hello
I'm having a problem with my Wizard.
I was with a rom and slowed, and began to slow in bootscreen.
I spent Wizardlove no use, no use WM5 original.
my wizard is not with the spl olip.
this spl and IPL 2.22.0001
bootloader and in turn makes sound that connects, most do not connect the hardspl nor softspl, only the ruu connects.
what do I do?
Thank you
sorry for English
Which windows is running on your pc,if its Vista,there are still problems while flashing on Vista,WinXP is recommended.
Get the phone in Bootloaders and connect with pc,when small usb appears,run the RUU in the rom,only try to flash official stock rom,well you can also try to flash wizard_love rom.Hope it'll flash.Activesync doesn't work and connect in Bootloaders,so stop worrying if it doesn't connect,its not required during rom flash.hardSPL or SoftSPL also do not work in Bootloaders,it must have a working OS and connection through Activesync.Get the battery fully charged before flashing,many communication problems are due to weak battery,and take out,if any sdcard or Minisd card in the phone before flashing.
most already put the wizard love and still hangs in bootscreen
help me ;/
Download official stock rom of your carrier,get the phone in Bootloaders,Hook up the phone with pc via usb cable,check if small usb appear at the bottom of the Bootloaders ,if its there,then its establishing connection.Run the RUU in the rom,it'll start to flash,but if there's no usb present in the Bootloaders,then there's a connection problem.Either the usb cable is faulty or the mini usb port of the phone is broken.
already tried by several Ronse, original qtek, and wizard love economies do not seem to advance not always hangs at the exchange bootscreen wizard love always
Related
Hi,
I upgraded ROM on G4 Wizard CID-locked wizard from T-Mobile CZ 2.21 to Superrom 1.1. But after flash, wizard stuck in splashscreen with IPL/SPL.
I can go to bootloader, but when I tried to flash another ROM via RUU (T-Mobile CZ official, Superrom for CID-locked G4 or Novii Love), RUU said - Connection Error. Simply AS and RUU can't connect to PDA. PC identified Unknown device, when I plugged wizard to PC
I tried it on 2 PCs (1. AS4.2, 2. AS 4.5 beta2), nothing....
Any ideas ? Thanks very much
Are you doing it in the correct order? That sounds dumb i know...but i had a similar problem and found out it was because i wasnt doing it in the correct order.
You have to setup bootloader and then connect usb, if you do it the other way around you get some funny errors. Thats just what i found....it may not be of help to you.
Sorry if you know this already, just trying to help, im new too.
ROM
I know i wont be fixing your problem, but, you can be sure that after the comunication problem is solve, you can use the WizardLove rom.
I mess with my phone recently, and i got stuck at the bootloader, and that rom was the only one that worked.
Ok, thank you
Problem was found. When I tried to find driver for PPC automatically, PC found nothing, but when I manually chose driver from AS\Drivers, PC driver found
Now I can flash via RUU
i had the same problem was working till 5 am to solve it
folow the directions in this thread and it should be alive once again
http://forum.xda-developers.com/showthread.php?t=294107
Hi,
I had successfully used ShellTool to load Crossbow Reloaded v1.5 on my Xda Mini S (G4 CID-Locked)
But then I became inquisitive and I tried loading the WM6 Business Edition.
http://forum.xda-developers.com/showthread.php?t=302934
The process interrupted abruptly as the activesync connection broke (Don't know why that happened.) However I restart the device and now it is stuck on the initial blue O2 screen displaying IPL, SPL, GSM and OS information.
Now it is mentioned here
http://forum.xda-developers.com/showthread.php?t=293480
That if the device does not boot I should restart it in the bootloader (which I did), connect the usb and run RUU. But the download (Wizard_Love_2.26.10.2_WWE_Novii+CF2.rar) contains newromupdateutility_wizard_noid.exe and on running that I get the CONNECTION ERROR. I think this is happening because in bootloader, actyivesync cannot connect.
Sorry I am a novice in this... please help.
Regards.
Activesync will not connect from the bootloader. This is not a problem. Activesync is not needed to flash your phone. You just need the USB connection in the bootloader. As long as you see the letters USB in the corner you can flash.
