Touch Pro Bricked??? Please tell me someone can help!! - Touch Pro, Fuze ROM Development

Touch Pro Bricked
Ok so I am a noob and at least I admit it!!! I had been having problems with the display scrambling on my flashed to cricket sprint touch pro so what I did was install Hardspl 37 and tried to do a new flash. I last saw my display say that a problem occurred while flashing to the new rom and now I get nothing when I power up. I have tried hard reset I have tried soft reset I have tried about a million different key combos and I get nothing just the backlight pops on and nothing beyond this point. I get nothing when it powers up ...no startup sounds nothing...Just the backlight pops on and then nothing PLEASE HELP!!!!!!!!!!!!!
IS THIS PHONE A 300.00 paper weight???
Ok so Heres what I have done.... I started the flash from my pc but it didn't take so then I put hard spl 37 on my sd card along with raphimg.nbh and since then I get nothing like I stated above??? also bootloader wont come up the phone powers up but doesnt vibrate like it used to and I get just the backlight??? Some one on another site said to try to manually get into bootloader but I don't know how any suggestions would be greatly appreciated.

Should try pressing volume down button while reseting till you get to bootloader. If not, then...

Oh, and hardspl you want to use is ver 1.90 by Oli Nex. Not sure which one you used.
see bellow
http://wiki.xda-developers.com/index.php?pagename=Raphael_HardSPL
Another thing that might have caused this is flashing gsm rom on cdma device (which is your case I suppose - Fuze). Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).

To get into boot loader hold down the vol down key while turning on the phone.
Best way for you to try is to take out the battery, put it back in, hold down the 'volume down' button on the side and press the power button.
Sorry that's all i can help you with. Hopefully someone else has had this happen and knows a way out of it

lindenny50 said:
Touch Pro Bricked
Ok so I am a noob and at least I admit it!!! I had been having problems with the display scrambling on my flashed to cricket sprint touch pro so what I did was install Hardspl 37 and tried to do a new flash. I last saw my display say that a problem occurred while flashing to the new rom and now I get nothing when I power up. I have tried hard reset I have tried soft reset I have tried about a million different key combos and I get nothing just the backlight pops on and nothing beyond this point. I get nothing when it powers up ...no startup sounds nothing...Just the backlight pops on and then nothing PLEASE HELP!!!!!!!!!!!!!
IS THIS PHONE A 300.00 paper weight???
Ok so Heres what I have done.... I started the flash from my pc but it didn't take so then I put hard spl 37 on my sd card along with raphimg.nbh and since then I get nothing like I stated above??? also bootloader wont come up the phone powers up but doesnt vibrate like it used to and I get just the backlight??? Some one on another site said to try to manually get into bootloader but I don't know how any suggestions would be greatly appreciated.
Click to expand...
Click to collapse
Step 1. Take a deep breath
Step 2. Search and read... sounds frustrating buts lots of devices have been brought back from the dead.
Step 3. Get the phone to bootloader mode (three horizontal color bars)
Step 4. Read some more or read other posts on what to do because I can't help past this!
I think you may have used the wrong SPL so start looking there.
I saw what Bauerpavel just posted... good stuff
If you can get to bootloader mode you should be able to start all over again from here
http://forum.xda-developers.com/showthread.php?t=448008

If you're running a Sprint Touch Pro, most of the roms here are not for your phone. May want to try ppcgeeks.com

bauerpavel said:
Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).
Click to expand...
Click to collapse
Just to be clear, not to be confused with the AT&T HTC Fuze, which is a GSM device!
But you're with Sprint, so assuming you're in the US, you have a CDMA device. Check the CDMA forum at the top level of the Raphael forums. There will be lot's of good advice there on the specifics for that hardware.
Good luck!

bauerpavel said:
Oh, and hardspl you want to use is ver 1.90 by Oli Nex. Not sure which one you used.
see bellow
http://wiki.xda-developers.com/index.php?pagename=Raphael_HardSPL
Another thing that might have caused this is flashing gsm rom on cdma device (which is your case I suppose - Fuze). Make sure that rom you are flashing is for your device (either raphael (gsm) or fuze(cdma) ).
Click to expand...
Click to collapse
Fuze=AT&T=GSM
Sprint TouchPro = CDMA
If you tried flashing a GSM ROM to a CDMA phone you may be up the creek!

