Is flippin impossible! After peeling it off the backing it promptly got a load of finger prints on which are impossible to get it out.
It says to fit using soapy water then to push it out with a credit very nervous about doing that as i don't want to get water down the speaker hole, or down the lip on the edge of the screen.
Anybody got any suggestions?
Ryanmt said:
Is flippin impossible! After peeling it off the backing it promptly got a load of finger prints on which are impossible to get it out.
It says to fit using soapy water then to push it out with a credit very nervous about doing that as i don't want to get water down the speaker hole, or down the lip on the edge of the screen.
Anybody got any suggestions?
Click to expand...
Click to collapse
These are a real pain, i will tell you what i did.
1) Place a damp tissue firmly around a credit card
2) Peel a bit of the backing of the screen protector, near the speaker and camera side.
3) Line the exposed screen protector up with the phone, (this is tricky, as if it does not line exactly you will end up with air pockets)
4) Using the credit card with the tissue paper, slide it firmly from the top down to the bottom, ensuring that you pull the backing out as you go along.
If all goes well, then hopefully no air pockets.
They certainly are tricky but not impossible as my mate did a superb job on his - you can barely tell it's there!
I tried doing what he described but still it isn't perfect.
He said to use a spray bottle with soapy water (not too much soap)
Remove the backing & spray the underneath of the protector & let any excessive water drip off.
Then use a credit card to 'squeegee' the water out after you position the protector in place against the screen.
It looks bad for a day or two even once the bubbles are out but it improves.
It's true though, they should have made it about 0.3 mm less wide so it fits better on the screen.
dam.. those things are always triky!!
Hi,
my XPS gets dirty already. You really see it on the surface of the phone. Whats the best method to clean it or how do you guys clean your white SXS? Rubbing with my finger is not enough.
greets
PhilAd
I use a microfibre cloth. I dampen it slightly if I cannot get any excess dirt off.
Microfiber cloth should do the job... Also you can use min cream if the dirt is too stubborn ...
what exactly is min cream?
dampen and microfiber does not help :-/
Try using an eraser to rub off the stain..
Personal experience - only use eraser if the stain is real bad, cos the top coating may be rubbed away. It happened to me.
If eraser alone doesnt work as well, apply a thin layer of toothpaste (which contain small amount of breach) on top of the cover, wait till it dry and then rubbed away the toothpaste with an eraser. Again use this method only if the stain is persistant and cant easily be removed.
*decides to get black*
ok i'll try an eraser carefully and see what happens.
EDIT: Rubber does also not work. I will address that to sony. anyway they are exchanging devices in germany that have problems with yellow spots on the display when the device is getting around 40°C.
A big thanks to several members of this community, biggest thanks goes to T-R as I followed much of his instructions here
My goal was to replace the back but also place metal plates for my CD tray magnetic car holder.
I ordered three of the factory second backs from SlickWraps, the dark leather, football leather and cork. My first try was going to be with the cork as I figured it to be the most forgiving. I ordered the same plastic sheeting and 3M strips that T-R ordered.
Tools I used:
Hair Dryer to heat back
Library card to help peel off back
Pick to start initial prying of back
1/16th drill bit for microphone hole
Xacto knife to cut plastic sheet
Dremel to cut metal plate
I'm not good at step by step instructions so I apologize for not walking through what steps it took to make this happen. Feel free to ask if you are curious. My first attempt at the metal plate was too big and the back kept popping off. I put only one of the plates back over the little divot under the camera but didn't take pics before putting back on again as I didn't think it would work, seems it did.
My pros and cons and pics.
Pros:
Love the feel of the cork
Feels close to stock when not being nit picky
My slickwrap experience was great, order on Wednesday, in my mailbox on Friday
Fit of the cork back is impressively good minus one issue, see below
Cons:
Buy extra stickers, I screwed up the first and was glad to have a second but will need more if I want to change it
Mic hole is no where near where it should be on the cork back, might be part of why it's a factory second
Stickers are not as strong as the Motorola goop
Rookie mistake:
I had left the screen naked while working on all of this and scratched the hell out of it (my standards, others ask where when they look at it)
thanks for sharing. always love to see pics of what others are doing. what kind of magnetic holder do u use? any pics of the damage to the screen?
sand1303 said:
thanks for sharing. always love to see pics of what others are doing. what kind of magnetic holder do u use? any pics of the damage to the screen?
Click to expand...
Click to collapse
I tried taking a pic of the scratches and they don't show up well; they are probably not as bad as I make them out to be. I switched over to this mount because it has the strongest magnet I could find in a CD mount holder.