Did you use the shelltool in the attempt to load the other WM6 rom? And if ActiveSync is required to use the shelltool then you may have to flash an official carrier rom in your current state (one that matches your CID so it will flash) and once your device boots again you should be able to use the shelltool and load the other rom that you want.
Personally this sounds like a big hassle to me and if it were me I would just pay the 25 bucks or whatever it is to get the unlocking software from the unlocker website and CID unlock my device so I could pretty much flash at will (G4 safe roms of course)
Downloaded the original rom from my-xda.com and it worked. Got the original system back.
Just updated to faria's wm6 using the same shelltool and all works fine. Looking at voip now.
thanks for the suggestion.
Cheers..
I know it sounds noob´ish and it surely is, but I just cannot flash anything onto my Hermes right now. I´ve already WM6 and SPL1.13 on it. I also tried SPL1.09ds but all I get from the RUU updater is an Error260 when I try to flash a new WM6 version onto it. I also tried unticking USB connections in ActiveSync and manually starting the bootloader on my Hermes100. Can anybody give me a tip how it can be done?
PS.: Just tried the micro SD card flashing method which used to work here but doesn´t anymore! I´m really stuck now
what is your current SPL/IPL version??
to check press and hold the side ok button and the power button, then insert the stylus into the hole in the bottom of the device.
Hamudi2000 said:
I know it sounds noob´ish and it surely is, but I just cannot flash anything onto my Hermes right now. I´ve already WM6 and SPL1.13 on it. I also tried SPL1.09ds but all I get from the RUU updater is an Error260 when I try to flash a new WM6 version onto it. I also tried unticking USB connections in ActiveSync and manually starting the bootloader on my Hermes100. Can anybody give me a tip how it can be done?
PS.: Just tried the micro SD card flashing method which used to work here but doesn´t anymore! I´m really stuck now
Click to expand...
Click to collapse
For me, I have same experience. I have tried 1.09ds and 2.10 (Hard-SLP), it alos not work for flash rom, display error[260] at final.
Do you have admin rights onyour machine? Also if you dont try with Force SSPL option. I get that error form work when I am not logged in as admin.
were are you stuck? if your stuck in bootloader or splash, look here
If you can still boot to OS, try to flash HardSplv7. if this is successfull, try to flash the new wm6, instead of using autodetect, click spl2.10, and check "is it hard spl?".
good luck!
sorry, I am not stuck on my Hermes, it´s all good, but it won´t flash anything and yes, I have admin rights on XP. I´ve got IPL 1.00, SPL 1.13.Oli. I´d really like to update to a newer version of WM6 but I can´t. I even tried with force SSPL and even the HERMimg.nbh flashing method from card didn´t work.
What I can do off course is booting into WM6, but my WM6 version is a quite old one
PS: Troubleshooting info: When I try to flash HardSPLv7, my device is going into Tricolor mode (like it should) showing IPL-SSPL by Des and SPL-1.09.ds and XP hardware assistant is searching for drivers for an unknown USB device and after a while I´ll get the error260 :/
are you up to date on your .net framework? 3.0?
framework 3.0? no, I think I have 2.0, but thanks for the tip. But my problem is now solved I formatted my micro SD to FAT32 and that helped flashing directly from card. After that I tried flashing via USB and now that also works!
I need some expert help please! I have a Hermes (Orange SPV M3100) that I want to flash with a custom ROM but I am having a problem with ActiveSync losing the USB connection at the point that the device enters the bootloader screen. I am also unable to flash using the SD card method. I have flashed a Nike without any problems and I'm usually good with technical stuff so I think there must be something extra I need to do that I have missed. I hope that somebody can spare the time to help me solve the problem. Here are the details:-
I am trying to follow Mr Vanxs guide to flashing the ROM in windows Vista so that I can upgrade it from WM5 to WM6 and apply a custom ROM to load a new TouchFlo style OS. The first step in this process is to flash HardSPL using this guide but my problem with the USB connection won't let me do that. I have unlocked the device using Hermes Unlocker 3a so it is (or should be) SIM and CID unlocked and be SuperCID with HardSPL-1.40 (so maybe I can miss the Mr Vanxs HardSPL step?).