Related

Hard-SPL, Or How to Not Brick Your PDA Ever Again

Right, This is the basic Hard-SPL package; if you already have applied Hard-SPL with the unlocker then DO NOT BOTHER TO USE THIS PACKAGE.
This program is now foolproof as the SPL is flashed directly from the bootloader rather than from the OS so there's no opportunity for anything to go wrong.
for this to work, your device MUST BE RUNNING WINDOWS MOBLE and MUST BE SYNCED WITH THE PC.
to recap: IF YOU ALREADY HAVE 1.20/1.25, DO NOT USE THIS.
Thank you! I won't be waitin', though...
Whatever Trevor.
laikos said:
Hi I'm trying to downgrade to Hard SPL 1.1olipro to try to restore Factory SPL (Hoping that it will fix my WLAN Dead issue) however I can't seems to downgrade from IPL 1.04 + SPL 2.10.0lipro
I've followed the instruction from http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=59&Itemid=27
and I keep getting [error 260] Anyone knows how to get around this?
Thanks
Click to expand...
Click to collapse
it WILL NOT fix your dead WLan.
secondly, don't start spamming other threads by crossposting. Idiot.
Olipro said:
it WILL NOT fix your dead WLan.
secondly, don't start spamming other threads by crossposting. Idiot.
Click to expand...
Click to collapse
With all due respect I don't mean to SPAM neither crossposting, anyway I've make mistake by putting the device in Bootloader mode when I'm trying to downgrade the SPL. Yea I figured out it will NOT FIX the Dead WLAN either. Sorry for the inconvience
How do I go backward on my SPL
I upgraded to SPL 2.10, but my touch screen keeps failing, I f I leave the battery out for 30 min to an hour the touch screen works for about 30 min then goes touchless. I need to go back is it possible.
DRACO00 said:
I upgraded to SPL 2.10, but my touch screen keeps failing, I f I leave the battery out for 30 min to an hour the touch screen works for about 30 min then goes touchless. I need to go back is it possible.
Click to expand...
Click to collapse
The SPL has nothing to do with it.
Also, this is the Athena forum, so piss off.
DRACO00 said:
I upgraded to SPL 2.10, but my touch screen keeps failing, I f I leave the battery out for 30 min to an hour the touch screen works for about 30 min then goes touchless. I need to go back is it possible.
Click to expand...
Click to collapse
Take out the plastic cover and THEN try ))) I kinda keep hearing that a lot and this "fix" fixed a lot of those...
AThena broken, any help ???
Problem_Description: Hello,
My Athena bought since last may si out of order because i ve tried to install english rom for WM6 instead of the french one !!!.
I realise that a big mistake but how can i make it starting again, it's blocking in the wm6 upgrade screen ???
I ve tried to make hard reset to restore default parameters but no resultat and the original rom is dammaged and however has erased.
MS activsyn can'nt connect to the device because of no wm system is reconized ....
I'm waiting for your help because I can't work without Athena !!!!
Nothing work (tried soft reset or hard reset) but only a 3 colors screeen and no more ...
I m reelly sad and i'm wainting for your help.
Olipro said:
OK... just to make this clear.
Go to the Athena forum and download the unlocker; do Step 1 to flash Hard-SPL.
after that you can close the program if you don't need to unlock.
if I come out with new releases of Hard-SPL, the package will be posted here.
Click to expand...
Click to collapse
Have you used Olipro's unlocker before?
All theree steps ?
Can you enter the Bootloader Mode?
hey olipro! nice work i have a htc advantage x7500 and i try to hard spl it but it's not working!!! at the Step 1 when the cab was copied to the device i've installed it but my device was working and it hadn't gone idle!!! what can i do now? could you help me?
oh GOD i think i brick my device!!! i install RUU_Athena_DOPODASIA_WWE_2.19.707.4_1.45.00.10_Ship without doing any of the steps and now it's like this can anyone hel me????
Unlocker for x7501?
Is this unlocker suitable for the x7501 WM6 unit as well? Also do you still need to flash the SPL on the x7501?
Lastly what is "SPL" and why can you brick your device if you don't carry out this upgrade?
simonsalo said:
Is this unlocker suitable for the x7501 WM6 unit as well? Also do you still need to flash the SPL on the x7501?
Lastly what is "SPL" and why can you brick your device if you don't carry out this upgrade?
Click to expand...
Click to collapse
try reading around to find out. or did you think I was bullshitting. I'm struggling very hard not to insult you for your laziness.
Advantage Problems
-----------------------DO NOT USE UNLOCKER ON UNLOCKED HTC 7501 ADVANTAGE ------------------
Oli,
I have (had) a brand new unlocked 7501 Advantage. I followed your unlocker advice above to do step 1 very carefully and now have a bricked device after I saw the same error trying to backup my SPL file like others. Can you place a big bold warning on your SPL Flash link so that other people may not see the same fate...from reading the comments on this thread we are lead to believe that you suggest that we should flash to your SPL before trying a cooked ROM on the 7501 Advantage...
