Related
Hello.
I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... And I also thought it was harmless to just try and see if it worked. But I got an error around 92-93% and after that my device won't start. So my radio ROM might be screwed.
I'd like to flash my ROM with the i-mate one (JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship.exe) and then add the ext-rom. But how do I do that when I can just access the bootloader screen? And do you think it will boot again if I'm able to flash it?
Here's some more info about my device:
HERM100
IPL-1.01
SPL-1.04
Thank you very much in advance. Help will be highly appreciated.
No your rom *is* screwed. You can get into bootloader, you can even get to 11% of a dopod etc rom upgrade if you try, but you will not flash a new radio.
You CAN boot the device.
Do a hard reset, but do not press spacebar to reboot after. Instead, do a soft reset. The unit should boot but as you've screwed the radio you will not get a gsm signal and the phone will say unknown sim status.
I know this as I bought one cheap after the owner had done exactly the same as you.
IMEI-check's unlock solution is the only one that works IIRC, and in some cases this re-writes the security area of the phone and repairs similar issues, but in this case I could not get the prog to read.
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Currently you cannot book the m3100 in through the web as it's too new, instead email / call them.
http://service.htceurope.com/
edit - or if you're an orange customer ring 150 and act dumb saying it ' won't work'.... :wink:
Richard
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
pof said:
What happens if you just leave the phone in bootloader mode and then try to flash any ROM (imate, dopod, htc...)? run 2 times the RomUpgradeUt.exe if you get an error on the 1st try.
If you get an error while running the rom upgrade utility you can monitor the USB port while upgrading (you will see the real error from the bootloader then), there's some more info on this wiki page:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
good luck
Click to expand...
Click to collapse
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages. As described in my post above, it will get to 11% and stop. The device will be in the same state as before, with the same ext rom, but the splash screen and bootloader will have changed.
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
There is no error from the bootloader - as there is no radio rom present and no security area the upgrade process just hangs.
Richard
fluffcat1 said:
No, if you want to send it back under warranty do not try to run a rom update as there are no orange rom packages.
[...]
i.e: it will be bloomin obvious you tried flashing it and failed. Not what you want if you try for a warranty repair....
Click to expand...
Click to collapse
That's true, do not try to flash any other roms if you want to use the warranty or send the device back...
Thank you very very much for your help guys.
As I'm the administrator of these devices in the company I work for I just grabbed a new SPV and will send this thing back to Orange. It sounded like I'm getting a new one..
Well, I think I've learnt my lession.
Oh, and I have another question. Is there a reg editor I can install on this one so I can remove the app lock? I know I can install java apps, but it's a bit grumpy about apps that needs installation (the developer must be certificated).
Cheers guys.
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
pof said:
Hi,
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
The rom must match your CID. Let us know if it works
Click to expand...
Click to collapse
Errr, did you read the last post? He sent it back......
Richard
I just wanted to let him know there's a possible solution, it just in case he still has the unit
pof said:
I just wanted to let him know there's a possible solution, it just in case he still has the unit
Click to expand...
Click to collapse
Maybe his search is broken as well as his old phone eh?.... :roll:
fluffcat1 said:
You need to return the device to HTC - you'll need to pay approx £35 for reflashing back to the orange rom. This is what I had to do.
Click to expand...
Click to collapse
Sorry to take the thread a bit OT, but just wanted to confirm this again.
So, if I flashed my M3100 with a different ROM, and then had to return the phone to Orange for repair for a different reason, I can send it back to HTC just to have the ROM reflashed, and then send the phone to Orange to get the repairs done?
I've been hesitating on whether to flash the phone with a non-Orange ROM because I didn't want to give up the ability to obtain warranty repair (as there is no ROM upgrade yet). If it's just a matter of £35 and then everything else as normal, maybe it's not so bad...
Thanks!
My SPV M3100 won't start!!!
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
rachelm700 said:
I also did this, so if anyone can find a solution it would be greatly appreciated.
Also tried this and it didn't work for me:
Try to flash a new rom using the SD card method described here:
http://forum.xda-developers.com/viewtopic.php?t=62596
"I have a problem I hope someone here can help me to solve..
I have an Orange SPV M3100 that hangs on the Windows Mobile screen when I try to start it.
I'm able to go into bootloader mode, and i have tried using mtty142.exe with the set 14 0 command. It still won't boot. I've also tried to hard reset it.. still won't boot..
