click to collapse
DoH! I didn't notice the missing ":"
Cheers!
Anybody have idea why I cant connect to activesync after spl upgrade ? Before spl upgrade it all goes well. Can I do something with it?
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
I did it !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THank u all, thankS
This rom is amazing, everything work perfect, and it looks beautiful,
one more time thank you. jUUHHHUUUUUUUUU
lazaj007 said:
if upgrade was complited succes then you must turn off USB connection in Active sync, then run bootloder mode and do everything with instructions.
Click to expand...
Click to collapse
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
MrMiyagi said:
Upgrade reported as success
However after reboot I see the WM6 boot screen - loverly ...
Then the Mobile Operator Splash screen ... THEN
After too long ... the phone switches itself off and I have to take the battery out to get reponse again.
Any ideas?
It's a C550 ....
Click to expand...
Click to collapse
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
MrMiyagi said:
Ok, so a report. The phone boots, goes through WM6 splash screen, then operator screen, then APPARENTLY dead black screen.
BUT I plugged in the USB cable and the screen came on! WM6 Setup screen! All good go through setup eveything looks GREAT!
Only problem is, if I leave the phone alone for a bout a minute, the screen goes black AGAIN. Then no amount of key pressing on the device will bring it back to life.
Plugging the USB cable in brings it instantly back to life! But This means I can't wander too far from my PC ;-)
ANY Ideas
BTW IT LOOKS FANTASTIC! If I can just get around this issue ;-)
Click to expand...
Click to collapse
Heh heh ... seems I'm posting to myself ... that's cool I like my own company ... So I reflashed the SPL and some of the problems have gone away.
Phone will boot OK now ... but it will still "go to blank screen" and require plugging into the USB cable to "wake it up"
I'm out of ideas now ...
Ive got a "bricked" S200 G4 (I think)
Text in rainbow screen is
"ILP 2.20.0001
SLP 2.10.0001"
I dont know if the difference here matters.
Tried to upgrade with different ROMs, but no luck, upgrade stops in the process, different % every time.
But the latest Speedking 2 ROM I managed to install. Hopefully I softbooted and got the same rainbow screen.
Any advice?
Why didn't you hardspl your prophet ??
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
hpn said:
I did, but maybe wrong hardSPL? It is a jungle here, hard to find the right info I need because its so much.
Click to expand...
Click to collapse
1. not 100% of our Prophet can be hardspl done ( like mine )
2. if so, just go straight ahean with my lazt_tool, too easy though....
3. hardspl is just a flashing process but only spend a couple of minutes unlike rom flashing, (from 5 - 10 minute.)
all you have to read in the sticky post on the top pf this forum
I recommend youto read post 1 of this thread....
http://forum.xda-developers.com/showthread.php?t=353547 as follow....
20080601added:
[size=+2]Lazy_Tool (thks YOUZII) is for flashing all nk.nbf, in win-xp PCs, ........[/size]
WANNA GO OLDER ROMS? READ THIS POST THOROUGHLY ^_^ )
P.S. You can just change / replace the nk.nbf inside the Lazy_Tool folder if you wish to flash other roms....
20080529 added:
Cloudyfa's 19213 clean rom + Lazy_Tool, simple, fast, error free, a new upgrade tool.
[size=+3] Additional RECOVERY steps for 3 colors screen boot-up after flashing...[/size]
a. Force Bootloader Mode MANUALLY (see below Point 4 for How To ), Then flash PVtemp or NVID for prophet( P.S. the boot up screen will be changed to Qtek...),
b. ( Optional) Use Lazy_Tool to upgrade to WM6.1 (default rom is Cloudyfa's 19213-clean, you may change if you want...)....^_^,
Click to expand...
Click to collapse
20080423 added: Alternative "Lazy_Tool"
some hints ~~
if error persists while upgrading with this tool,
Please ask yourself...
I. did I softreset yet? did I make the Prophet recovery? (remove battery and sim card),
II. will the USB port of my PC currently too heavy loaded?
III. did I restart my PC yet?
IV. any connection related software other than activesync is running?
V. did I try the rear panel USB ports?
V.I is my PC currently too busy?