TIA
-Lol! Some big Advantage, now Im out 900 bucks !
photon2 said:
Oli,
I have (had) a brand new unlocked 7501 Advantage. I followed your unlocker advice above to do step 1 very carefully and now have a bricked device after I saw the same error trying to backup my SPL file like others. Can you place a big bold warning on your SPL Flash link so that other people may not see the same fate...from reading the comments on this thread we are lead to believe that you suggest that we should flash to your SPL before trying a cooked ROM on the 7501 Advantage...
TIA
-Lol! Some big Advantage, now Im out 900 bucks !
Click to expand...
Click to collapse
If you can get to bootloader, there might be hope yet. Follow this solution , if you can
http://forum.xda-developers.com/showthread.php?t=326953
Still no luck- been trying all day but nothing - not able to see anything except red LED lit up around the joystick when I am on AC and the battery is removed.
I am going to try warranty repair but probably am out of luck
photon2 said:
Still no luck- been trying all day but nothing - not able to see anything except red LED lit up around the joystick when I am on AC and the battery is removed.
I am going to try warranty repair but probably am out of luck
Click to expand...
Click to collapse
Are you able to get into bootloader? If I read correctly the answer should be no but I wanted to confirm either way. If no, how have you tried to get into bootloader? Key sequence in other words? Have you removed the SD card also?
You are correct, I cannot seem to get into the bootloader or even get the device to come alive at all. I tried camera + reset, volume down + reset, volume down + camera + reset, I looked all over the forum and found a few others but still no luck. All I see is the red LED around the Joystick either become solid lit (without battery in and on AC) or blink lit (with battery in and on AC). The light stays solid lit with battery out and all key combinations tried and does the quick blink lit with battery in and all key combinations as long as reset is pushed. Basically, it would seem that the reset key is working by resetting the circuit to the battery but the device just wont boot up.
I will be sending this unit back anyway due to a manufacturing defect of the SD card slot. When this particular unit was built, I guess no one actually checked to see if the a (mini not micro) SD card fits in, cause IT DON'T!! The slot was missed by about 2mm being to narrow in width...GEESH!!
I am not too happy with hardware of the 7501 right now and probably will look at getting the 7500 or Dopod version for "cooked ROM" pleasure but my advice to others reading this would be to not run out and get the 7501 at the lower price given the problems I am seeing. However, on a positive note, the few hours I did get the 7501 running, it was a blast and I still give the overall performance a 4.5 out of 5 star rating being the most complete and fastest PDA Phone I have had the pleasure to work with.
photon2 said:
You are correct, I cannot seem to get into the bootloader or even get the device to come alive at all. I tried camera + reset, volume down + reset, volume down + camera + reset, I looked all over the forum and found a few others but still no luck. All I see is the red LED around the Joystick either become solid lit (without battery in and on AC) or blink lit (with battery in and on AC). The light stays solid lit with battery out and all key combinations tried and does the quick blink lit with battery in and all key combinations as long as reset is pushed. Basically, it would seem that the reset key is working by resetting the circuit to the battery but the device just wont boot up.
I will be sending this unit back anyway due to a manufacturing defect of the SD card slot. When this particular unit was built, I guess no one actually checked to see if the a (mini not micro) SD card fits in, cause IT DON'T!! The slot was missed by about 2mm being to narrow in width...GEESH!!
I am not too happy with hardware of the 7501 right now and probably will look at getting the 7500 or Dopod version for "cooked ROM" pleasure but my advice to others reading this would be to not run out and get the 7501 at the lower price given the problems I am seeing. However, on a positive note, the few hours I did get the 7501 running, it was a blast and I still give the overall performance a 4.5 out of 5 star rating being the most complete and fastest PDA Phone I have had the pleasure to work with.
Click to expand...
Click to collapse
Man that sucks. Seems like you've tried the correct combination of keys to get into bootloader...just make sure you were pressing that camera button firmly because it's known not to take unless you do this.
What operating system is on your computer BTW? Windows XP/Vista?
I'm not sure I understood the problem with the SD Card. Do you mean to say that when you tried to put in a mini-SD card (not Micro), it wouldn't fit into the slot?

