hi...
i hv HTC gene (HT8XX) (Old Gene)..
SPL 1.07.0000
ONBL 1.07.0000
right now i have stock WM5 Rom...
but last night i tried to flash WM6.1 fusion 9 Rom on my device..but
when i started RUU, everything was fine...but at last it showed
ERROR [300] INVALID UPDATE TOOL
history:
( previously i used same RUU to flash my phone....i was using Fusion 9.0 perfectly
but since i flashed wrong Rom so it bricked my phone....
than i gave my phone to HTC service center , they made it all right again..but they flashed stock WM5 ROM...
now i wanted to flash WM6.1 ROM but when i tried to flash than RUU showed this "ERROR [300] INVALID UPDATE TOOL" )
so....please tell me....what can i do to fix this problem ???
thanks in advance...!!! plzzz help
i think you are using wrong rom update utility...use the rom update utility that comes with the rom... and make sure that you are using the correct rom for old gene...which is your spl.
is it showing oref spl at tricolor screen then you must use jtag method......
go4thomman said:
i think you are using wrong rom update utility...use the rom update utility that comes with the rom... and make sure that you are using the correct rom for old gene...which is your spl.
Click to expand...
Click to collapse
dear.....i m using correct RUU as i used this RUU several times b4 i got my device bricked....
this problem is started after return of the phone from HTC service centre...
i hv tried almost all RUU which is available for gene..
and i also tried flashing almost 5-6 different roms...but same error all the time....i m using the same RUU which comes with ROM by default..
My SPL is 1.07.0000...
go4thomman said:
is it showing oref spl at tricolor screen then you must use jtag method......
Click to expand...
Click to collapse
i m using olipro method for hspl...
in which spl doesnt change...it just temporary unlocked for me..
it was working perfact for me...
i hv used almost every ROM available for OLD GENE..
but last time bcuz of flashing wrong ROM m device got bricked...
since than this problem started ..
go4thomman said:
is it showing oref spl at tricolor screen then you must use jtag method......
Click to expand...
Click to collapse
and..................i never got tricolor screen ....
whenever i hspl my device than phone reboots thn screen becomes white....thereafter...i used to flash ROM
everything is working well as usual upto white screen....
but at the time of flashing ROM RUU shows error....
hksin1988 said:
dear.....i m using correct RUU as i used this RUU several times b4 i got my device bricked....
this problem is started after return of the phone from HTC service centre...
i hv tried almost all RUU which is available for gene..
and i also tried flashing almost 5-6 different roms...but same error all the time....i m using the same RUU which comes with ROM by default..
My SPL is 1.07.0000...
Click to expand...
Click to collapse
Hey buddy, since you have given your ROM to HTC, they have again locked your CID, please go throught the stickey to how to flash again. Best of Luck
No Shaunak, there is something else wrong. He is saying that he tried to use the JumpSPL method. Its an alternative and temporary method to unlock CID for flashing ROM. HardSPL is different, it makes changes permanent.
Dear sksin
The phone is again bricked or you are currently using(able to boot) the wm5?
Dear hksin
Same problem i also have faced and finally i recovered it.
Please go through
1.The serial no. of the phone Is the sticker shows same S/N as before?
2.The HTC people has changed your IMEI No ?
If Yes then ,Now after comming from service centre your Gene has become the new Gene.
and you have to treate like this.
so do the gene unbricker solution by MTTY method and you may recover
All the best.Good luck!!!!
rkpatro said:
Dear sksin
The phone is again bricked or you are currently using(able to boot) the wm5?
Click to expand...
Click to collapse
dear..
I m currently Using the Phone With WM5 Stock
its not bricked and working perfactly..!!!
rkpatro said:
Dear hksin
Same problem i also have faced and finally i recovered it.
Please go through
1.The serial no. of the phone Is the sticker shows same S/N as before?
2.The HTC people has changed your IMEI No ?
If Yes then ,Now after comming from service centre your Gene has become the new Gene.
and you have to treate like this.
so do the gene unbricker solution by MTTY method and you may recover
All the best.Good luck!!!!
Click to expand...
Click to collapse
Dear rkpatro,
i hv checked IMEI no of phone ,,,its is same as previous..
and can u please tell me that how to check my phone's serial no. via phone only.
bcuz on the phone's box its serial no starts frm HT80XXX
but i found no way to check serial no frm the phone to confirm.
is ther any way ??
