Fitting screen protector from clear protector - Touch HD Accessories

Is flippin impossible! After peeling it off the backing it promptly got a load of finger prints on which are impossible to get it out.
It says to fit using soapy water then to push it out with a credit very nervous about doing that as i don't want to get water down the speaker hole, or down the lip on the edge of the screen.
Anybody got any suggestions?

Ryanmt said:
Is flippin impossible! After peeling it off the backing it promptly got a load of finger prints on which are impossible to get it out.
It says to fit using soapy water then to push it out with a credit very nervous about doing that as i don't want to get water down the speaker hole, or down the lip on the edge of the screen.
Anybody got any suggestions?
Click to expand...
Click to collapse
These are a real pain, i will tell you what i did.
1) Place a damp tissue firmly around a credit card
2) Peel a bit of the backing of the screen protector, near the speaker and camera side.
3) Line the exposed screen protector up with the phone, (this is tricky, as if it does not line exactly you will end up with air pockets)
4) Using the credit card with the tissue paper, slide it firmly from the top down to the bottom, ensuring that you pull the backing out as you go along.
If all goes well, then hopefully no air pockets.

They certainly are tricky but not impossible as my mate did a superb job on his - you can barely tell it's there!
I tried doing what he described but still it isn't perfect.
He said to use a spray bottle with soapy water (not too much soap)
Remove the backing & spray the underneath of the protector & let any excessive water drip off.
Then use a credit card to 'squeegee' the water out after you position the protector in place against the screen.
It looks bad for a day or two even once the bubbles are out but it improves.
It's true though, they should have made it about 0.3 mm less wide so it fits better on the screen.

dam.. those things are always triky!!

Related

The best way to apply a screen protector on the XS

So thought I'd share this as I think I have figured out the best way to stick one on without bubbles!
Before anyone states that a screen protector is pointless because there already is one on blah blah, I disagree because I just like the reassurance that if the screen gets scratched it doesn't matter. Plus that preapplied screen protector is very good and well applied (obviously) so its a waste just to use that as a protector alone.
On my older phones I have always ended up scraping the screen protector because the bubbles annoy me so much, and they're a pain to apply. But with the XS I tried and got it perfect, thought it was just luck, but did it again and achieved a good result again.
First turn of the phone for 10 minutes (apparently the heat can cause bubbles) Wash your hands, clean a desk area and take your top of (wear a tshirt)
then clean the screen, its obviously but really clean it (I use a wet wipe and then dry it off with a clean cotton top) if you have the special cloth use this too.
Get a lamp and shine it on the screen check for any streak marks and polish these away until the screen is perfect. Blow gentle to remove any dust particles small hairs etc. I have found in the past that bubbles often have a hair in the middle of them which prevents the protector from not properly sticking.
Now the tricky bit, pull at the '1' tab to remove the protector sheet, but do this with that side facing downwards (so that any dirt in the air wont land on the sticky side) and lower it towards the screen.
Align the corners with THE TOP of the phone next to the sony logo and curve the protector so that the top of the protector touches the screen (the area around the speaker grill and logo. Double check that everything is aligned so it will fit perfectly when you lay down the rest of it. Don't worry about any bubbles here as they can be squeezed out easily (due to the speaker grill).
Now grab a card of some sort, my driving licence seems to work best and place it where the top of the screen protector has been applied. With the right hand keep holding the protector at the edge of it, and with your left hand firmly press down the card and slide towards the bottom of the phone. (be firm at this point don't worry the screen will be fine it can take this pressure!)
Slide all the way down and look at your job. hopefully there should be only a few bubbles around the edge, if there are ones in the centre then carefully peel it up and try again. (don't touch the sticky side obviously and make sure you don't touch the screen.
The bubbles around the edges and around the speaker grill can be squeezed out using the card. Go over it a few times and then pull the protector sheet '2' tab off. And there ya go a nicely applied screen protector!
I tried to be as detailed as possible but may post pictures later if people require them.

[Q] Best way to clean the outside of your i9100?

Hello,
I noticed that after a few months of using my Galaxy S 2 with a rubber case it gets really dirty on the surface, specially the parts that are in contact with the rubber case.
Some of the dirt comes from dust and I guess humidity of the environment letting the back case of the cell phone a some kind of greasy spots. I tried to clean the battery cover with some water with soap and so the bottom part that is attached to the cell phone itself where is the speaker (always being careful of not getting into the speaker) but it appears that the spots doesn't want to disappear.
Is there any good tips about cleaning the case of the cell phone? like to take off those greasy spots that left behind the use of a rubber case?
Thanks for the answers B)
Normally I just use a cleaning cloth for glasses and wipe the phone with it, without any water/soap, works just fine and squeky clean most of the time.
Yeah I tried that.. but for the screen is ok, the problem is with the rest of the cell phone.. As it has spend to much time with the Rubber Case on it got a lot of greasy spots that cannot be clean off with just the cleaning cloth...
Is like if it is kind of sticky glue or something that got attached to the back of the case from the Rubber protector