Blank bootloader...am I screwed?

I have searched and searched these forums and have seen several other people with this problem but no solution. I have also looked through the wiki to no avail, so if someone can give me an answer I would really appreciate it.
I have been able to get into the bootloader screen (the r-g-b white stripes) however there is NO text (no serial, no usb) on the screen and it is not recognized by any pc. Can't get any response from mtty.exe because it can't see the USB port. Have tried on multiple PC's...
Is there another way to resurrect this athena or is it DOA?
Thanks,
-Alex-
Some pics of problem...
Blank bootloader...
Please help!
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
jas_pik said:
Did you try reflash by SDcard?
http://wiki.xda-developers.com/index.php?pagename=Athena_SD_Card_Flashing
Click to expand...
Click to collapse
Yes...no joy.
Just stays on the tri-color screen with no indication that it is reading the card.
Thanks for the advice though!
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
ssutherland said:
Did you try resetting - camera button and reset button on the back (I think...) pressed together.
Forum search will tell you exactly...
Click to expand...
Click to collapse
Yes, tried the hard reset (camera + reset) the alternate reset (comm + camera + reset) and even the other reset (volume slider + camera + reset). And yes, I was pushing down firmly on the camera button.
Each reset brings me to the tri-color bootloader screen with NO text. No model number, no OS version, no "USB" / "Serial"....just the red-gree-blue-white stripes.
I have looked extensively at all the forums, used the google search for the site and combed the wiki with no luck.
So do you think it is a lost case?
-Alex-
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
luthor_70 said:
Hello,
sorry for what's happening to you. Can you tell what led to this situation ? Were you trying to unlock your phone or just flashing a new rom ?
Click to expand...
Click to collapse
I was trying to load a new ROM but I assumed that I had to use the OliPro unlock first.
Got to the radio flash and that is where it crapped out.
Now that I have read a little more carefully it looks like I don't need to use the OliPro beyond the first step for the stateside unlocked 7501.
Thanks,
-Alex-
when your on bootloader ? does windows detect a usb generic device ?
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
bairda said:
Nope. Tried 3 different PCs. Shut down all the activesync processes. No luck. No detection that anything is cabled to the advantage.
I am thinking that it is warranty time.
Damn, I hate this....its just the principle of the thing...
-Alex-
Click to expand...
Click to collapse
Key rule to remember is to always make sure the Advantage is Fully charged. Try charinging it and reflashing it with the factory rom, located here. http://www.america.htc.com/download/RUU_Athena_HTC_US_2.19.453.4_105_1.47.51.00_Ship.exe. Keep us posted and let us know how it went
have you removed the sim and memory card
just checking basics
try that with a full charge and then enter bootloader and connect to usb
Thanks for all the help! I gave up and warrantied a new unit where I WAS successful in loading a new ROM.
I have learned several valuable lessons in the ROM upgrade process. This was on an advantage 7501, unlocked, USA version. I did the upgrade the process with the OliPro 3.0 unlocker, the PK Rom 3.0 and vista pro (32bit):
- Make sure that you have NOT customized your athena/advantage beyond the basic calibration and cut/paste walkthrough.
-Download ONLY THE MOST RECENT VERSION OF THE OLIPRO UNLOCKER. CHECK TWICE TO MAKE SURE THAT YOU HAVE THE LATEST.
-You MUST let step one of the Unlock complete. With the latest version this will make a bricked Advantage practically impossible.
-Go through step 2 & 3 even if you don't think you need this. It will upgrade the radio and give you peace of mind if you are updating to the PK rom.
-Don't panic if you complete step 1 and goof step 2/3. You can recover. But if you screw up the initial SPL unlock in step1...it is not going to be pretty.
Hope this helps!
Thanks for everyones advice!
-Alex-

