New Problm......Very Critical Probably a challenge plz need BIG Help.... - P3400 ROM Development

Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started.
it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didn't work when i tried with "Olipro jumpspl" method it says the Update Utility is invalid, when i tried with "Orefkov mtty" it says can't unlock the CID or basicaly it says cant place the SPL and finally i tried the "Olipro HSPL" method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU.
I tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEWBIES ALSO PLZ HELP......!!

can you please let me know is it new gene or old gene?

ankuhadia said:
can you please let me know is it new gene or old gene?
Click to expand...
Click to collapse
yes previously before changing the motherboard it was HT8X series but was new gene now its same series but it is old gene....

Related

ERROR [300] INVALID UPDATE TOOL ??? please help

hi...
i hv HTC gene (HT8XX) (Old Gene)..
SPL 1.07.0000
ONBL 1.07.0000
right now i have stock WM5 Rom...
but last night i tried to flash WM6.1 fusion 9 Rom on my device..but
when i started RUU, everything was fine...but at last it showed
ERROR [300] INVALID UPDATE TOOL
history:
( previously i used same RUU to flash my phone....i was using Fusion 9.0 perfectly
but since i flashed wrong Rom so it bricked my phone....
than i gave my phone to HTC service center , they made it all right again..but they flashed stock WM5 ROM...
now i wanted to flash WM6.1 ROM but when i tried to flash than RUU showed this "ERROR [300] INVALID UPDATE TOOL" )
so....please tell me....what can i do to fix this problem ???
thanks in advance...!!! plzzz help
i think you are using wrong rom update utility...use the rom update utility that comes with the rom... and make sure that you are using the correct rom for old gene...which is your spl.
is it showing oref spl at tricolor screen then you must use jtag method......
go4thomman said:
i think you are using wrong rom update utility...use the rom update utility that comes with the rom... and make sure that you are using the correct rom for old gene...which is your spl.
Click to expand...
Click to collapse
dear.....i m using correct RUU as i used this RUU several times b4 i got my device bricked....
this problem is started after return of the phone from HTC service centre...
i hv tried almost all RUU which is available for gene..
and i also tried flashing almost 5-6 different roms...but same error all the time....i m using the same RUU which comes with ROM by default..
My SPL is 1.07.0000...
go4thomman said:
is it showing oref spl at tricolor screen then you must use jtag method......
Click to expand...
Click to collapse
i m using olipro method for hspl...
in which spl doesnt change...it just temporary unlocked for me..
it was working perfact for me...
i hv used almost every ROM available for OLD GENE..
but last time bcuz of flashing wrong ROM m device got bricked...
since than this problem started ..
go4thomman said:
is it showing oref spl at tricolor screen then you must use jtag method......
Click to expand...
Click to collapse
and..................i never got tricolor screen ....
whenever i hspl my device than phone reboots thn screen becomes white....thereafter...i used to flash ROM
everything is working well as usual upto white screen....
but at the time of flashing ROM RUU shows error....
hksin1988 said:
dear.....i m using correct RUU as i used this RUU several times b4 i got my device bricked....
this problem is started after return of the phone from HTC service centre...
i hv tried almost all RUU which is available for gene..
and i also tried flashing almost 5-6 different roms...but same error all the time....i m using the same RUU which comes with ROM by default..
My SPL is 1.07.0000...
Click to expand...
Click to collapse
Hey buddy, since you have given your ROM to HTC, they have again locked your CID, please go throught the stickey to how to flash again. Best of Luck
No Shaunak, there is something else wrong. He is saying that he tried to use the JumpSPL method. Its an alternative and temporary method to unlock CID for flashing ROM. HardSPL is different, it makes changes permanent.
Dear sksin
The phone is again bricked or you are currently using(able to boot) the wm5?
Dear hksin
Same problem i also have faced and finally i recovered it.
Please go through
1.The serial no. of the phone Is the sticker shows same S/N as before?
2.The HTC people has changed your IMEI No ?