What I did was trying to unluck the SIM-lock with the Universal unlocker (HTC_Uni_Unlock_v1) from buzz. At the time I thought universal meant that it worked on all HTC devices (stupid, I know)... "
Click to expand...
Click to collapse
the above link doesnt work?
zohaer21 said:
the above link doesnt work?
Click to expand...
Click to collapse
IIRC it is this link on the new forum:
http://forum.xda-developers.com/showthread.php?t=277281
spv m3100 don't start
hello guys
I have the same problem about spv m3100. I used "universal unlock tool" to unlock my device and now it don't start,don't boot...I tried the Hermes SD Card flashing methods with qtek001 rom and, a white screen with "loading...." appears for 2 second and then nothing else appened. I think that the method is right but I need to use a different software. what do you think about?
please help me
thankksssss
My SPV M3100 won't start
SD card method is no good as there is no upgrade from Orange until January.
Tried to do a radio upgrade explained here:
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
But it didn't work just came up with connection error, tried to monitor USB but nothing showed up to find out why, althouth mtty commands always do show up in USB Monitor.
Still have a brick and looking for a solution, hopefully, someday, please someone help me I am loosing my mind.
Hello
How to enter boot mode on HTC 200 ?
My htc hangs on HTC screen.
I'm trying to reflash it.
Thanx
Chris
@chrisro, Please read the wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_Resets
Thank you very much.
Greets form Poland !
Chris
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
nstefanelli said:
I was flashing my brothers phone for him, and I was using the CID Workaround, and it completed, and then after a hard reset the device wouldnt go past the first splash screen.. pllease help
Click to expand...
Click to collapse
Check your PM's
bwesty said:
If your able to get into bootloader mode then you should be able to flash another rom such as wizard love or your providers rom.
If you read the thread on unlocking G4 cid locked using shell tool you will see what i mean. I personally was stuck in a very similar situation and received help, so the info you need might be in that thread.
Click to expand...
Click to collapse
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
jUST DO WHAT I SAY
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
samy.3660 said:
gREETINGS,
Just follow this steps u will be out of it.
Press and hold the camera button and reset the phone, hold the camera button until you see the tri color screen (bootloader), when u are on tri color screen connect the USB with your phone(dont see for active sync it wont recognise but it will be connected), and then flash your phone with the rom your provider has given you i.e, the original rom and DONT flash it with shell tool use the exe file of the rom.
When you are at the original rom then try to flash the WM6 with shell tool and follow the instruction properly.
Thanks
Click to expand...
Click to collapse
I cannot do that because the Carrier ROMs that I have aren't for G4, so they arent working. I have three different carrier ROMs for my phone.. and none of them work.
-Stefanelli-
nstefanelli said:
i used the shell tool, but i just got stuck on the first splash after i did that.... here are device specs
Its a Cingular 8125, obivously g4
IPL 2.25.0001
SPL 2.25.0001
It doesnt get past bootloader, and I would really like to put WM6 on it.
At this point, I've tried various other ROMs and nothing is working. Any thoughts or ideas at all would be appreciated. Thanks.
Click to expand...
Click to collapse
Check your email, I downloaded and zip works fine here.
i'm facing this problem right now , i will solve it with the original rom .
the problem started when i used shelltool to upgrade my G4 CID Locked to windows mobile 6 crossbow underground edition .
i will give it another try when i get my device alive again ,
any suggestions for the WM6 underground to make it work using shelltool on my wiza 200 ??
--------------------- Edit -----------------------
Finally i solved the problem and installed Crossbow WM6 underground edition .
all i did is to install the original rom from provider and then used shelltool to install WM6 .
i want to mention that my wiza200 is G4 and its CID Locked .
Huge thanx to mUn , you are da man
Mmm
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
lobiik said:
I've tried underground wm6, but flashing till 96%, then error 302. I've searching for love rom few hours at night, then finally found, it is using the same flashing frontend (but in italian? language), flashed ok, phone's running. I've tried some few other wm6 roms, but always errors like "too old, get new one" or once it was probably fake, because it loaded exactly the same ROM as love one is. So, now I've probably stuck on WM5 at all
Click to expand...
Click to collapse
whats your device and is it G3 or G4 ?
try to do as i did and it worked for me , install the provider flash , then try shelltool to flash WM6 underground .
WBR
a-h-t1 said:
whats your device and is it G3 or G4 ?
Click to expand...
