I was going to AT&t to try to get a replacement because the keyboard was very loose so I was flashing everything back after flashing the rom back I was flashing the stock hard spl but instead of replacing the nbh file I just put the file on my storage card and flashed it (VERY STUPID)
When I turn my phone on I get the tricolor screen and a message that says: Upgrade ROM code error Please try agian =
and nothing happens I tried hard reseting it but nothing happens, I can't get past that screen, I also tried flashing a new rom through the storage card method since I can't connect with Active Sync
Please help me , I just got my phone in November and I don't want to loose it, I would like to see what help I can get before going thought ATT customer service and telling them I didn't do anything and that it just happened by itself
Thanks to any people who respond
i think to flash a rom from pc u don't need to be connected to active sync try conecting while in tri clour screen and flash the rom
or could u say what exactly happened where u trying to flash a rom or what?
i tried now with my touch pro i entered boot mood then tried connected to pc to flash a rom and it worked it started.......
Thegreat1 said:
i think to flash a rom from pc u don't need to be connected to active sync try conecting while in tri clour screen and flash the rom
or could u say what exactly happened where u trying to flash a rom or what?
Click to expand...
Click to collapse
I was trying to restore the stock hard spl, don't
Thegreat1 said:
i tried now with my touch pro i entered boot mood then tried connected to pc to flash a rom and it worked it started.......
Click to expand...
Click to collapse
did u connect to Active Sync or through the storage card
no active sync
just entered boot mode then put the usb cable then started the flashing process
Thegreat1 said:
no active sync
just entered boot mode then put the usb cable then started the flashing process
Click to expand...
Click to collapse
I get an error during the flashing process, i was flashing the hard spl
read the first paragraph on the first post, I added exactly what I did wrong
u were trying to flash hard-spl when it hanged in the tri-clour screeen?
did u revert back to stock rom before trying to revert to stock spl?
Thegreat1 said:
did u revert back to stock rom before trying to revert to stock spl?
Click to expand...
Click to collapse
ya, read the my first post again, I added some stuff
Thegreat1 said:
u were trying to flash hard-spl when it hanged in the tri-clour screeen?
Click to expand...
Click to collapse
yes, after I messed it up the first time
if you can get to the boot loader screen you can probably flash any rom. simply rename the rom file to RAPHIMG.nbh and place it on your memory card, hold volume down + reset with stylus. you should be set. good luck.
does the bootloader still show the olinex 1.90
warren2781 said:
if you can get to the boot loader screen you can probably flash any rom. simply rename the rom file to RAPHIMG.nbh and place it on your memory card, hold volume down + reset with stylus. you should be set. good luck.
Click to expand...
Click to collapse
tried it, it doesn't work
Thegreat1 said:
does the bootloader still show the olinex 1.90
Click to expand...
Click to collapse
No, I am trying to flash it back to the olinex 1.90 but I keep getting an error in ruu
Have you tried this http://forum.xda-developers.com/member.php?u=467141
try flashing hard-spl once again. if it works your saved. as far as i know the people over at att only check for water mark at least in my place the y do. good luck
I found that it was not possible to flash the HardSPL from tri-colour screen.
It only worked for me when windows mobile was fully booted. When you start the HardSPL RUU the phone's screen will just go black, and will return when the update is completed.
I would try connecting the phone while in tri-colour mode, then running the original rom RUU on the PC and seeing if it works. If it gets to the stage where the loading bar shows up on the phone you should be ok.
Once the rom is loaded, start your windows mobile, connect to the PC, and run the RUU for HardSPL.
Best of luck to you!
Thanks for your guys responses I have successfully recovered my phone, I just flashed the original ATT rom from ruu
Very glad that you found solution to fix that problem, because it could happend to any one. Especially after I was thinking to flash everything back to att stock because of my usb exit is getting loose.
mr.denis said:
Very glad that you found solution to fix that problem, because it could happend to any one. Especially after I was thinking to flash everything back to att stock because of my usb exit is getting loose.
Click to expand...
Click to collapse
Thanks, ya, you just have to be careful and read directions if present and read them carefully
Related
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Please try the search button in this forum!!! And don't worry it's not bricked;-)
sayjeng said:
My dopod is on ipl/spl 2.20
while trying to update to the latest PV 4.0.0.0.6 Touch, i encountered an error..