Fully Bricked Raphael

Hello ,
my HTC Touch pro was bricked few months ago
i installed WRONG hard spl
on pc it showed 100% Completed
but i couldnt start my phone
how can i fix this ?
if i use Hard Reset method, i doesnt work , i cant start my phone
have you tried installing a new SPL via storage card (rename spl file to RAPHIMG.NBH and place it on the storage card) and enter bootloader mode by holding the vol down button when powering on the device?
the problem is
i cant start bootloader
nothing is working
I think you got yourself a brick...
Does it at least vibrate?
Run SPLExploit!
Dude, i have the same problem with you too but its not my TouchPro but its my old school Dopod D810. I flashed custom rom (my home cook) but forgot to add sumthin and finally i learned somethin that i can ****up my phones LOL. Just like what i thought my phone wont start and it refuse to enter on Windows OS but atleast bootloader mode still accessible. Thanks God
I search for post how to recover bricked phone (ofcourse on trinity room) and found some tools call "SPLEXPLOIT" it runs on DOS Mode. This program can erase your nand memory which in this case you flashed the wrong SPL and will rebuilt some bad Nand memory too. Good tho
I finally can bring my dead dopod came to life (for almost 1 year i left it on garage) lol. Just asked cmonex! maybe he can help you...
If this tools works universal i'm sure it will worked on TP too! Just asked cmonex for more details...
Run SPLExploit (as Administrator) --> while Enter in Bootloade mode -->
Just make sure that USB Cable was recognized as "USB" on the bottom of the screen not "Serial"!
When its done ....
NOTE: "Dont Soft Reset the phone even when SPLExploit ask you to SR the devices" just go ahead straight away flashing new custom rom or anything you want
Goodluck!
The OP can't get into bootloader, because the bootloader is corrupted/dead. So that isn't going to work.
JTAG is the only way to fix it, and as far as I know, no one knows how to do it on a Raphael.
Maybe playing with BIOS ( if BIOS can be accessed ) might help.
But BIOS can really make ur brick a worse brick if done wrongly please ask for help from the senior most members on Raphael forums.
And request them don't order them.
And if nothing works * I love to say this line *
You Just got Yourself a New Shiny Fine Edged Black Clear 600 U.S. Dollars worth Of a BRICK ! Enjoy !​
atjee said:
the problem is
i cant start bootloader
nothing is working
Click to expand...
Click to collapse
Do you tried to start bootloader manually?
You can do that, press and hold Vol down, then reset button (with stylus), release reset (keep vol down pressed) and when the multicolor screen appears then release vol down key
I hope this can help you?
iugalde said:
Do you tried to start bootloader manually?
You can do that, press and hold Vol down, then reset button (with stylus), release reset (keep vol down pressed) and when the multicolor screen appears then release vol down key
I hope this can help you?
Click to expand...
Click to collapse
That is the only way to go to bootloader but as Farmer Ted mentioned his phone ( including bootloader is dead ! )
So i don't think there is any way out for you except if any really senior members can help you with bios or pump in something which starts your bootloader !
atjee said:
Hello ,
my HTC Touch pro was bricked few months ago
i installed WRONG hard spl
on pc it showed 100% Completed
but i couldnt start my phone
how can i fix this ?
if i use Hard Reset method, i doesnt work , i cant start my phone
Click to expand...
Click to collapse
Dude, you might try to PM cmonex. I hear she can do miracles. You can check out this thread and see a miracle there. Who knows? See what can be done. This link will take you to her contact page: http://forum.xda-developers.com/member.php?u=322932. Best of luck to you my friend. Worst case scenario, sell it for parts. Several people around here are always looking to replace "stuff", including me .
the same problem
I did the same thing to my HTC Fuze aka rafael or touch pro, from some reason it was the same thing as diamond and i flashed wrong spl and completely bricked it, no bootloader no nothing. So i went to a service and they said it was a hardware problem so they had to send it somewhere else to be fixed. It took them 3 weeks to get the phone back, in not working condition saying that motherboard was dead. I guess thats what happens when you flash wrong stuff... Now i dont know what to do either. I would like to sell mine for parts if someone is interested or if someone know how to use jtag i would pay him to try to fix it...