If Yes then ,Now after comming from service centre your Gene has become the new Gene.
and you have to treate like this.
so do the gene unbricker solution by MTTY method and you may recover
All the best.Good luck!!!!
rkpatro said:
Dear sksin
The phone is again bricked or you are currently using(able to boot) the wm5?
Click to expand...
Click to collapse
dear..
I m currently Using the Phone With WM5 Stock
its not bricked and working perfactly..!!!
rkpatro said:
Dear hksin
Same problem i also have faced and finally i recovered it.
Please go through
1.The serial no. of the phone Is the sticker shows same S/N as before?
2.The HTC people has changed your IMEI No ?
If Yes then ,Now after comming from service centre your Gene has become the new Gene.
and you have to treate like this.
so do the gene unbricker solution by MTTY method and you may recover
All the best.Good luck!!!!
Click to expand...
Click to collapse
Dear rkpatro,
i hv checked IMEI no of phone ,,,its is same as previous..
and can u please tell me that how to check my phone's serial no. via phone only.
bcuz on the phone's box its serial no starts frm HT80XXX
but i found no way to check serial no frm the phone to confirm.
is ther any way ??
Remove the battery and you will be able to see the serial number. Please check the stickey by krazy. Now Old ROMs are appearing with 8xxx serial numbers!
Looking at your spl version, i could be wrong but I think yours is an old Gene
Addicted2xda said:
Remove the battery and you will be able to see the serial number. Please check the stickey by krazy. Now Old ROMs are appearing with 8xxx serial numbers!
Looking at your spl version, i could be wrong but I think yours is an old Gene
Click to expand...
Click to collapse
yeaa my phone has serial no starting form HT8XX
but it always works as old gene.
as before breaking my device , i almost flashed all the ROMs available for Old gene.
but mistakenly i flashed Krazy's Rom, cuz i thought tht my phone is also HT8XX
but later on i understood that my phone's SPL is 1.07.0000, which is for old gene..
anyhow my device became unbricked....but unable to flash the same Roms which i flashed in past...
so i m confused that wht is wrong with the device now..
i think that HTC guy has put some kinda Lock for flashing .. is that it ???
or is ther some other reason..
As dear rkpatro suggested that after returning from service center is has become new gene, but i am not satisfied with this . becuz everything is same as past time...
SPL n ONBL r also same as well as IMEI and serial no, even they flashed exact same ROM as it had previously..
so i m not getting that wht the problem is..
becuz everything is same , than y the Roms r not working..
i hv tried each Rom again which i was using in past...
but flashing ends up by error 300..
so guys,,,, please think something abt it...
ur attention to my problem is always appreciable....
thanks in advance..!!!
Yes, HTC has again cid locked your device, I think it should be better to get help from the krazy's sticky post on flashing a locked Gene.
Best of Luck
Black metal rom, p3401 can?
I'm having problems.
All the ROMS are giving p3401 error and my machine is only on screen color.
my SPL is 1.10. olip
someone can help me
rom or tell me what works?
Addicted2xda said:
Yes, HTC has again cid locked your device, I think it should be better to get help from the krazy's sticky post on flashing a locked Gene.
Best of Luck
Click to expand...
Click to collapse
Hi dear...
just wanna know.....that when i firstly flashed my device, than i used olipro's spl method
1.10-Olipro.nb
and Jump slp
that time my device was CID locked also, but i succesfully Flashed WM 6 Rom by this method/..
no error was ther..
now as u r sayin that its again CID locked.. so i followed exact same procedure as i followed for the first time....but this time i ended up with this strange error...
so....is ther any possibility of something else ???
solution ???????????????????????
Any Solution guys ??????????????????????????????????????????????????????
problem Solved...!!!
finally..............my problem has solved,,,,infact....my old gene has become new gene now....isnt it miracle...
nyways....even being onbl n spl 1.07.0000 originally....i successfully patched my device with hspl for new gene...and i installed Sumit's VanillaManila ROM ( for new gene)...
its working superb....thanks...!!!

Question Regarding Unbricker

I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.