Fine, reset the device, went to bootloader, started the PV_Temp upgrade file for my G3 dopod.
halfway, the update fails and says the NBF file cannot be used.
i've tried every other NVID rom and it is the same..
so now i'm stuck in the bootloader screeen and i can't do anything
Click to expand...
Click to collapse
check your .NET Framework and see if you have the 2.0 version installed. Reboot your pc and start again. We always experience these hiccoughs.
i've tried the search..
seriously saying, its quite hard to find what i want..
i seem to be able to flash the PV_TEMP ROM, it says on my computer its successful but my PDA just goes back to bootloader.
anyway, i'm installing .Net framework 2.0... will see how that goes..
still doesn't work..
RUU says its congratulations...
PDA goes back to bootloader
i cna flash jester's rom, i can flash PV_temps rom..
but all i get is the bootloader screen after that..
can't flash the NVID thats from the upgrade guide... it just says wrong NBF file..
wonder how much will it cost for me to send it to service center to replace the whole flash chip
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
sayjeng said:
new problem, now i can't do anything at all cause i think my batt is dead..
how can i recharge it ?
Click to expand...
Click to collapse
so you know now what is the problem!
recharge it by connecting to a PC with USB and wait wait wait and hope for the best. Try recharging it by what ever means you can do. If you said, you are successful in getting PVtemp, then, try installing battery_status.cab (find it search it by google or whatever) and watch the battery_status line on the front page and wait for a + sign before the 100mA at the right bottom line to appear.
Wait till it is full, then redo step 2 again. I'm sure you can get over without getting the machine to the manufacturer for repair.
no no
the first problem still stands
i'm still stuck at bootloader..
but now i can't flash anything cause my batt is dead..
so i've got 2 problems now
hello all,
sayjeng, I got the same problem last week.
I couldn't use any RUU rom because of the corrupted nbf file.
The PV_TEMP rom worked but I was stuck on boot loader screen too...
I tried many times and with some random hard resets... Eventually, the fourth time , WM5 started...
My advice are :
- charge your battery by any means like SeaPea said
- reboot your desktop computer
- remove your (fully charged) battery from your phone for some seconds and put it back...
Really, I may have been lucky that time...
I just wanted to post here to say that I sympathize...
Good luck!
will give it a try tomorrow..
its past 1am now and i need to be up early tomorrow..
if it doesn't, really have to make a trip to service center..
wonder what should i tell them then..
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
sayjeng said:
oh, forgot to mention
i can't hard reset..
i can get to the part where it says 'Press Send to restore factory default, Other keys to quit'
when i press Send, it says Format FAT Partition and followed by Format is Failed
then i get a flash for 1 sec of the vendor boot screen which is all green, and its back to bootloader
Click to expand...
Click to collapse
me too....any progress?
Jow ... flash your rom from dopod!
If your Radio Rom is crashed ... it stuck at Bootscreen too! After that it must run! it fix partition errors too.
ROm from dopod is 2.15..
my prophet is now on 2.20...
i can't flash it... i haven't been able to find a vendor rom wiht 2.20..
does anyone have any ? Qtek maybe ?
something to get my prophet running...
cause i did try in my attempt to get my prophet back by flashing the Radio ROM.. and it fails.. maybe thats why i can't boot my prophet
tried almost every rom..
used almost every RUU
anyone got any RUU that might help ?
or any suggestions ? thinking of throwing the towel and just pass it to dopod for them to handle....
worst case, change ROM chip
finally
I got this to work using the guide - BUT:
Windows XP SP2 English was the key for me.
I used VMWare to do step 1 of flashing (NVID)
then step 2 of flashing I did on a separate PC.
Worked after so many different attempts
i am running on XP sp2 english.. not using vista..
problem is, i can't even hard reset my phone.. it just says Format is Failed.
but my phone seems fine and still responds to my plugging the USB in and reseting....
Hi sayjeng
The same problem with my imate jamin too..
Whatever you said in you posts is an exact recall of my case.
Now it makes two of us
Waiting to see if someone can come up with a solution.
IPL/SPL at 2.20
Frequent automatic disconnection from activesync.
No means to charge the battery which i think is almost dead.
Tried the Dopod rom,for no avail.
The list goes on and on just like yours.
help..Anyone..?