VI. did I try other USB cable yet?
VII. did I try the force bootloader manually before upgrade?
VIII. Did I hardreset my prophet after new flash(if everything had done but no help~~~~ ) ^_^
**************************************
2008-02-18 added ***
NVID for prophet,
Click to expand...
Click to collapse
HARDspl
(OLD method is at the bottom of this post)
1: "DON'T PANIC",
2: 99.9999% CAN BE RECOVERED BY
DOWNGRADE TO WM5 WITH entering BOOT_LOADER MODE + flashing the PVtemp (old method step 1).
3: IF USB CONNECTION ERRORS, TRY REMOVE BATTERY FOR 1 MINUTE and try again.
4: FORCE BOOTLOADER MODE MANUALLY HOW TO = ....
4a. keep pressing the Commgr button and
4b. in the same time keep picking/sticking the bottom softreset button with stylus for one second,
4c. [size=+2][highlight] THEN ONLY ONLY RELEASE THE STYLUS[/highlight][/size] and wait for the screen
TO CHANGE to the three color screen (bootloader mode),
4d. then release all and go to step 10 below..... !!!
Click to expand...
Click to collapse
(remember to download and prepare all files you needed first, or you may have errors while in the upgrade process)
Click to expand...
Click to collapse
5. Execute the Rom Upgrade Utility (ROMUpdateUtility_NV_G3.exe ( or G4), in the
HardSPL folder that you had downloaded, all activities will only take 2-3 minutes to go and
nothing will be seen in the Prophet screen.
(P.S. if connection Error, NO PANIC, soft reset OR remove battery for half a minute and try again. )
6. after the flash completed, it will restart automatically.
7. done!! in your prophet, nothing will be changed VISIBLY EXCEPT the digits IN the reboot screen !!!!!
and while booting now YOU MUSTBE ABLE TO SEE information like: 2.G3.4PDA (FOR G3 PROPHET) or 2.G4.4PDA (FOR G4 PROPHET)
Prophet Hard SPL isn't yet completed until the SPL shows
"2.G3.4PDA" or "2.G4.4PDA". ^_^ !!!
Alternate way to Flashing / upgrading your Prophet to WM6,
a. ENTER BOOTLOADER (see how to at the upper part of this post) [size=+2]OR [/size]
b. DO THE JUMPSPL...(step 8-9 BELOW) [size=+2](you can force to bootloader mode instead of step 8 to 9)[/size]
8. copy the 3 files from the jumpspl.zip to the root directory of your Prophet and then unplug / disconnect Prophet,
9. Execute the SPL.lnk IN THE DEVICE (using the Total Commander is recommended), then you see Prophet in all bright or white screen,
10. Plug back to the USB port ( connect to rear USB panel of the computer - recommended) to the device,
11. Execute the Rom Upgrade Utility to upgrade to your chosen rom
(or put your NK.NBF to the unzipped WM6_Update_Utility folder), all activities will
only take 3-5 minutes, nothing will be seen in the Prophet screen.
12. Finally, after 100%, be patient, just wait, and Prophet will reboot automatically.
13. OF COURSE, after it auto-restart, [size=+2]better one more time HARD-RESET[/size],
ALL will be OKOKOK !!!
[size=+3]Tradition (OLD) method[/size].... (for ROM with OS.nb ),
1. Connect to PC, activesync now OK, Flash with [size=+2]PVtemp[/size] or NVID for prophet for step 1
WHEN FINISH,
2. TOUCH NOTHING, HANDS-UP !!! leave it alone, just don't touch your prophet...... ( WM5 wwe flashing now finished)
3. [size=+2]ACTIVE SYNC WILL POPS UP soon, JUST DON'T TOUCH IT (disregard it) [/size],
4. THEN RUN UPGRADE.BAT from PC to flash to WM6 (should be included in your old ROM package with OS.nb )
5. follow the on screen steps and YOU WILL GET WHAT YOU HAD EXPECTED THEN~~~~~
[size=+2]PLEASE REPLY IF YOU THINK HELPFUL ABOUT THIS MESSAGE !! ^_^ [/size]
Click to expand...
Click to collapse
I`m running Mac, with XP under Parallels. Upgrading Trinity is no problem on his config. But your reciepe include running command window. I cannot connect to the prophet from command window.
Trying to solve this somehow. Thanks for the link.