Click to collapse
Mine is G4, dunno if cid is locked or not. I've flashed it as I said with wizard love rom and working without problems. I've tried that again this morning, to flash from love rom, but the same. At 96% it hangs, error 302 Communication error, then starts recovery process, phone goes to bootloader mode. Then is possible to flash it with love rom again with no problem
g4
i have a g4 wizard using the shell tool i have chaged my rom on my phone sometimes 3 times a week just to test them out
the shell tool works if you cant download from the forum here is the link for it
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
G4
yes, but when I run shelltool, and press get rom info, all fields states N/A
info from phone is:
ROM Version: 2.26.10.2 WWE
Radio: 2.25.11
ExtROM: 2.26.10.105
IPL/SPL: 2.17.0001
And anyway, dunno exactly which rom for WM6 I can put in (I've just 5.underground_edition_Crossbow_ROM.exe which stucks at 96% with 302 error)
well, I'm dumb, mislooked one stupid thing. Everything passed without errors, Windows Mobile 6 is up and running
happy to know that , the problem was installing rapi ha ??
WBR
No, not really, rapi and that second cab was in device, it was restarted, but I did a mistake - i didn't copied that desired rom into updater directory - that was why were all fields N/A... did that, flashed on first try, without problem
I had the same problem, orginal rom from the provider, and I can reflash it again.....
THX for the info......
ROM verion and link location
Hi lobiik,
which ROM did you use for your device, as you comments above:
"i didn't copied that desired rom into updater directory "
can you please point me to location where i can get the ROM, also proper steps to install the same.
Thanks,
Ajay
HELP!!!!!!!!
I tried flash my G3 with shelltools the program said it worked well i did hard reset then i turned it on it is stuck on 1st front screen bootloader mode is stuck i dont know what is is my device bricked
---------------------edit--------------------------
im a newbie
Dear friends at XDA Developers. I'm in big trouble. I set up the Vanilla OS on my TyTn and worked fine... then out of the blue I decided to upgrade it again and then some radio upgrade was performed and now it won't boot up. The phone is stranded in the splash screen at boot up but I can access the Bootloader (1.04) but if I use MTTY via USB I can only make some commands, info commands do not work (hang). Also, when trying to up/downgrade via SD card, it says "Loading..." and then "Checking..." and then no more (hangs). Now, I might be stupid but I have tried all possible threads in this forum (I think) but I can't find any solution. Please help me!!! :|
frosti said:
Dear friends at XDA Developers. I'm in big trouble. I set up the Vanilla OS on my TyTn and worked fine... then out of the blue I decided to upgrade it again and then some radio upgrade was performed and now it won't boot up. The phone is stranded in the splash screen at boot up but I can access the Bootloader (1.04) but if I use MTTY via USB I can only make some commands, info commands do not work (hang). Also, when trying to up/downgrade via SD card, it says "Loading..." and then "Checking..." and then no more (hangs). Now, I might be stupid but I have tried all possible threads in this forum (I think) but I can't find any solution. Please help me!!! :|
Click to expand...
Click to collapse
Here is the thread to go for help.
http://forum.xda-developers.com/showthread.php?t=286755
Hi i'm newbie
I'm french thus excuse me for my english
I try to upgrade my htc in WM6, i sucess, no problem.
After i upgrade with a rom radio and the upgrade block at 40 %.
Now the phone boot in tricolor mode.
IPL-1.04
SPL-2.10.Olipro
I find in the forum that for unbricked my htc i must to flash any rom in nbh format.
How to do that.
I try to install also original ROM_9600_FRA_10303.exe rom but activsync it not active.
Someone can help me please
thanks
Connect you device in bootloader screen with your PC with USB and you should see USB appear at the bottom of the screen on yor device. Now flash any .nbh with the RUU wrapper and select SPL 2.10 New bootloader and flash the ROM...
what is the RUU Wrapper, where can i download it?
unikgwada said:
what is the RUU Wrapper, where can i download it?
Click to expand...
Click to collapse
Here it is
RUU wrapper is a software?
Explain me which is it
unikgwada said:
RUU wrapper is a software?
Explain me which is it
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=298737
when i use RUUWrapper i havbe an error [260].
What i can do
In the tri color screen with the device plugged in via USB do you have USB written at the bottom? Does your device appear in the device manager?
Yes USB is written on the bottom, and yes the phone appear in device manager .
What are you using XP or vista?? You could try a different USB port or if that doesn´t work you may have to roll back the driver... read this http://forum.xda-developers.com/showthread.php?t=299657
I'm using XP.