I'm tempted to switch the back out for one of the leather ones, I'm never satisfied.
No matter how nice it looks, it's certainly not worth scratching the screen for. I never put my phone face down on any surface that is not soft and I've never scratched the screen on any of my numerous phones. I hate screen protectors because they always look and feel horrible but I am super careful about the screen. That's the bit you interact with all the time and it would really bother me to have even the slightest scratch on it.
Otherwise, good job.
Was curious on how the plastic backing under the skin was holding in terms of sticking. I was thinking about doing the same thing and wanted to know how good the plastic/tape combo was at holding over time. Any lifting occur?
Jawrduhn said:
Was curious on how the plastic backing under the skin was holding in terms of sticking. I was thinking about doing the same thing and wanted to know how good the plastic/tape combo was at holding over time. Any lifting occur?
Click to expand...
Click to collapse
My first install was my learning exercise and I can't say it would have survived long term, started popping up on the edges. Just this past week I installed the football textured leather back and am very happy with it. Thus far it is not popping up anywhere but I had learned a lot from my last install. New learnings:
Have a brand new x-acto blade, works so much easier making the plastic template back
Scuff the plastic backing before applying the sticker, it comes shiny and smooth
I bought a heat gun and found out quickly the plastic back can warp easily so be careful when heating it
Still heat it though and hold for a good 30-60 seconds after
Leave a small gap around around the sticky tape after applying to the back, if you try to cut it perfect you land up with a bare edge
Install the plastic back first to the phone, leave it for a day if you can. If it pops up, heat the hell out of it and hold as strongly as you can for a minute or so ( I wore gloves)
Heat again after applying the leather back, heat really helps the application stick
If you buy the regular leather be aware it's not treated with any water resistance or proofing and any water will mark it.
If you are buying the Factory Second versions buy a couple, they are only $10 each and $2 shipping total.
The bump near the camera is from the metal plate I installed for my car mount, I couldn't fully conceal it.
thepktrckt said:
My first install was my learning exercise and I can't say it would have survived long term, started popping up on the edges. Just this past week I installed the football textured leather back and am very happy with it. Thus far it is not popping up anywhere but I had learned a lot from my last install. New learnings:
Have a brand new x-acto blade, works so much easier making the plastic template back
Scuff the plastic backing before applying the sticker, it comes shiny and smooth
I bought a heat gun and found out quickly the plastic back can warp easily so be careful when heating it
Still heat it though and hold for a good 30-60 seconds after
Leave a small gap around around the sticky tape after applying to the back, if you try to cut it perfect you land up with a bare edge
Install the plastic back first to the phone, leave it for a day if you can. If it pops up, heat the hell out of it and hold as strongly as you can for a minute or so ( I wore gloves)
Heat again after applying the leather back, heat really helps the application stick
If you buy the regular leather be aware it's not treated with any water resistance or proofing and any water will mark it.
If you are buying the Factory Second versions buy a couple, they are only $10 each and $2 shipping total.
The bump near the camera is from the metal plate I installed for my car mount, I couldn't fully conceal it.
Click to expand...
Click to collapse
Awesome, thanks for the tips. I'm actually using a skin from TOAST so I'll see how everything pans out.
thepktrckt said:
My first install was my learning exercise and I can't say it would have survived long term, started popping up on the edges. Just this past week I installed the football textured leather back and am very happy with it. Thus far it is not popping up anywhere but I had learned a lot from my last install. New learnings:
Have a brand new x-acto blade, works so much easier making the plastic template back
Scuff the plastic backing before applying the sticker, it comes shiny and smooth
I bought a heat gun and found out quickly the plastic back can warp easily so be careful when heating it
Still heat it though and hold for a good 30-60 seconds after
Leave a small gap around around the sticky tape after applying to the back, if you try to cut it perfect you land up with a bare edge
Install the plastic back first to the phone, leave it for a day if you can. If it pops up, heat the hell out of it and hold as strongly as you can for a minute or so ( I wore gloves)
Heat again after applying the leather back, heat really helps the application stick
If you buy the regular leather be aware it's not treated with any water resistance or proofing and any water will mark it.
If you are buying the Factory Second versions buy a couple, they are only $10 each and $2 shipping total.
The bump near the camera is from the metal plate I installed for my car mount, I couldn't fully conceal it.
Click to expand...
Click to collapse
Is it a formed vinyl patterned or really leather? footballs are supposed to be made of pig leather right?
I'd like to see ostrich
LOL haven't seen Ostrich yet. It's definitely textured bovine leather not plastic and looks like it is treated as I haven't had any water stains yet.
