hi
i tried to upgrade my o2 mini xda II from its current version..
as u said i dowloaded the above file and ran the HimaUpgradeUt file...
first- it showed up a screen saying its going to upgrade from current version to a newer version...and click on upgrade...
stage 1 erasing rom image....
from here it stoped...an error message occured saying
"error 112:CE ROM UPDATE ERROR"
there has been a problem updating your pocket pc software..
remove cable and reset...
i did but it doesnt restart...Serial v1.00 appears on screen.. i even hard reseted.. i doesnt work....
please help me....
Related
my himalya automatically rose frm dead..but it was Jus showin the splash Screen..so i decided it Flash it
i put it into the bootloader mode n started flashing
but i encountered a Error during upgrading the radio ROm
This is wat i saw in the RUULlog.log file
18:21:55 Connection with USB
18:22:29 Begin Stage 4
18:22:59 Radio Erase retry 1
18:23:29 Radio Erase retry 2
18:23:59 Radio Erase retry 3
now there is a splash screen n there it shows 'NO GSM' but i ttried flashing wit a Differnt rom but no Luck please Help me
Please help me my himalaya is dead since more than a week
you may send more info
like what rom was befoure and what rom are you trying to put in
with that i can try to help a litle bit
hope never dies just me......
Re: you may send more info
rictec said:
like what rom was befoure and what rom are you trying to put in
with that i can try to help a litle bit
hope never dies just me......
Click to expand...
Click to collapse
my himalaya was on original rom ..then i tried installing 1.66 version i also tried wm2005 but no differnce .. the radio version cudnt b eearased ..it was givin me an error as Quoted above..i guess i hve to give it to the service center only (
Dear friends
I was tring to upgrade my iMate Pocket PC also know as Himalaya with windows2003 SE , while upgrading I faced problems, the upgarde failed and now I am just getting no display and OS too. The only message displayed is
Serial
v1.03
nothing is working please help
bye with regrads,
your unit is still okay; even better that the usb version is showing on the screen. it's simply stuck on bootloader mode. what kind of problems did you encounter resulting in the failed upgrade?
one suggestion i can give before you downgrade is to try and proceed with the upgrade to se. put your unit back on the cradle but don't expect activesync to "recognize" the device. just put it back on the cradle and rerun the upgrade to se.
same thing happened when i upgraded but to wm2005. the screen showed error and the only thing on the screen was the usb version. i simply cradled back the unit and ran the upgrade. worked.
cheers
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
oh, it appears that you have the "wrong country" id issue. i'm not entirely sure as to how to avoid this but i believe it has something to do with the correct rom version (guys, correct me if i'm wrong). where did you get the rom you used for upgrading to se? downgrading might be the only trick if there is no rom for saudi-based users...but if any chaps presently living there and were successful in upgrading their units perhaps you could share the rom version/s you used?
cheers
yasirirfan said:
Hi
Thanks a lot, i tired those steps before and even now I did but its not upgarding I am gettig following error as show i the attachment. Please let me know what to do
thanks a lot
yas
Click to expand...
Click to collapse
To overcome the Country ID Error, first you need to install this tool...
ftp://xda:[email protected]/Tools/ER2003Edit_1_4_26.zip
Open the ROM file you want to upgrade, then change the appropriate 'Operator ID' code, after this click 'Save ROM image'.
Upgrade ur device. You will no longer face the error message.
What is this error?? Y cant i install radio rom on my xda ??
I've just gotten this error whilst updating my XDA Iii using the updater from the O2 website.
Its now stuck on a screen saying USB and v1.01.
Any ideas?
Anybody????????
Hi,
I have MDA Vario II, aka Herm300, aka Tytn ... My problem is that I've got "No GSM". So I got in forum and checked how to try to Fix it threads... So I tried by putting "Hard-SPL" and also I've tried to Upgrade "Radio", but every time when I start upgrade I recieve "Error 262" at 0%, I changed several Radio's but I had always same result. Also I've tried to downgrade to Official Rom of WM5 and it stops at 13% witn "Error 262" . So my Question is:
Is it possible that I have hardware problem not radio problem .