HD2 is brick not boot up Please help

First of all sorry for my english not good.
Start : with my HD2 have brick after task29 and not success to flash new ROM I'm take USB. cable out and try to open my HD2 in to boot loader by put volum down + power bottom but screen not show any image or 3 color my phone it only long vibration pull battery out waiting 30 minute and put battery in and try to open my phone to boot loader but is same only long vibration.
Now : can not do any think with it when try to plug power in my phone is auto startup and long vibration.
I'm search on google and in this forum not have some one face problem same as me please help me to fix this.
Any body please help me, I'm love it because now we can run both WM. and Android
Upppp waiting for your help
Did you try a long press of the reset-button?
You could try to put the original Stock Image from HTC onto the root-folder of your SD-Card, rename it to LEOIMG.nbh and Push Vol up + Vol down during start and follow the on-screen instructions if it works.
Otherwise use Search-Function in the forum.
ı have jtag HTC for samsung and HTC devices if u want send for repair to me..
www.sevgigsm.net/forum
admin..
I use ORT
Did you check to make sure your radio version was correct before flashing? This is probably the number one reason for bricking.
Check this thread it may help you if you did the flash properly:
http://forum.xda-developers.com/showthread.php?t=668347
i got same problem now...
no screen, no boot, vol down+ power oso same
no screen just a long vibration
anybody help?
I am using the correct radio so don't tell me I am using a wrong radio or something, I have been flashing for 4 months so I know EXACTLY how to flash.
now i can neither get into tri-color or hard reset so don't tell me to flash or smth like that, just tell me how to recover properly
Don't tell us to use search or something because seems like only 2 of us is encountering this problem in the internet
I'm exactly the same problem as TS coz it juz auto go vibrate when plug in battery
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
at the long vibrate, when i plug in to my pc, it will keep on got usb connected and disconnected sound
and dont know what device is connected as not shown in found new hardware and device manager
I also have been searching all possible keywords about what me and TS encountered but all linked to completely UNRELATED results(like search for long vibrations only link to people asking how to make vibration long and 1st result is this thread)
bountygiver said:
This problem actually started when I flash ROM halfway, it stucked and failed...
the device is already HSPL-ed!!!!
but why the F it cannot get into tri-color bootscreen now?
Also, I have to state that my device already got several problems before, my device was very hard to bootup as it will always stuck at HTC screen w/o red version number at bottom left corner, must keep on removing and reinstall battery and reboot until it can boot, not an issue with rom/radio/sim/sd as I tried flash proper rom and radio and remove sd and SIM.
my device also seems like got problem at the gps chip, because when using it for a few minutes, it will lost signal and never reconnects unless i soft reset, after use gps the device will also use battery VERY FAST(-100mA in standby, from -4mA).
now i cannot flash to stock completely, how do I get warranty it?
Click to expand...
Click to collapse
Silly question, but are you holding (and keep on holding) the Volume-Down button while you press the power button?
of course YES
i told you i have been flashing for so long
Leo from T-Mobile. Hi! I've got same problem. After flashing new (next) rom phone definetely died. Phohe is currently simfree and with HSPL. Only one reaction is short vibration after press power button. I searched everywhere. My phone has no bootloader but system see him as Qualcom CDMA Technologies MSM. Thats all, any ideas? Please and thanks for advice.
czaruch said:
Thats all, any ideas?
Click to expand...
Click to collapse
Yes, you flashed a non tmous stock rom that included a ..51.. radio and it destroyed your phone.
What rom? exact filename please.
thank you so much.
I bricked a Leo with the .51 radio. I think I read that is a European or otherwise foreign radio. Since your ROM has Euro in the name.......
czaruch said:
ROM_Leo_HTC_WWE_EastEurope_1-66.
Click to expand...
Click to collapse
The full filename for that rom is
RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Si gned_15.32.50.07U_2.07.51.22_2_Ship.exe
it comes with a version x.xx.51.x radio, and they do Not work on tmous (t mobile us) phones. They kill them
Your phone is dead, sorry. No known fix.
warranty or repair (or JTAG if you are brave and have the money)
a friend of mine bricked his phone. he then tried to microwave it, but that didn't work after that he took a power wire from an old computer, cut it and connected it directly to the phone's parts where the battery would go...this completely f-ed his phone up (he also used a lighter to fake a powersurge of the battery). Then he called htc and a few weeks later he got a new hd2!
GOOD LUCK
lol, he doesnt need to do any of that, its allready as dead as it can be. Loads of epople have had them replaced under warranty with this kind of brick. It wont start, so htc/tmo cant see that its been hacked.
Hi! I understand and realy sad. Somebody know where could I fix it in UK? And how much for this pleasure. Thanks.
i would contact htc, see what they have to say. (dont say you flashed it, it just stopped working")