Ok im not new to this flashing rom thing and ive been doing it for a while now but as of last night my phone randomly is rebooting i turn it on it works for a second and then reboots and then doesnt even get into the today screen just shows htc and reboots and reboots again i flashed to new rom did hard reset went back to original stock verizon rom and nothing any input would be awesome
bryanw17 said:
Ok im not new to this flashing rom thing and ive been doing it for a while now but as of last night my phone randomly is rebooting i turn it on it works for a second and then reboots and then doesnt even get into the today screen just shows htc and reboots and reboots again i flashed to new rom did hard reset went back to original stock verizon rom and nothing any input would be awesome
Click to expand...
Click to collapse
Try re-doing the bootloader. Sounds like a bad one. I've had that happen as well.
so should ijust reload hardspl 2.4 ? and then flash rom and what not ? cuz remember i cant get an active sync to run anything i can only get to the spl screen with the 3 colors it doesnt reboot there
bryanw17 said:
so should ijust reload hardspl 2.4 ? and then flash rom and what not ? cuz remember i cant get an active sync to run anything i can only get to the spl screen with the 3 colors it doesnt reboot there
Click to expand...
Click to collapse
hmm.... does it at least attempt an activesync connection? Does it stay in long enough? What I've done... is gotten RomUpdateUtility all the way to the last screen... and clicked next as soon as activesync sees it.
so.. i updated the hard spl and nothing it still restarts
bryanw17 said:
so.. i updated the hard spl and nothing it still restarts
Click to expand...
Click to collapse
Only suggestion left is to start over.... flash a different radio / rom... and then flash back.
did it twice i called verizon im getting a new one ty for the help tho
bryanw17 said:
did it twice i called verizon im getting a new one ty for the help tho
Click to expand...
Click to collapse
I take it you did a Lost / stolen phone? Or is it a replacement from verizon because it isn't working?
its under warranty so its free
Gotcha. I'm guessing they are making you send the old one back.
Hey guys, I havnt had a issue with my phone untill now, i installed energy rom a few days ago and i havnt had a issue however my ever my phone froze on me earlier so i poped out the battery and put it back in now it wont go past the splash screen, so ive tried to reinstall the at&t original rom and all and now i get the at&t splash but i get no where it just keeps reseting
Please Help!
sleepyzx said:
Hey guys, I havnt had a issue with my phone untill now, i installed energy rom a few days ago and i havnt had a issue however my ever my phone froze on me earlier so i poped out the battery and put it back in now it wont go past the splash screen, so ive tried to reinstall the at&t original rom and all and now i get the at&t splash but i get no where it just keeps reseting
Please Help!
Click to expand...
Click to collapse
Press and Hold the volume down key then push the reset button. When you see the tricolored screen, you can re-flash to a new ROM from there... just by launching a new flash.
thanks for responding yea i tried that i even reinstalled the energy rom but it still wont go past the splash
try flashing from you sd card, search flashing from sd card or something like that. I belive you have to format it in 32 mode and then take the rom "raphimg.nbh"(not exact spelling or proper spelling I beleive some of that has to be in capitals) sorry to here your phone is down. Try that and post your results.
Format the card FAT32. Place a rom on the card & rename the rom to RAPHIMG.nbh.
Put the SD Card in the slot & hold volume down & reset. Press the power button when instructed to do so on the screen.
thanks guys for ur help but i keep getting no image file then it says serial i formated the card and everything
sleepyzx said:
thanks guys for ur help but i keep getting no image file then it says serial i formated the card and everything
Click to expand...
Click to collapse
Try a different microSD. Also be sure that you did a full format not a quick format. I had an issue with a few microSD cards, but I like my 2GB PNY for flashing my phone via microSD.
I had the exact same issue after flashing the latest energy 3 rom
heres what i did
1. Reflashed Hard SPL
2. Flashed a stock HTC ROM, i managed to do this from my PC by manually entering the bootloader.
3. Did a hard reset
4. Let phone complete initial setup
5. Reflashed Hard SPL - Read somewhere that sock roms may overwrite \ partially overwrite Hard SPL
6. Flashed an Energy 2 ROM (only cause i wanted to check something out in it anyway)
So far its all looking good
sleepyzx said:
thanks guys for ur help but i keep getting no image file then it says serial i formated the card and everything
Click to expand...