Problem with SPL

Dear Senior members,
I am new user of Gene 100( New) verified from both method SPLcheck ,Olipro and Orefkow Method and found that It's new gene n udated it's SPL..
Then i update my WM6 Rom to Sumit's Pro User ROM ( WM 6.1 for both Old and New Gene).
It worked fine.
The by mistake I click the file gene_hspl.exe ( The file using for Updating SPL for Old gene).
immediatly My phone got off.
i tried a lot to switch on it .
then I push cam key with soft reset key, then my phone on in boot loader mode with SPL 1.10.olip
and
ONBL 1.17.0000
Now i am Not able to update to my SPL again.
and Phone is not working, What should i do now..?
Should i Update SPL again or anything else.
I tried to update Newer ROM ,But message come with Error(300) Please get newer Update Utility for ur phone.
Kindly Solve out my Problem
ur device is still under warranty period??
Try to unbrick again from orefkov method if it works GREAT! otherwise take ur device to service center and dont tell him about cracking and just tell him that it automatically switched off...
dont try anything without suggestions of other GENE forum members..just ask them too what to do..?
If you are getting to Bootloader with olip spl. orefkov method should work. BTW, How did your Gene work with both Old and New Gene ROMs???
AND WHY DO YOU NEED TO POST THE SAME QUERY WITHIN FOUR MINITUES?
IF YOU ARE IN SUCH A HURRY, BEST PLACE IS THE SERVICE CENTRE.
Addicted2xda said:
If you are getting to Bootloader with olip spl. orefkov method should work. BTW, How did your Gene work with both Old and New Gene ROMs???
AND WHY DO YOU NEED TO POST THE SAME QUERY WITHIN FOUR MINITUES?
IF YOU ARE IN SUCH A HURRY, BEST PLACE IS THE SERVICE CENTRE.
Click to expand...
Click to collapse
cool down addicted...he is just embarrassed....
vikas _khatri1981 said:
Dear Senior members,
I am new user of Gene 100( New) verified from both method SPLcheck ,Olipro and Orefkow Method and found that It's new gene n udated it's SPL..
Then i update my WM6 Rom to Sumit's Pro User ROM ( WM 6.1 for both Old and New Gene).
It worked fine.
The by mistake I click the file gene_hspl.exe ( The file using for Updating SPL for Old gene).
immediatly My phone got off.
i tried a lot to switch on it .
then I push cam key with soft reset key, then my phone on in boot loader mode with SPL 1.10.olip
and
ONBL 1.17.0000
Now i am Not able to update to my SPL again.
and Phone is not working, What should i do now..?
Should i Update SPL again or anything else.
I tried to update Newer ROM ,But message come with Error(300) Please get newer Update Utility for ur phone.
Kindly Solve out my Problem
Click to expand...
Click to collapse
jsut update ur spl by using spl for new gene.
this will do

New Problem Found with Gene......Real Critical Needed Help...

Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started, it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didnt work when i tried with Olipro jumpspl method it says the Update Utility is invalid, when i tried with Orefkov mtty it says cant unlock the CID or basicaly it says cant place the SPL and finally i tried the Olipro HSPL method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU i tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEW BEES ALSO PLZ HELP......!!
Now i m using the stock rom which came with gene,i added a lot applications i somehow managed to get touch control for scrolling and all everything ok.....but i miss the WM 6.5 style MENU, TASKBAR, FREE RAM and most of all the TITANIUM it was my favourite i was using Duron's WM 6.5 for new gene it was very cool...
Now i feel like crying i am addicted to WM 6.5 PLZ HELP...

New Problm.....Very critial...Need help plz HELP>>....

Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started, it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didnt work when i tried with Olipro jumpspl method it says the Update Utility is invalid, when i tried with Orefkov mtty it says cant unlock the CID or basicaly it says cant place the SPL and finally i tried the Olipro HSPL method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU i tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEW BEES ALSO PLZ HELP......!!
Now i m using the stock rom which came with gene,i added a lot applications i somehow managed to get touch control for scrolling and all everything ok.....but i miss the WM 6.5 style MENU, TASKBAR, FREE RAM and most of all the TITANIUM it was my favourite i was using Duron's WM 6.5 for new gene it was very cool...
Now i feel like crying i am addicted to WM 6.5 PLZ HELP...

Categories

Resources