Forgot to ask, when you said your first attempt had he edges raising, were you referring to the plastic or the leather?
lotus49 said:
No matter how nice it looks, it's certainly not worth scratching the screen for.
Click to expand...
Click to collapse
I agree. Even the slightest hint of a scratch and I would lose a bunch of sleep. But unlike you, I use a glass protector which feels like the phone screen.
Jawrduhn said:
Forgot to ask, when you said your first attempt had he edges raising, were you referring to the plastic or the leather?
Click to expand...
Click to collapse
Both but most of it was the plastic peeling off of the back of the phone. It was applied twice though and I'm certain that impacted the adhesion.
My Nexus with Cork back from Slickwraps.
http://kryon.smugmug.com/Purenexus/i-bRKJdsk/0/O/OPERATIONPNbanner5x1.png
Has anyone installed this without the replacement back? and if so can I get a pic?
How is the cork back holding out for you. Can you post any pics after wear and tear.
Sent from my Nexus 6 using Tapatalk
I am at work so I can't post pics but I made the jump and got one a couple weeks ago. I like the way it looks but if you tend to work on cars or have dirty hands from working, this is not for you. My cork back is filthy but not too noticeable unless you've seen it beforehand.
I'm diggin' the cork look!
Hi,
Unfortunately ceramic version also get scratches. After over year of using I've got some really ugly, big scratches on ceramic back.
I wonder if it is possible to polish back surface? Does anyone tried?
I have some experience with polishing car parts, but it's totally different item.
How do you think? Is is possible to polish ceramic? Or maybe I will get only worse...
Hello . Tbh I'm not sure what I would do. As it is a phone. How ever! It is possible to get scratches out of ceramic.
Take the back of (if you can)
mark with chalk all the scratches easy to wipe off.
get a bowl or something filled with nice hot water not to hot though you got a stick you hand in. Make it warm. Shuv some dishwasher liquid in. Good quality. Like fairy liquid or something.
CLEAN THEM SCRATCHES!
then wipe up the scratches and dry up with a clean cloth. One that doesn't leave bobbles or rubbish.
Put a small bit of brass polisher on a clean, soft cloth. Apparently tooth paste or vinagre works, but not tried it. Rub the product into the scratches and all the edges, like your wax a car. Circle Circle circles keep doing it. Eventually the scratches should no longer be visible.
you can stop there although when I did my bathroom tiles I used some car wax just to protect the areas.
I hope this helps. . Don't run at me with knives and lemons if it ruins your phone please xD this works on real ceramic....
Hope I assisted .
Mine with more or less one year old have no scratches in ceramic, only on the aluminium(?) edge and some light scratches in front glass. I have used it almost all time withou a case. !!!!
so, i have the unicorn beetle case for my S9 (and my fiancee's S9 as well) and this oil slick thing happened between the plastic of the screen protector and the phone screen. Ive cleaned the inside with windex, professional strength spray foaming g;ass cleaner, 98% isopropyl rubbing alcohol, dawn dish soap and warm water, dawn and cold water etc etc etc, ive even used a hair dryer to get it fairly warm and to allow the air to help move any water molecules from any pits in the plastic. In short, ive done a ton to this [email protected] thing and it persists. My fiancees case is fine and the older kiddos case for the A8 he inherited from me is the same brand and a year older than my case and has zero problems. I work in an office and dont get the phone near grease ever, so im baffled about where the oily stuff is coming from.
Looks like to me that it is moisture, maybe heat from the phone, humidity etc.
That is definitely moisture under the screen protector. If you already cleaned it and it came back, you will need to get new screen protector because this one has opening for water to enter and that can't be fixed
nash211 said:
Looks like to me that it is moisture, maybe heat from the phone, humidity etc.
Click to expand...
Click to collapse
Tomogitarist said:
That is definitely moisture under the screen protector. If you already cleaned it and it came back, you will need to get new screen protector because this one has opening for water to enter and that can't be fixed
Click to expand...
Click to collapse
thanks guys. this was my first plastic film style case with built in screen protector thingy. Wasnt a fan at first, got used to it and then this happened. Ive since order ed a new case, which obviously fixed the issue. The case is fairly cheap, its just a shame the plastic part only lasted that long. Thanks for the replies guys, the accessories area of a phones forum is usually a wasteland lol
I have been using one for the past 6 months on my Galaxy S9 and I've had no such issues. The only times this would happen was when I would wipe the screen with alcohol and a portion would get into the sides at the top.
The only reason that would happen is you got the phone wet at some point and the water found its way through the cut-outs. Of course, with no way to evaporate, it's probably going to stay there unless you remove the plastic cover clean it, dry it then return it.