So, when I run the RUUWrapper.exe, choosing the Force option and accepting the messages I eventually get a prompt on the device. At this stage ActiveSync is connected. I click Yes on the device and it enters the bootloader screen which shows 'USB' on the tri-color screen but ActiveSync immediately drops the USB connection. The update then waits for a while then fails with Error 260. I have to do a soft reset to get the device out of the bootloader screen. When the device reboots the Activesync connection comes back to life.
I thought that I maybe don't need to HardSPL first so I tried just going straight to the ROM upgrade but I get the same problem.
Also, I tried following this link to flash using the SD card instead of USB but when I get to step 6 I don't see a confirm message - just the usual bootloader screen (it doesn't help that the screen shot doesn't appear on the link so I'm not even sure if I'm getting the correct screen). Any ideas?
I realise that an answer to this probably already exists somewhere on the forum but I have spent hours trawling through posts and I can't find it so I hope somebody has come across this before and can help me out.
Thanks guys!
Don't worry I solved it by rebooting my PC, skipping the HardSPL and flashing with an official ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108). I can now apply custom ROMs.
Hi, sorry for capitalized title...
I searched and tested for weeks for a solution in this helpful and very professional forum... but I still haven't found a trick for my problem:
I have a NIKI100 - 20key that ActiveSync doesn't recognize (usb port still charge in Windows environment but no data transmission seems to work).
I tried many PCs with many OS, and now I can say that THIS IS NOT A SOFTWARE PROBLEM (or not?).
So i tried SD flashing, and it works only with signed ROM, so I can't flash WM 6.5
Because of USB issue, I can't flash HardSPL.
MTTY doesn't find the NIKI on COM or USB port.
The question is:
Is there a way to flash HardSPL via SD or is there a signed ROM with WM 6.5??
THANKS A LOT IN ADVANCE!!!
ROM: 2.16.831.3
Radio: 1.65.29.22
NIKI100
SPL-1.22.0000
CPLD-4
Marshalll said:
Hi, sorry for capitalized title...
I searched and tested for weeks for a solution in this helpful and very professional forum... but I still haven't found a trick for my problem:
I have a NIKI100 - 20key that ActiveSync doesn't recognize (usb port still charge in Windows environment but no data transmission seems to work).
I tried many PCs with many OS, and now I can say that THIS IS NOT A SOFTWARE PROBLEM (or not?).
So i tried SD flashing, and it works only with signed ROM, so I can't flash WM 6.5
Because of USB issue, I can't flash HardSPL.
MTTY doesn't find the NIKI on COM or USB port.
The question is:
Is there a way to flash HardSPL via SD or is there a signed ROM with WM 6.5??
THANKS A LOT IN ADVANCE!!!
ROM: 2.16.831.3
Radio: 1.65.29.22
NIKI100
SPL-1.22.0000
CPLD-4
Click to expand...
Click to collapse
Can you tell me what happens when you connect your device with your computer, when it is already in bootloadermode.
You can turn the phone in bootloadermode to turn your device off and press then on/off button and camera button on the same time, and keep them pressed until bootloader appears.
If I'm correct you will see Serial in the white block, just let me know what you see in the white block when you connect the phone with the computer, if I'm correct Serial will change in Usb, if not just let me know.
Greetz,
Tnx for reply...
I see USB when I connect the cable, Serial when I disconnect the cable.
I'm searching for a SD-card-method for flashing HardSPL: is this a good idea or I'm just wondering ?
Marshalll said:
Tnx for reply...
I see USB when I connect the cable, Serial when I disconnect the cable.
I'm searching for a SD-card-method for flashing HardSPL: is this a good idea or I'm just wondering ?
Click to expand...
Click to collapse
Ok, can you tell me if you're device has a simlock ?
Greetz,
Hi.
No simlock.
Tnx.
Marshalll said:
Hi.
No simlock.
Tnx.
Click to expand...
Click to collapse
Ok thanks, I'll do some searching and see if we can fix it.
Regards,
Ok, if I where in your situation I should try it this way, just be aware that I can not test it because I don't have such a problem, and you can brick your device if it went wrong.