[Tutorial] How to Remove the Shatter Proof Film

So after much thought i considered the pros and the cons of removing the film and decided to remove it as the oleophobic had worn away in less than 2 months. This will give you the information you need to remove it if you wish and how to do it properly without damage to your device or at least help you to not damage it.
1st. The tools you will need are as follows
1. razor blade thinner and or flat at one end
2. nail polish remover ( to remove the glue after)
3. cloth of some kind microfiber preferred 2 works best
4. "Recommended if no screen protector replacement"
Rain-x or some kind of wax or an oleophobic coating apply several coats
5. band aids or tape for your fingers as they will be put through alot of pushing and will be raw afterward
so know that this won't come in 1 sheet it will be coming off in chips and if your lucky it will come in larger chips and small sheets. when you start pick a corner that you can get at easlily. once you get a little up know that your going for a large enough area that you can get the entire blade under so you can slide it forward under the sheet as this will provide the least amount of damage if any the screen won't scratch this way but if you take the blade sliding up or down it will leave scratches so alway push the blade forward and leave it at a tilt just enough to get the sheet there is a layer of glue just as thick under. if you can see the glue when it comes up your doing well.
==warning== while you scrap this blade across your device be cautious not to get the sides of it as they are just high enough they will get scraped and nicked
after you have removed all the film you will need to use the nail polish remover to get the glue off it will come off slowly and there will be alot of small balls as it is moved off some will desolve the rest will come off in small balls. dont be afraid to use plenty it will make it will make it easier.
after all this wash with water only scrub clean and dry then apply a coating or screen protector whichever you wish .
==Important== know if you use wax some will get into the sides if your not careful with enough water and and cloth you can get access out. best to use waxes that are clear or liquid ones work well.
if you have any questions or if i have left anything out pls ask
Once you've peeled up 1 corner, you can use a credit card instead of a blade to slide it forward. It's safer that way.
If you're a single man and don't have nail polish remover, you can use concentrated alcohol instead. Cloth, Q-tips and rubbing alcohol worked really well for me.

Found way to remove LOCA glue when replacing front glass.