Click to collapse
It happened for me with 2GB microSD. But magically after I did checkdisk/scandisk, the image found
shearsey said:
I had the exact same issue after flashing the latest energy 3 rom
heres what i did
1. Reflashed Hard SPL
2. Flashed a stock HTC ROM, i managed to do this from my PC by manually entering the bootloader.
3. Did a hard reset
4. Let phone complete initial setup
5. Reflashed Hard SPL - Read somewhere that sock roms may overwrite \ partially overwrite Hard SPL
6. Flashed an Energy 2 ROM (only cause i wanted to check something out in it anyway)
So far its all looking good
Click to expand...
Click to collapse
This look like some dangerous steps
Let me ask you guys, which version of Energy are you guys using?
monx® said:
It happened for me with 2GB microSD. But magically after I did checkdisk/scandisk, the image found
Click to expand...
Click to collapse
good to see you back, ive had similar issues with a my 16GB and 8GB aswell a few times i think its due to some corruption beeing made to the filesystem when we disconnect it to soon form the pc (using it as disc-drive) thats kinda the same thing that happens when u disconnect a usb-harddrive in windows while its in use by windows and tries to connect it with linux.
a really good disc-repair tool i stumbled upon is located here
http://www.cgsecurity.org/wiki/TestDisk
and just to make sure its done right as gsleon3 said, do as he said and make sure that you take the you take the ruu_signed.nbh and rename that to raphimg.nbh (not sure if it has to be in CAPS, im pretty sure ive done it like this RAPHimg.nbh lots of time)
...monx, it would be great to have you back cooking wonderful stew
cheers
@jonteponte
thanks for the tool. it is not case-sensitive but name-sensitive
i'm not going anywhere. always around
-freeheel is freedom, tried, i love it
monx® said:
@jonteponte
thanks for the tool. it is not case-sensitive but name-sensitive
i'm not going anywhere. always around
-freeheel is freedom, tried, i love it
Click to expand...
Click to collapse
@monx® you're welcome
if you ever come to the northern part of sweden just let me know and ill take you on trip, i have several pairs of skis and boots aswell =)
I'm stuck on the screen that says SPL-1.20.01 Olipro did I brick it ? please help!
No, it is not bricked. You should just have to flash the Titan Unlocker, refer to this thread->http://forum.xda-developers.com/showthread.php?t=423177
That should get you going. After that you will need to flash a rom with radio.3.4+ (perferably 3.42.50), or flash the radio, then flash the rom.
If that doesn't resolve your issue just search for Titan Relocker
Thank you !! greatly appreciate it trying it now
theintrospect said:
No, it is not bricked. You should just have to flash the Titan Unlocker, refer to this thread->http://forum.xda-developers.com/showthread.php?t=423177
That should get you going. After that you will need to flash a rom with radio.3.4+ (perferably 3.42.50), or flash the radio, then flash the rom.
If that doesn't resolve your issue just search for Titan Relocker
Click to expand...
Click to collapse
Dude I dont want to be mean to you but I have noticed the past couple days you jumping right in.. With knowledge or not.. What are you trying to do? Your answer is wrong as the User states that he is stuck in bootloader, to flash a bootloader needs to be done from a functioning OS.. Also by the looks of his bootloader it was never unlocked so how could he use the re-locker?
There are far more steps then just flashing an unlocked bootloader from where he is at in stuck bootloader. He may need to run ExitBootloader before trying anything depending on if he can reset the phone and it doesnt go right to bootloader (that would mean stuck bootloader)
Hint * Exitbootloader fix (if stuck in bootloader meaning even a reset will not get out of it), then Branded Carriers Stock ROM (User should know if it was GPS or not), then Olipro 2.40 Unlocked bootloader, then Custom ROM and GPS Radio.
Thank you Ryan ! I'll search for exit bootloader now ...
suhas2000 said:
Thank you Ryan ! I'll search for exit bootloader now ...
Click to expand...
Click to collapse
Here I cringe and wince to have to post this link at ppc dorks but its the first thing I found with easy instructions. Read the part about the titan, disable usb connections by right clicking active sync icon in taskbar and then plug the phone in after putting into bootloader (i know its stuck, just do it anyways, power + camera + reset button for couple seconds) Then run the Exitbootloader.
http://forum.ppcgeeks.com/showthread.php?t=9229
Then from there follow my previous instructions, you need to put the Stock ROM back on the phone whatever carrier its branded to. Then while in the Stock ROM's OS re-enable active sync connections and plug the phone in and make sure its synced and working properly. Then flash the Olipro 2.40 bootloader. Then while the phone is still in the olipro 2.40 bootloader flash the Custom ROM you want to use and then the GPS Radio. Perform a hard reset and pull the battery for a couple minutes. Then you should be set to jet.