1. Copy sspl-1.16-nike.exe to your sd-card
2. Copy sspl-1.16-nike.exe from your sd-card to your device
3. Turn phone off and remove sim and sd-card
4. Turn phone on and connect device to your computer
5. Run sspl-1.16-nike.exe on your phone
6. Wait until usb appears in your device
7. Unplug and replug the usb cable
8. Now flash the HardSPL 1.22
If you can run the HardSPL you should be able to flash a wm 6.5 rom.
Rataplan said:
Ok, if I where in your situation I should try it this way, just be aware that I can not test it because I don't have such a problem, and you can brick your device if it went wrong.
1. Copy sspl-1.16-nike.exe to your sd-card
2. Copy sspl-1.16-nike.exe from your sd-card to your device
3. Turn phone off and remove sim and sd-card
4. Turn phone on and connect device to your computer
5. Run sspl-1.16-nike.exe on your phone
6. Wait until usb appears in your device
7. Unplug and replug the usb cable
8. Now flash the HardSPL 1.22
If you can run the HardSPL you should be able to flash a wm 6.5 rom.
Click to expand...
Click to collapse
All right from 1. to 7. but when I run flashin it shows error code 260 (unable to connect).
Is there a way to run SPL "JUMP" and then flash HardSPL via SD card? I think it's the only way to flash HardSPL
Rataplan is the expert one on this area,
but wath is your operating system? Seven or XP?
Because i just was able to hardspl on XP, all other things I was able to do on Seven.
Marshalll said:
All right from 1. to 7. but when I run flashin it shows error code 260 (unable to connect).
Is there a way to run SPL "JUMP" and then flash HardSPL via SD card? I think it's the only way to flash HardSPL
Click to expand...
Click to collapse
Did you try to run the HardSPL 1.22 from the bootloader ?
Let me explain a little bit better, did you connect your device with your computer when your device is in bootloadermode and then run the HardSPL 1.22
If this fails, you can rename your nbh-file, hardspl-1.22-nike-shipped.nbh into nikeimg.nbh, copy nikeimg.nbh into the root of your sd-card and turn your device on while pressing the on/off button and the camerabutton on the same time and follow the instructions on the screen.
Succes,
Rataplan said:
Did you try to run the HardSPL 1.22 from the bootloader ?
Let me explain a little bit better, did you connect your device with your computer when your device is in bootloadermode and then run the HardSPL 1.22
If this fails, you can rename your nbh-file, hardspl-1.22-nike-shipped.nbh into nikeimg.nbh, copy nikeimg.nbh into the root of your sd-card and turn your device on while pressing the on/off button and the camerabutton on the same time and follow the instructions on the screen.
Succes,
Click to expand...
Click to collapse
Yes, I tried all of this method...The PC can't recognize the niki in bootloader mode.
When I put HardSPL on a tested sd-card (renamed NIKEIMG.nbh), I'm stuck in white screen with "Loading...".
I found some method for flashing HardSPL via sd-card (for Kaiser: http://forum.xda-developers.com/showthread.php?t=433835):
is there a SSPL Jump for Niki that run from sd (as with Kaiser sd-method)?
BTW, I think this is the right way... I'm trying and searching!
For Openview:
I tried with many PCs with XP Pro and 7. The niki usb port seems to be broken (only charges, but no data connection).
Nothing seems to work. If anyone has somethig for flash SSPL and HardSPL from SD, please post!!!
Any other ideas???
I think we tried everything but unfortunally the answer is that it isn't possible to flash the hardspl via sd, the only person you can ask is cmonex, she is the only one who can set this straight.
Here is her User cp but she is a very busy lady.
If you fix it, plse post it in this thread it can help others.
Goodluck buddy
Ok I'll try to contact mrs. cmonex. Of course, I'll post any solution (hope to find one... ).
Tnx for all!
SOLVED!
I solved the issue!! It was only a hardware problem with HTC ExtUSB port!!!
I cleared the pin and resoldered the port on motherboard. Then I flashed HardSPL via standard method and now I can flash anything form sd-card!!
Thanks to all.
Mr. Rataplan, now we can close this post!
Thanks!!
Great Marshalll, I'll ask Electroz to close this thread.