[Q] Stuck in bootloader

OK title says it all, and yes I have been reading for the last 3hrs, all the possible solutions.
HD2 EU Vodafone UK
So here is what I have tried:-
Task 29 + flash stock rom - stuck -
Hard reset - stuck
remove HSPL - stuck
flash latest Vodafone rom from HTC 3.14.161.3 - stuck - also SPL now 3.03
flash old stock to downgrade SPL to 1.66 - stuck
Have also tried reinstalling MAGLDR - stuck - magldr doesn't even show.
I never get flash failed, and yet it will not get past the Tri coloured bootloader.
Also I cannot get it to flash from SD. I have tried holding the endcall and vol down but it just goes to the loader.
Vol Up and endcall goes to hard reset.
And, to make it worse, it's not even mine. I was returning it to Winmo for a mate.
Phones been running Android nand since March without problems.
All suggestions welcome.
Bixx said:
Vol Up and endcall goes to hard reset.
Click to expand...
Click to collapse
that would indicate a stuck volume down button, since hard reset is volup and voldown. (You dont need to hold power, tap and release it, its teh vol buttons you hold)
You are quite right about the vol up and down for reset.
Also, I had been considering the possibility of a stuck button.
I will see if i can prove or disprove it.
Thanks for the response.
Does anybody know how many buttons are in the volume control rocker?
Is it:-
1 for down volume
1 for up volume
and another for both when you hold both in?
I am still trying to decide if the down volume button is stuck on.
When I hold both down I can get into reset mode, but if I only press the up it still goes to tri colour.
So I am still not sure if the down is stuck on.
3 buttons in the rocker could explain why up only doesn't go to reset but 2 buttons only would confirm that the down is not stuck on.
All comments welcome
two, you can feel them click on individually when you press them.
I too can only feel 2 and that would imply that the down is not stuck.
When I hold the up button and switch on it goes to boot loader, if it was stuck shouldn't the phone have gone to reset?
I was hoping it was like a mouse wheel with forwards, backwards and click down which is 3 positions.
I'm running out of things to try.
If it's not stuck why does it keep going to bootloader with out being asked?
Why can I flash roms and HSPL without any failure messages but still find no change on reboot?
Thanks for the replies and please keep them comming
I have managed to flash from SD. I tried a different card.
I have attached a pic of the screen saying update complete, update success.
But still stuck in bootloader
well, if it isnt hardware, it must be a corrupted bootloader issue, or bad nand blocks perhaps. ive seen quite a few 'only enters bootoader' threads over the yrs, but never really noticed a solution.
sorry, no suggestions, other than perhaps give teh freezer trick a go?
I'm desperate enough to try almost anything.