Ok I think I rushed into it without waiting for your advice & now I'm out of the first screen but stuck in htc mobility/ no radio screen.. wtf ? am I that dumb ?
It keeps saying that my device is not connected to the PC... I made sure about the USB option in active sync & stuff... pls help
suhas2000 said:
Ok I think I rushed into it without waiting for your advice & now I'm out of the first screen but stuck in htc mobility/ no radio screen.. wtf ? am I that dumb ?
Click to expand...
Click to collapse
Make sure you are using Active Sync 4.5 and not using a Hub. Make sure to plug the USB cable into a main port on the PC. While the phone is unplugged. Manually put the phone in bootloader (power + camera + reset "little hole near memory card slot" buttons for couple seconds and release), make sure the active sync usb connections are disable from active sync connection settings on your PC's taskbar. Then plug in the phone (while in bootloader in to computer) and flash your Stock Branded Carriers ROM by running the Rom Update Utility EXE, RUU or exe however it comes. Once that is done you can unplug the Phone and let it boot up customize and all. Then re-enable the active sync usb connections in connection settings (PC Taskbar Active sync icon) and plug the phone in. Should sync up. Icon will turn green. Now flash the Olipro 2.40 bootloader and let it do its thing make sure to pay attention. When it is done it will still be in bootloader, then you can go ahead and flash your Custom GPS Titan ROM and GPS Titan RADIO followed by a hard reset and battery pull for a couple minutes.
You're a great teacher.. awesome step by step instructions... after all this, I think I'm gonna stick with the stock ROM ... so much for the flashing & all that !
I'll keep you informed about the progress .. thanks a million !!
It did it again ! at 11 % it stops & goes back to that original SPL 1.20.Olipro screen what am I dong wrong ? I feel such an idiot !
suhas2000 said:
You're a great teacher.. awesome step by step instructions... after all this, I think I'm gonna stick with the stock ROM ... so much for the flashing & all that !
I'll keep you informed about the progress .. thanks a million !!
Click to expand...
Click to collapse
No problem, well if you stay with the stock ROM stop before the Olipro 2.40 bootloader. That is for GPS ROM's only.
So if you are a little nervous and wish to remain stock follow my instructions up until the Olipro 2.40 part.
If you wish to continue and go the Custom ROM route thats up to you. Just remember if switching Carriers you need to Load PRL, Do PST and QPST settings. Plus the Custom ROM may need a Carrier CAB installed and registry edits for MMS. With my Custom ROMs you do not need Carrier cab or registry edits (but you still need to do PST/QPST and PRL) . I have 5 carriers to choose from right now for example.
suhas2000 said:
It did it again ! at 11 % it stops & goes back to that original SPL 1.20.Olipro screen what am I dong wrong ? I feel such an idiot !
Click to expand...
Click to collapse
If you are using Windows XP, Try installing these drivers to your Computer, restart your Computer, make sure you are plugged in to only a main port on the pc, unplug every other usb device just to make sure. and go over the steps again. You may need to pull the battery and let it sit for awhile, then put the battery in (do not power up) and charge for a little bit. Then try again.
Thanks for your patience ..greatly appreciated !
suhas2000 said:
Thanks for your patience ..greatly appreciated !
Click to expand...
Click to collapse
No problem, I am pretty sure the Stock ROM you need to flash has to be NON GPS as per the bootloader that is on there now. Just making sure you know that.
Ok all I want is to get the GD my sprint stock 3.56 ROM back on.. but it only goes till 11 % & stops ..what the hell am I doing wrong ? Ryan you don't understand how much I admire your patience with dummies like me !
suhas2000 said:
Ok all I want is to get the GD my sprint stock 3.56 ROM back on.. but it only goes till 11 % & stops ..what the hell am I doing wrong ? Ryan you don't understand how much I admire your patience with dummies like me !
Click to expand...
Click to collapse
Try an earlier NON gps stock sprint ROM.
I'm so sick of looking at that SPL 1.20 screen... lol can we start from scratch again pls ? I know it is annoying
I tried to flash to sprint stock 3.35 which is the older 6.0 rom.. still it too stopped after 11% ... what's the matter ? Ryan pls help !
suhas2000 said:
I tried to flash to sprint stock 3.35 which is the older 6.0 rom.. still it too stopped after 11% ... what's the matter ? Ryan pls help !