I haven't seen this posted already so I figured I would share. Anyways my brother just got a S4 for $120 but it came with cracked front glass. I told him I would fix the glass for him (my first time touching a S4 let alone replacing the front glass). Well I meant to take more pictures, but in the moment I just wanted to get the phone done. I followed a guide on iFixit and watched a couple videos on Youtube, alot of people are right when they say that the Youtube videos make it look simple. Anyways this was my first time working with LOCA glue (removing and replacing).
Here are some helpful tips:
#1 Make a jig that will hold your heat gun above your workspace, you will need to adjust the height depending on how well your heat gun works.
#2 Put some clear packaging tape on the front of the glass to avoid glass chipping and flying, also to keep glass from entering under the glass and scratching the digitizer..
#3 The glass is easiest removed with a temperature between 155f and 165f.
#4 Work top to bottom. Ear piece to button.
#5 When prying the glass off MAKE SURE you are between the glass and the digitizer, it is easy to lift the whole LCD assembly.
#6 Work slowly, if the glass if badly broken it will not pull up as easily as a less shattered glass. I found that the digitizer was not as fragile as I was made to believe.
#7 Have plastic razor blades or a plastic putty knife/scraper handy for the removal and cleanup of the LOCA glue.
#8 Have 2 lint free cloths handy for the cleanup and removal of the LOCA glue.
#9 When the glass is almost off remember to pry off the back and home button sensors from the bottom of the glass.
#10 When it is time to clean up the digitizer use your putty knife/scraper to get most of it up.
#11 I found that Eucalyptus oil works well at removing the rest of the LOCA glue. Just put some on a Q-tip and swab the area you want to clean.
Here is a pic of what the digitizer looked like after cleaning with Eucalyptus oil.
EDIT: Sorry pic wouldn't link, had to make it an attachment.
I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
fyca said:
I haven't seen this posted already so I figured I would share.....
....I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
Click to expand...
Click to collapse
nice write-up. shame that the image alone has over 500 views and nobody else has hit the "thank" button
well i thank you @fyca for the info and your time! :good:
Hey guys,
My first digitizer replacement ended up in a few big flower shaped flecks on the screen. That is not what I expected. I am very curious to know how these flecks appeared, or how I could avoid this will happen again. Also it looked to me like the original brightness could not be achieved.
This is the phone (Jiayu G2s) with the Calendar active which is almost an entire white display.
anybody who recognizes this?
oh, and by the way everything functions normal.
1_Petje
Looks like you overheated the actual screen. If you apply too much heat you will lose colors/brightness in those areas.
Heat not the only cause......
1_Petje said:
Hey guys,
My first digitizer replacement ended up in a few big flower shaped flecks on the screen. That is not what I expected. I am very curious to know how these flecks appeared, or how I could avoid this will happen again. Also it looked to me like the original brightness could not be achieved.
Link removed because someone failed to think;New posters have to quote the question in their posts, and may quote a link...Sheesh! //i58.tinypic.com/2duawkm.jpg
This is the phone (Jiayu G2s) with the Calendar active which is almost an entire white display.
anybody who recognizes this?
oh, and by the way everything functions normal.
Click to expand...
Click to collapse
The "flowers" that you see can be caused by too much heat. BUT, these appear to be the result of excessive pressure placed on the display. If you press hard enough on almost any lcd or led display you'll see these kinds of patterns. If you let off they go away, unless you've pressed to hard or too long. AMOLED are particularly sensitive when heated. Long and short, be careful how much pressure you use when removing the glass etc....
I replaced an s3 screen twice. It was obviously easier the second time, as there was no LOCA to fight with. The main reason for diminished clarity and sharpness after replacement is the absence of the LOCA. Once u manage to get the glass off and do the necessary cleaning/preparation for reassembly, applying 3-4cc's of LOCA onto the digitizer in a vertically stretched "X" pattern will give u that genuine factory screen appearance. Well...After u cure it under UV light. But...for a novice, applying the LOCA and making it look good without permanently damaging the device is extremely tricky. And shouldn't b attempted if you're not somewhat of a professional, as the glue can seep down into your phone's internal hardware.
fyca said:
I haven't seen this posted already so I figured I would share. Anyways my brother just got a S4 for $120 but it came with cracked front glass. I told him I would fix the glass for him (my first time touching a S4 let alone replacing the front glass). Well I meant to take more pictures, but in the moment I just wanted to get the phone done. I followed a guide on iFixit and watched a couple videos on Youtube, alot of people are right when they say that the Youtube videos make it look simple. Anyways this was my first time working with LOCA glue (removing and replacing).
Here are some helpful tips:
#1 Make a jig that will hold your heat gun above your workspace, you will need to adjust the height depending on how well your heat gun works.
#2 Put some clear packaging tape on the front of the glass to avoid glass chipping and flying, also to keep glass from entering under the glass and scratching the digitizer..
#3 The glass is easiest removed with a temperature between 155f and 165f.
#4 Work top to bottom. Ear piece to button.
#5 When prying the glass off MAKE SURE you are between the glass and the digitizer, it is easy to lift the whole LCD assembly.
#6 Work slowly, if the glass if badly broken it will not pull up as easily as a less shattered glass. I found that the digitizer was not as fragile as I was made to believe.
#7 Have plastic razor blades or a plastic putty knife/scraper handy for the removal and cleanup of the LOCA glue.
#8 Have 2 lint free cloths handy for the cleanup and removal of the LOCA glue.
#9 When the glass is almost off remember to pry off the back and home button sensors from the bottom of the glass.
#10 When it is time to clean up the digitizer use your putty knife/scraper to get most of it up.
#11 I found that Eucalyptus oil works well at removing the rest of the LOCA glue. Just put some on a Q-tip and swab the area you want to clean.
Here is a pic of what the digitizer looked like after cleaning with Eucalyptus oil.
EDIT: Sorry pic wouldn't link, had to make it an attachment.
I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
Click to expand...
Click to collapse
hi. thanks for the tip... i have 1 question at the moment, and it might sound silly... but what kind of eucalyptus oil did you use and where from? i did a search on it and there were all sorts of brands and use, and seems forms of it...
i like lighter fluid personally but its to runny but is perfect it you can keep it from behind the lcd and messing up the sheets on the likes of a LG G3.
The eucalyptus oil I used was an essential oil from my local co-op/natural foods store.
Go to lcdbondingusa dot com. They have this cleaner for cleaning LOCA. Man let me tell you, it's well worth the cost. I use a diabetic syringe to get it between the LCD and Digi. Sure does make easy work of it. It's great for other stuff, too.
" Lcd Adhesive Remover Cleaner For UV Glue OCA Glue iPhone & samsung Safe To Use" is the way it was layed out on the eBay page

How long to find all the protective plastic?

I've had my new S21 for a few hours now, and I keep finding more and more strips of the protective plastic that needs to be peeled off . Does anyone make a special light which make this plastic fluoresce? Could be a great new product!
LOL, I agree.
If I recall correctly, think I found the two big obvious sheets covering the back plastic and the screen glass. Another smaller sheet covering the camera bump and lenses. Then two (three?) very skinny separate strips wrap the circumference of the phone (the metal frame). One starts just to the right of the bottom speaker grill and runs up to the power/volume buttons. Another strip from but button around the top of the phone. And a third strip from the left of the SIM card and up the left-hand side frame. The strips along the circumference are hard to see or feel, and you need to find the start/end of the strip in order to begin peeling it off. I used my fingernail to find each end-point, then picked at the end until it came free enough so I could grab and pull up the entire strip.
I hope I found them all as I've put the phone into a Samsung leather case, which fits so snugly I can barely get it back out.
Leave it be and case it.
Without a case it only a matter of time until it self destructs.
As the protective film works its way loose remove so grit that gets trap under it doesn't mar the phone's finish. Otherwise it helps to protect from case marring.
Leave the display factory protector on as long as possible until it degrades.

Categories

Resources