Remove the battery and you will be able to see the serial number. Please check the stickey by krazy. Now Old ROMs are appearing with 8xxx serial numbers!
Looking at your spl version, i could be wrong but I think yours is an old Gene
Addicted2xda said:
Remove the battery and you will be able to see the serial number. Please check the stickey by krazy. Now Old ROMs are appearing with 8xxx serial numbers!
Looking at your spl version, i could be wrong but I think yours is an old Gene
Click to expand...
Click to collapse
yeaa my phone has serial no starting form HT8XX
but it always works as old gene.
as before breaking my device , i almost flashed all the ROMs available for Old gene.
but mistakenly i flashed Krazy's Rom, cuz i thought tht my phone is also HT8XX
but later on i understood that my phone's SPL is 1.07.0000, which is for old gene..
anyhow my device became unbricked....but unable to flash the same Roms which i flashed in past...
so i m confused that wht is wrong with the device now..
i think that HTC guy has put some kinda Lock for flashing .. is that it ???
or is ther some other reason..
As dear rkpatro suggested that after returning from service center is has become new gene, but i am not satisfied with this . becuz everything is same as past time...
SPL n ONBL r also same as well as IMEI and serial no, even they flashed exact same ROM as it had previously..
so i m not getting that wht the problem is..
becuz everything is same , than y the Roms r not working..
i hv tried each Rom again which i was using in past...
but flashing ends up by error 300..
so guys,,,, please think something abt it...
ur attention to my problem is always appreciable....
thanks in advance..!!!
Yes, HTC has again cid locked your device, I think it should be better to get help from the krazy's sticky post on flashing a locked Gene.
Best of Luck
Black metal rom, p3401 can?
I'm having problems.
All the ROMS are giving p3401 error and my machine is only on screen color.
my SPL is 1.10. olip
someone can help me
rom or tell me what works?
Addicted2xda said:
Yes, HTC has again cid locked your device, I think it should be better to get help from the krazy's sticky post on flashing a locked Gene.
Best of Luck
Click to expand...
Click to collapse
Hi dear...
just wanna know.....that when i firstly flashed my device, than i used olipro's spl method
1.10-Olipro.nb
and Jump slp
that time my device was CID locked also, but i succesfully Flashed WM 6 Rom by this method/..
no error was ther..
now as u r sayin that its again CID locked.. so i followed exact same procedure as i followed for the first time....but this time i ended up with this strange error...
so....is ther any possibility of something else ???
solution ???????????????????????
Any Solution guys ??????????????????????????????????????????????????????
problem Solved...!!!
finally..............my problem has solved,,,,infact....my old gene has become new gene now....isnt it miracle...
nyways....even being onbl n spl 1.07.0000 originally....i successfully patched my device with hspl for new gene...and i installed Sumit's VanillaManila ROM ( for new gene)...
its working superb....thanks...!!!
Related
my himalya automatically rose frm dead..but it was Jus showin the splash Screen..so i decided it Flash it
i put it into the bootloader mode n started flashing
but i encountered a Error during upgrading the radio ROm
This is wat i saw in the RUULlog.log file
18:21:55 Connection with USB
18:22:29 Begin Stage 4
18:22:59 Radio Erase retry 1
18:23:29 Radio Erase retry 2
18:23:59 Radio Erase retry 3
now there is a splash screen n there it shows 'NO GSM' but i ttried flashing wit a Differnt rom but no Luck please Help me
Please help me my himalaya is dead since more than a week
you may send more info
like what rom was befoure and what rom are you trying to put in
with that i can try to help a litle bit
hope never dies just me......
Re: you may send more info
rictec said:
like what rom was befoure and what rom are you trying to put in
with that i can try to help a litle bit
hope never dies just me......
Click to expand...
Click to collapse
my himalaya was on original rom ..then i tried installing 1.66 version i also tried wm2005 but no differnce .. the radio version cudnt b eearased ..it was givin me an error as Quoted above..i guess i hve to give it to the service center only (
I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
your_suraj said:
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
Click to expand...
Click to collapse
First try to remove the battery and then put it back in and try to switch it on see if it boots into the windows...if not then follow the step given below...
Download any custom rom for OLD gene and run the rom update utility (RUU) it will be back to normal...