Click to expand...
Click to collapse
3.35 is still GPS. You need the NON GPS Sprint ROM.
Hey, i tried to install android on my HD2 several times and failed, but then i noticed i had wrong version of hspl so i couldn't start MAGLRD (i had 3.03 i think i should've had 2.08 right?) Anyway i then tried to remove the HSPL by formatting my sd card and putting the file from original rom (i don't remember the name) and renaming it to LEOIMG, it started installing the rom i went to another room, when i came back it had finished and was on the red/blue/green screen and it said update failed and i had to retry, but now none of the exes work like rom updates or task29 nothing. when i turn on the phone it says "Not allow" and then goes to the red/blue/green screen. Please help me, I'm freaking out is there any way to fix it? Is there even a way to access SD card when the phone does this?
TomaToz, use the computer to flash via USB cable.
I can't, none of the rom updates or ANYTHING works since this, they all give errors
go to the magLDR page and look for how to remove it.
then start from scratch
There's no info how to remove it but even if there was how would i? None of the exes work and i can't turn the phone on, also i dont think MAGLRD got installed cause i had HSPL 3.03 instead of 2.08
Come on isn't htere anyone who ca help me? :|
are you sure you haven't bricked your phone?
because it just seems you did :/
I don't think you read the bold "You need HardSPL 2.08 before installation!" just above the history?
anyway, can you not flash a radio via USB as well?
also, if you post the error messages you get maybe we can help you more.
you can also check here:
http://forum.xda-developers.com/showthread.php?p=10275463
What does bricked mean? :9
and no i can not flash radio or anything else, i'll edit this message with a picture of what the error message looks like
EDIT: WOW, i tried to run the hspl installation and installed hspl 2.08 successfully, not i turned my phone on and its the screen where you choose to start the update for rom. This is the update after which my hd2 said "Update failed" so I'm scared to take any steps, please respond and tell me what to do
HOLY FREAKING CRAP! I installed android and everything seems to work fine, i can't tell you how relieved i am :]]]]
That's for your attention
Does anyone know where to get apps for Android 2.3.2?
What i installed is TyphooN_CM7_v3.5.9-MAGLDR
Help please!!! Hd2 stuck !
HI to all!my phone was working great until i decided to try a new rom so I installed task29 (i had elegancia rom but i wanted to try another rom)and now im stuck on the htc logo screen that says 'stick together' in a red square.....i tried vol down+power button to go into bootloader but nothing happens, then i tried to hard reset but still nothing happens...i pushed the reset button and i did it all over again at least 3 times but still nothing... is there anything else i can try? (even on the hardware?)
my HD2 is a T-MOBILE usa with :
radio 2.08.50.08_2
2.08.HSPL
3.14.531.1 elegancia rom(http://forum.xda-developers.com/showthread.php?t=651729)
i love my hd2 and i want it back...PLEASE HELP!!!!!!!
THANK YOU in advance!!!
sofialoca, task29 is not a thing to be "installed". It's a flash formatting. So you did everything correctly and deleted all from your phone except.. hmmm... stick together.
To flash other rom - just press Volume Down and push reset (under the battery cover) KEEPING VOLUME DOWN PRESSED. Keep it pressed until you are again in bootloader mode. Then connect USB and flash whatever you want.
thank you Andrew!I found the problem...
AndrewSh said:
sofialoca, task29 is not a thing to be "installed". It's a flash formatting. So you did everything correctly and deleted all from your phone except.. hmmm... stick together.
To flash other rom - just press Volume Down and push reset (under the battery cover) KEEPING VOLUME DOWN PRESSED. Keep it pressed until you are again in bootloader mode. Then connect USB and flash whatever you want.
Click to expand...
Click to collapse
thank you so much for the quick response! the problem was with my volume down button...i opened up the phone and moved the flex ribbon a bit to get it into place .after that it got in bootloader mode succesfully!im now back with elegancia and never gonna change it...i think i got a little greedy...afterall elegancia rom is great!thank you Miri and Steve0007 for this great rom and thank you again Andrew!
TomaToz said:
HOLY FREAKING CRAP! I installed android and everything seems to work fine, i can't tell you how relieved i am :]]]]
That's for your attention
Click to expand...
Click to collapse
glad it worked out in the end