Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started, it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didnt work when i tried with Olipro jumpspl method it says the Update Utility is invalid, when i tried with Orefkov mtty it says cant unlock the CID or basicaly it says cant place the SPL and finally i tried the Olipro HSPL method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU i tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEW BEES ALSO PLZ HELP......!!
Now i m using the stock rom which came with gene,i added a lot applications i somehow managed to get touch control for scrolling and all everything ok.....but i miss the WM 6.5 style MENU, TASKBAR, FREE RAM and most of all the TITANIUM it was my favourite i was using Duron's WM 6.5 for new gene it was very cool...
Now i feel like crying i am addicted to WM 6.5 PLZ HELP...
Related
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
koorosh_bsboys said:
I have a jasjam
i was upgrading it using the telstra WM6 rom.
during the upgrade it was around 15% that the upgrade utility show the error that device cannot connect.
my device is bricked now
IT is not KITL enabled
it the first splash screen it shows no gsm
it only shows the bootloader menu
IPL 1.04
SPL 2.03
i read the wiki on how to unbrick a bricked hermes but there is no sulotion
plzzzzzzzz
anyone can help me??????
Click to expand...
Click to collapse
Did you also read the wiki to see how to install hardspl to protect your device BEFORE flashing ?(here: http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=30&Itemid=27 )? Are you using Olipro hardspl?
Try to use the SDCARD method (Format a sdcard in FAT32. Copy the nbh file on it and rename it HERMIMG.NBH. Insert the card and HR : OK/POWER/Soft reset. Follow the instructions)
i tested that but didn't help
does anybody have any suggestion??
Try solution to reeboot ( sometimes helps)
1. get out SIM and SD card
get mtty http://forum.xda-developers.com/download.php?id=9864
2. Make BL mode on Hermes
2a on PC ActiveSync - coonection properties untick allow to connect by USB
3. start mtty on PC , choose USB and enter.
4. next enter.
5. type set 14 and enter
6. type task 8 and enter
OS have to boot if no go to 7
7. enter
8 type set 16 and enter
9. type task 8 and enter
Hope that will boot
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Pretty much all the info on unbricking is in this table by Pof. If this doesn't sort you out then you're have to send it off to imeicheck etc for repair.
The history so far
I have bricked my jasjam while updating to telstra wm6
I have not super CID my device before upgrading to telstra wm6
Now my device freezed at second splash screen
IPL 1.04
SPL 2.03
NO GSM
when i used the info 6 command on mtty it says NO CID
i can not upgrade my device from SD CARD (memory stick)
i used these command on MTTY.exe but no improvement
set 14
task 8
set 16
task 8
when i tried to rom upgrade using any ruu (ruuwraper,.....) it only shows 1% and my device reboots and ....
any suggestions????
I hope you understand this, Basically if
1. You have a "No GSM"
2. Your CID is corrupted
3. Your OS has no KITL mode
4. You didn't use HARDSPL...
Then your phone is screwed, and you need to buy a new one or send it to repair.
Hope you have better luck with your next phone. (you seem to be collecting bricked phones!)
Wam7 said:
4. You didn't use HARDSPL...
Click to expand...
Click to collapse
That's the BIGGEST mistake u ever made with ur Jasjam, bro
try to send to repair centre, if repair cost is too much. Than u have to decide try but new gadget. Kaiser looks flirt to me
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
st3v3 said:
yep im glad i waited to upgrade from the proper wm5 to the proper wm6
Click to expand...
Click to collapse
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
ermenzegna said:
Did u mean, u stay at proper WM5 or already Flash to WM6 ?
I think everything is save IF we read carefully the disclaimer from the author
Click to expand...
Click to collapse
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
st3v3 said:
The offical I-mate telstra Jasjam rom for WM6 came out recently previous to that i just kept the original WM5 rom that it came with much to the dismay of my peers, actually considered it a few times but decided against it till the official rom came out.
yeah if you follow the instructions for the WM6 rom you use it should be ok however the "Murphys law" of programming tends to suggest there will always be an error that they dont allow for.
Click to expand...
Click to collapse
This has NOTHING to do with only using official Roms! One has pretty much the same chance of bricking their phone evening using an official WM6 as a cooked variant from Schaps et al..
Simply put if you don't use HardSPL then you're asking for trouble no matter what the ROM. You should also use the MicroSD wherever possible as it is much more reliable.
imei check use jtag to fix this
imei check use jtag to fix this ,CAn we use jtag to fix this in hermes. need help to resovle spl 2.03 cid locked no gsm.
I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.
Dear Senior members,
I am new user of Gene 100( New) verified from both method SPLcheck ,Olipro and Orefkow Method and found that It's new gene n udated it's SPL..
Then i update my WM6 Rom to Sumit's Pro User ROM ( WM 6.1 for both Old and New Gene).
It worked fine.