Note : Most importantly don't panic ...even if the phone is taking its usual time to boot up it may seem longer cos we are worried....have patience...
hay man
tell us the serial number of your device to tell you exactly what to do
is it (ht8xxx) or (ht7xxx) ?
it is very important
and for god's sake guys read the sticky threads first.
do not do anything before getting answers from other members.
Thanks guys, but I solve it already but I am not able to download any rom for my gene.
Can somebody give me another mirror apart from rapidshare and megaupload............. and which ROM is good, like with cube for my gene HTC 3400?
your_suraj said:
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
Click to expand...
Click to collapse
Its normal thing that ur device got off after hspl.exe
it seems like u hv new gene....so now u should use Oref unbricker...
u just followed step 1....
so u should move on to step 2
which is unbricking gene by oref method
http://forum.xda-developers.com/showthread.php?t=472169
read this bro n follow instructions...
Thank you once again but I have solved my problem already. Now all I need is a new rom for my old gene.
Could anyone give me alternative mirror for any rom? Rapidshare and megaupload is not working for me.
Help - Gene stuck at boot loader after upgrading ROM 6.5
ONBL 1.07.0000
SPL 1.07.olip
GSM 02.79.90
OS 1.7.0.0
This happened when i upgraded the ROM from WM 6.1 to 6.5
Kindly help me how to restore my phone
same here
same happened to my Gene. I tried upgrading ROM to 6.5. after restart, it get struck on bootloader screen. it is not even detected by activsync
my HTC3400 has been successfully unlocked and upgraded to WM6.1, cause not stable, so I upgraded the original ROM for HTC3400i with SD card,
when upgrating is almost finished, it stopped, shows "Invalid Certificate, Press any key......."
I have tried to recover it with backup ROM, and downloaded orginal WM5 ROM, and WM6.5, all not work.
I think SPL is wrong.
Now it shows like follows,
ONBL 1.19.0000
SPL 1.19.0000
when connect USB, shows USB on the left bottom.
How can I save it? Help!!!!!!
Thanks in advance.
Take it to the service center. No options left. JTAG may help but that would be too risky if you are an average user.
hehe,i would rather try to solve the problem by myself, so anybody can help me work out the problem.thanks.
tell me first which rom u try to flash ?
first i want to know what u do wrong so it better to solve it
ankit360 said:
tell me first which rom u try to flash ?
first i want to know what u do wrong so it better to solve it
Click to expand...
Click to collapse
i wish upgrade WM5.0 official ROM.thanks.
the story is complicated.
1)original is WM5.0
2)unlocked with gene_hspl.exe successfully.
3)upgrated with SD to WM6.1 successfully.
4)i downlaoded HTC3400i official ROM WM6.1, it remember the version is 6.1, i upgraded with SD, the upgrading is almost finished but stop and showed "Invalid Certificate, press any key to......"
5)whatever ROM i want to upgrade with SD or USB cable, all failed, including backup OS.nb+extrom.nb.
if try to upgrade with SD, showed "Invalid Certificate......", if try to upgrade with USB, showed only 2% or 3% then power on
6)when enter tricolor with ONBL 1.19.0000 and SPL 1.19.0000, "USB " shows on left bottom.
ok, what can you do?
sunnyhuang said:
i downlaoded HTC3400i official ROM WM6.1
Click to expand...
Click to collapse
enplane me from where u get this ?
ankit360 said:
enplane me from where u get this ?
Click to expand...
Click to collapse
i download from internet, from a chinese forum.
Heh, trying to solve it yourself ? There is no official WM 6.1 ROM for P3400i from HTC otherwise we wont be moaning here for 4-5 months and given our 40-50 nights for porting WM 6.1 to gene. What you have flashed is something wrong and that has messed up your SPL CID as well as ONBL.
Anyways, Try if you can solve it yourself or get it solved somewhere
Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started.
it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didn't work when i tried with "Olipro jumpspl" method it says the Update Utility is invalid, when i tried with "Orefkov mtty" it says can't unlock the CID or basicaly it says cant place the SPL and finally i tried the "Olipro HSPL" method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU.
I tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEWBIES ALSO PLZ HELP......!!
can you please let me know is it new gene or old gene?
ankuhadia said:
can you please let me know is it new gene or old gene?
Click to expand...
Click to collapse
yes previously before changing the motherboard it was HT8X series but was new gene now its same series but it is old gene....