I will have to read up on the freezer trick.( don't want to kill it completely)
I have also contacted a couple of repairers for a quote using Jtag. the first said "sorry bricked" and I'm still waiting for the second reply.
Also reading up on Goldcards, maybe that's another option?
Thanks again for the reply.
Bixx said:
I'm desperate enough to try almost anything.
I will have to read up on the freezer trick.( don't want to kill it completely)
Click to expand...
Click to collapse
cant hurt to try.
I have also contacted a couple of repairers for a quote using Jtag. the first said "sorry bricked" and I'm still waiting for the second reply.
Click to expand...
Click to collapse
lol, probably scared of doing it (it requires dismantling teh phone, and theyre notoriously easy to break, there are loads of threads here where someone took theirs in for a fix and the vol/bottom button/screen ribon cables got broke by the shop.
Also reading up on Goldcards, maybe that's another option?
Click to expand...
Click to collapse
could be tho unlikely (sorry) goldcard flashing is just sd flashing but bypasses carrier and region checks.
if you can get the serial of your sd card, i can make you a goldcard image, no problem. (Don't bother using the free goldcard page on revskills website, its for android and wp7 phones) . PM me the serial and an email address if you want one.
@samsamuel Thanks for all your help and advice.
I have sent it off for repair today.
As I said in the first post, it's not even mine I was re flashing winmo 6.5 so my mate could sell it.
Hopefully it will be all sorted now.
Update.
I contacted 3 repairers.
1st said "sorry dead"
2nd said "£40 + postage"
3rd said "£21 which became £29 all in"
So I sent it to 3rd one, got a quick reply "sorry unable to fix, here is a full refund" and they returned it via 1st class post.
So yesterday I've got the phone in my hands, poped in the battery and I am presented on screen with a triangle and the words "flash failed please try again"
So task 29, now back with a tricoloured screen. See attached.
Now tried a custom Winmo, and it works
So I tried 2 Vodafone and 1 O2 stock roms and they all failed at 9%.
Tried another custom Winmo, and again working
So finally, I have task 29, CLK, clockwork v5 and latest MIUI. All working just fine.
Is there a stock looking custom winmo that anybody can recommend?
Hah, a lucky outcome. The radio is stuck, hence stock roms failing, but lucky for you its still a working radio, so customs are working. About the best result you could get, considering.
I'd say try the Artemis rom, but that will require spl 3.03.hspl, and occasionally the stuck radio issue messes with changing spl,,
Not so sure about your stuck radio theory, I have been able to change the radio without an issue.
I will give Artemis rom a go.
thanks for all the support.
Merry Christmas
Bixx

Categories

Resources