ATM it works fine with Schap's ROM as PDA and "No Gsm" Again ...
On Bootloader I got:
IPL-1.01
SPL-1.40.Olipro
If there is another solution that may help I'm open for advice.
classic brick...
wich one is the 262 error. (why to put the error number? write the entirely error!)
Dunno if it is brick, because I cant update with most of the roms and also I get error with every radio I try to update with ... I've tried with more than 10 radio's from the archive ...
P.S. I think it is Hardware problem + I got brick and because of the hardware problem i cant reinstal rom+radio or rom to repair brick problem ...
So wich one is the error??????
error 206 207 200768 i dont know...i have this issues too and the cprog.exe seems to be incompatible ... my cable hasnt a good contact to the usb plus the rom i had i didnt downgrade to wmoriginal in a few times...
-Mobile MDA Vario II - help my screen is four colours
Hi I have the same phone a T-Mobile MDA Vario II i ran unlock program HTC_Hermes_SIM_CID_Unlock_v3a - i must have run it wrong or something cause my phone has colours on the screen red green blue white with the ipl 1.01and spl 1.40 - it used to ipl 1.4 (ithink) and spl 2.14(i think) before i tried to run the hct_herm.....v3a.
Is my phone trashed or what can i do . when i plug in the usb cable the message at bottom goes from serial to usb but thats it - the active sysnc does not see the phone. help help help any advice welcome ( short of buy a new phone) this is my new phone i only got it a day ago.
tks
hi guys,
trying to upgrade the radio rom, im using the customRUU and its getting to about 99% and then its getting the error 290: invalid command.
and now it only boots in the red, green, blue and white bootload screen.
heres some info if it helps:
SPL-1.42.HSPL on my hd2..
windows 7 home premium, (i tried running as admin, no difference.. also tried several other usb ports)
help would be appreciated!
thanks guys!
have you tried a good ol MTTY or Task29 before flashing?
does the phone boot to RGD screen?
what Radio you using?
And you have the phone HSPL unlocked?
dodgy download perhaps? tried another radio?
did anyone find the solution to this problem??
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
webiso said:
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
Click to expand...
Click to collapse
What exact ROM versions have you tried, and what SPL or HSPL do you have showing in bootloader? Also is there a radio currently on your HD2 and what is that radio if so?
normally phone hd2 leo and italy not t mobile ant spl 208 hardspl maked bootmode okay ( also write boot with jtag ) radio ver 2.15.50.14
webiso said:
l have same problem not upload any rom and radio tryed everything same eroor %8 and error 290 l dont know what is problem
Click to expand...
Click to collapse
I had the same problem. I was trying to restore my phone to original firmware, due to issues with custom firmwares. I had managed to extract the NBH from the installer provided by my carrier, and used CustomRUU to flash the phone, but the phone was not booting.
I then flashed one of the EnergyROM builds onto my phone.
After that I could not get the original firmware onto the phone, error 290 at 9%.
I booted my phone into the bootloader (red/blue/green), and used HSPL2 to set SPL to 1.42.HSPL. I could then flash the original firmware.
My phone is now working fine, as best I can tell.
Always showing bootloader screen with rom upgrade error
I was trying to revert to windows custom rom from android (due to frequent freezing) and then onwards booting the phone I am always getting the bootloader screen displaying rom upgrade error.
I tried hard reset but still the same problem persists, then I downgraded the HSPL 2.08 to SPL-1.42.HSPL and then tried reinstalling the custom rom but still the same problem persists. In between after downgrading the HSPL, I tried task 29, it was unsuccessful after 96% (shows Invalid Command (Error 290)), while reinstalling the customRUU I have, I got something like error 270 at the end (it goes fine till 100%).
I also tried with installing the radio (ver 2.15.50.14) in between but to no effect
Please help me in fixing the issue, my phone is of no use now