The by mistake I click the file gene_hspl.exe ( The file using for Updating SPL for Old gene).
immediatly My phone got off.
i tried a lot to switch on it .
then I push cam key with soft reset key, then my phone on in boot loader mode with SPL 1.10.olip
and
ONBL 1.17.0000
Now i am Not able to update to my SPL again.
and Phone is not working, What should i do now..?
Should i Update SPL again or anything else.
I tried to update Newer ROM ,But message come with Error(300) Please get newer Update Utility for ur phone.
Kindly Solve out my Problem
ur device is still under warranty period??
Try to unbrick again from orefkov method if it works GREAT! otherwise take ur device to service center and dont tell him about cracking and just tell him that it automatically switched off...
dont try anything without suggestions of other GENE forum members..just ask them too what to do..?
If you are getting to Bootloader with olip spl. orefkov method should work. BTW, How did your Gene work with both Old and New Gene ROMs???
AND WHY DO YOU NEED TO POST THE SAME QUERY WITHIN FOUR MINITUES?
IF YOU ARE IN SUCH A HURRY, BEST PLACE IS THE SERVICE CENTRE.
Addicted2xda said:
If you are getting to Bootloader with olip spl. orefkov method should work. BTW, How did your Gene work with both Old and New Gene ROMs???
AND WHY DO YOU NEED TO POST THE SAME QUERY WITHIN FOUR MINITUES?
IF YOU ARE IN SUCH A HURRY, BEST PLACE IS THE SERVICE CENTRE.
Click to expand...
Click to collapse
cool down addicted...he is just embarrassed....
vikas _khatri1981 said:
Dear Senior members,
I am new user of Gene 100( New) verified from both method SPLcheck ,Olipro and Orefkow Method and found that It's new gene n udated it's SPL..
Then i update my WM6 Rom to Sumit's Pro User ROM ( WM 6.1 for both Old and New Gene).
It worked fine.
The by mistake I click the file gene_hspl.exe ( The file using for Updating SPL for Old gene).
immediatly My phone got off.
i tried a lot to switch on it .
then I push cam key with soft reset key, then my phone on in boot loader mode with SPL 1.10.olip
and
ONBL 1.17.0000
Now i am Not able to update to my SPL again.
and Phone is not working, What should i do now..?
Should i Update SPL again or anything else.
I tried to update Newer ROM ,But message come with Error(300) Please get newer Update Utility for ur phone.
Kindly Solve out my Problem
Click to expand...
Click to collapse
jsut update ur spl by using spl for new gene.
this will do
Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started, it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didnt work when i tried with Olipro jumpspl method it says the Update Utility is invalid, when i tried with Orefkov mtty it says cant unlock the CID or basicaly it says cant place the SPL and finally i tried the Olipro HSPL method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU i tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEW BEES ALSO PLZ HELP......!!
Now i m using the stock rom which came with gene,i added a lot applications i somehow managed to get touch control for scrolling and all everything ok.....but i miss the WM 6.5 style MENU, TASKBAR, FREE RAM and most of all the TITANIUM it was my favourite i was using Duron's WM 6.5 for new gene it was very cool...
Now i feel like crying i am addicted to WM 6.5 PLZ HELP...
Hey Guys I have a HTC Gene p3400i previously i spoke to guys like sumit and Krazy also, first i had a motherboard series of HT8X, i somehow unlocked the CID using Orefkov method, but everything was fine oneday i flashed it with a Wrong Stock ROM and thats where the problm started.
it got bricked i took it to service center the technicians were very helpful they changed the motherboard to a new one of HT8X series, i tried to unlock the CID/Change the SPL to either Olipro or Orefkov both didn't work when i tried with "Olipro jumpspl" method it says the Update Utility is invalid, when i tried with "Orefkov mtty" it says can't unlock the CID or basicaly it says cant place the SPL and finally i tried the "Olipro HSPL" method it goes to boot loader shows Olipro 1.10 in SPL but when i flash a Old gene ROM the RUU utility says or wants a new RUU.
I tried it around 5 times continously starting from monday to Friday and totally it got bricked for 5 times also, i took it again and again to service center the guys didnt hesitate they were really helpfull they unbricked it, i even asked would i get my previous motherboard they said its already been sent to HTC for Fault Repair.
Now the methods which i can't use:
1) Olipro HSPL (which again bricks)
2) the Orefkov mtty (which says cant place the spl)
3) the Olipro Jumpspl method which shows a Blank white screen but when try to update using RUU says requires new RUU
PLEASE HELP.....!! THIS HAS BECOME A CHALLENGE FOR ME>>>>>>>> I READ ABOUT THE SAME PROBLM IN THE FORUM BY NEWBIES ALSO PLZ HELP......!!
can you please let me know is it new gene or old gene?
ankuhadia said:
can you please let me know is it new gene or old gene?
Click to expand...
Click to collapse
yes previously before changing the motherboard it was HT8X series but was new gene now its same series but it is old gene....