When i use myyt.exe the phone make something, but when i try to upgrade any rom i have always this message error [260]
i try to update with rom radio 1.47.00.10 , the upgrade is correct 100%
but when i reboot i return in tricolor mode
I success to install rom with UUwrapper but now the phone block on the picture windows mobile
Thanks
i fine a the solution
Could you please share the solution ? I've got a similar case, thanks.
I was instaling NBD_v8.3_8MB trough shelltool on my MDA Vario then something happened and my PC restarted I whink it is because of the electicity .... so now when I restardet my phone it is stuck on the T-mobile screen Where it is writen.....
IPL 2.21.001
SPL 2.21.Olip
GSM 02.19.11
OS 6.6.6.666
Thanks in advance
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
well I looked all day what to do and I can not find solution
I just can not understand how to flash the phone
I found one solution via some kind of Wizard_love, but again I do not know what to do
Please help i am haveing the same thing just did it today i have the Cingular 8125....i have held camera+reset and got into these Red,Green,Blue,white screen and it says IPL 2.25 and SPL 2.25 now when i run the ROMUpdateUtility_Wizard_NoID it does not work i have my usb pluged in and my phone says USB please help
Thank you
PS.
I am running Vista
IPL 2.25
SPL 2.25
GSM 02.25.11
OS.6.6.6.666
_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-
Ok i have try everything. I have tried the RUU from the HTC site and even everything else when it is searching for the PDA and crashes idk why. I turn on my phone holding the camera and i get to the Red,Green,Blue,White...Plug the USB in and the phone says USB but not my computer??? so i don't know what i need to do please HELP i just got the phone and read you can do all this stuff
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
starkwong said:
1. Please use a PC with Windows XP
2. Download your original carrier ROM (i.e. Cinglular stock ROM) and flash back to original WM5
3. Install HardSPL or use SSPL
4. Flash to WM6
Click to expand...
Click to collapse
Were can i get HardSPL,SSPLand the flash back up?
all i have is the original rom
You guys wanna see bricked? I have a BRICKED! phone... My MDA was the unfortunate victim of a car accident. When my car went carreening off the road, my MDA went flying through the air and ended up on the floor of the car but not before hitting virtually every surface on the inside of the car.
Now my charge port is completely snapped off and my battery shorted out when I was trying to hold the charge port in place to charge it and fried the main board. DEAD. NO MORE.
THAT MY FRIENDS, IS BRICKED....
No worries though, I already ordered a TyTN II
Cool can you help?
Oh and i had the same problem with my mda and i got it replaced from tmobile. - the easiest way to reapair an MDA is getting it replaced ^^
offtopic
@dharvey4651
Why didn't you buckle up your phone?
Well i got mine up and running agian just used XP and install the RUU from HTC YES.......Now when i go to install WM6 when i press update were it should show me the Ver. of the one i am installing on my phone it does not say why please help and what do i need to install WM6 on my phone?
Just a quick question did you read the other threads there are already. They basicly explain everything clear and good
i have just still stuck on some stuff
dferreira said:
First of all, its not bricked. Bricked = doesn't turn on, nothing, blank screen.
I've looked to your info, you already have HardSPL, so you can flash directly using any RUU, don't use shelltools!
Enter bootloader (hold camera+reset), open up the RUU of the ROM you want (make sure it doesn't have any IPL/SPL) and flash away
Click to expand...
Click to collapse
jukata
first of all,as dferreira has assured u that ur device is not bricked,secondly ,you already have HardSPL,that means your device is unlocked,just follow his instructions,download any wm6 Rom and flash,it'll good to go,but if u still want to be sure,download WST Tool from the below given thread read carefully and apply the tool to verify the status of ur device,
http://forum.xda-developers.com/showthread.php?t=329170
u can flash NBD rom which u have or any other wm6 rom,goodluck
NVM i am on the Other Page! Thanks
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
kastro said:
Ok, i have read everywhere and can't help myself, so if someone would be kind enough to help it would be much appreciated
Ok, Used SoftSPL and tried flashing the ROM. It manages to get to 99% and then just goes RED. I have tried 3 different ROMS and same story it goes RED at 99%.
When i remove the battery, it goes to the RUU Red, Green and Blue screen. SPL version is 2.16.0001. Not Oli's new one.
What do i do from now?
Click to expand...
Click to collapse
Soft SPL only allows you ONE update, so phone is CID unlocked only when Soft SPL is loaded.
It's normal for the RUU to stick on 99 % for a couple of minutes, The whole update will take aprox 10 minutes.
You can try the hard SPL from there you are semi-permanently CID unlocked.
Good luck,
EquinoXe